Beep before POST 3 - 1 - 4 - 3 Z60m freeze when tilted / moved

is this a system board issue? I pulled the dimms and cpu & put back & now I can boot up but when I move the machine or tilt it ever so gently it will lock up and will only restart if I press & hold power button.
Any chance the Active hard drive protection is bad? I have it turned off now.
PC doctor software test performed - all passed several times.

are you still using the original hdd?
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Similar Messages

Blip before POST

I just installed a 645E Max w/ P4 1.8, and when I boot, before POST, there is a little "blip". It doesn't even sound like a beep - its just a little blip... can anyone help me troubleshoot this if its a problem or is it supposed to do that?? Other than that the system seems to run fine so far..
thanks

I'm sure that's not what I'm hearing... this is before POST

3 beeps at post

When I boot up my computer I'm getting 3 beeps at post... is this normall?
Everything seems to be running fine but this is making me second guess myself....
e6420
MSI p35 Platinum
Corsair DDR2 6400

3 short beeps or 3 long beeps? before or after seeing the POST screen?
do you have any USB Storage devices?

MSI P67A-GD53 (B3) in boot cycle before POST

OK, so I purchased a new Motherboard, CPU and RAM today to complete my upgrade. Having installed everything, I hit the power button, machine turns on... then off after about 4 seconds, before POST, then on again, then off again, repeat ad nauseum until I unplug or flick the power switch on the PSU.
I took everything apart again, put the MB onto of the box (to rule out the chances of it shorting on the case) and plugged in the power, with just the CPU (and fan) and RAM in place. Same thing happens. Tried taking out the RAM, exact same thing.
Nothing has been done to any part yet, this is all out of box spec:
MSI P67A-GD53 (B3)
Corsair XMS3 4GB (2x2GB) DDR3 PC3-12800C9 (CMX4GX3M2A1600C9)
Enermax ELT620AWT +3.3V@28A, +5V@32A, +12V1@22A, +12V2@22A, [email protected], +5VSB@3A
Intel i5 2500K 3.30GHz (Sandybridge) Socket LGA1155
Obviously I've got graphics card, HDDs etc, but none of those are plugged in, for the purposes of troubleshooting. All that's connected is the above. I've tried booting with no RAM installed, same thing happens. I've got access to an old internal 2 pin speaker, scavenged from a buggered HP work PC to try and get a beep code, but I can't see where I'd connect it on this MB.
Is the MB fluffed out of the box, or could it be something else? Any help would be greatly appreciated

Quote from: Jack on 09-September-11, 20:26:28
It needs to be connected to the JFP2-Pin Header (check user manual, page 2-14 for pin definitions).
Just to make sure: Have you connected the 4/8 pin +12V CPU power connector to the mainboard (in addition to the 24-Pin ATX connector)?
Also: Have you unplugged your PSU from A/C power and >>Cleared CMOS<< at any point?
Have you inspected the board's CPU socket for bent/broken pins?
Thanks, I'll give that a try.
Yep
Yep
I've eye-balled it but they're pretty small, so it's hard to tell, but it'd be pretty difficult to bend them as the CPU only fits in one way.

Enhancement for MB01 - Need to check the document before post

Hi All,
I need to check a material document before posting in MB01 for a field "GR/GI Slip No" which we are using to enter "gate entry no".The issue now is as i'm using a table control screen to post GRs in bulk . i want to avoid duplicate GRs of a particular gate entry.during analysis i found that an exit/Badi at MB01 - end may serve my purpose well.
thanks and regards,
sachin soni

Hi,
You may try the EXIT:
MBCF0005 Material document item for goods receipt/issue slip
or BADIs:
MB_BAPI_GOODSMVT_CREATE
MB_BATCH_MASTER
MB_DOCUMENT_BADI
Regards,
Renjith Michael.

Please read "The Forum Rules of Engagement" before posting! HOT NEWS!!

Welcome to the SDN ABAP Development Forums!
Please see the [Forum Rules of Engagement|https://wiki.sdn.sap.com/wiki/display/HOME/RulesofEngagement] before posting to avoid potential problems (e.g. your posts are deleted).
The [ABAP Development Forums|https://forums.sdn.sap.com/category.jspa?categoryID=42] have dedicated forums for the following ABAP related areas:
=> General questions about the ABAP language and language implementations. If in doubt, use this forum and do not cross-post.
=> Tables, views, structures, data elements, domains, search helps and types in the underlying relational database.
=> SAPscript and Smartforms form generation, editing and printing and the corresponding programs.
=> Classical Dynpro, Screen Painter and Controls Framework (ALV grid, Table Controls).
=> Enhancing ABAP code through techniques as CMOD, SMOD and the newer BADIs, Switch and Enhancement Frameworks.
=> Code quality, ABAP Unit, Testing, Debugging, efficient code techniques and database reads, SQL trace tools and Runtime Analysis.
=> Data Transfer Techniques, Batch Data Communication, Legacy System Migration Workbench, Application Link Enabling, IDOCs, BAPIs.
=> ABAP Object definition and implementation including encapsulation, interfaces and inheritance in ABAP Objects.
Please...
- Use the correct or most appropriate forum,
- Do not cross-post or multiple-post, and
- Search for information before asking basic questions, again.
Using these categories will enhance performance in the forums and improve the chances that your questions are answered quickly and more accurately!
Other relevant blogs and rule related infos are:
- Michael Schwandt's blog about [Moving to strict rules to improve quality and control|https://www.sdn.sap.com/irj/sdn/weblogs?blog=/pub/wlg/10047].
- Michael Schwandt's blog about [Quality: Invitation To Clean Up Your Forum Threads|https://www.sdn.sap.com/irj/scn/weblogs?blog=/pub/wlg/11978].
- Please follow-up on your threads and assign points correctly, as this also contributes to the [UN Food Program|https://www.sdn.sap.com/irj/sdn/weblogs?blog=/pub/wlg/7898].
Enjoy the forums and happy posting!!

Start of related discussions about the above rules. Feel free to discuss the rules here...
Dear Jan
Sometime i found very difficuties and time taking process in putting questions in forum bcos i have to elaborate the whole pictorial process in words.
Why Cant we make our this forum more Interactive in way of asking questions by allowing us to attach print preview of what we face in the system.
If you kindly give a glance on this issue and try to implement it for us, forum members like us will be benefited and it will be beneficial for those who are all into in this forum.
Thanks & Regards
Saifur Rahaman

Read Before Posting - Where to find Business Objects Java SDK Resources

Before posting you should look through the various resources below for the answers to your questions. A lot of the "how to" or "where can I find" questions are already answered in the material below.
Search the Forums
Use the search feature in these forums to see if your question has already been answered.
SDK Libraries
[BI 4.0|http://www.sdn.sap.com/irj/boc/sdklibrary]
[BusinessObjects Enterprise XI 3.0|http://www.sdn.sap.com/irj/boc/sdklibrary?rid=/webcontent/uuid/90db428d-71ba-2e10-7eb7-d3286eec5ac0]
[BusinessObjects Enterprise XI Release 2|http://devlibrary.businessobjects.com/BusinessObjectsXIR2SP2/en/devsuite.htm]
[BusinessObjects Enterprise XI Release 1|http://devlibrary.businessobjects.com/BusinessObjectsXI/en/devlib.htm]
Crystal Enterprise 10, Not available online.
[Online Viewable JavaDocs|http://help.sap.com/javadocs/index.htm#sapbobj]
SAP Notes
(Formerly known as the Business Objects Knowledge Base)
This is a good location to find known issues, look up error messages, and general tips and tricks with the BusinessObjects Enterprise product line.
[https://service.sap.com/notes] (this requires logon to the SAP Service Marketplace).
Crystal Reports Server, Crystal Reports and Xcelsius SAP Notes are accessible here:
[https://www.sdn.sap.com/irj/sdn/businessobjects-notes]
Sample Code Search
[BusinessObjects Enterprise SDK|https://wiki.sdn.sap.com/wiki/x/HQBmBQ]
[RAS SDK|https://wiki.sdn.sap.com/wiki/x/HgBmBQ]
[Web Services SDK|https://wiki.sdn.sap.com/wiki/x/HwBmBQ]
[Report Engine SDK|https://wiki.sdn.sap.com/wiki/x/IABmBQ]
[Crystal Reports Java SDK|https://wiki.sdn.sap.com/wiki/x/JgBmBQ]
[Java Reporting Component SDK|https://wiki.sdn.sap.com/wiki/x/JwBmBQ]
Business Objects Downloads
- Service Packs and Fix Packs
- Merge Modules and Installation Packages
- Sample Reports and Databases
[http://service.sap.com/bosap-downloads] (requires logon to SAP Service Marketplace).
Crystal Report For Eclipse
[WIKI|https://www.sdn.sap.com/irj/boc/crystalreports-java]
[Product Portal|https://www.sdn.sap.com/irj/boc/crystalreports-java]
Crystal Reports Server, Crystal Reports, and Xcelsius Downloads
[https://www.sdn.sap.com/irj/sdn/businessobjects-downloads]
Business Objects Articles
[https://www.sdn.sap.com/irj/sdn/businessobjects-articles]
Edited by: Aasavari Bhave on Oct 25, 2011 8:49 AM

Thanks. That was useful.
-Rajini

R61 will not power on, no beeps or POST

My R61 only blinks green power / amber battery for a second and will not turn on. No beep, no POST.
Recently the original battery in the R61 went from about 60% capacity to 3% capacity overnight. Since I had purchased used, I suspected the generic power supply I had bought about a year ago when I got the R61. I ordered an authentic Lenovo power supply, but still got only 3%. All was well since I was using the Thinkpad plugged in to the Lenovo power supply (also worked with generic) but about three days ago the laptop would not power on.
My roomate suggested that the bad battery might be to blame and that I should try it without the battery. I tried it, but still only get green power / amber battery lights for a second and then it shuts down. I have already tried the 10 power button pushing with 30 sec hold after and no response. I just re-set the RAM and back-up battery (also 1 yr. old) to make sure they had not been jostled loose.
Would a new battery help or is the R61 damaged? Don't have much cash, so don't want the possibly damaged R61 to ruin a new battery. Any ideas or is my best bet to buy another R61 / T61 and make use of my RAM, DVD, and HDD?
P.S. I know there are similiar threads already, but none have a solutions and they are about 3 yrs. old.
Thinkpad R61-Product # 7733-11U - 2.0 GHz C2D Centrino / 4GB RAM / 80GB HD / Intel 965 / Intel WIFI / BT / DVD/CD-RW / 1280x800 / WXGA / Win 8.1 / elementary OS Luna
Thinkpad X40 Model # 2371-8EU-niece's new toy

I know this is hard to take but that product line has had known board failures because of it design and chipset. There is basically nothing much you can do to resurrect it at this point in time once that problem has appeard. The most likely failure of this model line was the video chipset that would fail on these boards. If the problem was caught earlier and the heat sink was redone that might have prevent the video from failing causing no boot in your case. But that is what I see and read that these units had lots of video chipset failures and only two of which I fixed the thermal sink on one that is still running and another cleaned out much of the dust as I could and is still working. So I think once this model line hits the black screen boot that usually means it's a gooner.
I am a Volunteer to help others on here-not a HP employee.
Replies aren't online 24/7 because of Time Zone differences.
Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

Log for changes done before posting LIV in Tcode MIRO

Hi
By default data will be fetched from PO/GR for LIV however our users are changing few details such as payment terms, tax code, vendor code, vendor invoice amount etc., before posting LIV in tcode MIRO. We don't have any log for these changes done by our users.
We want to know what are fields which have been changed by our users at the time of doing LIV (i.e. before posting LIV).
Can any one help us in this regard.
Regards
P Karthikeyan

If you know those fields, you can find the differences for those field in table EKKO and EKPO for PO, the similar value will be available for IR in table RBKP and RSEG.
Like as payment term, The payment term is saved in table RBKP - ZTERM for MIRO.
The same will be available in table EKKO - ZTERM for PO.
If the value for both fields are same, then user has not changed the field at the time of MIRO.
If the value mismatched, then user has changes the value in MIRO.
In this way, you can find the differences for other fields.

FI Report showing Discount amount before posting a Document

We are paying Vendor's invoices. While creating document, we enter Discount base amount and payment terms. Discount amount appears only after document is posted. Is there any way I can print/display discount amount before posting the document?
Thank you

Ashok, it's F-43 to create a Vendor Invoice. After creating, when you display the document through FB03, on screen 302, you will find Disc Base, payment term. The Disc Amount would be blank, as it is not yet posted.
Thanks

READ before POSTING !

READ existing messages and answers before posting a new question. This forsum seems a disodered collection of the same question(s) asked hundredts of times with a different "subject".
Otherwise it makes the forum useles... and nobody will really benefit.
thanks.

Thanks, Claudio - but someone's already said that!
imac g5 Mac OS X (10.3.9)

Display of FI document before posting MIGO

Dear All
Is it possible to see FI document before posting MIGO?
regards
Sanjay

Hi Karnekar,
I think what you should first know is that during MIGO, standard accounting entries during Goods Receipt are:
Debit Stock Account
     Credit    GR/IR Clearing Account
If it is a reversal, then it would be the opposite
Debit GR/IR Account
     Credit Stock Account
Now, when you are performing MIGO transaction for receiving, if it is a stock material receiving, then you would already know what are the GL Accounts involved based on the double entries above.
However, if it is consumable items, when you perform MIGO transaction, you will be able to see a new tab called Account Assignment Tab.
Here you will see a particular GL Account.
Use this in the double entries above, which will be
Debit GL Account
      Credit GR/IR Account
which is the same, we just replaced the stock account.
Standard SAP, you can only view the double entries after posting MIGO.
1) Display Material Document
2) Select Doc Info --> Accounting Data
Hope this helps.

FB50&FBCJ, before post the document, print option is available ?

Dear Expert,
Herewith i have attached the screen shot of FB50 document, after simulation, before posting(Document no not generated), in the menu the print option is available , how is it possible is there any user control level seting requred to stop it ? kindly reply me
Thanks & Regards
ILAVARASAN TD

Hi, I doubt, if standard SAP provides option to control such print.
Check with your ABAP team, if it can be controlled with Transaction Variant.
Check with Basis/GRC team, if it can be controlled with Role Authorisation.
Thanks, Deepanshu

Search before post

I have seen users posting new threads, which are discussed earlier and solutions is available in the forums. This just increases the volume of posts.
Can we have a functionality where, before posting a new thread, a search is performed in the forums and similar threads are displayed? If the user does not find a relevant match he/she processed and finally posts the thread?
I did search if similar thread exists before posting
Thanks,
Somar

Hi,
even if you did a search and didn't find a similar thread, this topic has already been discussed a few times. So may be others are facing the same problem. Searching... but not getting a helpful response and so post a new thread.
kind regards
Siggi
PS: here is one result I got while searching with 'searching before posting'. https://forums.sdn.sap.com/click.jspa?searchID=10365424&messageID=4964304
Edited by: Siegfried Szameitat on Apr 3, 2008 12:42 PM

Purpose of this Forum (Server General) *** Please Read Before Posting ***

Welcome to Windows Server General Forum !
This is an English TechNet forum, Please post your queries in English !
Scope:
The name "General" has a very broad significance and sometimes that might lead to some ambiguities.
The scope of this forum is to answer General "Server Administration" related queries pertaining
to Windows Server 2003, Windows Server 2008 / R2 and 2012 operating systems.
Again, "Server Administration" has innumerous aspects and at times it becomes bit difficult to categorize
them.
We try to answer your questions in General or provide troubleshooting support in depth as and when necessary
based on the context of the query.
Questions could be related to AD, GP, Server OS related Queries/issues/errors, general troubleshooting etc…
list is too huge and it's highly difficult to elaborate them here :-)
We understand that this scope and purpose can be a little confusing, we apologize for any confusion.
If you might not know the scope or purpose of this forum, we'll redirect you to read this thread if we need
to explain how this forum works.
Out of Scope:
Queries on following (but not limited to…) are Out of scope in this forum.
Scripting
SBS
- Small Business Server
IIS
Coding/Development:
Windows Client Operating Systems
Exchange
Server
Lync
TFS
SQL
server
Visual
Studio
.Net
SharePoint:
SCCM, SCOM
Third Party Applications
etc…
We might (but do not claim to) answer some of the out of scope questions directly here. If we do,
then it's just a Bonus ! and it's not the purpose or in the scope of what this forum provides.
Moving Threads:
It may happen that, your question might have been moved to this forum in an attempt by another moderator from
a different forum to help you find the correct forum or we might move your threads to an appropriate forum as and when necessary.
If a community member gave you the URL/link of a specific Technet forum, then you may request a move to that
specified forum (If a link to the forum category is specified; you'll still need to pick a specific forum from that category) or thread will be moved to the appropriate forum if a Moderator is around.
NOTE:
We cannot move a thread to another Microsoft forum that's not in the TechNet Forum System such as ASP.net,
IIS.net and Answers.Microsoft.com etc… So we can only provide links to those forums.
Marking Answers:
We propose a reply (such as a link about where to go ask your question) to a recent question as an answer,
and then we will usually wait one week (~7 days) before we mark it as the answer. We prefer you (the Asker/OP - Original Poster) to mark the answer, but we do not require it if you abandon the thread for a long time.
If you (the Asker/OP - Original Poster) refuse to let us propose and mark an answer (without telling us why
and helping us figure out the alternatives/workarounds), then we might need to lock a thread or move it to the Off Topic forum.
Please Read Before Posting:
How
to ask a question efficiently in TechNet forum
We have dedicated Server
Forums for different products/technologies, please consider posting your queries in appropriate forum for better help and support.
If you can't figure out where exactly to post your questions, please seek help in "Where
is the Forum For...?" forum and you will be given a URL/Link to an appropriate forum where you can post your questions.
Official
Microsoft Forum Sites
Credits:
Ed
Price - MSFT (Forum Owner)
This sticky has been created inspired by the Sticky on Where is the Forum for.. forum.
Regards, Santosh
MVP - Directory Services
I do not represent the organisation I work for, all the opinions expressed
here are my own.
This posting is provided "AS IS" with no warranties or guarantees and confers no rights.
Blog | Wiki
If you have issues with your account verification or you can not post images, please get your account verified
by posting request in below linked thread.
Verify Your Account 7

Something new (or not noticed by me before) then as this thread appears as normal discussion in
My Thread view.
Regards, Dave Patrick ....
New UI has this functionality i.e. if you reply on a sticky, it will appears as a 'Discussion' in thread view.
Regards, Santosh
I do not represent the organisation I work for, all the opinions expressed here, are my own and posted AS IS.

Beep before POST 3 - 1 - 4 - 3 Z60m freeze when tilted / moved

Similar Messages

Maybe you are looking for