BEFW11S4 & VPN

Here's hoping you can help me - I've done everything possible - believe me!  When using my Linksys BEFW11S4 router with my VPN s/w (MS Remote Access - MSRA) .. my VPN is not stable and drops consistently every 10/15/20 minutes.  It is getting very very frustrating!! I believe MSRA is configured for IPSec encryption.  Right now I am trying to undertsand - what is 'IPSec Passthrough' enabled/disabled mean?  This is enabled on the Linksys config page - Security tab/VPN Passthrough section.  I am wondering if this may be contributing to my problem.  Please advise.
When I say I have done everything, I mean this:
wireless laptop is configured to use static ip
wireless router has been upgraded to latest firmware
MTU size has been reset to 1365
port forwarding/triggering has been setup
no firewall S/W
Nothing is working.  Even though the wireless router is probably 3+ years old, it is hard for me to believe it is the H/W.  Someone recommended I buy a NetGear wireless router.  I'm trying to give this one more shot!
Please help if you can .. many thanks!!  Rachel (frustrated in CA)

Hello again,
Yes I was on DHCP - yet Linksys Support suggested I go with assigning Static IP, so I did that and it still isn't working well - dropping consistently every 10 - 15 minutes.  Linksys Support somewhat "guaranteed" me the Static IP assignment would work - and it doesn't.
In any case, yes I am accessing my VPN wireless - via my wireless laptop.  It is my work VPN S/W.  I believe it is built on MSRA - Microsoft Remote Access.
In any case, I talked to a colleague this AM - and I think I've come to the conclusion it is time to buy another router; this one too old to work with new laptop.  He recommended the Linksys WRT54G product. 
Unless you have any other recommendations and/or troubleshooting ideas?
Thanks,
Rachel

Similar Messages

  • Cisco VPN 3.6.3b and BEFW11S4 v2 connection issue

    I'm hoping someone can help with this problem.  I am able to connect to my employers VPN server, but cannot access any of the shared areas.  I've found some documentation that may point to an MTU issue, but adjusting the value on the laptop from 1400 down to 1250 to 1200 doesn't work.  I've tried forcing the value to 1250 using the Router Filter settings with no luck.  IPSEC pass through is enabled on the router as is MAC filtering.
    I've tested the VPN while on-campus and I have no problems.  I also have no problems accessing the internet through the Linksys router with VPN turned off.
    Any ideas?
    Configuration:
    DELL Precision M70 running  XP
    Time Warner RoadRunner
    Motorola Surfboard Cable Modem
    Linksys BEFW11S4 v2 (using wireless connection) FW 1.45.10
    Cisco VPN 3.6.3b

    Ok thanks so much. I will try again. 
    My company's IT guys aren't  being very helpful, won't return my calls, emails, etc. and don't appear to be giving me clear instructions on what I believe to be a standard request.  Not sure why .
    We can't get in as administrators, they have to do it for us, and they are not timely in requests like these.  We are a large company (over 10K employees) and the last time I tried this was with our email client and and Cisco VPN, bundled together. It was a disaster and I don't recommend it.  So this way was supposed to be easier for the user, and for them to help us with questions.  Oh well. 
    I will at least try what you have suggested, and when I get back to work I will see if I can get their public ip address, and see if they will check on the port.  
    I will post back to see if the suggestions from the above post worked.
    Many thanks again for your help!

  • BEFW11S4 V4 Remote Access + VPN

    I cannot seem to find a guide or anything about the BEFW11S4 Version 4 Router and how to set up remote access to it and set up a vpn into its network and make the resources availible to me, does anyone know anything about this router? thanks in advance

    Hi… This is not a VPN router so you would not be able to establish the VPN tunnel using this router. You can establish a windows VPN, depending upon your OS. Go through the setup guide for your OS. You may need to forward the ports used by your Windows VPN. Router would just work as a passthrough device and you can access the resources on the PC you connect to. If you want to access the entire network resources you may need to go for a VPN router i.e. RV or WRV series router.

  • BEFW11S4 & Cisco VPN

    Hope someone can help !
    I have a BEFW11S4 wireless router on which I have connected to my corporate network using the Cisco VPN client for years - worked perfectly.
    The router had a problem where it locked up ever few days - in an attempt to fix I upgraded the firmware to version 1.5.2.02 - now I can't get the VPN to connect
    I can ping the outside IP of the VPN box but can't connect to it.
    If I go around the BEFW11S4 the VPN connects, also I cannot connect any other PC's thru the BEFW11S4
    No other changes were made.
    Thanks for any suggestions and assistance !!

    hi... logon to router's setup page and click on "application & gamings" tab >> click on port triggering...and try triggering those ports which i've mentioned in my previous post, for e.g. in the Triggered Range start port should 45 and End port should be 55... same as in forwarded range... if you face any issues let me know.

  • Problems with new Motorola SB6120 modem and BEFW11S4

    I upgraded to Charter Communication's high-speed Internet and after a couple of weeks purchased the SB6120 modem to replace my old SB4100 as the speed was progressively dwindling.  I cannot get my BEFW11S4 v2.0 router to work with the new modem.  I have spent hours myself, with Charter and with the IT people through my work trying to get it to work (I am a remote office employee).  The modem only works direct to my laptop.  The second PC in the house uses the wireless service from the router so it's offline. I have reset the router to factory defaults.  It looks like the router just does not see anything from the modem.  The modem is a DOCSIS 3.0 unit.  Is this just too much for my old router?
    Thx.

    The MAC address field was already filled, but i cloned it again following your linked instructions. I used the Phys Addr associated with my "Ethernet adapter Local Area Connection #" ("3", in my case).   This did not solve the problem.
    I also noticed an "Ethernet adapter Network Connect Adapter" listing with a different Phys Addr and with a description of "Juniper Network Connect Virtual Adapter".  I think this is used for logging into my employer's VPN network, so I ignored it for the MAC cloning exercise. 
    So, problem still remains:
    - Modem direct to PC works fine
    - Modem to router & router to PC, does not --- but all the lights on the front of the router look normal.
    I looked more into MAC addresses and in the Linksys Setup page there are TWO places showing this:
    - Next to "WAN IP" --- this is where I entered the MAC address from the first paragraph above.
    - Next to "LAN IP" --- this shows the MAC address of the router.
    Do these appear to be the correct MAC addresses for each "location"?
    Any other assistance is appreciated!
    Thanks.

  • Fed up with VPN connection failures

    Cant get a brand new laptop with built in wireless to get a VPN connection with a BEFW11s4 router. Internet is fine. An older laptop works fine. This new labtop even works beautifully with a wireless adapter,not the built in.
    Called Linksys tech support line and they wouldnt even check anything. Basically dismissed me and said its the computer (did I mention is brand new??)Now I read all the problems people are having with VPN and their routers and I cant believe they lied to me.
    (Mod note: Edited post. Non-technical content. Thanks!)
    Message Edited by JOHNDOE_06 on 08-12-2006 11:10 PM

    What do you use for the VPN connection? IPSEC? If you only are using the passthrough function on the router, it can only allow 1 IPSEC session at a time. If you are also using other VPN softwares for that, you may need to open up ports 1723 500 50 51 and 47. This is because your router firewall maybe the cause. Try that first on a static IP for that wireless card. Try to also check if the "wired " connection to your VPN works before going wireless, you would need to do this first regardless of any brand of router...ayt?!
    "The war between heaven and hell depends on the choices we make, and those choices require sacrifice. That's the test"

  • WRT54GX2 trouble with VPN

    My home laptop works wonderfully with wireless WRT54GX2, however, my work computer which connects through VPN hardly ever works.  Linksys techs have tried numberous times to reconfigure ports, change ACK, etc., but I still have problems.  Any ideas?

    Same issue here and am finding no help anywhere.......WRT54GX2 does not work with VPN. I opened ports 500 and 4500, made sure pass through was enabled, upgraded firmware and no luck. My BEFW11S4 worked fine after doing this...too bad it died.
    The only info out there is people asking for help........I have had it!

  • Jabber call to voice mail fails with fast busy over VPN

    I have an issue that I ran into with CIPC phones over a VPN.  If a CIPC phone called over a VPN and started ringing a phone the call would fail with fast busy at the time the call would be forwarded to voicemail.  I found the issue was when remote the CIPC phone would negotiate the g.729 codec, when forwarded to a voicemail pilot over a SIP trunk set to g.711 the call would fail due to codec missmatch when no transcoders are present.
    So now I am running into what I believe to be the same issue with Jabber, when on premise the calls to voice mail work just fine, but when remote they fail.  I can directly call the voicemail pilot without error, but if calling a phone the call gets fast busy at the point we are forwarded to voicemail.  Even though all my regions are set to talk to all other regions on G.711 and the voicemail SIP trunk is set to G.711, I believe with the new features in CUCM9 that a lower speed codec has been negotiated since the we are going over the VPN, or Jabber has done this as it knows it's over VPN (not sure).  WIth CIPC I could go into the settings and turn off the Optimize for Bandwidth check box and the call would negotiate G.711.  With Jabber I can't find anything that would tell my Jabber client to stay on G.711 and I can only imagine this is a codec missmatch as the following are true.
    1. CIPC and Jabber share the same line
    2. VPN established and CIPC optimised for low bandwidth un-checked
    3. Over the same VPN the CIPC phone can leave a voicemail
    4. Over the same VPN the Jabber client gets fast busy once forwarded to voicemail
    5. Voicemail environment is Exchange-UM over SIP trunk
    6. SIP trunk is assigned a Device Pool, that is assigned to a region that all other regions communicate G.711 to
    7. On CIPC if optimised for low bandwidth is checked I get the exact same issue as I get with the Jabber client (fast busy when forwarded to voicemail)
    Would anyone know what I can do in CUCM 9 to fix this issue, as said no issue when all devices are on premise.  Wondering if there is a service parameter or a way to change the codec selection so the Jabber client attempts to always negotiate G.711.  The correct answer would be to get some PVDM DSP resources and kick up a transcoder in my resource group, and that may be what I talk them into doing if I have no other options.                  

    We have been getting the exact same thing for almost a year now... since switching to FiOS Digital Voice in May of last year!  Every time I call in to report it they 'escalate' the issue but it never gets resolved.  The problem seems to be in the initial connection.  Most of the time it works fine but, several times a month, after I call to get messages and it starts to play the new message it goes dead and I get the busy signal.  I get the same message when I call back:  “I’m sorry – that account is in use at this time.  Please try again later!”  I have even called in with my cell phone and get the same message!  I HAVE EVEN used the Internet to see if I could get my messages and, when I hit Play, I get a pop-up saying: “Your Voice Mail box is currently in being accessed; please try again later.  If the problem continues, please contact our Customer Support Center at 1-888-553-1555. We apologize for any inconvenience.”  This is obviously a software bug that Verizon has no clue on how to troubleshoot OR fix!!!  I wonder how many people have the problem and just don’t bother reporting it because of the hassle?  When it first started happening they destroyed my entire mailbox and I had to re-enter the complete mailbox setup again – 3 times!!!  NEVER let them talk you into that!!!  It’s their problem and they need to fix it!!!!!!!  I wish I could go back to the ‘normal’ voicemail we originally had… they want hundred$ to switch back because I’d be breaking my #$@%^&* contract!  Good luck if you have Verizon………

  • Phone Service disconnected over VPN

    Hello,
    I'm using Version 9.2.1 (147214) of Jabber for OS X and I'm using a VPN to connect to my work network with AnyConnect Secure Mobility Client.
    My issue is that Phone Services are disconnected while the Voicemail and Meeting Accounts are functioning as expected.
    My server settings are configured automatically, and I'm using the same saved credentials that work when I'm at the office.
    Any ideas?
    - Ken

    This issue is fixed.
    Once I changed the automatic configuration of the CCMCIP from an IP address to the hostname that my CUCM uses, my phone service registered across the VPN.

  • IP Phone SSL VPN and Split tunneling

    Hi Team,
    I went throught the following document which is very useful:
    https://supportforums.cisco.com/docs/DOC-9124
    The only things i'm not sure about split-tunneling point:
    Group-policy must not be configured with split tunnel or split exclude.  Only tunnel all is the supported tunneling policy
    I could see many implementation when they used split-tunneling, like one of my customer:
    group-policy GroupPolicy1 internal
    group-policy GroupPolicy1 attributes
    banner value This system is only for Authorized users.
    dns-server value 10.64.10.13 10.64.10.14
    vpn-tunnel-protocol ssl-client
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value split-tunnel
    default-domain value prod.mobily.lan
    address-pools value SSLClientPool
    webvpn
      anyconnect keep-installer installed
      anyconnect ssl rekey time 30
      anyconnect ssl rekey method ssl
      anyconnect ask none default anyconnect
    username manager-max password XTEsn4mfYvPwC5af encrypted privilege 15
    username manager-max attributes
    vpn-group-policy GroupPolicy1
    tunnel-group PhoneVPN type remote-access
    tunnel-group PhoneVPN general-attributes
    address-pool SSLClientPool
    authentication-server-group AD
    default-group-policy GroupPolicy1
    tunnel-group PhoneVPN webvpn-attributes
    group-url https://84.23.107.10 enable
    ip local pool SSLClientPool 10.200.18.1-10.200.18.254 mask 255.255.254.0
    access-list split-tunnel remark split-tunnel network list
    access-list split-tunnel standard permit 10.0.0.0 255.0.0.0
    It is working for them w/o any issue.
    My question would be
    - is the limitation about split-tunneling still valid? If yes, why it is not recommended?
    Thanks!
    Eva

    Hi,
    If you're not using certificates in client authentication then the SSL handshake will complete before the user is requested to authenticate with username/password.  If this authentication request fails you will see the SSL session terminated immediately following this failure (as in the logs you provided).  Notice the 5 seconds between the SSL session establishment and termination, this is most likely when the user is being authenticated against the aaa server.  If the phone is failing authentication against an external aaa-server you'll want to investigate the logs on that server to determine the root cause of the failure.  The ASA can also provide confirmation of the authentication request/reject with the command 'show aaa-server'.  If you want to see what's going on at an authentication protocol level you can enable several debugs including "debug aaa authentication|common|internal' and protocol specific debugs such as 'debug radius user|session|all' or 'debug ldap'.
    Did this answer your question? If so, please mark it Answered!

  • Remote Access VPN Clients Cannot Access inside LAN

    I have been asked to set up remote access VPN on an ASA 5505 that I previously had no invlovement with.  I have set it up the VPN using the wizard, they way I normally do, but the clients have no access to anything in the inside subnet, not even the inside interface IP address of the ASA.  Thay can ping each other.  The remote access policy below that I am working on is labeled VPNPHONE, address pool 172.16.20.1-10.  I do not need split tunneling to be enabled.  The active WAN interface is the one labeled outside_cable.
    : Saved
    ASA Version 8.2(1)
    hostname ASA5505
    domain-name default.domain.invalid
    enable password eelnBRz68aYSzHyz encrypted
    passwd eelnBRz68aYSzHyz encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.100.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    pppoe client vpdn group dataDSL
    ip address 76.244.75.57 255.255.255.255 pppoe
    interface Vlan3
    nameif dmz
    security-level 50
    ip address 192.168.9.1 255.255.255.0
    interface Vlan10
    nameif outside_cable
    security-level 0
    ip address 50.84.96.178 255.255.255.240
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    switchport access vlan 10
    interface Ethernet0/2
    switchport access vlan 3
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    clock timezone CST -6
    clock summer-time CDT recurring
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    same-security-traffic permit intra-interface
    object-group service Netbios udp
    port-object eq 139
    port-object eq 445
    port-object eq netbios-ns
    object-group service Netbios_TCP tcp
    port-object eq 445
    port-object eq netbios-ssn
    object-group network DM_INLINE_NETWORK_1
    network-object host 192.168.100.177
    network-object host 192.168.100.249
    object-group service Web_Services tcp
    port-object eq ftp
    port-object eq ftp-data
    port-object eq www
    port-object eq https
    object-group network DM_INLINE_NETWORK_10
    network-object host 192.168.9.10
    network-object host 192.168.9.4
    object-group network DM_INLINE_NETWORK_11
    network-object host 192.168.9.10
    network-object host 192.168.9.4
    object-group network DM_INLINE_NETWORK_2
    network-object host 192.168.9.10
    network-object host 192.168.9.4
    object-group network DM_INLINE_NETWORK_3
    network-object host 192.168.9.10
    network-object host 192.168.9.4
    object-group network DM_INLINE_NETWORK_4
    network-object host 192.168.9.10
    network-object host 192.168.9.4
    object-group network DM_INLINE_NETWORK_5
    network-object host 192.168.9.10
    network-object host 192.168.9.4
    object-group network DM_INLINE_NETWORK_6
    network-object host 192.168.9.10
    network-object host 192.168.9.4
    object-group network DM_INLINE_NETWORK_7
    network-object host 192.168.9.10
    network-object host 192.168.9.4
    object-group network DM_INLINE_NETWORK_8
    network-object host 192.168.9.10
    network-object host 192.168.9.4
    object-group network DM_INLINE_NETWORK_9
    network-object host 192.168.9.10
    network-object host 192.168.9.4
    object-group network VPN
    network-object 192.168.255.0 255.255.255.0
    access-list outside_access_in extended permit icmp any host 76.244.75.61
    access-list outside_access_in extended permit tcp any host 76.244.75.61 eq ftp
    access-list outside_access_in extended permit tcp any host 76.244.75.61 eq ftp-data
    access-list outside_access_in extended permit tcp any host 76.244.75.62 eq www
    access-list outside_access_in extended permit tcp any host 76.244.75.62 eq https
    access-list outside_access_in extended permit tcp any host 76.244.75.59 eq www
    access-list outside_access_in extended permit tcp any host 76.244.75.59 eq https
    access-list outside_access_in extended permit tcp any host 76.244.75.60 eq www
    access-list outside_access_in extended permit tcp any host 76.244.75.60 eq https
    access-list outside_access_in extended permit tcp any host 76.244.75.58 eq www
    access-list outside_access_in extended permit tcp any host 76.244.75.58 eq https
    access-list dmz_access_in remark Quickbooks
    access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_6 host 192.168.100.5 eq 56719
    access-list dmz_access_in remark Quickbooks range
    access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_7 host 192.168.100.5 range 55333 55337
    access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_8 host 192.168.100.5 eq 1434
    access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_9 host 192.168.100.5 eq 49398
    access-list dmz_access_in remark QB
    access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_10 host 192.168.100.5 eq 8019
    access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_2 host 192.168.100.5 eq 2638
    access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_11 host 192.168.100.5 object-group Netbios
    access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_3 host 192.168.100.5 object-group Netbios_TCP
    access-list dmz_access_in extended deny ip host 192.168.9.4 host 192.168.100.5 inactive
    access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_4 any
    access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_5 any
    access-list dmz_access_in remark Printer
    access-list dmz_access_in extended permit ip 192.168.9.0 255.255.255.0 object-group DM_INLINE_NETWORK_1
    access-list dmz_access_in extended permit tcp 192.168.9.0 255.255.255.0 any object-group Web_Services
    access-list dmz_access_in extended permit udp 192.168.9.0 255.255.255.0 any eq domain
    access-list dmz_access_in extended permit icmp 192.168.9.0 255.255.255.0 192.168.255.0 255.255.255.0 echo-reply
    access-list dmz_access_in extended permit icmp 192.168.9.0 255.255.255.0 192.168.100.0 255.255.255.0 echo-reply log disable
    access-list dmz_access_in remark QB probably does not need any udp
    access-list dmz_access_in extended permit udp host 192.168.9.4 host 192.168.100.5 eq 55333 inactive
    access-list dmz_access_in remark QB included in other rule range
    access-list dmz_access_in extended permit tcp host 192.168.9.4 host 192.168.100.5 eq 55333 inactive
    access-list dmz_access_in remark May be required for Quickbooks
    access-list dmz_access_in extended permit icmp host 192.168.9.4 host 192.168.100.5
    access-list CAD_capture extended permit ip host 192.168.9.4 host 192.168.100.5
    access-list CAD_capture extended permit ip host 192.168.100.5 host 192.168.9.4
    access-list inside_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.0
    access-list inside_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.240
    access-list inside_nat0_outbound extended permit ip any 172.16.10.0 255.255.255.240
    access-list inside_nat0_outbound extended permit ip any 172.16.20.0 255.255.255.240
    access-list cad_supplies_RAVPN_splitTunnelAcl standard permit 192.168.100.0 255.255.255.0
    access-list cad_supplies_RAVPN_splitTunnelAcl standard permit 192.168.9.0 255.255.255.0
    access-list dmz_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.0
    access-list outside_cable_access_in extended permit icmp any host 50.84.96.182
    access-list outside_cable_access_in extended permit tcp any host 50.84.96.182 eq ftp
    access-list outside_cable_access_in extended permit tcp any host 50.84.96.182 eq ftp-data
    access-list outside_cable_access_in extended permit tcp any host 50.84.96.183 eq www
    access-list outside_cable_access_in extended permit tcp any host 50.84.96.183 eq https
    access-list outside_cable_access_in extended permit tcp any host 50.84.96.180 eq www
    access-list outside_cable_access_in extended permit tcp any host 50.84.96.180 eq https
    access-list outside_cable_access_in extended permit tcp any host 50.84.96.181 eq www
    access-list outside_cable_access_in extended permit tcp any host 50.84.96.181 eq https
    access-list outside_cable_access_in extended permit tcp any host 50.84.96.179 eq www
    access-list outside_cable_access_in extended permit tcp any host 50.84.96.179 eq https
    access-list Local_LAN_Access standard permit host 0.0.0.0
    access-list vpnusers_spitTunnelACL extended permit ip 192.168.100.0 255.255.255.0 any
    access-list nonat-in extended permit ip 192.168.100.0 255.255.255.0 172.16.20.0 255.255.255.0
    pager lines 24
    logging enable
    logging buffered informational
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    mtu dmz 1500 
    mtu outside_cable 1500
    ip local pool VPN_IP_range 192.168.255.1-192.168.255.10 mask 255.255.255.0
    ip local pool VPN_Phone 172.16.20.1-172.16.20.10 mask 255.255.255.0
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    nat-control
    global (outside) 10 interface
    global (outside_cable) 10 interface
    nat (inside) 0 access-list nonat-in
    nat (inside) 10 0.0.0.0 0.0.0.0
    nat (dmz) 0 access-list dmz_nat0_outbound
    nat (dmz) 10 0.0.0.0 0.0.0.0
    static (inside,outside) 76.244.75.62 192.168.100.25 netmask 255.255.255.255 dns
    static (dmz,outside) 76.244.75.61 192.168.9.123 netmask 255.255.255.255 dns
    static (dmz,outside) 76.244.75.59 192.168.9.124 netmask 255.255.255.255 dns
    static (dmz,outside) 76.244.75.58 192.168.9.4 netmask 255.255.255.255 dns
    static (inside,dmz) 192.168.100.0 192.168.100.0 netmask 255.255.255.0
    static (dmz,outside) 76.244.75.60 192.168.9.10 netmask 255.255.255.255 dns
    static (inside,outside_cable) 50.84.96.183 192.168.100.25 netmask 255.255.255.255 dns
    static (dmz,outside_cable) 50.84.96.182 192.168.9.123 netmask 255.255.255.255 dns
    static (dmz,outside_cable) 50.84.96.180 192.168.9.124 netmask 255.255.255.255 dns
    static (dmz,outside_cable) 50.84.96.179 192.168.9.4 netmask 255.255.255.255 dns
    static (dmz,outside_cable) 50.84.96.181 192.168.9.10 netmask 255.255.255.255 dns
    access-group outside_access_in in interface outside
    access-group dmz_access_in in interface dmz
    access-group outside_cable_access_in in interface outside_cable
    route outside_cable 0.0.0.0 0.0.0.0 50.84.96.177 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    http 192.168.100.0 255.255.255.0 inside
    http 204.107.173.0 255.255.255.0 outside
    http 204.107.173.0 255.255.255.0 outside_cable
    http 0.0.0.0 0.0.0.0 outside_cable
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
    crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport
    crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_cable_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_cable_map interface outside_cable
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map inside_map interface inside
    crypto isakmp enable inside
    crypto isakmp enable outside
    crypto isakmp enable outside_cable
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto isakmp policy 30
    authentication pre-share
    encryption 3des
    hash md5
    group 2
    lifetime 86400
    telnet 192.168.100.0 255.255.255.0 inside
    telnet timeout 5
    ssh 192.168.100.0 255.255.255.0 inside
    ssh 204.107.173.0 255.255.255.0 outside
    ssh 204.107.173.0 255.255.255.0 outside_cable
    ssh 0.0.0.0 0.0.0.0 outside_cable
    ssh timeout 15
    console timeout 0
    vpdn group dataDSL request dialout pppoe
    vpdn group dataDSL localname [email protected]
    vpdn group dataDSL ppp authentication pap
    vpdn username [email protected] password *********
    dhcpd address 192.168.100.30-192.168.100.99 inside
    dhcpd dns 192.168.100.5 68.94.156.1 interface inside
    threat-detection basic-threat
    threat-detection statistics port
    threat-detection statistics protocol
    threat-detection statistics access-list
    threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
    webvpn
    group-policy DefaultRAGroup internal
    group-policy DefaultRAGroup attributes
    dns-server value 192.168.100.5
    vpn-tunnel-protocol IPSec l2tp-ipsec
    group-policy cad_supplies_RAVPN internal
    group-policy cad_supplies_RAVPN attributes
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value cad_supplies_RAVPN_splitTunnelAcl
    group-policy VPNPHONE internal
    group-policy VPNPHONE attributes
    dns-server value 192.168.100.5
    vpn-tunnel-protocol IPSec
    split-tunnel-policy excludespecified
    split-tunnel-network-list value Local_LAN_Access
    client-firewall none
    client-access-rule none
    username swinc password BlhBNWfh7XoeHcQC encrypted
    username swinc attributes
    vpn-group-policy cad_supplies_RAVPN
    username meredithp password L3lRjzwb7TnwOyZ1 encrypted
    username meredithp attributes
    vpn-group-policy cad_supplies_RAVPN
    service-type remote-access
    username ipphone1 password LOjpmeIOshVdCSOU encrypted privilege 0
    username ipphone1 attributes
    vpn-group-policy VPNPHONE
    username ipphone2 password LOjpmeIOshVdCSOU encrypted privilege 0
    username ipphone2 attributes
    vpn-group-policy VPNPHONE
    username ipphone3 password LOjpmeIOshVdCSOU encrypted privilege 0
    username ipphone3 attributes
    vpn-group-policy VPNPHONE
    username oethera password WKJxJq7L6wmktFNt encrypted
    username oethera attributes
    vpn-group-policy cad_supplies_RAVPN
    service-type remote-access
    username markh password nqH+bk6vj0fR83ai0SAxkg== nt-encrypted
    username markh attributes
    vpn-group-policy cad_supplies_RAVPN
    tunnel-group DefaultRAGroup general-attributes
    default-group-policy DefaultRAGroup
    tunnel-group DefaultRAGroup ipsec-attributes
    pre-shared-key *
    tunnel-group DefaultRAGroup ppp-attributes
    authentication ms-chap-v2
    tunnel-group cad_supplies_RAVPN type remote-access
    tunnel-group cad_supplies_RAVPN general-attributes
    address-pool VPN_IP_range
    default-group-policy cad_supplies_RAVPN
    tunnel-group cad_supplies_RAVPN ipsec-attributes
    pre-shared-key *
    tunnel-group VPNPHONE type remote-access
    tunnel-group VPNPHONE general-attributes
    address-pool VPN_Phone
    default-group-policy VPNPHONE
    tunnel-group VPNPHONE ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 1500
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect sqlnet
      inspect skinny 
      inspect sunrpc
      inspect xdmcp
      inspect sip 
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:8b25ecc61861a2baa6d2556a3679cc7c
    : end

    Hi,
    You have your "group-policy" set so that you have excluding some networks from being tunneled.
    In this access-list named Local_LAN_Access you specify "0.0.0.0"
    Doesnt this mean you are excluding all networks from being tunneled? In other words no traffic goes to your tunnel.
    This access-list should only contain your local LAN network from where you are connecting with the VPN Client. If you dont need to access anything on your local LAN while having the VPN on, you don't even need this setting on. You could just tunnel all traffic instead of excluding some networks.
    - Jouni

  • Setting up site to site vpn with cisco asa 5505

    I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
    IP of remote office router is 71.37.178.142
    IP of the main office firewall is 209.117.141.82
    Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
    ciscoasa# show run
    : Saved
    ASA Version 7.2(4)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password TMACBloMlcBsq1kp encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.1.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
    access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto map outside_map 1 match address outside_1_cryptomap
    crypto map outside_map 1 set pfs group5
    crypto map outside_map 1 set peer 209.117.141.82
    crypto map outside_map 1 set transform-set ESP-AES-256-SHA
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption aes-256
    hash sha
    group 5
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    vpdn username [email protected] password ********* store-local
    dhcpd auto_config outside
    dhcpd address 192.168.1.2-192.168.1.129 inside
    dhcpd enable inside
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
    : end
    ciscoasa#
    Thanks!

    Hi Mandy,
    By using following access list define Peer IP as source and destination
    access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
    you are not defining the interesting traffic / subnets from both ends.
    Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
    !.1..source subnet(called local encryption domain) at your end  192.168.200.0
    !..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
    !..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
    !...at your end  192.168.200.0
    !..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
    !...at other end 192.168.100.0
    Please use Baisc Steps as follows:
    A. Configuration in your MAIN office  having IP = 209.117.141.82  (follow step 1 to 6)
    Step 1.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
    Step 2.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 3.
    Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 71.37.178.142
    or , but not both
    crypto isakmp key 6 CISCO123 address71.37.178.142
    step 4.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 5.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 6.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Configure the same but just change ACL on other end in step one  by reversing source and destination
    and also set the peer IP of this router in other end.
    So other side config should look as follows:
    B.  Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
    Step 7.
    Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
    access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
    Step 8.
    Config ISAKMP Policy with minimum 4 parameters are to be config for
    crypto isakmp policy 10
    authentication pre-share  ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
    encryption aes-256   --->2nd parameter of ISAKMP Policy is OK
    hash sha   --->  3rd parameter of ISAKMP Policy is OK
    group 5  --->  4th parameter of ISAKMP Policy is OK
    lifetime 86400  ------ >  this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
    Step 9.
    Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
    Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
    Use following command:
    crypto isakmp key 0 CISCO123 address 209.117.141.82
    or , but not both
    crypto isakmp key 6 CISCO123 address 209.117.141.82
    step 10.
    Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
    Here is yours one:
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
    crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
    or
    crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
    Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
    ah-sha-hmac or  ah-md5-hmac
    crypto ipsec transform-set TSET1 ah-sha-hmac
    or
    crypto ipsec transform-set TSET1 ah-md5-hmac
    Step 11.
    Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
    crypto map    ipsec-isakmp
    1. Define peer -- called WHO to set tunnel with
    2. Define or call WHICH - Transform Set, only one is permissible
    3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
    Like in your case it is but ipsec-isakmp keyword missing in the ;ast
    crypto map outside_map 10 ipsec-isakmp
    1. set peer 209.117.141.82  -----> is correct as this is your other side peer called WHO in my step
    2. set transform-set TSET1  -----> is correct as this is WHICH, and only one transform set can be called
    !..In you case it is correct
    !...set transform-set ESP-AES-256-SHA (also correct)
    3.  match address outside_1_cryptomap  ---->Name of the extended ACL define as WHAT to pass through this tunnel
    4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
    Step 12.
    Now apply this one crypto MAP to your OUTSIDE interface always
    interface outside
    crypto map outside_map
    Now initite a ping
    Here is for your summary:
    IPSec: Site to Site - Routers
    Configuration Steps
    Phase 1
    Step 1: Configure Mirrored ACL/Crypto ACL       for Interesting Traffic
    Step 2: Configure ISAKMP Policy
    Step 3: Configure ISAKMP Key
    Phase 2
    Step 4: Configure Transform Set
    Step 5: Configure Crypto Map
    Step 6: Apply Crypto Map to an Interface
    To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
    Router#debug crpyto isakmp
    Router#debug crpyto ipsec
    Router(config)# logging buffer 7
    Router(config)# logging buffer 99999
    Router(config)# logging console 6
    Router# clear logging
    Configuration
    In R1:
    (config)# access-list 101 permit ipo host 10.1.1.1 host      10.1.2.1
    (config)# crypto isakmp policy 10
    (config-policy)# encryption 3des
    (config-policy)# authentication pre-share
    (config-policy)# group 2
    (config-policy)# hash sha1
    (config)# crypto isakmp key 0 cisco address 2.2.2.1
    (config)# crypto ipsec transform-set TSET esp-3des      sha-aes-hmac
    (config)# crypto map CMAP 10 ipsec-isakmp
    (config-crypto-map)# set peer 2.2.2.1
    (config-crypto-map)# match address 101
    (config-crypto-map)# set transform-set TSET
    (config)# int f0/0
    (config-if)# crypto map CMAP
    Similarly in R2
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Change to Transport Mode, add the following command in Step 4:
    (config-tranform-set)# mode transport
    Even after  doing this change, the ipsec negotiation will still be done through  tunnel mode if pinged from Loopback to Loopback. To overcome this we  make changes to ACL.
    Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
    (config)# crypto isakmp peer address 2.2.2.1
    (config-peer)# set aggressive-mode password cisco
    (config-peer)# set aggressive-mode clien-endpoint       ipv4-address 2.2.2.1
    Similarly on R2.
    The below process is for the negotiation using RSA-SIG (PKI) as authentication type
    Debug Process:
    After  we debug, we can see the negotiation between the two peers. The first  packet of the interesting traffic triggers the ISAKMP (Phase1)  negotiation. Important messages are marked in BOLD and explanation in  RED
    R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
    Packet sent with a source address of 2.2.2.2
    Mar  2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) //  Router tried to find any IPSec SA matching the outgoing connection but  no valid SA has been found in Security Association Database (SADB)
    Mar  2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
    Mar  2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
    Mar  2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
    Mar  2 16:18:42.939: ISAKMP: local port 500, remote port 500
    Mar  2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE    
    Mar  2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
    Mar  2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
    Mar  2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
    Mar  2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
    Mar  2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
    Mar  2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY  New State = IKE_I_MM1
    Mar  2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
    Mar  2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
    Mar  2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1  New State = IKE_I_MM2
    Mar  2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947:.!!!!
    Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
    R2(config)# ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
    Mar  2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
    Mar  2 16:18:42.947: ISAKMP:      encryption 3DES-CBC
    Mar  2 16:18:42.947: ISAKMP:      hash SHA
    Mar  2 16:18:42.947: ISAKMP:      default group 2
    Mar  2 16:18:42.947: ISAKMP:      auth RSA sig
    Mar  2 16:18:42.947: ISAKMP:      life type in seconds
    Mar  2 16:18:42.947: ISAKMP:      life duration (VPI) of  0x0 0x1 0x51 0x80
    Mar  2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
    Mar  2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
    Mar  2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
    Mar  2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
    Mar  2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
    Mar  2 16:18:42.947: ISAKMP:(0): processing vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
    Mar  2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM2
    Mar  2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
    Mar  2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
    Mar  2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2  New State = IKE_I_MM3
    Mar  2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
    Mar  2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3  New State = IKE_I_MM4
    Mar  2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
    Mar  2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
    Mar  2 16:18:43.007:  Choosing trustpoint CA_Server as issuer
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
    Mar  2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
    Mar  2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
    Mar  2 16:18:43.007: ISAKMP:received payload type 20
    Mar  2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
    Mar  2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM4
    Mar  2 16:18:43.011: ISAKMP:(1008):Send initial contact
    Mar  2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
    Mar  2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
    Mar  2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
    Mar  2 16:18:43.011: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : R2
              protocol     : 17
              port         : 500
              length       : 10
    Mar  2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
    Mar  2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
    Mar  2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
    Mar  2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
    Mar  2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4  New State = IKE_I_MM5
    Mar  2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
    // "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP (1008): ID payload
              next-payload : 6
              type         : 2
              FQDN name    : ASA1
              protocol     : 0
              port         : 0
              length       : 12
    Mar  2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
    Mar  2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
    Mar  2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
    Mar  2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
    Mar  2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
    Mar  2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
    Mar  2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
    Mar  2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
    Mar  2 16:18:43.067: ISAKMP:received payload type 17
    Mar  2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
    Mar  2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
    Mar  2 16:18:43.067: ISAKMP:(1008):SA authentication status:
              authenticated
    Mar  2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
    Mar  2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/,  and inserted successfully 46519678. // SA inserted into SADB
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5  New State = IKE_I_MM6
    Mar  2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
    Mar  2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_I_MM6
    Mar  2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
    Mar  2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
    Mar  2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY  New State = IKE_QM_I_QM1
    Mar  2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
    Mar  2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE  New State = IKE_P1_COMPLETE
    Mar  2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
    Mar  2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
    Mar  2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
    Mar  2 16:18:43.079: ISAKMP:   attributes in transform:
    Mar  2 16:18:43.079: ISAKMP:      SA life type in seconds
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (basic) of 3600
    Mar  2 16:18:43.079: ISAKMP:      SA life type in kilobytes
    Mar  2 16:18:43.079: ISAKMP:      SA life duration (VPI) of  0x0 0x46 0x50 0x0
    Mar  2 16:18:43.079: ISAKMP:      encaps is 1 (Tunnel)
    Mar  2 16:18:43.079: ISAKMP:      authenticator is HMAC-SHA
    Mar  2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
    Mar  2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
    Mar  2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
    Mar  2 16:18:43.083:         inbound SA from 20.1.1.10 to 40.1.1.1 (f/i)  0/ 0
              (proxy 1.1.1.1 to 2.2.2.2)
    Mar  2 16:18:43.083:         has spi 0xA9A66D46 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083:         outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
              (proxy 2.2.2.2 to 1.1.1.1)
    Mar  2 16:18:43.083:         has spi  0x2B367FB4 and conn_id 0
    Mar  2 16:18:43.083:         lifetime of 3600 seconds
    Mar  2 16:18:43.083:         lifetime of 4608000 kilobytes
    Mar  2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE    
    Mar  2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
    Mar  2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
    Mar  2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
    Mar  2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1  New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
    Verification Commands
    #show crypto isakmp SA
    #show crypto ipsec SA
    Kindly rate if you find the explanation useful !!
    Best Regards
    Sachin Garg

  • ASA VPN QUESTION

    Hi All
    The question is pretty simple. I can successfully connect  to my ASA 5505  firewall via cisco vpn client 64 bit , i can ping any ip  address on the LAN behind ASA but none of the LAN computers can see or  ping the IP Address which is assigned to my vpn client from the ASA VPN  Pool.
    The LAN behind ASA is 192.168.0.0 and the VPN Pool for the cisco vpn client is 192.168.30.0
    I would appreciate some help pls
    Here is the config:
    ASA Version 7.2(4)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password J7NxNd4NtVydfOsB encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    name 192.168.0.11 EXCHANGE
    name x.x.x.x WAN
    name 192.168.30.0 VPN_POOL2
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.0.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address WAN 255.255.255.252
    interface Ethernet0/0
    switchport access vlan 2
    <--- More --->
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    boot system disk0:/asa724-k8.bin
    ftp mode passive
    clock timezone EEST 2
    clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    object-group protocol TCPUDP
    protocol-object udp
    protocol-object tcp
    access-list nk-acl extended permit tcp any interface outside eq smtp
    access-list nk-acl extended permit tcp any interface outside eq https
    access-list customerVPN_splitTunnelAcl standard permit 192.168.0.0 255.255.255.0
    access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 VPN_POOL2 255.255.255.0
    access-list inside_access_in extended permit ip any any
    access-list VPN_NAT extended permit ip VPN_POOL2 255.255.255.0 192.168.0.0 255.255.255.0
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool VPN_POOL2 192.168.30.10-192.168.30.90 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    global (inside) 10 interface
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    nat (outside) 10 access-list VPN_NAT outside
    static (inside,outside) tcp interface smtp EXCHANGE smtp netmask 255.255.255.255
    static (inside,outside) tcp interface https EXCHANGE https netmask 255.255.255.255
    access-group inside_access_in in interface inside
    access-group nk-acl in interface outside
    route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    aaa authentication enable console LOCAL
    aaa authentication http console LOCAL
    aaa authentication serial console LOCAL
    aaa authentication ssh console LOCAL
    aaa authentication telnet console LOCAL
    aaa authorization command LOCAL
    http server enable
    http 192.168.0.0 255.255.255.0 inside
    snmp-server host inside 192.168.0.16 community public
    no snmp-server location
    no snmp-server contact
    snmp-server community public
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto dynamic-map outside_dyn_map 20 set pfs group1
    crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
    crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    crypto isakmp nat-traversal  20
    telnet 192.168.0.0 255.255.255.0 inside
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcp-client client-id interface outside
    dhcpd dns 217.27.32.196
    dhcpd address 192.168.0.100-192.168.0.200 inside
    dhcpd dns 192.168.0.10 interface inside
    dhcpd enable inside
    group-policy DfltGrpPolicy attributes
    banner none
    wins-server none
    dns-server none
    dhcp-network-scope none
    vpn-access-hours none
    vpn-simultaneous-logins 3
    vpn-idle-timeout 30
    vpn-session-timeout none
    vpn-filter none
    vpn-tunnel-protocol IPSec l2tp-ipsec
    password-storage disable
    ip-comp disable
    re-xauth disable
    group-lock none
    pfs disable
    ipsec-udp disable
    ipsec-udp-port 10000
    split-tunnel-policy tunnelall
    split-tunnel-network-list none
    default-domain none
    split-dns none
    intercept-dhcp 255.255.255.255 disable
    secure-unit-authentication disable
    user-authentication disable
    user-authentication-idle-timeout 30
    ip-phone-bypass disable
    leap-bypass disable
    nem disable
    backup-servers keep-client-config
    msie-proxy server none
    msie-proxy method no-modify
    msie-proxy except-list none
    msie-proxy local-bypass disable
    nac disable
    nac-sq-period 300
    nac-reval-period 36000
    nac-default-acl none
    address-pools none
    smartcard-removal-disconnect enable
    client-firewall none
    client-access-rule none
    webvpn
      functions url-entry
      html-content-filter none
      homepage none
      keep-alive-ignore 4
      http-comp gzip
      filter none
      url-list none
      customization value DfltCustomization
      port-forward none
      port-forward-name value Application Access
      sso-server none
      svc none
      svc keep-installer installed
      svc keepalive none
      svc rekey time none
      svc rekey method none
      svc dpd-interval client none
      svc dpd-interval gateway none
      svc compression deflate
    group-policy customerVPN internal
    group-policy customerVPN attributes
    dns-server value 192.168.0.10
    vpn-tunnel-protocol IPSec
    password-storage enable
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value customerVPN_splitTunnelAcl
    default-domain value customer.local
    username xxx password 8SYsAcRU4s6DpQP1 encrypted privilege 0
    username xxx attributes
    vpn-group-policy TUNNEL1
    username xxx password C6M4Xy7t0VOLU3bS encrypted privilege 0
    username xxx attributes
    vpn-group-policy PAPAGROUP
    username xxx password RU2zcsRqQAwCkglQ encrypted privilege 0
    username xxx attributes
    vpn-group-policy customerVPN
    username xxx password zfP8z5lE6WK/sSjY encrypted privilege 15
    tunnel-group customerVPN type ipsec-ra
    tunnel-group customerVPN general-attributes
    address-pool VPN_POOL2
    default-group-policy customerVPN
    tunnel-group customerVPN ipsec-attributes
    pre-shared-key *
    tunnel-group-map default-group DefaultL2LGroup
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:a4dfbb82008f78756fe4c7d029871ec1
    : end
    ciscoasa#                           

    Well lots of new features have been hinted at for ASA 9.2 but I've not seen anything as far as an Engineering Commit or Customer Commit for that feature.
    Site-site VPN in multiple context mode was added in 9.0(1) and I have customers have been asking for the remote access features as well.
    I will remember to ask about that at Cisco Live next month.

  • ASA 5505 VPN client LAN access problem

    Hello,
    I'm not expert in ASA and routing so I ask some support the following case.
    There is a Cisco VPN client (running on Windows 7) and an ASA5505.
    The goals are client could use remote gateway on ASA for Skype and able to access the devices in ASA inside interface.
    The Skype works well but I cannot access devices in the interface inside via VPN connection.
    Can you please check my following config and give me advice to correct NAT or VPN settings?
    ASA Version 7.2(4)
    hostname ciscoasa
    domain-name default.domain.invalid
    enable password wDnglsHo3Tm87.tM encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.1.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    interface Vlan3
    no forward interface Vlan1
    nameif dmz
    security-level 50
    no ip address
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    access-list inside_access_in extended permit tcp 192.168.1.0 255.255.255.0 any
    access-list inside_access_in extended permit udp 192.168.1.0 255.255.255.0 any
    access-list outside_access_in extended permit ip any 192.168.1.0 255.255.255.0
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    mtu dmz 1500
    ip local pool VPNPOOL 10.0.0.200-10.0.0.220 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    nat-control
    global (outside) 1 interface
    nat (inside) 1 10.0.0.0 255.255.255.0
    nat (inside) 1 192.168.1.0 255.255.255.0
    nat (outside) 1 10.0.0.0 255.255.255.0
    access-group inside_access_in in interface inside
    access-group outside_access_in in interface outside
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    aaa authentication ssh console LOCAL
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto dynamic-map outside_dyn_map 20 set pfs group1
    crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
    crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh 192.168.1.0 255.255.255.0 inside
    ssh timeout 5
    ssh version 2
    console timeout 0
    dhcpd auto_config outside
    dhcpd address 192.168.1.2-192.168.1.33 inside
    dhcpd dns xx.xx.xx.xx interface inside
    dhcpd enable inside
    group-policy DfltGrpPolicy attributes
    banner none
    wins-server none
    dns-server value 84.2.44.1
    dhcp-network-scope none
    vpn-access-hours none
    vpn-simultaneous-logins 3
    vpn-idle-timeout 30
    vpn-session-timeout none
    vpn-filter none
    vpn-tunnel-protocol IPSec l2tp-ipsec webvpn
    password-storage disable
    ip-comp disable
    re-xauth disable
    group-lock none
    pfs disable
    ipsec-udp disable
    ipsec-udp-port 10000
    split-tunnel-policy tunnelall
    split-tunnel-network-list none
    default-domain none
    split-dns none
    intercept-dhcp 255.255.255.255 disable
    secure-unit-authentication disable
    user-authentication disable
    user-authentication-idle-timeout 30
    ip-phone-bypass disable
    leap-bypass disable
    nem enable
    backup-servers keep-client-config
    msie-proxy server none
    msie-proxy method no-modify
    msie-proxy except-list none
    msie-proxy local-bypass disable
    nac disable
    nac-sq-period 300
    nac-reval-period 36000
    nac-default-acl none
    address-pools none
    smartcard-removal-disconnect enable
    client-firewall none
    client-access-rule none
    webvpn
      functions url-entry
      html-content-filter none
      homepage none
      keep-alive-ignore 4
      http-comp gzip
      filter none
      url-list none
      customization value DfltCustomization
      port-forward none
      port-forward-name value Application Access
      sso-server none
      deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information
      svc none
      svc keep-installer installed
      svc keepalive none
      svc rekey time none
      svc rekey method none
      svc dpd-interval client none
      svc dpd-interval gateway none
      svc compression deflate
    group-policy XXXXXX internal
    group-policy XXXXXX attributes
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelall
    split-tunnel-network-list none
    username XXXXXX password G910DDfbV7mNprdR encrypted privilege 15
    username XXXXXX password 5p9CbIe7WdF8GZF8 encrypted privilege 0
    username XXXXXX attributes
    vpn-group-policy XXXXXX
    username XXXXX password cRQbJhC92XjdFQvb encrypted privilege 15
    tunnel-group XXXXXX type ipsec-ra
    tunnel-group XXXXXX general-attributes
    address-pool VPNPOOL
    default-group-policy XXXXXX
    tunnel-group XXXXXX ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:a8fbb51b0a830a4ae823826b28767f23
    : end
    ciscoasa#
    Thanks in advance!
    fbela

    config#no nat (inside) 1 10.0.0.0 255.255.255.0 < This is not required.
    Need to add - config#same-security-traffic permit intra-interface
                                     #access-list extended nonat permit ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0
                                     #nat (inside) 0 access-list nonat
    Please add and test it.
    Thanks
    Ajay

  • SSL VPN, "Login failed" and "WebVPN: error creating WebVPN session!"

    Hi,
    Just ran the wizard for Anyconnect SSL VPN, created a tunnel group, a vpn pool and added user to it. When trying to logon on the SSL service, it simply says "login failed". I suspect that the user might not be in correct groups or so?
    some relevant config
    webvpn
    enable wan
    svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1
    svc enable
    group-policy vpnpolicy1 internal
    group-policy vpnpolicy1 attributes
    vpn-tunnel-protocol svc
    tunnel-group admins type remote-access
    tunnel-group admins general-attributes
    address-pool sslpool2
    default-group-policy vpnpolicy1
    username myuser password 1234567890 encrypted privilege 15
    username myuser  attributes
    vpn-group-policy vpnpolicy1
    Debug:
    asa01# debug webvpn 255
    INFO: debug webvpn  enabled at level 255.
    asa01# webvpn_allocate_auth_struct: net_handle = CD5734D0
    webvpn_portal.c:ewaFormSubmit_webvpn_login[3203]
    webvpn_portal.c:webvpn_login_validate_net_handle[2234]
    webvpn_portal.c:webvpn_login_allocate_auth_struct[2254]
    webvpn_portal.c:webvpn_login_assign_app_next[2272]
    webvpn_portal.c:webvpn_login_cookie_check[2289]
    webvpn_portal.c:webvpn_login_set_tg_buffer_from_form[2325]
    webvpn_portal.c:webvpn_login_transcend_cert_auth_cookie[2359]
    webvpn_login_transcend_cert_auth_cookie: tg_cookie = NULL, tg_name =
    webvpn_portal.c:webvpn_login_set_tg_cookie_form[2421]
    webvpn_portal.c:webvpn_login_set_tg_cookie_querry_string[2473]
    webvpn_portal.c:webvpn_login_resolve_tunnel_group[2546]
    webvpn_login_resolve_tunnel_group: tgCookie = NULL
    webvpn_login_resolve_tunnel_group: tunnel group name from default
    webvpn_login_resolve_tunnel_group: TG_BUFFER = DefaultWEBVPNGroup
    webvpn_portal.c:webvpn_login_negotiate_client_cert[2636]
    webvpn_portal.c:webvpn_login_check_cert_status[2733]
    webvpn_portal.c:webvpn_login_cert_only[2774]
    webvpn_portal.c:webvpn_login_primary_username[2796]
    webvpn_portal.c:webvpn_login_primary_password[2878]
    webvpn_portal.c:webvpn_login_secondary_username[2910]
    webvpn_portal.c:webvpn_login_secondary_password[2988]
    webvpn_portal.c:webvpn_login_extra_password[3021]
    webvpn_portal.c:webvpn_login_set_cookie_flag[3040]
    webvpn_portal.c:webvpn_login_set_auth_group_type[3063]
    webvpn_login_set_auth_group_type: WEBVPN_AUTH_GROUP_TYPE = 4
    webvpn_portal.c:webvpn_login_aaa_not_resuming[3137]
    webvpn_portal.c:http_webvpn_kill_cookie[790]
    webvpn_auth.c:http_webvpn_pre_authentication[2321]
    WebVPN: calling AAA with ewsContext (-867034168) and nh (-849922864)!
    webvpn_add_auth_handle: auth_handle = 17
    WebVPN: started user authentication...
    webvpn_auth.c:webvpn_aaa_callback[5138]
    WebVPN: AAA status = (ACCEPT)
    webvpn_portal.c:ewaFormSubmit_webvpn_login[3203]
    webvpn_portal.c:webvpn_login_validate_net_handle[2234]
    webvpn_portal.c:webvpn_login_allocate_auth_struct[2254]
    webvpn_portal.c:webvpn_login_assign_app_next[2272]
    webvpn_portal.c:webvpn_login_cookie_check[2289]
    webvpn_portal.c:webvpn_login_set_tg_buffer_from_form[2325]
    webvpn_portal.c:webvpn_login_transcend_cert_auth_cookie[2359]
    webvpn_login_transcend_cert_auth_cookie: tg_cookie = NULL, tg_name =
    webvpn_portal.c:webvpn_login_set_tg_cookie_form[2421]
    webvpn_portal.c:webvpn_login_set_tg_cookie_querry_string[2473]
    webvpn_portal.c:webvpn_login_resolve_tunnel_group[2546]
    webvpn_portal.c:webvpn_login_negotiate_client_cert[2636]
    webvpn_portal.c:webvpn_login_check_cert_status[2733]
    webvpn_portal.c:webvpn_login_cert_only[2774]
    webvpn_portal.c:webvpn_login_primary_username[2796]
    webvpn_portal.c:webvpn_login_primary_password[2878]
    webvpn_portal.c:webvpn_login_secondary_username[2910]
    webvpn_portal.c:webvpn_login_secondary_password[2988]
    webvpn_portal.c:webvpn_login_extra_password[3021]
    webvpn_portal.c:webvpn_login_set_cookie_flag[3040]
    webvpn_portal.c:webvpn_login_set_auth_group_type[3063]
    webvpn_login_set_auth_group_type: WEBVPN_AUTH_GROUP_TYPE = 4
    webvpn_portal.c:webvpn_login_aaa_resuming[3093]
    webvpn_auth.c:http_webvpn_post_authentication[1485]
    WebVPN: user: (myuser) authenticated.
    webvpn_auth.c:http_webvpn_auth_accept[2938]
    webvpn_session.c:http_webvpn_create_session[184]
    WebVPN: error creating WebVPN session!
    webvpn_remove_auth_handle: auth_handle = 17
    webvpn_free_auth_struct: net_handle = CD5734D0
    webvpn_allocate_auth_struct: net_handle = CD5734D0
    webvpn_free_auth_struct: net_handle = CD5734D0

    AnyConnect says:
    "The secure gateway has rejected the agents VPN connect or reconnect request. A new connection requires re-authentication and must be started manually. Please contact your network administrator if this problem persists.
    The following message was received from the secure gateway: Host or network is 0"
    Other resources indicate that it's either the tunnel group, or the address pool.. The address pool is:
    ip local pool sslpool2 172.16.20.0-172.16.20.254 mask 255.255.255.0
    asa01# debug webvpn 255
    INFO: debug webvpn  enabled at level 255.
    asa01# debug http 255
    debug http enabled at level 255.
    asa01# webvpn_allocate_auth_struct: net_handle = CE9C3208
    webvpn_portal.c:ewaFormSubmit_webvpn_login[3203]
    webvpn_portal.c:webvpn_login_validate_net_handle[2234]
    webvpn_portal.c:webvpn_login_allocate_auth_struct[2254]
    webvpn_portal.c:webvpn_login_assign_app_next[2272]
    webvpn_portal.c:webvpn_login_cookie_check[2289]
    webvpn_portal.c:webvpn_login_set_tg_buffer_from_form[2325]
    webvpn_portal.c:webvpn_login_transcend_cert_auth_cookie[2359]
    webvpn_login_transcend_cert_auth_cookie: tg_cookie = NULL, tg_name =
    webvpn_portal.c:webvpn_login_set_tg_cookie_form[2421]
    webvpn_portal.c:webvpn_login_set_tg_cookie_querry_string[2473]
    webvpn_portal.c:webvpn_login_resolve_tunnel_group[2546]
    webvpn_login_resolve_tunnel_group: tgCookie = NULL
    webvpn_login_resolve_tunnel_group: tunnel group name from default
    webvpn_login_resolve_tunnel_group: TG_BUFFER = DefaultWEBVPNGroup
    webvpn_portal.c:webvpn_login_negotiate_client_cert[2636]
    webvpn_portal.c:webvpn_login_check_cert_status[2733]
    webvpn_portal.c:webvpn_login_cert_only[2774]
    webvpn_portal.c:webvpn_login_primary_username[2796]
    webvpn_portal.c:webvpn_login_primary_password[2878]
    webvpn_portal.c:webvpn_login_secondary_username[2910]
    webvpn_portal.c:webvpn_login_secondary_password[2988]
    webvpn_portal.c:webvpn_login_extra_password[3021]
    webvpn_portal.c:webvpn_login_set_cookie_flag[3040]
    webvpn_portal.c:webvpn_login_set_auth_group_type[3063]
    webvpn_login_set_auth_group_type: WEBVPN_AUTH_GROUP_TYPE = 4
    webvpn_portal.c:webvpn_login_aaa_not_resuming[3137]
    webvpn_portal.c:http_webvpn_kill_cookie[790]
    webvpn_auth.c:http_webvpn_pre_authentication[2321]
    WebVPN: calling AAA with ewsContext (-845538720) and nh (-828624376)!
    webvpn_add_auth_handle: auth_handle = 22
    WebVPN: started user authentication...
    webvpn_auth.c:webvpn_aaa_callback[5138]
    WebVPN: AAA status = (ACCEPT)
    webvpn_portal.c:ewaFormSubmit_webvpn_login[3203]
    webvpn_portal.c:webvpn_login_validate_net_handle[2234]
    webvpn_portal.c:webvpn_login_allocate_auth_struct[2254]
    webvpn_portal.c:webvpn_login_assign_app_next[2272]
    webvpn_portal.c:webvpn_login_cookie_check[2289]
    webvpn_portal.c:webvpn_login_set_tg_buffer_from_form[2325]
    webvpn_portal.c:webvpn_login_transcend_cert_auth_cookie[2359]
    webvpn_login_transcend_cert_auth_cookie: tg_cookie = NULL, tg_name =
    webvpn_portal.c:webvpn_login_set_tg_cookie_form[2421]
    webvpn_portal.c:webvpn_login_set_tg_cookie_querry_string[2473]
    webvpn_portal.c:webvpn_login_resolve_tunnel_group[2546]
    webvpn_portal.c:webvpn_login_negotiate_client_cert[2636]
    webvpn_portal.c:webvpn_login_check_cert_status[2733]
    webvpn_portal.c:webvpn_login_cert_only[2774]
    webvpn_portal.c:webvpn_login_primary_username[2796]
    webvpn_portal.c:webvpn_login_primary_password[2878]
    webvpn_portal.c:webvpn_login_secondary_username[2910]
    webvpn_portal.c:webvpn_login_secondary_password[2988]
    webvpn_portal.c:webvpn_login_extra_password[3021]
    webvpn_portal.c:webvpn_login_set_cookie_flag[3040]
    webvpn_portal.c:webvpn_login_set_auth_group_type[3063]
    webvpn_login_set_auth_group_type: WEBVPN_AUTH_GROUP_TYPE = 4
    webvpn_portal.c:webvpn_login_aaa_resuming[3093]
    webvpn_auth.c:http_webvpn_post_authentication[1485]
    WebVPN: user: (myuser) authenticated.
    webvpn_auth.c:http_webvpn_auth_accept[2938]
    HTTP: net_handle->standalone_client [0]
    webvpn_session.c:http_webvpn_create_session[184]
    webvpn_session.c:http_webvpn_find_session[159]
    WebVPN session created!
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_remove_auth_handle: auth_handle = 22
    webvpn_portal.c:ewaFormServe_webvpn_cookie[1805]
    webvpn_free_auth_struct: net_handle = CE9C3208
    webvpn_allocate_auth_struct: net_handle = CE9C3208
    ewsStringSearch: no buffer
    Close 0
    webvpn_free_auth_struct: net_handle = CE9C3208
    webvpn_allocate_auth_struct: net_handle = CE9C3208
    webvpn_auth.c:webvpn_auth[581]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:webvpn_update_idle_time[1463]
    WebVPN: session has been authenticated.
    webvpn_free_auth_struct: net_handle = CE9C3208
    webvpn_allocate_auth_struct: net_handle = CE9C3208
    ewsStringSearch: no buffer
    Close 0
    webvpn_free_auth_struct: net_handle = CE9C3208
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:webvpn_update_idle_time[1463]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_allocate_auth_struct: net_handle = CE9C3208
    webvpn_auth.c:webvpn_auth[581]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:webvpn_update_idle_time[1463]
    WebVPN: session has been authenticated.
    webvpn_free_auth_struct: net_handle = CE9C3208
    webvpn_allocate_auth_struct: net_handle = CE9C3208
    ewsStringSearch: no buffer
    Close 0
    webvpn_free_auth_struct: net_handle = CE9C3208
    webvpn_allocate_auth_struct: net_handle = CE863DE8
    webvpn_auth.c:webvpn_auth[581]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:webvpn_update_idle_time[1463]
    WebVPN: session has been authenticated.
    webvpn_free_auth_struct: net_handle = CE863DE8
    webvpn_allocate_auth_struct: net_handle = CE863DE8
    ewsStringSearch: no buffer
    Close 0
    webvpn_free_auth_struct: net_handle = CE863DE8
    webvpn_allocate_auth_struct: net_handle = CE9C32C8
    webvpn_auth.c:webvpn_auth[581]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:webvpn_update_idle_time[1463]
    WebVPN: session has been authenticated.
    webvpn_free_auth_struct: net_handle = CE9C32C8
    webvpn_allocate_auth_struct: net_handle = CE9C32C8
    ewsStringSearch: no buffer
    Close 0
    webvpn_free_auth_struct: net_handle = CE9C32C8
    webvpn_allocate_auth_struct: net_handle = CE9C32C8
    webvpn_allocate_auth_struct: net_handle = CE863DE8
    webvpn_auth.c:webvpn_auth[581]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:webvpn_update_idle_time[1463]
    WebVPN: session has been authenticated.
    webvpn_auth.c:webvpn_auth[581]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:webvpn_update_idle_time[1463]
    WebVPN: session has been authenticated.
    webvpn_free_auth_struct: net_handle = CE863DE8
    webvpn_allocate_auth_struct: net_handle = CE863DE8
    ewsStringSearch: no buffer
    Close 0
    webvpn_free_auth_struct: net_handle = CE863DE8
    webvpn_free_auth_struct: net_handle = CE9C32C8
    webvpn_allocate_auth_struct: net_handle = CE9C32C8
    ewsStringSearch: no buffer
    Close 0
    webvpn_free_auth_struct: net_handle = CE9C32C8
    webvpn_allocate_auth_struct: net_handle = CE9C32C8
    webvpn_auth.c:webvpn_auth[581]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:webvpn_update_idle_time[1463]
    WebVPN: session has been authenticated.
    webvpn_free_auth_struct: net_handle = CE9C32C8
    webvpn_allocate_auth_struct: net_handle = CE9C32C8
    ewsStringSearch: no buffer
    Close 0
    webvpn_free_auth_struct: net_handle = CE9C32C8
    HTTP: Periodic admin session check  (idle-timeout = 1200, session-timeout = 0)
    webvpn_allocate_auth_struct: net_handle = CE9C32C8
    webvpn_auth.c:webvpn_auth[581]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:webvpn_update_idle_time[1463]
    WebVPN: session has been authenticated.
    webvpn_free_auth_struct: net_handle = CE9C32C8
    webvpn_allocate_auth_struct: net_handle = CE9C32C8
    ewsStringSearch: no buffer
    Close 0
    webvpn_free_auth_struct: net_handle = CE9C32C8
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_allocate_auth_struct: net_handle = CE9C32C8
    webvpn_auth.c:webvpn_auth[581]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:webvpn_update_idle_time[1463]
    WebVPN: session has been authenticated.
    webvpn_free_auth_struct: net_handle = CE9C32C8
    webvpn_allocate_auth_struct: net_handle = CE9C32C8
    ewsStringSearch: no buffer
    Close 0
    webvpn_free_auth_struct: net_handle = CE9C32C8
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_allocate_auth_struct: net_handle = CC894AA8
    webvpn_session.c:http_webvpn_find_session[159]
    webvpn_session.c:webvpn_update_idle_time[1463]
    Close 1043041832
    webvpn_free_auth_struct: net_handle = CC894AA8

Maybe you are looking for

  • In Praise of the Quicksilver 2001 - 867 MHz

    Yes, I have newer machines but this one has been working very, very well for over six years and I decided that I was not going to let it go and not give it the Leopard treatment. I find it amazing how well it is working with all the current system up

  • AS 2.0 Loader component question

    I have a site that has a gallery with 40 images, takes a long time to load so I need to find the best way to correct. The files that load manually now are movieclips that play in 10 second frames in their own timeline with an alpha effect on each all

  • MP3 files not showing in iTunes on new iMac

    Hi - I have recently purchased my first Mac computer.  I have copied over all of my music but it seems that all the MP3 files are not playing.  It's strange they show in my folder list of itunes and it lets me play them, but in the main itunes folder

  • Can't update my Photoshop Elements 9, nor install plugin for rw2 formats.

    I'm trying to get my photsop elements 9 to take .rw2 formats, but i can't update neither install the plugin offline. When i try update it says failed to connect, i have a perfect connection.

  • Webpage acts weird in Safari

    Hello, I have a webpage which acts weird in Safari and only in Safari. The PHP-Sessions are not working. Well I use AJAX to write values into the PHP-Sessions and I think it is AJAX who isn't working. But in general, AJAX DOES work with Safari, doesn