Beamforming troubleshooting on AIR AP1142
Hello!
I set up beamforming (ClientLink) at both frequencies 2.4GHz and 5GHz on AIR-AP1142N-R-K9:
AP#sh vers
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 15.2(2)JA, RELEASE SOFTWARE (fc1)
AP#sh run int dot11Radio 0
interface Dot11Radio0
beamform ofdm
AP#sh run int dot11Radio 1
interface Dot11Radio1
beamform ofdm
AP#sh controllers dot11Radio 0 | i Beam
Hardware Beamforming: Configured Yes, Active Yes, RSSI Threshold -50 dBm
AP#sh controllers dot11Radio 1 | i Beam
Hardware Beamforming: Configured Yes, Active Yes, RSSI Threshold -60 dBm
All clients are connected to wifi on 2.4GHz on Dot11Radio0:
AP#sh dot11 associations
802.11 Client Stations on Dot11Radio0:
SSID [UE-WiFi] :
MAC Address IP address Device Name Parent State
1111.1111.1111 10.255.0.35 unknown - self Assoc
2222.2222.2222 10.255.0.34 unknown - self Assoc
3333.3333.3333 10.255.0.36 unknown - self Assoc
SSID [WiFi-UE-Group] :
MAC Address IP address Device Name Parent State
4444.4444.4444 10.10.30.71 ccx-client - self EAP-Assoc
SSID [WiFi-UE-Printers] :
MAC Address IP address Device Name Parent State
5555.5555.5555 10.10.30.77 ccx-client - self Assoc
6666.6666.6666 10.10.30.75 ccx-client - self Assoc
7777.7777.7777 10.10.30.70 ccx-client - self Assoc
AP#sh dot11 associations all-client
Address : 1111.1111.1111 Name : NONE
CCX Version : NONE Client MFP : Off
Key Mgmt type : WPAv2 PSK Encryption : AES-CCMP
Current Rate : m5-2 Capability : WMM ShortHdr ShortSlot
Supported Rates : 1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0-2 m1-2 m2-2 m3-2 m4-2 m5-2 m6-2 m7-2
Voice Rates : disabled Bandwidth : 20 MHz
Signal Strength : -77 dBm Connected for : 3835 seconds
Signal to Noise : 18 dB Activity Timeout : 60 seconds
Address : 2222.2222.2222 Name : NONE
CCX Version : NONE Client MFP : Off
Key Mgmt type : WPAv2 PSK Encryption : AES-CCMP
Current Rate : m5-2 Capability : WMM ShortHdr ShortSlot
Supported Rates : 1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0-2 m1-2 m2-2 m3-2 m4-2 m5-2 m6-2 m7-2
Voice Rates : disabled Bandwidth : 20 MHz
Signal Strength : -59 dBm Connected for : 3475 seconds
Signal to Noise : 37 dB Activity Timeout : 60 seconds
Address : 3333.3333.3333 Name : NONE
CCX Version : NONE Client MFP : Off
Key Mgmt type : WPAv2 PSK Encryption : AES-CCMP
Current Rate : m7-2 Capability : WMM ShortHdr ShortSlot
Supported Rates : 1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0-2 m1-2 m2-2 m3-2 m4-2 m5-2 m6-2 m7-2
Voice Rates : disabled Bandwidth : 20 MHz
Signal Strength : -56 dBm Connected for : 2681 seconds
Signal to Noise : 31 dB Activity Timeout : 56 seconds
Address : 4444.4444.4444 Name : NONE
CCX Version : 4 Client MFP : Off
Key Mgmt type : WPAv2 Encryption : AES-CCMP
Current Rate : 54.0 Capability : WMM ShortHdr ShortSlot
Supported Rates : 1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
Voice Rates : disabled Bandwidth : 20 MHz
Signal Strength : -57 dBm Connected for : 3647 seconds
Signal to Noise : 33 dB Activity Timeout : 18 seconds
Address : 5555.5555.5555 Name : NONE
CCX Version : 4 Client MFP : Off
Key Mgmt type : WPAv2 PSK Encryption : TKIP
Current Rate : 48.0 Capability : WMM ShortHdr ShortSlot 11h
Supported Rates : 1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
Voice Rates : disabled Bandwidth : 20 MHz
Signal Strength : -51 dBm Connected for : 5973 seconds
Signal to Noise : 35 dB Activity Timeout : 274 seconds
Address : 6666.6666.6666 Name : NONE
CCX Version : 4 Client MFP : Off
Key Mgmt type : WPAv2 PSK Encryption : AES-CCMP
Current Rate : 54.0 Capability : WMM ShortHdr ShortSlot 11h
Supported Rates : 1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
Voice Rates : disabled Bandwidth : 20 MHz
Signal Strength : -52 dBm Connected for : 3090 seconds
Signal to Noise : 44 dB Activity Timeout : 308 seconds
Address : 7777.7777.7777 Name : NONE
CCX Version : 4 Client MFP : Off
Key Mgmt type : WPAv2 PSK Encryption : AES-CCMP
Current Rate : 54.0 Capability : WMM ShortHdr ShortSlot 11h
Supported Rates : 1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
Voice Rates : disabled Bandwidth : 20 MHz
Signal Strength : -64 dBm Connected for : 75 seconds
Signal to Noise : 30 dB Activity Timeout : 328 seconds
All clients have a low Signal Strength (below RSSI Threshold -50 dBm), but only clients with MAC 4444.4444.4444 and 7777.7777.7777 is involved by ClientLink. Why?
AP#sh int dot11Radio 0 lbf rbf
RBF Table:
Index Client MAC Reserved Valid Tx BF Aging Locked
1 4444.4444.4444 Yes Yes Yes No No
2 7777.7777.7777 Yes Yes Yes No No
Vlad,
According to this article (http://www.revolutionwifi.net/2010/07/beamforming-clientlink-and.html), maximum number of Beamforming-clients = 15:
"...Cisco's documentation states that a maximum of 15 clients per radio can be supported using ClientLink at the same time..."
...and I saw, on other access point AIR-AP1142N-R-K9 there were at the same time 6 clients at one frequency (2.4GHz).
I have an assumption that ClientLink doesn't service the client, at which "Current Rate: 54.0" (without beamforming), irrespective of values "Signal Strength: ... ". In my case with client 5555.5555.5555 situation disputable as it is on boundary - 51Bdm, though "Current Rate : 48.0".
Here the white paper on ClientLink 1.0 / 2.0 / 3.0 technologies:
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps11983/at_a_glance_c45-691984.pdf
Similar Messages
-
Graphics troubleshooting Macbook Air
To whomever can tell me what I need to do to fix the following problem I am having: My screen occasionally to almost constantly - turns gray (so that I can still barely see what is on the monitor) and a solid black line @ 2 inches in width or streaks of black appear along with this at the same time. I am unsure what to do, I have read a good bit on graphics display in Macbook Air 13-inch, Mid 2011, but I am unsure exactly how to fix my problem. Any help, advice, or guidance will be much appreciated!
Computer Specifications are below:
I have a Macbook Air 13-inch, Mid 2011 with
Processor 1.7 GHz Intel Core i5
Memory 4 GB 1333 MHz DDR3
Software OS X 10.9.4 - Mavericks
Graphics Intel HD Graphics 3000 384 MB
Chipset Model: Intel HD Graphics 3000
Type: GPU
Bus: Built-In
VRAM (Total): 384 MB
VRAM (Dynamic, Max): 10
Vendor: Intel (0x8086)
Device ID: 0x0116
Revision ID: 0x0009
Displays:
Color LCD:
Display Type: LCD
Resolution: 1440 x 900
Pixel Depth: 32-Bit Color (ARGB8888)
Main Display: Yes
Mirror: Off
Online: Yes
Built-In: Yes
Thank You!
Beth JohnsonPlease make a Genius Appointment and take it in for service. We can't fix a hardware problem.
-
Just out of the box. Configured IP address, security and enabled the radios. When I checked the gigabit interface it shows:
Software status -- Enabled
Hardware status -- Down
Is this an indication that the AP has a hardware problem and I can send it for RMA?Hi mcaoile,
As Leo suggested, could you please paste the full output?
thanks,
Vinay -
Installing a second AIR-AP1142-AK9 in same office building
What should I be aware of? Any issues?
We should be careful while seeing that the channels are not-overlapping. Get Spatial Spatial multiplexing is a multiple antenna technique that increases the data rate as compared to single antenna techniques. Theoretically, spatial multiplexing can increase the capacity of the system as pairs of transmitter and receiver antennas are added to the system. The source data (usually data requested by the user) is split into two or more independent data streams that are transmitted over multiple antennas, called spatial streams. A common configuration is the previously mentioned 2×2 MIMO system. In this case the throughput is theoretically doubled compared to the single antenna configuration. There are some assumptions about the channel correlation conditions and necessary signal-to-noise ratio (SNR) required to approach this increase in throughput, but these topics are best left for another day.
Hello Abhishek,
Exactly WHAT are you takling about?????
Could you elaborate what you mean by this? -
I can't install ANY AIR-based App in Windows XP Pro SP3
Here is the problem: I have AIR 1.5.1.8210, but any AIR apps can't be installed and when I try it the OS crashes and I have my computer restarted. It's very weird 'cause it's heppen only with AIR apps.
Yes, this is my last resource to find an answer to it.
Yes, I've done my homework and yes, I've done some research (and still doing it)
Yes, I'm using my administrator account logged on with password (so, I think, apps has no problem to install)
Yes, I tried install it with another user account I thought the app will ask the admin password (just like in Linux OS, when the app on installation ask you about the root password). Even though, no success. Of course, it's something expected 'cause the user hasn't admin permissions. But I give a shot.
Yes, I've already installed/installed about 5 times AIR runtime and the AIR apps (even manually) and no success...at all!
Yes, I used at least 4 apps to system/registry/file cleaning (CCleaner, Glary Utilities, Advanced System Care and MVRegClean)...too many of them, but only to be sure of the complete cleaning.
Here in the forum another person, but on Vista, found almost the same problem as I, here's the link: http://forums.adobe.com/thread/199842?tstart=30
And another buddy ask about admin rights to install AIR apps, here's the link: http://forums.adobe.com/thread/415756?tstart=30
And, I found two others infos in Adobe site per se about any troubleshooting on AIR: http://kb.adobe.com/selfservice/viewContent.do?externalId=kb403150&sliceId=1 and log actions during installation: http://kb.adobe.com/selfservice/viewContent.do?externalId=kb403123&sliceId=1.
2+2 = 4. So, I done/undone all the steps in the last two links (I installed/unistalled the AIR runtime and AIR apps 5 times, remember?) Usually, I can handle my own problems in computer, but this one I can't figure it out.
After all of this here's my system specifications: AMD Athlon 64 X2 Dual Core 3600+ (2.01Ghz), Windows XP Pro SP3 (32bits), Nvidia GeForce 7100 (512 Mb), 1.5 Gb RAM. Web browser: Mozilla Firefox 3.0.8 with TwitterFox.
So, could anyone help? I know, I know to mucj information, burt it was to facilitate the conversation, believe me.
Kisses, Cat777.Well, well, well, right before somenone could answer me. I found the answer just here in the forum. I really love it!!!
Seems to be a incompatibility with the file created on Folder Lock installation: "windrvnt.sys." In this case, it is just uninstall Folder Lock and tah dah! Everything works perfectly.
Here comes my request: Hey, developers you all could give a try in resolve this issue, huh? At least give a try...It'll be very nice have the two programs properly installed in anybody's (who wants it) system.
Thanks, anyway for this space to research, change some infos even undirectly. If it was not this forum and all the debate in here maybe I'll be in the dark search for the resolution of it.
Thanks. -
Hello Folks,
I have installed CS6 and selected Adobe Support Center from the help menu. I keep getting the following error message.
"The installation of this application is damaged. Try to re-install the application or contact the publisher"
I tried re-installing CS6 but am still getting the same error message, with a bouncing Adobe Air icon in my dock.
Any suggestions to remedy this issue would be appreciated.
JimHello! here is a document about troubleshooting Adobe Air installations: http://helpx.adobe.com/air/kb/troubleshoot-air-installation-windows.html
-
HT3275 Time Machine Repeated verification failures?
We have an Imac and a MacBook Air and run time machinr on both to a WD MyBookLive connected over the WiFi. It appears to work fine in the iMac but the MacBook Air keeps coming up with the message Time Machine completed a verification of your backups. To improve reliability, Time Machine must create a new backup for you. It has been happening every two or three weeks but last time it created a new backup ti came up with this massage only the next day. If it won't work properly I am going to have to ditch time machine and copy key files manually.
Any Suggestions?There is some info here.
http://pondini.org/TM/D3.html
But go back and read through the whole troubleshooting.
Air in particular seem to often have issues.
I would be incline to buy the USB to Ethernet (or even thunderbolt to ethernet) adapter and use wired connection to do it. -
The speakers on my macbook air isn't working. How do I troubleshoot?
The internal speakers on my macbook air isnt working. I have turned the volume up muted un muted and the I still cannot hear anything. How do I troubleshoot? Any help would be appreciated. Thank you!
Goto... System Preferences > Sound
-
Troubleshoot issues with Telstra Air
Check whether Telstra Air® has been activated on your home broadband service
Check your activation status in My Account or through the Telstra 24x7® App.
In My Account, go to the Internet section and scroll to Telstra Air. Your status will be listed as either active or inactive.
In Telstra 24x7, go to the main menu and select Telstra Air. This will display a page showing your Telstra Air details from My Account, including your activation status. If Telstra Air does not appear in the main menu, you may not be eligible for the service and should visit us in store or contact us via 24x7 Chat for further assistance.
What to do if the login page doesn’t open automatically
If your browser doesn’t automatically open the login page when you first connect to the Telstra Air Network™:
Make sure your device is connected to the Telstra Air Wi-Fi network
Open an internet browser – like Internet Explorer, Google Chrome or Safari.
Your internet browser will load up the login page
Enter your Telstra ID username and password on the login page to start accessing Telstra Air.
Network speeds on the Telstra Air Network
Speeds may vary depending on how close you are to our hotspots, the number of other users connected to the same hotspot and the device you are using.Re: Troubleshoot issues with Telstra Air
My Telstra Air was activated yesterday, downloaded App, logged in using my bigpond username/password, Status: Not Connected, Hotspots: Not Available. Find Hotspots: shows up on map OK.
Phone (Android) shows Free_Telstra_WiFi: Not in range when the modem is in the same room??? -
MacBook Air Flashing Question ? Mark Folder - Troubleshooting Help!
I am trying to figure out a problem for a friend's Macbook Air. Not sure on the year it was manufactured, but it doesn't look to be but 2 or 3 years old. I have no clue what operating system she was running.
The problem she is having is the flashing question mark folder. I have tried doing a safe boot, but when I hold down shift after powering it off and back on nothing happens. I have tried doing a PRAM reset, it chimes 3 times then goes back to the flashing question mark folder.
The furthest I have gotten is holding down "alt/command" to see if the system preferences would pop up. But all I get is the option to select a wifi network. So that's something! Does anyone have an idea on how to solve this issue? I would like to have a bit more knowledge before I take it to the apple store. Has anyone ran into it asking for a wifi network instead of being able to boot it? Please advise. Thanks!On the bottom of the MBA should be a serial number. Enter it here and post back the model/year information:
https://selfsolve.apple.com/agreementWarrantyDynamic.do
Ciao. -
Troubleshooting Logic and I/O board on A1370 11" MB Air after wine spill
OK,
My wife spilled about 1/4 cup of wine on the keyboard of her MacBook Air. This is an A1370 (EMC 2471) 11" (Core i5 Mid 2011) model.
I have read the articles in this forum and others on what to do when you spill on one of these computers.
What I would like from this forrum is guidance/help/suggestions/best-guess on determining what I need to replace.
Here are the details.
Directly after the spill, she tells me that the computer turned itself off, and would not come back on - no lights, no start chime, nothing.
I immediately took the back off the computer and mopped up what I could without completely dissasembling the system because it was late at night.
The next morning, one of the kids tried to start the computer (ya, I know that's bad and don't know why the **** he did it but he did). He "fessed up" later and said that when he pressed the power button the keyboard lights came on and chimed then went off and that was it.
I proceeded to take apart the computer, removing the battery, logic board, I/O board, airport, HD, etc.
I noticed that there was wine stain on the logic board and the I/O board and other areas and cleaned it all up with isopropyl and Q-tips.
I then gave the logic board and I/O board a very thorough wash with a cleaning spray by MG Chemicals called "Safety Wash II". Basically alcahol.
I scrubbed the two boards thoroughly with a soft bristle brush for about an hour, then I soaked the entire board in isoproyl alcohol bath for 2 hours then sprayed and scurbbed again until I felt that I got all the wine off.
I did notice a small amount of "purble" on two of the tiny contacts for the LCD connection on the logic board but could not remove no matter how much scribbing I did. The two contacts were number 3,4 if you are counting from right-to-left when viewing the logic board from the bottom of the PC, with the fan to the right.
After a good dry with a hair dryer and letting it sit a few more hours I put it all back together, crossed my fingers, plugged in AC and pushed the power button -- nothing happened.
I had an orange light on AC adapter so I let it charge over night. The next day the AC light was green and the backlight on the keyboard was lit. Tried starting and still nothing.
I took the back off again and disconnected the battery then plugged in the AC adapter. At that point the fan started spinning and I got the start "chime" but nothing on the LCD.
I disconnected AC and plugged in battery and noticed the same thing.
Now whenever I disconnect AC chord and reconnect it I get the chime with fan starting but nothing more.
Also, the backlight on the keyboard stays on all the time and the fan runs all the time if the batter or the AC is connected.
So, I am wondering what I need to replace?
logic board?
I/O board?
keyboard?
all of the above?
Would appreciate guidance.Zane is right, ....I used to repair laptops for years as well,.....diagnosing such things is FUTILE.
Lucky you there are are almost no parts IN the macbook Air. Its IO and Logic and thats really almost it.
Contact Apple for in shop full diagnosis and parts replacement,......youre not going to "diagnosis" nor "fix" it after a spill (without parts replacement) by any means.
Even if you had a BEST CASE spill.....corrosion and failure would ensue on average 7 to 20 days.......then kaput.
Spills turn the best computer repair person into what looks like (to the customer) dufus......WHY? ......because its a "spin the wheel and GUESS where ALL the liquid went"
replace A......works ok for a week.....whoops, ..........oh yeah, theres a couple drops under under a solder connection on part B........replace that.... -
ITunes/Music Home sharing does not work on my iPad Air
No matter what I do I cannot use Music.app on my iPad Air to play music from my iTunes Library with Home-Sharing switched on. The Library name correctly appears in the Music.app source list after the loading symbol takes an age to complete. When it appears to have connected to the Library on my Mac, contents of my Library are shown in the app but I cannot play anything. If I select an albumn and press Play the Music.app merely cycles rapidly through all the track titles of the Album and then stops. Nothing plays. I've tried dozens of times to get this to work, even rebuilding my iTunes Library. Nothing seems to cure the problem. I can connect and play via Plex which is just plain daft seeing Apple designed all the software/hardware but they, themselves, cannot correctly code for this basic functionality.
Also, not all Album cover artwork is displayed correctly.
It seems many of the things I bought the iPad for are non-functional and the tablet is virtually useless. I can't beleive Apple would produce software and hardware which is specifically made to work harmoniously but obviously doesn't.
Any help, here, please?
I'm also having problems with Bluetooth connecting to my Mac Pro (2008)... Namly, it will not.Understanding Home Sharing
http://support.apple.com/kb/ht3819
Setup Home Sharing on iPad
http://support.apple.com/kb/ht4557
Troubleshooting Home Sharing
http://support.apple.com/kb/TS2972 -
Movies from iMac 27 do not show up on macbook air
I have 24 home-made movie that show up on my main computer, iMac 27, two iPads and and iPhone5. However, I am baffled how to get the same movies to show up on my Macbook Air. I've tried Sharing the Library, turning Sharing off and on on both compueters, and many other obvious possibilities. This is baffling me. Has anyone else had the same situation and a solution to go with it?
Thank you,
Steve RoeslerHello, Steve.
Thank you for visiting Apple Support Communities.
I would need a little more information on this issue to provide a better answer. Are these movies in your iTunes library? If not see the steps in the first article below. Some imported movies do show as Home Videos when imported. If these are in your iTunes library, see the troubleshooting steps in the second article below.
Adding music and other content to iTunes
http://support.apple.com/kb/ht1473
Troubleshooting Home Sharing
http://support.apple.com/kb/ts2972
Cheers,
Jason H. -
Config air-lap1041n-e-k9 with cisco 5500 (5508) series wireless controller. how to?
Hi!
I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
Log from AP:
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x00000184
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialize
PCIEx: initialization done
flashfs[0]: 6 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 2369024
flashfs[0]: Bytes available: 30016000
flashfs[0]: flashfs fsck took 21 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 44:2b:03:dc:09:25
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 2369024
flashfs[1]: Bytes available: 29757952
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1041N-E-K9 (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FCZ1611W414
PowerPC405ex CPU at 333Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 7.0.94.21
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:2B:03:DC:09:25
Part Number : 73-14034-04
PCA Assembly Number : 800-34273-05
PCA Revision Number : A0
PCB Serial Number : FOC16075VZ3
Top Assembly Part Number : 800-34284-03
Top Assembly Serial Number : FCZ1611W414
Top Revision Number : A0
Product/Model Number : AIR-LAP1041N-E-K9
% Please define a domain-name first.
Press RETURN to get started!
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:09.574: *** CRASH_LOG = YES
Base Ethernet MAC address: 44:2B:03:DC:09:25
*Mar 1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
(contains, 1024 messages)
*Mar 1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:11.892: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
*Mar 1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
logging facility kern
^
% Invalid input detected at '^' marker.
*Mar 1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
*Mar 1 00:09:08.282: -Verify the required power-injector is installed on this
port: AIR-CT5508-K9(Gig 0/0/2).
*Mar 1 00:09:08.282: -If a power-injector is installed, issue the command:"pow
er inline negotiation injector installed"
*Mar 1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
static IP. Forcing AP to use DHCP.
*Mar 1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
Not in Bound state.
*Mar 1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
. Renewing DHCP IP.
logs from wireless controller:
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Gu
est
ap-manager 2 untagged 209.165.200.231 Dynamic Yes No
management 1 untagged 209.165.200.230 Static Yes No
service-port N/A N/A 192.168.1.157 Static No No
virtual N/A N/A 1.1.1.1 Static No No
(Cisco Controller) >
i conect with service-port ok and the management port works, i think.
AP442b.03dc.0925>ping 209.165.200.230
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
AP442b.03dc.0925>
Help, please!
i write in spanish:
Hola:
Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, GraciasHi!
I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
Before the logs, I see this message from AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Hola:
He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Un saludo
Antonio R.
(Cisco Controller) >show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: AIR-CT5508-K9, VID: V02, SN: FCW1608L05X
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 17 mins 45 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Network Information
RF-Network Name............................. hosp
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Location
Site Name........................................ default-group
Site Description.................................
WLAN ID Interface Network Admission Control
1 management Disabled
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority GroupName
Press Enter to continue or to abort
AP Config
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Airewave Director Configuration
Press Enter to continue or to abort
802.11a Configuration
802.11a Network.................................. Disabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Video AC:
Video AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Press Enter to continue or to abort
802.11a Advanced Configuration
Press Enter to continue or to abort
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
802.11a AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
--More or (q)uit current module or to abort
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n Channel Width...................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
Radio RF Grouping
802.11a Group Mode............................. AUTO
--More or (q)uit current module or to abort
802.11a Group Update Interval.................. 600 seconds
802.11a Group Leader........................... c4:64:13:8f:93:40
802.11a Group Member......................... c4:64:13:8f:93:40
802.11a Last Run............................... 75 seconds ago
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
--More or (q)uit current module or to abort
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
--More or (q)uit current module or to abort
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Enabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ 50
Video reserved roaming bandwidth.............. 0
802.11b Advanced Configuration
Press Enter to continue or to abort
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,6,11
Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
Radio RF Grouping
802.11b Group Mode............................. AUTO
802.11b Group Update Interval.................. 600 seconds
802.11b Group Leader........................... c4:64:13:8f:93:40
802.11b Group Member......................... c4:64:13:8f:93:40
802.11b Last Run............................... 213 seconds ago
Mobility Configuration
Symmetric Mobility Tunneling (current) .......... Enabled
Symmetric Mobility Tunneling (after reboot) ..... Enabled
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... hosp
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x97e2
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast
IP Status
c4:64:13:8f:93:40 209.165.200.230 hosp 0.0.0.0
Up
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 0
Probe request rate-limiting interval............. 500 msec
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
dot11-padding.................................... Disabled
Authentication Response Timeout (seconds)........ 10
Rogue Entry Timeout (seconds).................... 1200
AP Heart Beat Timeout (seconds).................. 30
AP Discovery Timeout (seconds)................... 10
AP Local mode Fast Heartbeat (seconds)........... disable
AP Hreap mode Fast Heartbeat (seconds)........... disable
AP Primary Discovery Timeout (seconds)........... 120
AP Primed Join Timeout (seconds)................. 0
Packet Forwarding watchdog timer (seconds)....... 240 (enable)
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility.................................... Oui:00:14:7e : Vendor:pango S
tate:Disabled
Interface Configuration
Interface Name................................... management
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 209.165.200.230
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 209.165.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 192.168.1.1
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 209.165.200.230
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
Interface Name................................... service-port
MAC Address...................................... c4:64:13:8f:93:41
IP Address....................................... 192.168.1.157
IP Netmask....................................... 255.255.255.0
DHCP Option 82................................... Disabled
DHCP Protocol.................................... Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... virtual
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 1.1.1.1
DHCP Option 82................................... Disabled
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... HOSP3C
Network Name (SSID).............................. HOSP3C
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
WLAN ACL......................................... unconfigured
DHCP Server...................................... 209.165.200.230
DHCP Address Assignment Required................. Enabled
Quality of Service............................... Platinum (voice)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT(802.11r)............................. Disabled
FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout......................... 20
FT Over-The-Air mode............................. Enabled
FT Over-The-Ds mode.............................. Enabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Infrastructure MFP protection................. Enabled
Client MFP.................................... Optional
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Enabled
Load Balancing................................... Enabled
Mobility Anchor List
WLAN ID IP Address Status
Press Enter to continue or to abort
Press Enter to continue or to abort
ACL Configuration
Press Enter to continue or to abort
CPU ACL Configuration
CPU Acl Name................................ NOT CONFIGURED
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
RADIUS Configuration
Vendor Id Backward Compatibility................. Disabled
Call Station Id Case............................. lower
Call Station Id Type............................. IP Address
Aggressive Failover.............................. Enabled
Keywrap.......................................... Disabled
Fallback Test:
Test Mode.................................... Off
Probe User Name.............................. cisco-probe
Interval (in seconds)........................ 300
MAC Delimiter for Authentication Messages........ hyphen
MAC Delimiter for Accounting Messages............ hyphen
Authentication Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
Accounting Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
--More or (q)uit current module or to abort
TACACS Configuration
Authentication Servers
Idx Server Address Port State Tout
Authorization Servers
Idx Server Address Port State Tout
Accounting Servers
Idx Server Address Port State Tout
LDAP Configuration
Press Enter to continue or to abort
Local EAP Configuration
User credentials database search order:
Primary ..................................... Local DB
Timer:
Active timeout .............................. 300
Configured EAP profiles:
EAP Method configuration:
EAP-FAST:
Server key ................................
TTL for the PAC ........................... 10
Anonymous provision allowed ............... Yes
Authority ID .............................. 436973636f00000000000000000000
00
Authority Information ..................... Cisco A-ID
Press Enter to continue or to abort
HREAP Group Summary
HREAP Group Summary: Count: 0
Group Name # Aps
Press Enter to continue or to abort
HREAP Group Detail
Press Enter to continue or to abort
Route Info
Number of Routes................................. 0
Destination Network Netmask Gateway
Press Enter to continue or to abort
Qos Queue Length Info
Platinum queue length............................ 100
Gold queue length................................ 75
Silver queue length.............................. 50
Bronze queue length.............................. 25
Press Enter to continue or to abort
Mac Filter Info
Press Enter to continue or to abort
Authorization List
Authorize MIC APs against AAA ................... disabled
Authorize LSC APs against Auth-List ............. disabled
Allow APs with MIC - Manufactured Installed C.... disabled
Allow APs with SSC - Self-Signed Certificate..... disabled
Allow APs with LSC - Locally Significant Cert.... disabled
Load Balancing Info
Aggressive Load Balancing........................ Disabled
Aggressive Load Balancing Window................. 5 clients
Aggressive Load Balancing Denial Count........... 3
Statistics
Total Denied Count............................... 0 clients
Total Denial Sent................................ 0 messages
Exceeded Denial Max Limit Count.................. 0 times
None 5G Candidate Count.......................... 0 times
None 2.4G Candidate Count........................ 0 times
Press Enter to continue or to abort
Dhcp Scope Info
Scope: PUNTOSAP
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 209.165.200.201
Pool End......................................... 209.165.200.229
Network.......................................... 209.165.200.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 0.0.0.0 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 0.0.0.0 0.0.0.0 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
Press Enter to continue or to abort
Exclusion List ConfigurationUnable to retrieve exclusion-list entry
Press Enter to continue or to abort
CDP Configuration
Press Enter to continue or to abort
Country Channels Configuration
Configured Country............................. ES - Spain
KEY: * = Channel is legal in this country and may be configured manually.
A = Channel is the Auto-RF default in this country.
. = Channel is not legal in this country.
C = Channel has been configured for use by Auto-RF.
x = Channel is available to be configured for use by Auto-RF.
(-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11bg :
Channels : 1 1 1 1 1
: 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): A * * * * A * * * * A * * .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11a : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
Press Enter to continue or to abort
WPS Configuration Summary
Auto-Immune
Auto-Immune.................................... Disabled
Client Exclusion Policy
Excessive 802.11-association failures.......... Enabled
Excessive 802.11-authentication failures....... Enabled
Excessive 802.1x-authentication................ Enabled
IP-theft....................................... Enabled
Excessive Web authentication failure........... Enabled
Signature Policy
Signature Processing........................... Enabled
Press Enter to continue or to abort
Custom Web Configuration
Radius Authentication Method..................... PAP
Cisco Logo....................................... Enabled
CustomLogo....................................... None
Custom Title..................................... None
Custom Message................................... None
Custom Redirect URL.............................. None
Web Authentication Type.......................... Internal Default
External Web Authentication URL.................. None
Configuration Per Profile:
Rogue AP Configuration
Rogue Location Discovery Protocol................ Disabled
Rogue on wire Auto-Contain....................... Disabled
Rogue using our SSID Auto-Contain................ Disabled
Valid client on rogue AP Auto-Contain............ Disabled
Rogue AP timeout................................. 1200
MAC Address Classification # APs # Clients Last Heard
Adhoc Rogue Configuration
Detect and report Ad-Hoc Networks................ Enabled
Auto-Contain Ad-Hoc Networks..................... Disabled
Client MAC Address Adhoc BSSID State # APs Last Heard
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
--More-- or (q)uit
MAC Address State # APs Last Heard
Ignore List Configuration
MAC Address
Rogue Rule Configuration
Priority Rule Name State Type Match Hit Count
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 41 mins 2 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +39 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
(Cisco Controller) >
The AP log
AP442b.03dc.0925>
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
'(index 0).
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
logging facility kern
^
% Invalid input detected at '^' marker.
logging facility kern
^
% Invalid input detected at '^' marker.
*Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
0
*Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
*Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
.165.200.230:5246
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established -
HT1695 I have Canon MG3250 air printer but I am unable to print from my I-pad, please can you help?
Please help me to be able to print from my Canon MG3250 Air printer from my I pad.
Your printer is AirPrint capable - make sure your iPad and the printer are on the same WiFi network.
Here's a guide that includes troubleshooting tips:
AirPrint Basics
Maybe you are looking for
-
How to change font size in check printing program in AP Invoice
I would like to know how to change font size in check printing program in Oracle Payables Module for Invoice printing. We are using Oracle standard report to print check. Concurrent program short name : APXPBFEL Prt file : APLASP.prt I modified prt f
-
Configuring OBI Apps 7.9.6.3 When Using Universal Adapter Exclusively
Hello experts, I have been working for a few days in trying to configure a fiscal calendar with universal adapter flat files as the only data source because Great Plains is the data source and since Oracle does not support it, we use universal adapte
-
I installed Firefox4 in english but will change to my native language
I installed Firefox4 in English but will change to my native language which are Swedish. Can I change only spell options? I need control that when I wrote in Swedish on Twitter for exempt.
-
Recovery scenario - Voting disk does not match with the cluster guid
Hi all, Think of you can not start your guest VMs just because it has a corrupted system.img root image. And assume it contains 5 physical disk( which are all created by the RAC template) hence ASM on them. What is the simplest recovery scneario of t
-
Unable to connect to AE 802.11n through airport utility -despite resetting
Hi all, I do realize that there are a number of threads adressing what seems to be my problem, but none of the solutions have worked for me. I have a 2 year old AE 802.11n that has given me flawless wireless network for a long time now. I have for so