BB Z10 Network Mode Choices

When I first bought my Z10, under System Settings / Network Connections / Mobile Network / Network Mode it gave options stated in terms of "G", i.e, 4G or 4G & 3G & 2G or 4G & 3G or 3G & 2G". After installing one of the leaked OS's 10.1.0.2342 these options changed to LTE/UTMS/GSM, one of which was just GSM. Selecting that option turned off 3G and restricted the phone to 2G. Now suddenly, without updating the OS, the options have changed back to 4G etc. It was very useful to be able to set the phone to GSM/2G. There is no such option in the 4G 3G option version. You cannot turn off 3G, which is a big battery user. Setting it on GSM only (2G) used to give me a good few hours more battery life a day. Do you have any idea what caused these changes? Is it OS version related or is it a user setting somewhere?

I've been using Blackberry Z10, STL100-2 model for quite sometime. I recently updated it to 10.1.0.2354. I'm now facing the issue in 'Network Mode' option. Before updating it to 10.1 it was showing all the option (2G, 3G, 2G&3G, 2G, 3G&4G) but after updating its is only showing two options 'Null' and '2G'. Any idea why it has happened and what;s the solution?

Similar Messages

Airport Express as very slow in "extend wireless network" mode

Hi!
I am using a Airport Extreme (fourth generation) as a wireless router and a Airport Express 802.11n in "extend wireless network" mode.
I've set the Airport Extreme mode to 802.11n only - and all devices connect to the Airport Extreme as 802.11n Clients properly.
But as soon as they connect to the Airport Express, they only work in 802.11b/g mode (although they are capable of n)
and the connection is very slow - around 1Mb/s:
http://imageshack.us/photo/my-images/804/bildschirmfoto20111211u.png/
Can i force the Airport Express station to accept only "n" connections to speed up my file tranfers?
Thanks for any help!
matt

Where is the AirPort Express located in relation to the area that needs more wireless coverage?
Ideally, it would be at a point that is about half the distance between the AirPort Extreme and the area that needs more wireless coverage....and....there would be no obstructions like walls and/or ceilings in the signal path....tough to do in most homes, so do the best that you can.
Avoid placing the Express down low on the wall and use an extension cord to get it up as high as possible with a free look into the room.
The Express will normally "extend" what it receives, but you could try the following to see if it helps:
Temporarily, change the Wireless Mode setting on the AirPort Express to "Create a wireless network" and change the Radio Mode to "802.11n only".
(You may have to hold down the option key on your Mac while you click on the Radio Mode selection box to see the "802.11n only" choice). Then change the Wireless Mode back to "Extend a wireless network" and Update.

Network mode: Create a wireless network vs. Extend wireless network via ethernet

Can some one tell me the difference between configuring AirPort Utility : Network mode: Create a wireless network vs. Extend wireless network via ethernet? I connect my cable modem to my Airport Time Capsule to a network switch via ethernet. The switch contacts to three Airport Express (AE connects to two Apple TVs via Ethernet) and another TC. Which is the best mode to configure my network?
Thanks

Create a wireless network is used only when the Airports have an Ethernet connection. If you are using the setup wizard.....the setting will read Extend using Ethernet during the setup. If you go back in using AirPort Utility to check the Network Mode setting.....you will see that it is really Create a wireless network.
Extend a wireless network is used only if an AirPort is connecting to another AirPort using wireless.......not Ethernet.
Every one of the Airports on your network must be configured to Create a wireless network.
If you do connect an Ethernet cable to an AirPort that is already set up to Extend a wireless network......that will create a massive feedback loop that will crash the network until you remove the Ethernet connection to the device.
The bottom line here might be if you are using the setup wizard, it will make the correct choice for you.

Network Mode Switch No Longer Possible After Upgrade

Hello. I can't switch from 3G/H+ to 2G any longer. I could do this when I still had the OS 7.0 running on my Torch 9810 (AT&T). This changed after I upgraded to the OS 7.1. Now, when I go to the "Networks and Connections" option, all I see is "Manual and "Automatic"...I don't see any options to switch between 2G or 3G/H+...Even when I try switching manually to 2G (selecting 2G from the list of available networks), it still stays on 3G/H+...I have just upgraded to the latest official release: OS 7.1 Bundle 1997 (7.1.0.694 , Platform 5.1.0.507) but still, there are no changes on that. I need to have this feature because staying put on 3G/H+ means faster battery consumption and I don't want that. Please, your assistance is needed. Thanks.

1.On the home screen, click the connections area at the top of the screen, or click the Manage Connections icon.2.
Click Networks and Connections > Mobile Network.•
To connect to CDMA networks only, set the Network Technology field to 3G.•
To connect to either a GSM or CDMA network, set the Network Technology field to Global.•
To connect to GSM networks only, set the Network Technology field to GSM/UMTS. To optimize network coverage, set the Network Mode field to one of the following: 2G & 3G or 2G & 3G/4G or 2G & 3G/H+. The options that appear in the Network Mode field depend on your wireless service provider.
Click here to Backup the data on your BlackBerry Device! It's important, and FREE!
Click "Accept as Solution" if your problem is solved. To give thanks, click thumbs up
Click to search the Knowledge Base at BTSC and click to Read The Fabulous Manuals
BESAdmin's, please make a signature with your BES environment info.
SIM Free BlackBerry Unlocking FAQ
Follow me on Twitter @knottyrope
Want to thank me? Buy my KnottyRope App here
BES 12 and BES 5.0.4 with Exchange 2010 and SQL 2012 Hyper V

Impdp in network mode - failing with ORA-39006

Import from a 10.1.0.2 database into 11.1.0.6 on Linux RH4
I believe this stems from the fact that that the target db does does have privileges to the dbms_utility package, what user do you therefore grant execute privilege in order for this impdp to work?
Error text:
Errors: ORA-39006: internal error ORA-39113: Unable to determine database version
ORA-04052: error occurred when looking up remote object

Command used was:
impdp abc_owner/tiger directory=dmpdir network_link=dp_link tables=colours version=COMPATIBLE
I ran impdp from 11.1.0.6 database.
The doc you mentioned - quotes "When operating across a network link, Data Pump requires that the remote database version be either the same as the local database or one version older, at the most. For example, if the local database is version 10.2, the remote database must be either version 10.1 or 10.2. If the local database is version 10.1, then 10.1 is the only version supported for the remote database"
Do this infer that I cannot therefore use datapump in Network Mode? - would appear so.

N73 ME not working in Network Mode GSM and Dual Mo...

Dear All,
I have N73 ME.
Firmware: V 4.0812.4.2.1
I am using Vodafone Line and I am living in egypt.
I have a problem with the network of the device. The device is working fine only with the Network Mode UMTS, but not working with GSM and Dual Mode, which makes it doesnot have network signal in many areas, while I have another Nokia 5200 phone whick works fine in these areas.
Is it a Software or Hardware problem?
and what is the solution for it?
Thanks in advance for your help.

moderator note:
please be informed that your personal and contact information, as well as the IMEI of your phone are not allowed to be posted in this board for security and privacy reasons.
thanks.

WRT610N Help with the network mode changing to an A.

Hello All,
I just purchased a WRT610n Router, the wireless n adapter, and the gaming router, My question to you the customer is have any of you had problems with the gaming router switching to a wireless A network mode , I have my gaming system on 5nhz and I want the transfer rate to be at the highest possible rate and I know switching to an A network will change that transfer rate I am only 25 feet away on one level so any suggestions would be helpful or comments as well.
Message Edited by ChrisM1981 on 01-19-2009 11:14 AM

Hello,
I have WRT610N, WGA600N, and I am on Comcast Broadband Transfer Rate Of 1GBPS on my p.c. and the transfer rate on my notebooks is 130MBPS to 230MBPS also I am running my gaming System on the Dual Band 5NHZ like I said I am on one level with nothng between the Router & Adapter so I am wondering why it is transfering to 802.11a Frequency because I know that lowers Tranfer Rate from a Wireless N Frequency so any help you can give me that would be great.
Thank you

Network Mode setting on E7

Dear all,
Im kind of new to the site as well as using my new E7. ve set ip all up and its working fine. however I kind of changed the network mode settings to be GSM from Dual Mode under connectivity to reduce my battery usage in power saving i cant access internet while deactivating this option Im able to.
I wish I can change it back at the same time use power saving mode. what do I do it keeps on changing back to GSM when I activate power saving mode
ken
Solved!
Go to Solution.

It always disables 3G radio in battery saving mode since it's the most obvious battery hog.
Since 1610

WRT610N-ver2 - Network Mode N-only disables wireless security

WRT610N-ver2 - Network Mode N-only disables wireless security
Firmware 2.00.01 build 15 Sep. 13, 2010
When I set Newtork Mode to N-only, the wireless security turns to DISABLED & can only be re-eneabled by returning to MIXED mode
Same thing on both bands.

Try to re-flash the firmware of the router once again. The re-flash process means that you will be updating your firmware with a version that is similar to the one that you are currently using. A firmware re-flash will help in fixing the script of your device’s current firmware. After re-flashing the firmware reset the router. Here is the link for resetting the router: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=eaa3127db5f4402584c959a7251e754c_4008.xml&pid=80&r...
After the process try to reconfigure the router again and then check the status..

HELP! Problem with setting up Airport Extreme in "extend wireless network mode"!

So I am trying to put my AirPort extreme in extend a wireless network mode. So I factory reset it, plugged it in, and went into Airport Utility to set it up. So it finds the device, and I set it up to extend the network. It does everything, and it gets set up. But there is an error message that says it was unable to extend the wireless network. Then 1 minute later, the Airport Extreme drops out, and the Airport Utility says device not found. I tried this multiple times, and it keeps happening. What should I do?

Unfortunately, the AirPort Extreme will not be able to wirelessly extend a Netgear product. That feature will only work if you are connecting the AirPort Extreme to another Apple router.
If you want the AirPort Exteme to provide more wireless coverage, you will need to plan to connect it to the Netgear router using a permanent, wired Ethernet cable connection.

6500 Classic 'GSM' Network mode selection unavaila...

I moved to 3 network but on their phones the network mode is locked to dual or UMTS with no provision for GSM only. This zaps the battery. I have found a way around it on the N82 by downloading FTD FieldTest app and going to FTD 81.01 where you can overide firmware restrictions and select force protocol to GSM.
Unfortunately on the 6500 Classic I cannot seem to get FTD? Please advise if it is possible to obtain FTD for this S40 device or if there is any applet that will overide this settings for me.
I've spent about 4 days solid on the net trying to resolve this as the 6500 C battery life is so bad it needs 3G turning off.

SagarS wrote:
Hello,
I don't know if anyone faced this problem or not N8 having 3 option in network selection mode
i. Dual Mode
ii. 3G
iii. GSM
But when you select Duel mode in N8 and before selecting Dual if you are using GSM mode then mobile does not select 3G and continue to using GSM network.
If you select 3G first and then dual mode after then only 3G is selected in dual mode.
As there is only two option GSM and Dual mode in Nokia N70 I could not get 3G network.
I request you all to please guide for getting 3G network on Nokia N70.
Thank You,
SagarS
The N70 supports network dual mode. The 3G sign is supported by most operators, but not all, so you could be connected in WCDMA mode without noticing. Check your manual and download speed.
http://europe.nokia.com/support/product-support/nokia-n70/user-guides
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

Unable to connect to Linksys E3000 when set to 5GHz "N" only Network mode

I've not been able to connect to my to Linksys E3000 when set to 5GHz "N" only Network mode. Connections to the 5GHz can only be done in mixed mode. I do not need to have A-Mode enabled, so I do not wish to use mixed.
Tested with a variety of adaptors, most recently my Intel® Centrino® Ultimate-N 6300 .

Thank you for your response.
I have Win 7 Ultimate.
Wireless NIC: Intel® Centrino® Ultimate-N 6300
Latest Driver: 14.0.1.2
I took your suggestions, and verified the firmware is current.
Channel Width: 40
Channel: 161
Also, I have turned security off for testing.
If Network Mode = N Only, I see and can 'connect', but then get the error below:
If "Network Mode:" = Mixed, there is a connection, but Status-> Local->DHCP Clients verifies it as "A":
w520 Wireless-A 172.222.1.33 00:xx:x7:AE:xx::0C 23:59:45
I have the latest firmware
Firmware Version: 1.0.04 build 6 Dec 6, 2010
Firmware Verification: 1ad912eecfd4c2226624cc8ff9b43820
The error from Windows is non-specific:

Nokia N82 Network Mode

Why do I could not make outgoing calls and receiving incoming calls when my network mode is in dual mode while last two months its still okay? When I try to make an outgoing call it will show connection error and while receiving incoming calls the caller will be forwarded to my voicemail. It has to be setted on UMTS or GSM mode in order for the phone to work properly. How to fix this? Please help. Thanks.
If you think what I've just post is useful, do give me a kudos! xD

This evidently has nothing to do with call diverts, so I have no idea where the above user got that idea. The phone registers to the network if forced to GSM or UMTS mode but not if set to "automatic".
This is often a software problem. Start by switching the phone off and removing the battery for 10 minutes. Then reassemble and try.
If that didn't work then you'll have to try a reset. Back up your phone's contents but not the phone's settings to the memory card or using PC/OVI Suite beforehand because this is going to erase everything.
Dial *#7370# and enter your security code when prompted (the default on all Nokia phones is 12345 until you change it).
Restore the backup you made.
If the problem persists then you'll need to contact your operator and explain the problem to them. It could be a problem with your SIM card, in which case they can perform an over-the-air update or even replace it if necessary.
Was this post helpful? If so, please click on the white "Kudos!" star below. Thank you!

Nokia 701 Restarts when it is in Dual Network Mode

Hi,
I owned a 701 since Dec'11, but recently after the latest sw update after some day s it started restarting on its own almost 10 -15 times a day. I able to drill down the root cause after some un-installation and setting changes, It only restarts when its on dual network mode when it tries to switch between 2G to 3G and vice versa.
Any one has observe this issue & any solution.
Currently I'm using Airtel network in INDIA.
For temporary if using either 2G or 3G according to my need due to the issue.
Thanks,
Amit.

i have run memtest for 11 h, no errors. I have tried to higer the volt but it dosen't have anny effect but once i put the vikt to 1.8 and it worked but then the computer got ustable

WRT350N only shows 'mixed' in network mode

Hi,
I've got a WRT350N firmware v2.00.19, now all my gear is 802.11n I want to change the network mode on the router to be N only, but the only options I see under this setting are 'Mixed' and 'Disabled'.
Anyone know how I can set it to N only?

Hi Scrooge, tried your suggestion, got the power light flashing between green and orange then pulled power to the modem and router, restarted modem first them router. Still only see mixed and disabled in the network mode drop down, i'll try it a couple more times to see if my reboot restart timings makes any difference.
Do you know the underlying cause of this? reset\reboot\unplug seems like a pretty random method?
Thanks for your help with this!

BB Z10 Network Mode Choices

Similar Messages

Maybe you are looking for