BEFW11S4 v. 4 needs constant resetting for connection

I have two linksys products -- a BEFCMU10 v2 modem and a BEFW11S4 v4 router.  Between two households, I have given MAC ID access to five machines (4 laptops, 1 iTouch).  
It seems as though the computers (especially our neighbors') have connectivity problems unless I turn the power off and on -- sometimes once a day, sometimes more.  Sometimes that works right away (like this morning), but not always.   Usually I just flip the power strip, but in hopes of figuring out what is the culprit, I just unplugged and plugged the router today.  That connected my laptop immediately.  
What's the deal?  The neighbors don't have access to this manual switch-flipping reset, so they're getting restless.  I have no hardware expertise, so I'm at a loss...
Thanks! 
Message Edited by sresari on 10-25-2008 09:52 AM

Try to Change the wireless settings on router :
Open the setup page of the router using 192.168.1.1 by putting the password as admin with username as blank & under the wireless section change the channel.
And also you can try to upgrade the firmware of router by logging on to www.linksys.com/downloads

Similar Messages

  • Need password reset for HP LaserJet M1536dnf MFP the same as others on this forum.

    I have the same M1536dnf password problem here, I can't access the settings.
    I can't activate the duplex mode without it.
    Thanks

    Hi @HPFix7,
    I see that you need the reset for the printer. I can help you.
    I can send you that information in a private message.
    In the forum beside your handle name just click on the envelope to view it.
    Have a wonderful day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Need password reset for hp mini 1101

    need password reset for hp mini 1101cnu932bkxrplease help

    Hi: Please read this post which should resolve your dilemma. http://h30434.www3.hp.com/t5/Notebook-Operating-Sy​​​​​​​​​​​​​​​​​​​​​stems-and-Software/System-Halt​... Then... You can: 1. Use the unlock code you generated to enter the BIOS
    2. Disable all passwords that are enabled in the BIOS's security menu.
    3. If asked for current password - type the unlock code
    4. For new password, just press ENTER key
    5. Repeat the same for verify password column.

  • Need bios reset for hp dv 40000 I hit 3 time error code is09924

    I need to reset Bios password for hp dv4000 I hit it 3 time error code 09924

    Hi,
    Try entering:     pjfgn
                                      or
                                   wpkkxh
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Windows 7 64Bit - iPhone 3GS Driver needs constant reinstalling for photos

    This is a fairly fresh installation of windows 7 64bit, I can sync my iphone and apps and music work without issue, but the driver that lets me access the photos has recently started showing an "!" every time I connect, I can only access my photos by telling windows 7 to troubleshoot the driver
    it then determines that a driver reinstall is needed which then lets me access the images.. until I re-sync again.
    Any ideas would be good, i dont want to have to reinstall itunes
    Thank you.

    If using a 64-bit version of Windows Vista or Windows 7, type C:\Program Files (x86)\Common Files\Apple\Mobile Device Support\Drivers in the "Search for driver software in this location" field when updating the driver.
    iPhone or iPod is not recognized properly by computer when USB drivers are not installed properly or are out of date
    http://support.apple.com/kb/TS1538
    If above does not work then right click on the iTunes shortcut and select properties. Click the compatibility tab and check the "Run this program in compatibility mode" check box. From the drop down menu choose choose Vista service pack 2 and then click Apply. Now double click the iTunes setup.

  • AirPort Express needs constant resetting?

    I think my AirPort Express is on its last legs. Today a friend of mine came over with his Windows laptop (don't ask). Before we tried anything, I used the AirPort Admin Utility to add his MAC address to my access list and uploaded it to the AX. My AirPort Express network did not appear in his whatever-it-was Windows network utility. So, I used the AirPort Admin Utility to take my WPA2 Personal password off (the name of the network is open, so it still should have appeared in his list). Then the AirPort Express stopped passing the Internet to my MacBook and iMac. I was unable to get even the AirPort Admin Utility to see my AirPort Express after that, but the network was still available in the AirPort menubar.
    I tried un-powering the AirPort Express and plugging it back in. That didn't help. I ended up plugging the DSL modem directly into the iMac and getting back on the Internet (as I am now with Internet sharing and the iMac's AirPort card) so I'm certain that my Internet access is fine and the DSL modem is fine. I ended up doing a soft reset, and hard reset but neither would bring the AirPort Express back to life. I did a factory reset and then I could use the AirPort Admin Utility to put my settings back in, one part at a time. But the AirPort Express won't pass along the Internet with my WPA2 Personal password enabled. And after a second or third update/upload of settings the AirPort Express becomes completely inaccessible without yet another factory reset.
    I got the AX the day they were announced, so it's been humming along for more than two years now. I do have an AppleCare Protection Plan for my Mac mini, so I think the AirPort Express is covered with that. But, if there's anything else I can try before calling Apple, I'd like to give it a whirl.
    -Doug

    Even after a week of messing with it on my own, calling AppleCare Support got it back up and running. We didn't do anything that I hadn't already tried on my own, so I'm not sure exactly what it was that "fixed" it. But, the AirPort Express is now back up and supplying the Internet to my three Macs with all the original settings again.
    -Doug

  • Phone needs constant resetting

    I have a iPhone 5S and everymorning I am unable to receive or send texts and unable to make or receive phone calls.  I have to tuern the phone off and then back on and it works fine until the next day.

    Been there, Apple has a trouble shooting for this kind of problem. 3.1 worked for me.
    here's the link:
    https://support.apple.com/kb/TS3406

  • 160 GB Ipod needs constant resetting in car.

    Hey hopefully someone can help me with this. I have a 160 GB ipod and i play it in the car all the time. Everytime I plug it in, the ipod goes to some sort of car play mode and just starts playing the songs in order and i cant skip or even pause it. If i reset the ipod with it plugged into the car, this stops and plays normally. Anyone know how to get it to stop doing this? Its pretty annoying. Thanks in advance.

    <bump>
    Anyone have a similar problem or know how to fix it?

  • Need mbean details for connecting OIM from SOA

    Hi All,
    we have one requirement where SOA will run an interface whhich contains OIM code. OIM code will update user's end date,send mail to manager and retrun true or false to SOA. I have the code which works fine but now I need to invoke this code from SOA as a wsdl. My question is how SOA will invoke OIM API's? If I rpovide mbean details to SOA then it can run the java code on OIM DB. Please suggest if anybody has worked on this type of requirement.
    Thanks,
    Kalpana.

    Use this:
    http://www.oracle.com/webfolder/technetwork/tutorials/obe/fmw/oim/oim_11g/developing_oim_custom_approval_process_for_resource_provision/developing_oim_custom_approval_process_for_resource_provision.pdf
    They have given example. It's not WSDL but simply using OIM APIs from SOA Workflow.
    They are using Credential Store. Check code of Java Embeded.

  • P43 Neo-3 Board needs cmos reset for each restart

    Greetings, thanks to help from this board, I fixed an earlier problem, but I'm still having one issue.  I updated to the bios recommended for my cpu (the 7514v15.zip file installed via the usb method recommended on this site), and when I start up the computer (immediately after clearing cmos), it says that the bios is incorrect.  If I go into the bios from there, I have tried 1) loading the default settings and 2) loading optimized settings.  Each of those allows me to get into the OS and everything works normally, but if I restart, all of the fans start, etc for about 5 sec and go off about 5 sec, and this pattern repeats without a signal getting to the computer.  If I clear cmos, it works again, but gives me the bios error that I mentioned above.
    Any suggestions?
    Here's the gear (all new):
    N82E16820231209   MEM 2Gx2|GSK F2-6400CL4D-4GBPI-B R   http://www.newegg.com/Product/Product.aspx?Item=N82E16820231209&Tpk=N82E16820231209
    N82E16819115037   CPU INTEL|C2D E8400 3G 775 45N R (E0 stepping)   (coolermaster cooling)
    N82E16813130185   MB MSI P43 NEO3-F 775 RT   
    N82E16814150316   VGA XFX PVT98GYDLU 9800GT 512M RT
    N82E16817341016   PSU OCZ|OCZ500MXSP 500W RT   http://www.newegg.com/Product/Product.aspx?Item=N82E16817341016&Tpk=N82E16817341016
    N82E16811129021   CASE ANTEC|NINE HUNDRED BK RT

    That's not BIOS problem, you have some sort of instability.
    Test with just one memory stick only.
    Try bump memory voltage to 2.1V in BIOS and use 2T.
    Test each one memory stick alone with >>Memtest86<<

  • Need Information For Connecting Access point to WLC 4402

    Hi Friends
    I need Some information for Connecting  my New Access point ( Cisco AIRLAP 1242AG) with WLC(4402) Controller
    In our network set up we have two WLC(4402) we needs to Connect this New Accesspoint To one of our WLC
    My Access point is brand New. I need to Know what all i have to do inorder to connect this AP to the controller (from Acesspoint perspective & WLC perspective)
    I need to Know  what I need to do in AP to connect to the Controller
    Do i need to Assign Static IP Address forAP or after connecting to the switch it automatically gets ip from DHCP and regsiter with controller??
    Do i Need to Configure my AP with default gateway(the switch to which is connected ?) & DO i need to configure the AP with  Controller Ip address ??
    Pls Assist
    Regards
    Safwan

    Hi Scot...
    We tried Connecting the Access Point yesterday, but it failed....
    We are using Cisco 3500 Access point ...
    when we connected , first it automatically got an ip address using DHCP but following error occurred
    P70ca.9bd5.77c6#
    AP70ca.9bd5.77c6#
    AP70ca.9bd5.77c6#
    Not in Bound state.
    *Mar  1 00:13:56.539: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination
    *Mar  1 00:13:56.555: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
    d DHCP address 10.50.11.26, mask 255.255.0.0, hostname AP70ca.9bd5.77c6
    *Mar  1 00:14:04.564: %CAPWAP-3-UNSUPPORTED_WLC_VERSION: Unsupported version 6.0
    .182.0 on WLC USSTLController01
    *Mar  1 00:14:14.564: %CAPWAP-3-UNSUPPORTED_WLC_VERSION: Unsupported version 6.0
    .182.0 on WLC USSTLController01
    *Mar  1 00:14:24.564: %CAPWAP-3-UNSUPPORTED_WLC_VERSION: Unsupported
    version 6.0
    .182.0
    version 6.0
    .182.0
    on WLC USSTLController01
    version 6.0
    .182.0
    Then I COnfigured Ap with  Static ip address & default gateway & controller Ip but tht too didnt work...
    .182.0 on WLC USSTLController01
    AP70ca.9bd5.77c6>
    AP70ca.9bd5.77c6>
    AP70ca.9bd5.77c6>
    AP70ca.9bd5.77c6>
    *Mar  1 00:13:40.908: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C
    3750X-48P (e05f.b907.9a20)
    AP70ca.9bd5.77c6>
    AP70ca.9bd5.77c6>
    AP70ca.9bd5.77c6>en
    Password:
    AP70ca.9bd5.77c6#
    *Mar  1 00:13:48.033: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP
    . Renewing DHCP IP.
    AP70ca.9bd5.77c6#
    AP70ca.9bd5.77c6#
    AP70ca.9bd5.77c6#
    P70ca.9bd5.77c6>
    *Mar  1 00:13:40.908: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C
    3750X-48P (e05f.b907.9a20)
    AP70ca.9bd5.77c6>
    AP70ca.9bd5.77c6>
    AP70ca.9bd5.77c6>en
    Password:
    AP70ca.9bd5.77c6#
    *Mar  1 00:13:48.033: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP
    . Renewing DHCP IP.
    I also  Need to Know Cisco Access point 3500 can be associated with WLC 4402 ( version 6.0.182.0) ??
    Pls Advice How to proceed further

  • CP1525 need cold reset process, cannot access menus

    CP1525 need cold reset process, cannot access menus.  I guess this has to be sent by private message, so I will try to figure that out next.
    I have someone that thinks it is funny to enable only IPv6, set a password and lock everyone out.
    Guess I need to set it up properly and lock the printer down.
    I guessed at my d401 reset (If you could send the real proceedure, just in case)  I would appreciate that also.  I am not sure it is actually properly done.  In addition to the CP1525n.
    Thank You

    Hi @johnwise ,
    I see by your post that you need the reset for the printer. I would be happy to help you.
    I can send you that information in a private message.
    In the forum beside your handle name just click on the envelope to view it.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Password reset for CM1415cfm colour laser

    Hi folks,
    I've recently bought a cm1415 printer over a month ago and stupidly setup a password when i set it up a couple of weeks ago, unfortunatley i've tried all passwords that i can think of but to no avail.
    Athough i can still print to it i can't access the setup on the network now and would like to change the fax settings.
    This printer is only for home/small business use for a four PC network so if someone can tell me how to do a master reset or preferable a workaround so that i don't lose how many pages/toner etc i've used. Worst case scenario if i need a master reset then i will do it if someone can can me how i've looked the documentation but i don see anything if i contact Hp directly and give them my invoice details could they reset it remotley ?.
    Any info please.

    Hi @kiborg777 ,
    I see that you need the reset for the printer.
    I can send you that information in a private message.
    In the forum beside your handle name just click on the envelope to view it.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • On one website I go to for work, it says connection reset while page was loading. I was trying to change the permissions for this website but it doesn't even show up in my permission list. Help please. I need this website for work.

    I have contacted this website tech support and they say this issue is on my end. On certain pages on their web site I try go to it will say connection reset. Connection reset while page was loading. I was trying to do anything and everything I can to make sure firefox is allowing access to all pages on this website. I use this website for work I do.

    The "The connection was reset" error message can be caused by a bug fix for the BEAST (Browser Exploit Against SSL/TLS) attack that the server doesn't handle.
    *[[/questions/918127]]
    *[[/questions/918028]]
    See comment 60 in this bug report for workaround, but be aware that this makes you vulnerable to that BEAST attack.
    *[https://bugzilla.mozilla.org/show_bug.cgi?id=702111 bug 702111] - Servers intolerant to 1/n-1 record splitting. "The connection was reset"

  • WRT54G Ver 6 Constant Need To Reset!

    I purchased a WRT54G Ver 6.0 Router in April to bring to Iraq with me.  I have it connected to my iDirect 3000 Satellite Modem, with the static IP config input into the WRT54G.
    I have two computers on my desk, my personnal XPS 1710 with Vista and my Work D600 Latitude with XP.  Both computers exhibit the same problems at the same time.  I have even had other computers connected and have had the same problem.
    My problem seems to be a constant need to reset the WRT54G Router.  I was connecting wirelessly.  The system seemed to operate fine for a day or two.  I started to have problems with the connection to the internet dropping.  When it did this, I could not connect to the WRT54G setup page either.  I figured something locally here at the Camp in Iraq might have been interfering with the wireless, so I ditched the wireless and have been using wired connections.  The problems have not stopped.  I am constantly having to unplug and reset the router to reconnect.  When it hangs up, I cannot even connect to the setup page.  Occasionally, it will find itself without reseting the router, but most times, I have to reset.
    I have tried factory default reseting and manually reentering my settings.  I have just updated the firmware, but it didn't seem to solve anything.  In the past few minutes while trying to search for this problem here on this forum, the router dropped the connection twice.  The networking icon on the computer still indicates a connection, on the Vista is shows that a local connection is available only (during the problem).
    I have read a little online and this seems to be a common problem for Linksys.  I have 2 more of these routers, one at home and one at my office in the States.  Both have had the problems, just not as severe.  This router requires reseting at least 15 times a day during my 12 hour shift.
    I bought the Linksys Routers because they did have a reputation for reliability and quality.  Boy, I guess I should have researched this one a bit more.
    I have 5 IP addresses from my Satellite ISP, so I am considering configuring the Router as a Switch or HUB, but I am unsure on how to do this, or of it will even solve my problems.
    Any ideas?
    Thanks,
    Vincent

    I am having the almost exactly the same problem. It started about a week ago, (just like alot of others I have read on here recently) and I too will have no access to the set up page once it drops the net. I can still acess other computers on the router, but no net and no router set-up page until I reset it. I'm running the same router, without the firmware update. I have 4 desktops directly into the router..and one laptop wireless. Most of the time, the net will stay on for all the computers for surfing and email. Maybe once or twice a day it will drop access to the internet. a simple unplugging of the power cord resets it and everything is peachy. BUT....try to start a download.(usind DAP *download accelerator plus* or a bit torrent)...WHOA! it's anywhere from an instant drop to maybe ten minutes then drop. Most assuredly it will drop. we have had this router since January, and until a week ago, it worked just fine. no problems. Last week, our ISP upgraded their equipment and increased the bandwidth. (we have to use a cellular connection with a static IP being out in the boonies far enough that cable and DSL are still not available) The problems started at the same time and I thought it might be a problem with them. After testing one of the computers with a direct connection to the internet modem, everything, including a major download, worked just fine. It is definately a router problem. I spent quite a lengthy time on the phone with Linksys tech support, and the nice lady had me change the MTU rate from 1500 to 1300. It seemed to work, but about an hour after being done with the support call, things started to go wonky again. I am just about at my wits end!! Nothing has been changed on the router settings except that one thing that tech support instructed me to do. I am kinda leary about upgrading the firmware because I have been seeing a ton of *my router wont work with firmware update* or *now my router is frozen* posts. I have to type in a ton of settings because I am using a static IP and I really don't want to do all that again!! lol PLEASE, somone have a solution to this problem! It is driving me mad!! I would really hate to have to buy a new router, but my roomate is about to that point if this doesn't get fixed soon.

Maybe you are looking for