BCS AVC Warning Msg

Our system is configured to issue warning messages when the 80% and 90% budget consumption level is reached. The problem is that both percentages use the same message number FMAVC006.
Is it possible for each consumption level to use its own unique message number and message? Where is this set up in the system? Any ideas?

Hi,
You can set 'Information' message to 80%, of course, but I'm not sure that there is a possibility to arrange separate message for every profile. Maybe, there is something in new release, but I cannot remmember reading things like this.
Regards,
Eli

Similar Messages

Sales order- Warning msg Static credit check

Hi, SAP Guru,
When I create a order & saving it ...a POP UP comes with warning msg the static credit limit exceeds..... Can any one please let me know the how I can remove the warning POP UP . As client do not want any pop up should come while saving the order.
Please help.
Thx & regards

Hi,
If you remove the entry from the field "Check credit" in "OVAK" T.Code,the credit check will not happen for this order type.Which we don't want.
We need that the credit check should happen but the pop-up is to be removed.right?
For this goto the T.Code "OVA8".
Select your valid entry.Details.
Remove the value as "blank" for the field "Reaction".Press F4 for more options.
Beside this there is one more field "status/block" which is ticked means the order will be blocked for further transactions.And also status will be updated accordingly.
These blocked order have to be released either by using the T.Code "VKM3/VKM1".
Regards,
Krishna.

WARNING MSG

had my iphone with me out by the pool... it was on the side face down exposed to the sun... warning msg came up with a yellow triangle with an ! in the middle and the word temperature above it... seems to be working fine now... but was playing my ipod at the time and it just stopped playing...

If the phone gets too hot, it will shut itself down. See p. 132 of the manual... http://manuals.info.apple.com/enUS/iPhone_UserGuide.pdf

Ho do we make msg. CK666 become warning msg when we do costing run?

Dear Experts,
The sys. activate transfer price for preserve use.
When we do costing run for profit center valuation, the following error msg ocurred.
CK666 Material 227BO0001/plant 1030: Transfer price could not be found.
Diagnosis
When switching profit center 0000008000->0000005000 (from the material component to the costing object), a transfer price could not be determined for transfer price variant 0 in respect of material 227BO0001 in plant 1030.
System Response
If you carry out costing for a profit center valuation, material 227BO0001 goes into the cost estimate without a value.
If you create a cost estimate for group valuation, profit from material 227BO0001 is not transferred into the cost component split.
Procedure
Check the settings for transfer price variant 0.
In OKEQ, the variant for TP is blank.
Ho do we make msg. CK666 become warning msg when we do costing run? and let costing result can be release, or there's another way?
Thanks in advance.

There is alternative solution.
Try using TCode SE91.
Enter the class - CK and Enter the message number 666.
Select that line message line.
Go to Utilities, Click on "Where-Used-list" or press "CtrlShiftF3" from keyboard.
Select programs and deselect all others.
Identify your program and double click against that under short description.
There you can change the letter from "E" to "W" as your requirement.
NOTE: take assistance of ABAPer of this, Do enquire about the implication of the same in sandbox before doing anything on any other client.
Thanks & Regards
JP

Where warning msg & error msg are maintained in SPRO

Dear All,
pl give the menu path to know that Where warning msg & error msg are maintained in SPRO.
regards
sap11

Hi,
In case of Purchasing, the path to maintain warning & error messages is:
Material Management->Purchasing->Environment Data->Define Attributes of System Messages
In case of Inventory Management,
Material Management->Inventory Management and Physical Inventory->Define Attributes of System Messages
In case of External Service Management,
Material Management->External Services Management->Define Attributes of System Messages
In case of Logistics Invoice verification,
Material Management->Invoice Verification->Logistics Invoice Verification->Define Attributes of System Messages
In case of Material Master,
Logistics - General->Material Master->Basic Settings->Define Attributes of System Messages
Then, for eash message no., Maintain whether the message is to be shown as warning or error or information message.
Reward if useful.
Thanks & Regards,
Komal

Supress warning msg during RRI

We have a query that jumps to R/3 tcode. when we try to jump, for some document no's the jump goes smooth .. for some other doc's, it throws a warning msg saying that the infosource is not linked to the source system. this happnes with some of the docs only. But the jump does go thru to R/3.
I want to supress the warning msg during the jump. I tried in RSRT, but it doesnt help. the error code i get is RSBBS206. where do i have to exactly supress this warning?
Any pointers or clues would be appreciated.
thanks,
Voodi

Hi Vodi,
In RSBBS, go to the sender query in change mode. There should be a tab in the middle column where you have to give your infosource name..
For. eg If you want to jump from Cost centre report (BW) to Masterdata transaction in R/3, you ust assign this particular infosource in RSBBS settings..
Hope it helps.

Warning msg "Signal is not contiguous"

Hi,
I used NI FGen to generate a sine wave to pump into a circuit (under test) and use NI Hi-speed Digitizer to capture the output of the circuit.
The captured signal goes through a low pass filter. This warning message appear at the filter when it is Run continuously.
'Run Once' does not have problem.
Has this got to do with synchronizing the 2 modules in the PXI system or is it a matter of wrong sample rates.
I have searched Help and it mentioned using TClk to synchronize the 2 modules.
How do you use TClk in Signal Express?
How to solve this warning msg?
Someone please help.....thanks.
Regards,
SeeMist

Hello,
I am glad to hear that you resolved the warning issue. In regard to the other project, are you just interesting in generating the signal once? What is the lay out of the steps in the project for both the FGEN and SCOPE? Is the FGEN set to finite or continous generation mode? How is the SCOPE step setup in the Execution Control tab?
SeeMist wrote:
Currently (another project) I use the NI-FEN step to generate a signal from a .hws file (a 25khz burst signal).
It works fine by itself and the "Scope Soft Front Panel" (SFP) is always good at capturing the generated signal.
(The output of generator is externally connected to the input of the Scope).
However, after I closed the SFP and inserted NI-Scope Acquire step in Signal Express, I was not always successful in capturing the signal generated. Sometimes okay, sometimes not.
The error occurred at the FGen step : "Finite Generation timeout"
Do I have to initialise or there is a problem with my setting? Trigger or synchronization problem?
The setting of the FGen remains the same in both tests.
The NI-Scope: Trigger = Edge ; Sample rate =100MS/s; Record Length =5000
Samantha
National Instruments
Applications Engineer

Warning msg at the time of PR creation

When I am creating the PR a Warning msg is being displayed as:-
"Base unit of measure KG adopted from material master record"
Could anybody suggest me, why this msg is comming.
and if I ignore it and go ahead with pressing enter, Is there any future impact by the same.

Hi There
When you create the PR, if you have not provide the unit of entry, System will read the master data and bring the base unit of measure,, and provide the warning message,, You can acknowledge that message and proceed further it is not an issue,,
For more details ref the below link, it provides the details of diff units and usages,,
http://help.sap.com/saphelp_46c/helpdata/en/a5/63310c43a211d189410000e829fbbd/content.htm
Thanks
Senthil

Warning msg. when trying to activate MP

guys,
I am trying to activate MP, and i am getting following Waring msg. ! what does it mean ? and how serious it it ?
"The InfoProvider properties for ZCIA_M05 are not the same as the system default
Message no. BRAIN376"
thanks

yes i did assign all the infoobject. i could activate it too, but before i could activate it, i got a warning msg.
still, i ignore those and activate it.
but i wasnt sure i serious it. Also i checked MP's properties and its all the same( like other MPs).
But, i thought let me get some information from Experts about that worning !!!
let me know if you have any idea about it.
Also, When i was trying to Activate MP again, it was asking like " its already active, do u still want to active" and if i say yes, it
gives me an error msg. " MP is not yet Locked"
Do i need to Lock it ????? what is that ??
thanks

Warning Msg - While checking Mulitproviders

Hi Frds,
When i am trying the check the mulitproviders, we are getting warning msg. Below is the warning msg which we getting.
Error messages from point of view of OLAP processor:
Message no. R7I127
Now we have upgrade our patch level from 16 to 21.
Kindly can anyone give me some solution to overcome these warning msg.
Thanks
Yuvi

Has the MultiProvider ever been activated in the past? If you activate it, and it hasn't been activated previously, you'll get this message from time-to-time (another one of those "undocumented features"). After actiavting it, go back into the MultiProvider in edit mode and run a check on it. It shouldn't throw that warning anymore.

WARNING MSG . DURING J1IEX

Dear All ,
user had created a Stock transfer P.o , in this P.o there in no tab of invoice , now it's Goods rcvd is done here all excise details are maintained , here exscise base value is visible for all line items . now user had to post J1IEX so as he clicks on simulate a warning msg comes that is -" PLEASE CHECK EXCISE BASE FOR ITEM IS ZERO ! ".
Pl help what to do .
sap11

Thanks guys, I figured it out.
Message was edited by:
voodi

Warning Msg during RRI

When I'm trying to jump from a source report to target query via RRI, i get a warning msg (thought the query runs). I want to supress the msg.
I tried supressing the msg in source query, target query and both of them together. Still the msg is being displayed. Where do I need to supress the msg if its during RRI process?
The variable and the hierarchies being used for cost center is the same in both the queries. Any thoughts?
Error msg:
Invalid filter on 0COSTCENTER: Filter changed
    Message no. BRAIN502
Diagnosis
    You tried to filter on a characteristic with active presentation
    hierarchy by a node of another hierarchy.
    This can only be done by switching the hierarhcy or for example by using
    the report/report interface.
System Response
    The filter is not evaluated for the characteristic, but removed instead.
Procedure
Procedure for System Administration

Thanks guys, I figured it out.
Message was edited by:
        voodi

Report to Report Interface warning msg

Hi,
I am getting "Incompatible for target selection for fiscal year" warning msg in SAP BEX.I am using same variable in my source and target system to select fiscal year.
How to supress this warning message?
thanks
venkii

If your report is working fine as per expectation in RRI, and your requirement is to supress the warning message, you can set the global setting of the workbook to supress any warning messages.
Question:
Do you have any customer exit on this variable?
- Danny

In Windows 7 warning msg says another version of Adobe CC installer is running while updating LR 5 to 6

In Windows 7 warning msg says another version of Adobe CC installer is running while trying to update LR 5 to LR 6.

Hi There,
Kindly restart the machine and try to initiate the installation again.
Download Lightroom 6: Digital photography software | Download free Adobe Photoshop Lightroom CC trial
Serialize Lightroom CC trial to activate as Lightroom 6:https://helpx.adobe.com/lightroom/kb/serialize-lightroom-cc-trial-to-activate-as-lightroom -6.html
Thanks,
Atul Saini

Transport datasource 0FI_AP_4 on R3 gets warning msg

RSA6 on R3 and select the datasource 0FI_AP_4, click the truck picture icon which is "Transport datasource", get a warning msg:
"Warnings have occurred (see log)", click the question mark for log, but still get the same short msg. What could be the reason?
The reason why we are doing this is that we found a new field added to the structure and correspondingly the datasource fails to show up in the target system after transported.
Thanks

Hi,
If your ES in DEV has more filed than ES of QA/PROD , then yiou need to release and import the transport request of that change to ES.
Without tranporting the change to ES first ,you are trying to transport the request of DS(which internally depends upon the ES) ,so you are getting warning.
With rgds,
Anil Kumar Sharma .P

BCS AVC Warning Msg

Similar Messages

Maybe you are looking for