BB z10 won't start up after updating to bb link

I accidentally dropped my phone on the floor, and it won't start up.
here are the following steps that i already did:
1. I already tried to update it on the bb link, after successfully updating i remove the usb cable, however  it didn't start up. everytime i try  to do a hard reset it automatically turns off, even when im seeing the blackberry logo on the screen. it goes off again.
2. i tried also to charge it first and then the blackberry name appears on the screen  it will also automatically turns off and after that it will charge only and then again the blackberry name appears on the screen same thing happen again.
3. I tried to uninstall the bb link to my computer and install again the bb link then update it again, after the successful update. still no changes happen
4. I also tried to update the bb z10 os, in a hard way through internet explorer, nothing change still won't start up.
There's one thing that i've noticed everytime I plug the usb cable on my phone, through the computer and access the bb link, it will connect and then it will disconnect it goes on and on, as i seen on the screen. I updated the usb cable plugging in,thinking that can fix the problem but still nothing change.
I know that my bb z10 works fine up to now, because there is an instant that the bb logo appears on the screen completed loading and i can navigate it for a while like changing the language and connecting to a wifi, and the logo of my sim card appears on the screen, however it will take few seconds only, and then it will turn again to the same situation that occurs on my phone.
Please help me find a good solution regarding on my phone problem.

Since this occurred right after dropping your device it's probably damaged internally. Not much we can do here for that.
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

Similar Messages

  • Intel iMac won't start up after update of OS... anyone w/similar prob?

    Help! I recently did installs through "software update" and now my iMac won't go beyond the flat blue screen. To be more specific, it starts up, takes a long time on the grey screen with the rotating pinned circle and apple logo, then stays on the flat blue screen forever. I can move the mouse but nothing else happens.
    I'm trying to remember what the software update installed... I think it was the most recent security update, iDVD, iMovie, iPhoto and Quicktime update.
    I'd appreciate any advice or experiences you can offer. Thanks in advance.
    iMac Intel 20" 2ghz   Mac OS X (10.4.6)  

    Hi, hajime7. Welcome to the Discussions.
    1. As a general check, run the procedure specified in my "Resolving Disk, Permission, and Cache Corruption" FAQ. Perform the steps therein in the order specified.
    2. An errant Startup or Login Item maybe the cause. My "Troubleshooting Startup and Login Items" FAQ can help you pin that down if such an item is causing the problem.
    FYI: Before installing software updates, you may wish to consider the advice in my "Installing Software Updates" FAQ. Taking the steps therein before installing an update often helps avert problems.
    Good luck!
    Dr. Smoke
    Author: Troubleshooting Mac® OS X
    Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
    I may receive some form of compensation, financial or otherwise, from my recommendation or link.

  • OS won't start up after Update

    Hi -
    Not sure if this problem is unique to my Mac Book Pro or to OS 10.4.9.
    Last week Software Updater asked me to install a few updates and restart. I did - during the download and install, I got an error message for one of the several updates - sorry I can't remember which it was now. I opted to restart the computer then as that's what it seemed to want to do. Since then it will not restart. I power on the machine and the grey screen with the Apple icon and the little spinning circle comes up, and this stays like so indefinitely. I have turned off the power and restarted to no avail. I was able to start up from my OS install disk, verified the disk and disk permissions with the Utility to no avail.
    What should I do next? Reinstall OS? Is this likely to cause me to lose much data on the disk?
    Any help is much appreciated. Thanks.

    try an archive and install.
    http://docs.info.apple.com/article.html?artnum=107120
    good luck!

  • Logic won't start up after updating to 7.2.3

    Hi guys,
    Sorry to bug you again with problems but I am stuck. I just updated to 7.2.3 and now logic will not start up at all. All I get is the "The application quit unexpectedly... Would you like to: Reopen ... When I look at the crash logs in the console this is what I see, however I can't make any sense out of it:
    Host Name: **-power-mac-g5
    Date/Time: 2007-08-08 22:20:40.110 -0400
    OS Version: 10.4.10 (Build 8R218)
    Report Version: 4
    Command: Logic Pro
    Path: /Applications/Logic Pro.app/Contents/MacOS/Logic Pro
    Parent: WindowServer [72]
    Version: 7.2.3 (961.9)
    Build Version: 14
    Project Name: Logic
    Source Version: 9610900
    PID: 260
    Thread: 0
    Exception: EXCBADACCESS (0x0001)
    Codes: KERNINVALIDADDRESS (0x0001) at 0x72537760
    Thread 0 Crashed:
    0 <<00000000>> 0x72537760 0 + 1918072672
    1 <<00000000>> 0x014fc26c 0 + 22004332
    2 <<00000000>> 0x014fc158 0 + 22004056
    3 <<00000000>> 0x014fc038 0 + 22003768
    4 <<00000000>> 0x014fc000 0 + 22003712
    5 com.apple.CoreGraphics 0x903fcf40 CPSRegisterWithServer + 576
    6 com.apple.HIServices 0x918419d4 RegisterProcess + 76
    7 com.apple.HIServices 0x91841840 INIT_Processes + 188
    8 com.apple.HIServices 0x91841748 GetCurrentProcess + 56
    9 com.apple.logic.pro 0x001ec9e4 0x1000 + 2013668
    10 com.apple.logic.pro 0x0000b968 0x1000 + 43368
    11 com.apple.logic.pro 0x00003224 0x1000 + 8740
    12 com.apple.logic.pro 0x000030cc 0x1000 + 8396
    Thread 0 crashed with PPC Thread State 64:
    srr0: 0x0000000072537760 srr1: 0x100000000000f030 vrsave: 0x0000000000000000
    cr: 0x24200204 xer: 0x0000000000000000 lr: 0x00000000014fc20c ctr: 0x0000000000000000
    r0: 0x0000000072537761 r1: 0x00000000bffff500 r2: 0x0000000000000e03 r3: 0x00000000014fc1e0
    r4: 0x00000000014fcf5d r5: 0x00000000bffff578 r6: 0x0000000000000034 r7: 0x0000000000000e03
    r8: 0x0000000000000000 r9: 0x0000000000000000 r10: 0x000000000312f5c0 r11: 0x00000000afdf2a28
    r12: 0x0000000000000000 r13: 0x00000000014fcf49 r14: 0x0000000000000000 r15: 0x0000000000000000
    r16: 0x0000000000000000 r17: 0x0000000000000000 r18: 0x0000000000000000 r19: 0x0000000000000000
    r20: 0x0000000000000000 r21: 0x00000000a038cd08 r22: 0x00000000a038cd08 r23: 0x0000000000000104
    r24: 0x00000000a0390670 r25: 0x0000000000000002 r26: 0x00000000bffffd8c r27: 0x00000000afdedfe8
    r28: 0x0000000000000180 r29: 0x0000000080001513 r30: 0x00000000bffff730 r31: 0x00000000904009b4
    Binary Images Description:
    0x1000 - 0xd8efff com.apple.logic.pro 7.2.3 (961.9) /Applications/Logic Pro.app/Contents/MacOS/Logic Pro
    0x141a000 - 0x146dfff com.apple.LogicLoopBrowser 7.2 (16.3) /Applications/Logic Pro.app/Contents/Frameworks/LogicLoopBrowser.framework/Versions/A/LogicLoopBrow ser
    0x1497000 - 0x14a2fff libaafintp.dylib /Applications/Logic Pro.app/Contents/Frameworks/libaafintp.dylib
    0x14b1000 - 0x14c2fff com.apple.EHardwareSupport 1.0.0 (21. /Applications/Logic Pro.app/Contents/Frameworks/EHardwareSupport.framework/Versions/A/EHardwareSupp ort
    0x1605000 - 0x16a4fff com.apple.eloop 3.1.0 (24. /Applications/Logic Pro.app/Contents/Frameworks/ELoop.framework/Versions/A/ELoop
    0x1736000 - 0x178efff libaafpgapi.dylib /Applications/Logic Pro.app/Contents/Frameworks/libaafpgapi.dylib
    0x2008000 - 0x2268fff libcom-api.dylib /Applications/Logic Pro.app/Contents/Frameworks/libcom-api.dylib
    0x25d4000 - 0x2638fff com.apple.ecore 1.1.0 (44.4) /Applications/Logic Pro.app/Contents/Frameworks/ECore.framework/Versions/A/ECore
    0x8fe00000 - 0x8fe52fff dyld 46.12 /usr/lib/dyld
    0x90000000 - 0x9018ffff com.apple.prokit 4.0.1 (689.2) /System/Library/PrivateFrameworks/ProKit.framework/Versions/A/ProKit
    0x90293000 - 0x90344fff ATS /System/Library/Frameworks/ApplicationServices.framework/Versions/A/Frameworks/ ATS.framework/Versions/A/ATS
    0x90373000 - 0x9072efff com.apple.CoreGraphics 1.258.75 (???) /System/Library/Frameworks/ApplicationServices.framework/Versions/A/Frameworks/ CoreGraphics.framework/Versions/A/CoreGraphics
    0x907bb000 - 0x90894fff com.apple.CoreFoundation 6.4.7 (368.2/System/Library/Frameworks/CoreFoundation.framework/Versions/A/CoreFounda tion
    0x908dd000 - 0x908ddfff com.apple.CoreServices 10.4 (???) /System/Library/Frameworks/CoreServices.framework/Versions/A/CoreServices
    0x908df000 - 0x909e1fff libicucore.A.dylib /usr/lib/libicucore.A.dylib
    0x90a3b000 - 0x90abffff libobjc.A.dylib /usr/lib/libobjc.A.dylib
    0x90ae9000 - 0x90b5bfff com.apple.framework.IOKit 1.4 (???) /System/Library/Frameworks/IOKit.framework/Versions/A/IOKit
    0x90b71000 - 0x90b83fff libauto.dylib /usr/lib/libauto.dylib
    0x90b8a000 - 0x90e61fff com.apple.CoreServices.CarbonCore 681.15 /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/CarbonC ore.framework/Versions/A/CarbonCore
    0x90ec7000 - 0x90f47fff com.apple.CoreServices.OSServices 4.1 /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/OSServi ces.framework/Versions/A/OSServices
    0x90fe7000 - 0x90ffffff com.apple.WebServices 1.1.2 (1.1.0) /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/WebServ icesCore.framework/Versions/A/WebServicesCore
    0x9100f000 - 0x91090fff com.apple.SearchKit 1.0.5 /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/SearchK it.framework/Versions/A/SearchKit
    0x910d6000 - 0x910fffff com.apple.Metadata 10.4.4 (121.36) /System/Library/Frameworks/CoreServices.framework/Versions/A/Frameworks/Metadat a.framework/Versions/A/Metadata
    0x91110000 - 0x9111efff libz.1.dylib /usr/lib/libz.1.dylib
    0x91121000 - 0x912dcfff com.apple.security 4.6 (29770) /System/Library/Frameworks/Security.framework/Versions/A/Security
    0x913db000 - 0x913e4fff com.apple.DiskArbitration 2.1 /System/Library/Frameworks/DiskArbitration.framework/Versions/A/DiskArbitration
    0x913eb000 - 0x913f3fff libbsm.dylib /usr/lib/libbsm.dylib
    0x913f7000 - 0x9141ffff com.apple.SystemConfiguration 1.8.3 /System/Library/Frameworks/SystemConfiguration.framework/Versions/A/SystemConfi guration
    0x91432000 - 0x9143dfff libgcc_s.1.dylib /usr/lib/libgcc_s.1.dylib
    0x91442000 - 0x914bdfff com.apple.audio.CoreAudio 3.0.4 /System/Library/Frameworks/CoreAudio.framework/Versions/A/CoreAudio
    0x914fa000 - 0x914fafff com.apple.ApplicationServices 10.4 (???) /System/Library/Frameworks/ApplicationServices.framework/Versions/A/Application Services
    Any help with this is greatly appreciated... I really don't feel like reinstalling from scratch logic
    Thank you in advance.
    p.s. THe machine is dual g5 2ghz, w/ 2.5gb ram. Interface is Metric Halo ULN-2, with only a Mackie Control Universal and a M-Audio Keystation 49 midi controllers connected.
    tim

    hi xs4is, thanks for the reply
    No, that's not the problem, I mean it installs perfectly from the DVD -- no errors, no indication of any problems whatsoever, however when I double click the app to start logic up, instead of starting up I get the error message: The Application Logic Pro has unexpectedly quit. What would you like to do: Close, Reopen, blah blah, not even a splash screen shows up. nothing. I am using Onyx on a regular basis and have been running all cleanup and optimization scripts in it. didn't help at all. And I really don't want to create a second user on my machine -- it's only my machine, nobody else uses it, and I have only had problems with multipe users in the past (especially with authorizations and stuff), but I also don't think it has anything to do with accounts
    Message was edited by: phile

  • MacBook Pro won't start up after update

    I just updated my MacBook last night and now when I turn it on it gets to the grey apple screen and shuts down.

    Reset PRAM: http://support.apple.com/kb/PH4405
    Try a normal boot.
    Perform a Safe Boot:  http://support.apple.com/kb/PH14204?viewlocale=en_US
    Try a normal boot.  If it boots reliably with a Safe Boot but not a normal boot then it is probably a software issue.  Post back for more instructions.
    If you do not have a recent backup create one in case your disk is failing.  (Post back if you need instructions on how to do that w/o booting OS X.)
    Boot in Recovery Mode.  (Hold down the Command (⌘) and R keys as your computer restarts.  If you are running 10.6 or earlier boot from an installation disk.)  Run Disk Utility.  Click on the upper left system disk icon.  Does S.M.A.R.T. report “Verified”? 
    If it does not say “Verified” then the disk or the disk cable is failing and will need to be replaced.  As noted above, if it is failing the first priority is to back it up. Post back for more instructions for emergency data recovery and replacing the disk or its cable.
    If the S.M.A.R.T. status is “Verified” then repair the disk.  Click on the icon underneath and indented to the right, usually called “Macintosh HD”.  Repair Disk.  It should finish normally with a green OK message.  If it does not try to repair it again.
    If it will not finish with a green OK message then having a backup is again essential.  The remedy is a clean install:  backup, reformat the drive (erasing all the data), reinstall OS X, and then restore form the backup.  (Post back if you need instructions on how to do any of those steps.)
    If it repaired all errors (green OK) and is still not booting normally “Macintosh HD” icon again and Repair Permissions.  Ignore the numerous messages in black.  It should finish with a green OK message.  If not, run it again.
    Once you have repaired the disk and the disk permissions, if it will not boot properly, reinstall OS X: 
    Boot in Recovery Mode and then install OS X.
    If it is still not booting normally after the reinstall then, as a last resort, perform a clean install.  Make sure you have a current backup (Time Machine or a clone).  Boot in Recovery Mode.  Use disk utility to erase the system disk (deleting all data).  In the Erase tab click on Security Options… Select “writes a single pass of zeros.”  This will write to every block on the disk, mapping out bad blocks.  Install OS X.  Reload your data from the backup.  (On the first boot the Migration Assistant should as you to restore from your backup.)

  • MacBook won't start up after update

    Last night I updated my MacBook and now it will not turn on past the White screan with the grey apple logo.
    I reset the PRAM an the PMU, held down the D key an tested for hardware problems and nothing has helped.
    Any help would be very greatly appreciated as I am working on an important project on my laptop.
    Thanks in advance, Hannah.  

    put you the mac os x cd in the drive and when you start up the system press the C letter and hold it until it is loaded with the cd then find the open disk utility option from the utillities section on the top bar then try to verify the permissions and repair them this should work and bring up the os
    you can use this link for more information and step by step guide : http://kb.wisc.edu/helpdesk/page.php?id=3810

  • E63 won't start up after updating software update....

    hi,
    it's my first time to connect my e63 to my PC using usb cable..Through Nokia PC Suite, i have updated my cellphone for new softwares. during the process like,Back up and installation went well until such time that my e63 shut off and the PC prompts that there was an error occured.
    Since then my cellphone wont start up anymore though the battery is fully charged.
    Help please..
    ann

    Did you wait when the Phone got switched OFF to see if it starts again ( sometimes it takes 2-3 minutes for the phone to switch ON)  ? During the Update, the phone switches OFF and ON on its own a no. of times. A message in this regard is displayed when you start the Update process, which also says to neglect all errors getting displayed on your PC about the phone being disconnected.
    You may have a look at THIS resource. If nothing works, you need to visit Nokia Care.

  • Macbook won't start up after updates.

    I installed some software updates yesterday inlcuding Itunes 10.5, Safari and some other things. But once it tried to restart all I got was a black screen and a constant whirring noise. I left it for a while but nothing happened, occasionally it flickered for a split second.
    I held down the power button and restarted it and it worked but would shut down everytime I lowered the lid. Then I put it to sleep manually and when I tried to use it, the black screen and whirring noises came back and it's still like that. I'm not sure what to do, help?
    Fairly new Macbook Pro 13'' purchased in about April this year

    Another victim!
    Try booting up from the install disc (insert and hold down C), then run disk utility and and check your drive for errors, and then if possible try fixing them.
    This didn't work for me, however after deleting my hard drive and repeating the above procedure no errors were found, and after a reinstallation of OSX my computer is working although extremely slow.
    As for recovering your data I'm not sure. So far I haven't heard of it being done, although I have heard of new hard drives needing to be purchased.
    Good luck. And spread the word!

  • IPhoto won't start anymore (after update to 9.2.1)

    Hi all,
    I have been getting this message when I try to start iPhoto, including when starting it with cmd and alt pressed.  Can someone please help me?
    Thanks in advance.
    Process:         iPhoto [44262]
    Path:            /Applications/iPhoto.app/Contents/MacOS/iPhoto
    Identifier:      com.apple.iPhoto
    Version:         9.2.1 (9.2.1)
    Build Info:      iPhotoProject-628000000000000~3
    Code Type:       X86 (Native)
    Parent Process:  launchd [137]
    Date/Time:       2011-11-23 21:34:51.028 +0100
    OS Version:      Mac OS X 10.7.2 (11C74)
    Report Version:  9
    Interval Since Last Report:          47776 sec
    Crashes Since Last Report:           1
    Per-App Crashes Since Last Report:   1
    Anonymous UUID:                     
    Crashed Thread:  0
    Exception Type:  EXC_BREAKPOINT (SIGTRAP)
    Exception Codes: 0x0000000000000002, 0x0000000000000000
    Application Specific Information:
    dyld: launch, loading dependent libraries
    Dyld Error Message:
      Library not loaded: /Library/Frameworks/iLifeFaceRecognition.framework/Versions/A/iLifeFaceRecognit ion
      Referenced from: /Applications/iPhoto.app/Contents/MacOS/iPhoto
      Reason: image not found
    Binary Images:
        0x1000 -   0xd1afeb  com.apple.iPhoto (9.2.1 - 9.2.1) <68601E93-E4CF-3B4C-AFFD-4781A92DD58B> /Applications/iPhoto.app/Contents/MacOS/iPhoto
      0xe83000 -   0xf63fe7  org.python.python (2.6.7 - 2.6.7) <61DBA92A-C39A-3A52-86F2-59CF9D310CB4> /System/Library/Frameworks/Python.framework/Versions/2.6/Python
      0xfae000 -  0x114effb  com.apple.geode (1.5 - 151.51) <28D29759-F356-3608-B9CF-3031F3299B1B> /Applications/iPhoto.app/Contents/Frameworks/Geode.framework/Versions/A/Geode
    0x11ee000 -  0x11f0fff  com.apple.iLifePhotoStreamConfiguration (2.2 - 2.2) <4FA61CE9-1718-3E07-9896-0023A2A49699> /Applications/iPhoto.app/Contents/Frameworks/iLifePhotoStreamConfiguration.fram ework/Versions/A/iLifePhotoStreamConfiguration
    0x11f6000 -  0x1205fff  com.apple.iLifeAssetManagement (2.0 - 2.33) <8346DE35-5F86-3338-9913-B035B3EE5435> /Applications/iPhoto.app/Contents/Frameworks/iLifeAssetManagement.framework/Ver sions/A/iLifeAssetManagement
    0x1212000 -  0x123affb  com.apple.iPhoto.Tessera (1.1 - 60.10) <7BA9184E-0A00-3083-8322-772ECBDD30C9> /Applications/iPhoto.app/Contents/Frameworks/Tessera.framework/Versions/A/Tesse ra
    0x124b000 -  0x1272ffb  com.apple.iPhoto.Tellus (1.3 - 60.10) <4AABB0BC-AC97-3EE4-BF0F-D8499DDB57C0> /Applications/iPhoto.app/Contents/Frameworks/Tellus.framework/Versions/A/Tellus
    0x1287000 -  0x1291fff  com.apple.iphoto.AccountConfigurationPlugin (1.2 - 1.2) <3B68F126-D783-3F86-AF04-A0F6A459BE67> /Applications/iPhoto.app/Contents/Frameworks/AccountConfigurationPlugin.framewo rk/Versions/A/AccountConfigurationPlugin
    0x8febe000 - 0x8fef09c7  dyld (195.5 - ???) <134323A7-49DC-3A9D-ACFD-32FAD0FD6BA2> /usr/lib/dyld
    Model: iMac7,1, BootROM IM71.007A.B03, 2 processors, Intel Core 2 Duo, 2.4 GHz, 4 GB, SMC 1.20f4
    Graphics: ATI Radeon HD 2600 Pro, ATI,RadeonHD2600, PCIe, 256 MB
    Memory Module: BANK 0/DIMM0, 2 GB, DDR2 SDRAM, 667 MHz, 0x7F7F7F7F7F5D0000, 0x436F6D707573746F63782028435358292020
    Memory Module: BANK 1/DIMM1, 2 GB, DDR2 SDRAM, 667 MHz, 0x7F7F7F7F7F5D0000, 0x436F6D707573746F63782028435358292020
    AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x88), Broadcom BCM43xx 1.0 (5.10.131.36.11)
    Bluetooth: Version 4.0.1f4, 2 service, 18 devices, 1 incoming serial ports
    Network Service: Ethernet, Ethernet, en0
    Network Service: AirPort, AirPort, en1
    Serial ATA Device: WDC WD3200AAJS-40VWA0, 320,07 GB
    Parallel ATA Device: PIONEER DVD-RW  DVR-K06A, 111,5 MB
    USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd400000 / 2
    USB Device: SDDR-189, 0x0781  (SanDisk Corporation), 0xb7bd, 0xfa400000 / 3
    USB Device: Keyboard Hub, apple_vendor_id, 0x1006, 0xfa200000 / 2
    USB Device: SCX-4623 Series, 0x04e8  (Samsung Electronics Co., Ltd.), 0x3434, 0xfa210000 / 5
    USB Device: Apple Keyboard, apple_vendor_id, 0x0221, 0xfa220000 / 4
    USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x5d100000 / 2
    USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8206, 0x1a100000 / 2

    You need to reinstall as iPhoto is missing bits of itself.
    To re-install iPhoto
    1. Put the iPhoto.app in the trash (Drag it from your Applications Folder to the trash)
    2a: On 10.5:  Go to HD/Library/Receipts and remove any pkg file there with iPhoto in the name.
    2b: On 10.6: Those receipts may be found as follows:  In the Finder use the Go menu and select Go To Folder. In the resulting window type
    /var/db/receipts/
    2c: on 10.7 they're at
    /private/var/db/receipts
    A Finder Window will open at that location and you can remove the iPhoto pkg files.
    3. Re-install.
    If you purchased an iLife Disk, then iPhoto is on it.
    If iPhoto was installed on your Mac when you go it then it’s on the System Restore disks that came with your Mac. Insert the first one and opt to ‘Install Bundled Applications Only.
    If you purchased it on the App Store or have a Recent Mac you can find it in your Purchases List.

  • My macbook pro won't start up after updating it

    I Have a macbook pro with Mavericks (I don't remember exactly which one) which I bought in 2012, yesterday night I updated it and it restarted but it took forever and I thought it was installing something, so I left it like that all night and day and is still in the gray screen with the apple logo and the wait spiral. I got worried so I entered the disk utility option and checked the disk, and it said everything was Ok. When I restarted it again, the gray screen never left so I tried with the "safe rebooting" ctrl + cmnd + V and the screen shows now endless rows of "disk0s2: 1/0 error."  and it's been like this for about half an hour now, I'm really worried I'll my data.

    An 1/O error cannot be repaired by Disk Utiity.
    That requires a more robust disk utility such as DiskWarrior
    You can contact the developer using their email address here.
    Best to get their recommendation before purchasing.
    Hopefully you have a backup  to restore from once the drive is either repaired or replaced.

  • Iphone 6 won't start up after new update

    iphone 6 won't start up after update, what can I do?

    And it stops at that screen and that is all that shows? Then you need to try and force the device into Recovery Mode and restore. See the instructions in this support document. If you can't update or restore your iPhone, iPad, or iPod touch - Apple Support

  • Z10 won't start

    I had problems with my BBM in my Z10 so I had to do a security wipe to get it working again after I did the security wipe every time I start my phone it tells me to connect it to my PC and I did but still won't start I had tried the blackberry link and the internet explorer thing but still it won't work 
    any HELP plzzz ???

    HELP!!!!

  • My Ipod touch plays music but every time I open an app that I have downloaded it closes immediately.  This started happening after updating to the latest version of Ipod software.

    My Ipod touch plays music but every time I open an app that I have downloaded it closes immediately.  This started happening after updating to the latest version of Ipod software.

    Here's a couple things to try:
    1. Reset the iPod by holding the sleep/wake button and home button at the same time for 10-15 seconds until the Apple logo appears on the screen.
    2. Uninstall and reinstall one of your purchased apps. Sometimes this can rectify the issue.
    3. Connect the iPod to iTunes and restore it. New system software usually resolves the issue. Make sure you sync before restoring because a restore removes the data from your iPod.
    Hope one of these works for you!

  • Mac OSx won't boot up after update to 10.6.7?

    Mac OSx won't boot up after update to 10.6.7?

    Hi Mike
    This is called a kernel panic, similar to s 'blue screen of death' on Windows. When you say you reinstalled 3 times, do you mean the OS or the Update?
    When does this kernel panic appear? You may have a hardware issue if it's happening on boot.
    Taylor

  • MacBook Pro won't start up after chime, MacBook Pro won't start up after chime

    MacBook Pro won't start up after chime, MacBook Pro won't start up after chime

    Try resetting the SMC.
    Barry

Maybe you are looking for

  • Embedded spaces in words

    I am using Adobe Reader Version 9.4.5.  When I select, copy and paste certain content from a pdf file into another tool, say MSWord, Outlook, or even into Adobe Reader's seach box, the words sometimes include embedded spaces.  For example, the word "

  • ITouch going to apps on its own

    I have tried looking for an answer and can't find one. My iTouch will be on the home screen and go to different apps and go back to the main screen and enter another app and do whatever it wants to with out me touching anything. It will speed up my v

  • Can someone tell me where to get information about the search function in Swift

    I need to put a search function into an app I am building and I have no idea where to look for information as to code, where to put the code and the text that it is going to search ( a book's worth) where do I put that file.  Any help would be great.

  • Uninstall an OSX or Pro Apps Update

    Hi, I would like to be able to reverse an update after installing it because sometimes that update creates a confilct with other applications running, such as in my current case. I installed a pro apps update and now postgresql will not start... Is t

  • Help wih masking

    I need help with a masking problem. When i try and mask a new line, as shown in the flash video bellow, the previous masking layer will over mask the new line. How can i stop this from happening and is their an easier way to do this. I have never use