BC 2.1 vs 2.0, graphics, boot disk

Hi,
I have a couple of issues/questions with bootcamp.
System:
quad 2.66, 1st gen 23" HD cinema display.
Drive 1&2: Raid, 10.5.3 boot drive.
drive 3: OSX 10.4.x
Drive 4: 1 mac partition, 2nd partition is windows XP Pro.
Bootcamp 2.0
Basic XP install, then the 100 odd post SP2 security updates and requisite reboots. Install QTime, Safari, IE7, Office 2007 Enterprise, and updates to same, flash player...All with requiste reboots.
Everything worked, to include the nVidia (change resolution, color depth, refresh rate) app in the system tray.
Screen was bright, clear, and all colors are accurate.
Lone Problem: bootcamp did not show the RAID as a startup disk option.
The only 2 drives shown were 10.4 and Windows.
Install Bootcampt 2.1.
reboot.
=====
Problem 1: 10.5 still not shown as a startup disk option
Problem 2: nvidia app in system tray no longer present.
Problem 3: Screen is now very dark.
Attempting to adjust brigness/contrast/gamma through the standard nvidia control panel accomplishes nothing beyond oversaturation and washing out the screen.
Changing resolution, color depth, refresh rate makes no difference.
Of the 3 problems, 1 and 2 are annoying, but minor.
3 is the real problem, and pretty much makes the system unusable.
Considering removing BC 2.1 and going back to 2.0.
Anyone else done that w/o negative effects?
Other ideas for a fix?
Thanks,
AJ

Reinstall latest nVidia drivers.
Unfortunately, that didn't work But it was worth a try
Remove/reinstall bootcamp also didn't work.
I know before installing Windows and BC, everything was set right and looked correct on the Mac side.
Needed to check email, so I booted back to 10.5.3 (for the first time since installing windows, etc) a few minutes ago.
Noticed the screen was darker there, too.
Apparently, something 'adjusted' the screen brightness all the way down.
Boosted the brightness up about 1/3, rebooted to Windows, and lo and behold, all was better there, too.
I'm guessing something during the install and config of bootcamp 2.1 update somehow reset the brightness value in PRAM.
Thanks!
AJ

Similar Messages

Is it possible to detach an external firewire BOOT disk during sleep?

Hi,
I have an aging PowerBook G4 17 inch (3 years and 3 months) which is still good and fast enough for my needs. Last year the display and motherboard were changed which cost me some money so I would like to hold on to it for one or two more years. Yesterday I suddenly heard a strange noise coming from the hard disk and the Finder and Disk Utility ran extremely slow afterwards for some time. I shut it down, waited a couple of hours and now everything seems to be normal. I take it the hard disk might soon die (Toshiba make, more than 3 years old, a lot of graphics work requiring disk activity). Or 1° I replace the internal hard disk or 2) I buy an external firewire disk to boot from (which I can continue using afterwards if the laptop goes dead). I am leaning towards the second solution. However I would like to know:
1. Is it good behavior to put the computer to sleep, detach the hard disk (from which I booted) and attach it before waking it again? This would make it easy to transport it. I did a test and it seems to work however one test might not be conclusive...
2. Would my system be as fast as with an internal one (assuming I buy an external FireWire 800)?
Any feedback would be greatly appreciated!
Thanks!
PS: what is the average life of a PowerBook? The sales guy from a local Apple shop told me that after 4 years any Mac is good for the trash.

The sleep removal will work as long as the battery doesn't go flat but is not really good practice to remove a boot disk after startup.
Speed would be reasonable but internal would be better, replacing the internal drives on AlBooks is a bit fiddly but it can be done, see here for a guide.
The guy in the shop was trying to sell you a new Mac, there are people out there still using 10+ year old Macs!

Boot Camp not installing Windows 7 - "No bootable device, insert boot disk and press any key."

I need some help with something. A while back, I put a brand new hard drive in my MacBook, a 500 GB model to replace the 120 GB one. I cloned everything successfully to the new drive via Carbon Copy Cloner, but now I want to make a Boot Camp partition on the drive. The SuperDrive in it is defective, so I use an external FireWire drive. So far the Boot Camp Assistant in 10.7 Lion works fine in creating the partition, but when it gets to the part where it tries to boot into the Windows installation disk (32-bit Windows 7 Home Premium, or could the 64-bit work fine as well?), it shows a black scree nwith "No bootable device, insert boot disk and press any key." I try pressing keys, but nothing happens.
I also tried using rEFIt, but that didn't work out either.
Here are the specifications of my machine...
MacBook (Early 2009 model)
2.0 GHz Intel Core 2 Duo processor
4 GB of RAM
500 GB SATA hard drive
Dual-layer SuperDrive (defective, may replace it once I have the cash)
NVIDIA GeForce 9400M graphics chip
Mac OS X 10.7.2 Lion
Can anyone help me out with this? Is there some sort of workaround?

Wiley207 wrote:
Believe it or not, it was the FireWire drive that was the problem! I managed to successfully install Windows 7 using an external USB DVD drive!
Well I am truly staggered, I have tried this on two different MacBook Pros, with three different external USB optical drives. Don't know if you googled as I suggested but you would find hundreds of others who have found same thing. The exception is MacBook Air which works with the Apple writer, but I don't know much about this.
Were you doing any of the special workarounds with refedit etc?
What model USB DVD drive?

Making a boot disk w/ partition

So, I've made a boot disk. (Basically, a mirror of my SSD HD) But, over time, I've realized it's a waste of space. I'm only using a fraction of the 1TB drive.
My question is: Can someone give me a step-by-step on how to create a bootable disk, but with a sizeable partition on the side?

Open the Disk Utility program in the Applications > Utilities folder, and then select your external hard drive device (it will be called something like "1TB Lacie..."). When you do this, a "Partition" tab will appear, so click this and then click the graphical schematic of the partitions that appear (it will have the name "Boot BACKUP" in the middle of it).
Next click the plus button to add a new partition. You can drag the separator between these partitions to resize them according to your needs, and then click Apply to save the changes. You should now have a secondary usable partition on the external drive, along with the current bootable one.

G62 notebook won't boot from boot disk

Need to recover computer. I ordered a boot disk from HP. The disk arrived and my G62 notebook will not book from boot disk. I checked the bios and it is set to boot from CD. I also started in safemode and can't locate an autorun exe when I launch explorer.
Basically my computer was hijacked with a nasty virus that has completely taken over my PC. If I boot normally all I see is an empty desktop and an start menu, can't even get a run prompt. The virus is disguised as anti virus software and is trying to get me to pay for their $90 software suite to "correct" the problem.
If I hit F11 at start up, the recovery stalls and I get an eternal blank screen.
Any suggestions?
This question was solved.
View Solution.

Hi, Courtney:
Try the free Kaspersky rescue CD.
That disk will get rid of viruses like those and the good thing is you don't need to be in Windows to run it.
It is a bootable CD (which you make from the download file) and using the graphic user interface (GUI) you can scan your PC for viruses and remove them.
Link and instructions below:
http://support.kaspersky.com/viruses/rescuedisk
Rather than changing the boot order, just start the notebook and at the beginning of the HP welcome screen, tap the F9 key to launch the one time boot menu. Select the DVD Rom drive and hit the enter key.
You should then see a message displayed on your screen that states in substance: "Attempting to boot from DVD...Press any key to boot from DVD..."
Press any key and the DVD or CD should boot up.
Paul

Can I move the OS X boot disk from a core 2 duo mini to a new i5 mini and have it boot and run normally? Some info suggests I can.

I have a 2.53ghz core 2 duo mac mini. I just purchased an i5 2.5ghz mac mini (with amd 6630m graphics).
Can I simply ermove the OS X boot disk from the core 2 duo mini and put it into the i5 mini and have the it boot up and run fine?
Some info I read suggests I can do this and it should be no problem and will work fine.
I am running 10.9.3 of OS X.
Thanks.

- I would connect the two via FireWire
- Boot the new one Target Disk Mode
- Boot the old one in Recovery
OS X: About OS X Recovery
and then uses disk utility to restore the HD on the new computer from the starup disk of the old one.
You could also boot the old one normally, download SuperDuper and the clone the old one's startup disk to the new one.

Neo4 K8N Plat SLI - Boot Disk Failure :(

Having installed Windows XP Proffesional, I installed the graphics card drivers and was asked if I wanted to restart. I went ahead and restarted, and was confronted with the "boot disk failure..." error message.
I eventually decided to reinstall Windows but when the "press any key to boot from CD" message came up, in an act of defiance, I decided that I wouldn't press any key at all.
I was suprised to see Windows load up.
Booting without the Windows CD in the drive results in the error. With the CD in the drive it boots - what could be causing this? The mobo, the HDs, the OS?

The Samsung ... yes, that's a sad story ...
I'm one of the people who believes that two disks in a SATA Raid don't nessecarely have to be the same brand. It even haves some pro's to not use the same types of disks, but that's another topic. They should, however, be the same size of course. I used one Samsung spinpoint (120GB) and a Western Digital Caviar (120GB) in a Raid-0 array. On the Dutch forum this array is known as "RAID-UI" . It worked pretty well, no crashes, pretty fast data transfers ... but then, one day, I had a hickup using Ghost. I saw: Creating image of C: 23% complete ... And it stood there for a very long time. After that, Ghost shut down giving an I/O error. I investigated the error and becam aware that there were disk errors on C: (one partition of two on the SATA RAID-UI). I had the whole lot repaired using CHKDSK and everything seemed OK again.
I looked in the VIA Raid tool and saw a difference in size between "capacity" and "real capacity" of about 0.064MB on the Samsung. Well, nothing to cry about yet. But I kept on getting disk errors and I kept on having to run CHKDSK. After a week I lost over 25MB and every day I lost more to bad clusters. Knowing that two striped disks have to be the same size, I started to wonder when this raid would crash. But, since I don't like the idea of suddenly loosing a 220GB disk array, I decided to throw out both the Samsung and the WD. (The WD is in another PC). I bought two Seagate disks and didn't go back to Samsung, because of the terrible answer I got from Samsung Holland.
I mailed them about the broken disk and asked for a replacement (disk is about 13 months old and there's a two year waranty). They simply refused to give me a replacement. They stated that I probably messed around with the disk, cause of the bad clusters. Stupid anser, to my opinion. The disk simply died from one day to the other.
Note that this disk has always hung right behind an inlet fan! So it never got hot.
I'm very happy with the seagates now. They're more quiet and ... FASTER! I get data-transfers of about 94-96MB/s, while with the other array the max was about 88MB/s.

Help creating a boot disk for ailing powerbook (and journalist!)

Hello, I'm a journalist with a desperate need to recover my Mac.
My Powerbook G4 (operating 10.4.8 I believe) was working fine until I did the latest suggested Mac software upgrade of Safari. Immediately Safari stopped responding hanging up or quitting. So I tried the next recommended update, thinking perhaps the two went together: Security 2008-009 I believe. It required a restart, which I did. (Note: I didn't do the recommended Java or Quicktime update at the same time because I'm currently working in Sierra Leone with terribly slow internet and figured I'd get to it later).
Now, however, the computer won't boot up. I hear the tone, I get the gray screen with the apple, I get the blue screen, I get the opening OS X screen and the blue progress bar, which then quits early on. Then I get a blue screen of alternating hues, which continues infinitely.
I tried all the Apple and web-suggested fixes. I cannot enter safe mode and can only perform functions with the single user mode. I've tried fsck and it said my HD is fine. The problem, I suspect, would be easy enough to fix if I could just reinstall OS X with my CD. However I am currently 7000 miles from home and CD, and in desperate need of my laptop in order to continue my volunteer work.
I do have access to a friend's MacBook Pro 10.4.9 and the internet. I have downloaded Carbon Copy Cloner... however I don't know which files I need to copy in order to create a boot disk. Nor do I know how to create a boot disk to actually put into my computer. I have also been scared by the CCC literature that says I need to erase the target volume... which in this case is my external hard drive containing all of our video footage from the last 8 months!
I use my computer every day, however I am a newbie at using things like Terminal and higher order functions that these occasions seem to require. CCC's Help manual, for me, might as well have been written in hieroglyphs (which, come to think of it, would have been easier as I seem to understand pictures well enough).
I would be eternally grateful for any simple or step-by-step advice which might help me get back to work. I'm training African journalists, and without my computer to edit, we cannot do a thing!
Thanks,
Kim

Here's some trouble shooting methods that I've copied from Apple KB articles:
Resetting PRAM and NVRAM
Shut down the computer.
Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously.
Turn on the computer.
Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time. Release the keys.
If zapping the PRAM doesn't work, try resetting the PMU.
Warning: Resetting the power manager also resets date and time settings. Performing a PMU reset returns the iBook and PowerBook hardware, including NVRAM, to default settings and forces the computer to shut down.
PowerBook G4 (DVI) and PowerBook G4 (1 GHz/867 MHz)
If the computer is on, turn it off.
Disengage the two keyboard latches located between the Esc and F1 keys, and the F11 and
F12 keys. (You may also need to disengage the keyboard locking screw located between the
F5 and F6 keys.)
Lift the keyboard. To ensure no harmful static electricity is transferred to the computer,
properly ground yourself before performing this procedure.
Press and release the reset button located on the upper right side of the logic board near the power button, shown here. Wait 5 seconds.
Press the power button to restart the computer.
PowerBook G4 and PowerBook G4 (Gigabit Ethernet)
If the computer is on, turn it off.
Press and release the reset button located on the rear panel of the computer between the
external video and modem ports. Wait 5 seconds.
Press the Power button to restart the computer.
HTH!

Unable to Log and Capture AND make FCP a boot disk

I am unable to go into Log and Capture mode in FCP 4. I can capture from firewire using I movie just fine so I know the sytem works. The minute I open Log and Capture from within FCP (with the JVC Mini-DV camera hooked up thru Firewire), it crashes. Help. I upgraded from FCP 3 to FCP 4 a couple years ago and it hasn't worked right since. Would re-installing the FCP 4 upgrade work? Also, my system works very sluggish. Please explain to me how I would make the veersion of FCP 4 my boot disk. I realize that I can't have the FCP 4 application and the media on the same drive but is there a way to partition one of my drives and make FCP one of the startup disks? Hope this isn't too confusing. Thanks.

First off, FCP 4 was darn unstable. FCP 4.5 is a free upgrade and is STILL the most stable version out there. FCP 5 is getting there.
Secondly, try:
Shane's Stock Tip Mantra: If the program was working fine, and now isn't, or just isn't working the way it should, the first things to do are:
1) Trash your FCP preferences. Download the appropriate version of FCP Rescue at http://fcprescue.andersholck.com/ and run it.
2) Open the Disk Utility and Repair Permissions.
As for partitioning the hard drive, that isn't necessary. Hasn't been since FCP 3.
Shane

Cannot get MacPro to allow me to boot to an alternative boot disk. Can choose in control panel but will not use the disk to boot. Also won't boot using disk selected using option key

My primary boot disk is encrypted as is a secondary boot disk (backup) but I cannot boot using any other disk. System 10.8.5, MacPro 4.1.
All disks mount using primary boot disk. All disks check out as OK and I have repaired permissions.
When I choose in the control panel the Mac boots but will always use my original boot disk.
When I select the disk using the option key at startup, the boot process stalls with a grey screen and a spinning cursor.
Thanks,
Dave

Still trying to figure this out. I erased the drive, did a format using disk util and then re-installed the system but I still cannot get the disk used as a startup drive. I also tried an external firewire drive and it won't allow me to boot from it either.
I can choose it starting up with the option key but it just gives me a blue screen and the spinning cursor.
If I select it in the startup pref pane it boots into my other startup drive only.
DaveLon

Do I need to change boot disk partition types - if so how?

I set my boot disk up with several partitions, one of which is the Apple_UFS partition type. I now want to be able to use if for Mac data files - pdfs, word docs, etc. (I'm running 10.4.11 on a powerpc - when I can afford an Intel macbook, I'll upgrade to Leopard).
I have some questions:
1) Will puttting Mac files on a Apple_UFS volume cause problems (rsource & data forks in files)? (If its OK, then skip to Q6 &Q7 which I'd like to know for future reference).
2) Should I change the partition type (to Apple_HFSX)? There's no data on it now, so that's not a problem.
3) Disk Utility won't let me change partition type, only change the name. Diskutil has the command " eraseVolume format name device", but I suspect that format is the current format, not a new format - please correct me if I'm wrong.
4) pdisk interactive mode has the "t" command which looks like what I want.
5) after the partition type is changed, I presume I then need to use newfs_hfs -
6) I am confused about the device/partition name - "diskutil -l" shows "/dev/disk0" with the partition I want to change as "disk0s11". "pdisk - l" shows "/dev/rdisk0" and the partition number as 11. The "newfs_hfs -h" gives an example of "newfs_hfs -v Untitled /dev/rdisk0s7". So in my case, is my device "/dev/rdisk0s11"??
7) I have an external firewire drive that also is partitioned. "pdisk -l" and "diskutil list" give different outputs - partitions 1-9 are the same on both (Apple stuff), but pdisk show several "Apple_Free" partitions that diskutil ignores - pdisk has 23 total partitions, hdutil has 18. So which number do you use for the disk-identifier?
Thanks for any help on this confusing matter.

The regular versions of PSE 10 have the same kind of automatic updating (just go to Help>Updates and let the updater do its thing) that full Photoshop has. You can update the raw converter in the app store version, but since apple requires that everything in app store programs has to live within the app package itself, the file paths are different, so unless adobe updates the whole program so you can update through the app store, the adobe updater doesn't know what to do. You can do it manually, but it's kind of complicated to dig everything out of the adobe update, not as simple as it was in older versions of PSE.
This thread over at the adobe forum gives you the general process for updating the app store version:
http://forums.adobe.com/message/4106312#4106312

[Sol 10 11/06 SPARC on Sun Blade 2500] Could not determine boot disk?

dear all,
I have a problem during installation of Solaris 10 11/06 Sparc on Sun Blade 2500. After I choosing "Initial Install" at "Select Upgrade or Initial Install" stage, appears the following error message :
"Note : Default install is not possible. Default boot disk could not be determined"
I have already concerned that the installation DVD is well burned, and the DVD-ROM is worked, but I'm not sure that the HD itself is well or defect. Could anyone tell me or figure out how would I do?

Most likely you have a disk problem. I think it may not have found a disk. If the install process left you in a shell, I would suggest using format, to see what it thinks. My guess it does not see any disks.
Another option from the ok prompt (also called OBP), is run probe-scsi or whatever the device type it. Check the options available at the ok prompt.

White Screen at Boot When Attempting to Access Recovery or Select a Boot Disk

Introduction
I want to share a solution for a problem I encountered that Apple technical support was unaware of (they said they would create a new kdoc when I called them to share my problem and its solution) and for which I could find no documentation online.
First, this is really a tip rather than a question, but I did leave it marked as a question in case anyone wants to earn some points by responding with a different solution to the problem I am about to describe. Additionally, I do not have a enough points to post a "Tip" so I am just starting a discussion instead.
Next, when I encountered the problem I am about to describe, I had not yet enabled a firmware password.
Finally, a massive "Thank you!" to the Great Pondini (James Pond - http://pondini.org) for helping me learn so much more interesting stuff about various OS X features and functionality (all for no charge) over the years.
Now on to why I have started this discussion...
The Problem
I recently purchased a new MacBook Pro (Core i7, SSD, etc.). After working with Setup Assistant to transfer everything from the most recent Time Machine backup of the older MBP I was replacing, applying all OS updates, and then enabling FileVault 2 and letting the requisite disk encryption process complete, I decided to I would go ahead and just proactively repair any permissions and ACLs for my user directory just in case any repair was necessary.
However, after shutting down my MBP, waiting, and then starting it up with Cmd-R being pressed while turning the MBP on, nothing would happen - I would just have a white screen with no Apple logo, no EFI login, no Recovery Console, nothing (and I waited for a very long time for something to show up). My only option was to do what I really do not like doing and that was to just power my new MBP down.
So, I tried again, this time holding down Opt while turning my computer on so as to select a disk at boot. The same problem returned.
Just to check, I once again started up while holding down the Shift key to attempt a Safe Boot. No dice.
Prior to trying all of this I made sure that I did have the Apple Recovery Partition in addition to my user partion and the EFI partition, so I did not understand why this would be happening. Why could I not boot into Recovery? Why could I not select a boot disk? And, why could I not go into Safe Boot?
To be safe, I started up and logged into my MBP as I normally would, then set my startup disk to be my Recovery USB for OS X 10.8, restarted, and verified all three partitions (and, since I had my Time Machine disk connected all three times I forced the computer to power off, I verified it as well). I then set my startup disk back to my SSD, and logged in and got online to see if anyone else had experienced this issue. After making sure I was not being crazy and using key combinations that were somehow made irrelevant, I shut my MBP down and walked away for a few minutes.
The Solution
So what solved my problem? A good 'ol reset of the NVRAM (aka/fka PRAM). If you are not familiar with how to reset the NVRAM:
Power off your Mac and go do something else for 30 seconds to a minute.
Press and hold down the Opt, Cmd, P and R buttons, and then press the power button. I have big hands and this is a one person operation for me. If you are not so "lucky", find someone to press the power button as you hold those four buttons down.
Continue holding those four buttons down through the first startup chime and then release all four of them only after the second startup chime is sounded.
So, for some reason, I had to reset the NVRAM on a brand new MBP that had been started up only once and restarted only once when I enabled FV2. Maybe something cached needed to be cleared out following the FV2 process, or maybe something funky was carried over after it was setup in the factory and shipped direct to me from China.
The moral of the story is: If you have strage issues during the startup of your Mac, just reset the NVRAM and try again. This has worked for a number of strange issues on various Macs for me in the past and proved to be useful once again on a brand new MBP that I never would have thought needed its NVRAM reset so soon into its lifecycle.
Special Note
There are two processes I always complete and recommend to others following a major software update (e.g. upgrading to a new version of OS X) and when I restore or otherwise transfer the most recent Time Machine backup to my current Mac or to a new one.
First, following a major or massive software update, go into Disk Utility, select your system and data drive(s), and then just click on "Repair Permissions" (Choosing "Verify Pemissions" will result in having to then click "Repair Permissions" if any permissions need to be repaired, so remove one click from the process).
Second, after transferring from a Time Machine backup, I like to make sure that my user directory permissions are good to go before any time is allowed for problems with those permissions to set in. If you are not familiar with the user directory permissions and ACL repair process (this process is not the same as the "Repair Permission" functionality in Disk Utility), here is how to do it:
Shutdown your Mac and wait about 30 seconds.
Press and hold down Cmd-R and then power on your Mac. Once the Apple logo with the spinning wheel shows up, release those two keys.
From within the Recovery Console, open a new Terminal session via the "Utilities" menu.
Invoke the following command (all one word, lowercase): resetpassword
In the "Reset Password" application that opens, select the disk that your user home directory is on, and then click the "Reset" button at the bottom underneath the "Reset Home Folder Permissions and ACLs" heading and wait for the process to finish. Any messages displayed can typically be safely ignored. If you want to be sure, search for information regarding any messages that you do not like.
Restart your MBP and enjoy using it.
(Note that if you have FV2 enabled, you will need your FV2 Recovery Key to actually reset your password. This is one of many reasons that I enable FV2 - anyone can startup a Mac and go into the Recovery Partition if it exists and reset a password, but having to also enter the FV2 Recovery Key adds a nice extra layer of protection. In addition to that, setting a Firmware Password makes it nearly impossible to start up from any disk other that that which is currrenlty installed in your Mac without knowing the Firmware Password - another security bonus. If someone gets ahold of your Mac, and you have FV2 enabled and an appropriately complex Firmware Password set, then them using your Mac as their own becomes a decently difficult process. It's by no means perfect computer security, but it makes it more challenging for someone to steal and use your Mac.)
If anyone has any other tips to share or additional solutions to problem I described, please discuss and share.

Which OS X is installed on your Mac ?
Troubleshooting advice can depend on that information.

Is there any way to make a snow leopard partition on an early 2011 MacBook Pro that was upgraded to Lion, without the original boot disk?

So I have an early 2011 MacBook pro, I believe it shipped with snow leopard originally, as I purchased and upgraded to Lion fairly early on. I am trying to make a partition right now and have it run snow leopard so I can use programs that have PowerPC.
I should note, I replaced both the RAM and the harddrive in my Macbook pro. I changed from 4 GB of ram (that came shipped) to 8 GB of ram from a 3rd party, that I installed on my own months ago, have registered in the computer and have been working fine for quite some time now.
Also I should note I replaced my harddrive. I went from what ever the standard 500 GB harddrive that shipped with 15 inch early 2011 MB pro's. I now have a 3rd party SSD that's 240GB's that I also installed on my own, (at the same time as the RAM---Black friday items) The harddrive has been working just fine since then.
In installing the harddrive I borrowed a friends external harddrive and used a program called carbon copy cloner to get everything over to the SSD.
Now here is my issue. I have ordered the Snow Leopard (10.6.3) install disks from apple, I have created a partition on my SSD for snow leopard, but when I try to select the install disc for snow leopard at boot I get three beeps.
I know this issue has been posted elsewere but it said answered and the answer is no longer available. I also am unsure if any of the RAM or Harddrive swapping could have been causing the issue. I have the old harddrive and RAM still, but unfortunatley have no external harddrive anymore or money to afford one.
Is there any way I can install a partition that runs snow leopard on my early 2011 MB pro with what I have (new SSD, New RAM, Current version Lion running, no external drive, lack of original snow leopard disks [I lost them ] and the general 10.6.3 snow leopard boot disks).
Let me know If there is anything I can do. I'm a now broke college student so i'd like to spend as little $$$$ as possible
*PS I should also note the DVD drive is working fine, it reads the disk, the disk is brand new, it plays DVD's fine and has never had any issues in the years i've used it for similar tasks*
sorry for the long drawn out post, I just wanted to include as much as possible from what I've seen other people have issues with

BrettGoudy wrote:
...Is there any way I can install a partition that runs snow leopard on my early 2011 MB pro with what I have (new SSD, New RAM, Current version Lion running, no external drive, lack of original snow leopard disks [I lost them ] and the general 10.6.3 snow leopard boot disks)...
As the last post suggests, call Apple and order a replacement original disc for about $17. They will ask you the model and serial numbers.
Your retail version of Snow Leopard OS 10.6.3 will not work on that Mac as it requires a minimum of OS X 10.6.7 to boot and operate.
Another alternative is to again borrow another Mac to install your retail Snow Leopard into an external HD or partition, upgrade it to 10.6.8 and then clone it back to a partition on your MBP.

Unable to open windows using boot camp. Get message "The bless tool was unable to set the current boot disk." Any thoughts, Thank you.

Unable to open windows using boot camp. Get message "The bless tool was unable to set the current boot disk." I am using an Imac , Lion operating system, and Windows 7. It worked a few days ago. Any thoughts, Thank you.

Note that nowhere in the Boot Camp instructions does it tell you to use Disk Utility to format the Windows partition. The Boot Camp Assistant program creates the partition & sets the +partition scheme info+ of the disk as appropriate for the Windows installer but the Windows installer itself is responsible for formatting the new partition with the appropriate +file system scheme+ (NTFS for Windows 7).
If you follow the instructions in the Boot Camp Installation & Setup Guide to the letter you should have no problems installing Windows.

BC 2.1 vs 2.0, graphics, boot disk

Similar Messages

Maybe you are looking for