Beginner needs help to fix server web, wiki, profile manager

Hi All,
I seem to have messed up my server by changing settings for the hostname.
Now I cant get profile manager, wiki, web to show in Safari anymore.
Can someone please help me with a step by step walkthrough?
Greatly appreciate any help I can get

I have had the same thing and a hostname change is killing for your configuration.
What I suggest is that you backup your stuff and reinstall your server with the correct hostname if possible.

Similar Messages

Need help accessing the router web page. I have been tol...

Need help accessing the router web page. I have been told my router is acting like a switch and the IP address is not in the proper range. I have tried reseting the router (hold for 30 sec and unplug for 5 mins). Didn't work.
thanks

What router are you using? Almost all Linksys routers use 192.168.1.1 as the default local IP address, but there is at least one that uses 192.168.16.1 , namely the WTR54GS (not the WRT54GS).
You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: a few Linksys routers have a default user name of "admin" (with no quotes)), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Message Edited by toomanydonuts on 01-21-2008 04:40 AM

TS1646 I'v tried many times to update my applications however, my account can't do it because security code for my card is incorrect note that I'm sure my card details are correct completely so i need help to fix it as much as you can plz. Thnks

Hi
I'v tried many times to update my applications however, my account can't do it because security code for my card is incorrect note that I'm sure my card details are correct completely so i need help to fix it as much as you can plz. Thnks

Look, I understand I still need a card attached to the account. The problem is, it won't accept my card because I only have 87 cents in my bank account right now.
If I had known there would be so much trouble with the iTunes card, I would have just put the cash in my bank account in the morning instead of buying an iTunes card (I didn't expect the banks to be open on Thanksgiving of course).
Apple will only accept cards that have a balance. The balance is so small in my account that it won't accept it as a valid card.
I'm going to have to contact Apple anyway to reset the security questions. That's obvious. Your answers were not exactly helpful. You didn't tell me anything I don't already know, but thanks for trying to be helpful.

When ever i try to download my iPod recovery software, it keeps saying connection timed out. really annoyed and need help to fix it

when ever i try to download my iPod recovery software, it keeps saying connection timed out. really annoyed and need help to fix it

- Next try the manual install method of:
iDevice Troubleshooting 101 :: iPhone, iPad, iPod touch
If the iPod was Disabled, place the iPod in recovery mode after the firmware download is complete and then restore using the instructions in the article. Sometimes recovery mode timeouts and returns to disabled before the firmware download is complete.
- Then try on another computer

I need help in Fixing my Hp Split x2

I need help in fixing my hp split x2. I got it with windows 8 but i upgraded to Windows 8.1. sine then I stop accessing my D:/ drive ( 500gb HDD)on which I stored data. Besides, I get DCP watchdog violation Error each time I disconnect the tablet and reconnet it. I also get another error message: DCP_DRIVER_POWER_STATE_FAILURE. Can somebody help me out?

Hi Alsaab73,
Thank you for visiting the HP Support Forums and Welcome. I have read your thread on your and getting an error message. The HDD that are you using, I would need the model number. Have you looked in the device manager to see if there is a conflict with the driver installed? It might be listed under the USB devices? Have you tried a different port on the Notebook? Right clicking an updating the driver might be all that is needed.
As per the description of the issue you get error DPC_WATCHDOG_VIOLATION.
Is the issue confined to any particular game or a certain function you are choosing on the Notebook?
The First thing you need to try is disable any firewalls or virus protection and restart the Notebook.
If that does not helps try these steps from Microsoft.
Boot the computer using the Windows 8 bootable DVD.
On the Install Now screen click on Repair your computer.
You will then see a blue screen and an option to choose.
Click on Advanced Options and then click on Troubleshoot.
Click on Automatic Repair and follow the prompted instructions.
Hope this helps.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Re: Beginner needs help using a array of class objects, and quick

Dear Cynthiaw,
I just read your Beginner needs help using a array of class objects, and quick of Dec 7, 2006 9:25 PM . I really like your nice example.
I also want to put a question on the forum and display the source code of my classe in a pretty way as you did : with colors, indentation, ... But how ? In html, I assume. How did you generate the html code of your three classes ? By help of your IDE ? NetBeans ? References ?
I already posted my question with six source code classes ... in text mode --> Awful : See "Polymorphism did you say ?"
Is there a way to discard and replace a post (with html source code) in the Sun forum ?
Thanks for your help.
Chavada

chavada wrote:
Dear Cynthiaw,
I just read your Beginner needs help using a array of class objects, and quick of Dec 7, 2006 9:25 PM . I really like your nice example.You think she's still around almost a year later?
I also want to put a question on the forum and display the source code of my classe in a pretty way as you did : with colors, indentation, ... But how ?Just use [code] and [/code] around it, or use the CODE button
[code]
public class Foo() {
* This is the bar method
public void bar() {
// do stuff
}[/code]

Need help to fix my computer, dude: crashes

I am Manoj. I am from India. There is a problem with my desktop computer. Now days, it gets hanged on regular basis due to which I am unable to work with it. Sometimes it hangs 10-12 times a day. I need help to fix my computer, dude. One more thing sometimes when it hangs, there are many horizontal lines on the monitor and I hear a sound of beep from the CPU.Please help me.
Thanks.

Hello manojyd,
The problem is it could be a huge list of things that is causing the issue.
Let's start by stress testing the system and seeing if it gets too hot.
How to Stress Test your Hardware for Stability and Heat Problems with Prime95
If I have helped you in any way click the Kudos button to say Thanks.
The community works together, click Accept as Solution on the post that solves your issue for other members of the community to benefit from the solution.
- Friendship is magical.

Need help startng websphere server in eclipse for debugging porpose

I am using Eclipse Sdk Version: 3.1.2
IBM websphere 6.0
JDK 1.4
I set debug value to "true" in my application.xml
I have a .ear file of my application deployed on the websphere appserver. Currently I can test my application in nobebug mode.
values of environment variables are -
JAVA_HOME - C:\DEV\IBMJDK142; C:\Program Files\Java\jre1.6.0_03
PATH - C:\DEV\IBMJDK142\bin; C:\Program Files\IBM\WebSphere MQ\Java\lib;C:\DEV\IBMJDK142\bin;%SystemRoot%\system32;%SystemRoot%;
I want to test the application in debug mode.
I am using default server on websphere, which is server1.
In Admin-console of webshere I went to
server-->Application server-->choose server1-->Debugging Service ---->checked the checkbox "Enable service at server startup"
Here value of my JVM debug port is 7777.
next In Eclipse env I chose Run---->Debug....--->Remote Java Application ----> created a new application with the name of my application and set the connection properties to -
Host - localhost
port-7777
Eclipse----> Windows----->Preferences---->Server----->Installed Runtime---->Add---->selected values such as -
JRE - default JRE(JDK 1.4)
IBM Websphere Installation Directory - C:/DEV/WebSphere/AppServer
saved it.
Now in debug perspective, I created a new server with selection/values such as -
IBM--->IBM Websphere v6---->
port - 9081
server profile directory - C:/DEV/WebSphere/AppServer/profiles/default
cell - GCWSNTRANode01Cell
node - GCWSNTRANode01
server - server1
Next---->Added the project to configured project ----->FINISH
Closed Eclipse to save env settings.
Started the default server (server1)
opened eclipse - desired project--->debug perspective ---->choose server--->Right Click----Start/Debug
mesg "Starting ServerI BM Websphere 6 - IBM Websphere 6 failed to start"
can some one please tell me what I am missing here.

Need help startng websphere server in eclipse for debugging porpose
can some one please tell me what I am missing here. Well for one, you're trying to debug a dolphin
Edited by: redfalconf35 on Jun 19, 2008 4:50 PM

HT1206 I can't log into the Itunes store. I type in my Apple ID and my password and the message "This Apple ID cannot be used for the iTunes Store." "Enter another Apple ID." I need help on fixing this.

I can't log into the Itunes store. I type in my Apple ID and my password and the message "This Apple ID cannot be used for the iTunes Store." "Enter another Apple ID." I need help on fixing this.

Yeah I'm starting to see a ton of forums posts right now about the same thing :/ I wonder what's going on

I need help with Mavericks Server: an error occurred while configuring your server. I

I need help with Mavricks Server, I get the following: an error occurred while configuring your server. I have deleted the Server.app several times along with the associated com.apple and Server folder. Any more help would be appreciated.

There are usually some log files around, related to the installation. See if Console.app (Applications > Utilities) shows anything relevant to the error, when you've done a fresh install of Server.app and tried the configuration.

IMac froze after accidentally dropping hundreds of jpegs in desktop.......need help to fix.....desktop filled now..thanks

iMac froze after accidentally dropping hundreds of jpegs in desktop.......need help to fix.....desktop filled now..thanks

Important: mende's suggestion will remove everything from your Desktop, not just the jpegs. Not good. Do the following instead. Open Terminal in Utilities and copy/paste, then hit return after each. The second will create a folder on the Desktop called "photos." The third command will move all of them into that new folder, "photos" This will save them. These commands assume you are logged into the account with the troubled Desktop.
cd ~/Desktop
mkdir photos
mv *.jpg photos/
If you don't care about saving them then the following will delete them. (It is critical that you only use copy/paste.)
cd ~/Desktop
rm *.jpg
Message was edited by: WZZZ

Beginner: Need Help : Label Frame

Beginner: Need Help : Label Frame
Hi everyone,
I am trying to find a way to get my menu bar working. Little info, I am a beginner in Flash just learned the essential DVD from Adobe.
My menu bar has the following:
(About Us) (Services) (Quality) (Projects) (Contact Us)
Each page will have a motion shape tween and slide the page down.
I have type in this actions :
stop();
import flash.events.MouseEvent;
//---aboutus Button Timeline change---\\
aboutus_btn.addEventListener(MouseEvent.CLICK, aboutusClick);
function aboutusClick(event:MouseEvent):void{
gotoAndPlay("aboutus");
//---services Button Timeline change---\\
services_btn.addEventListener(MouseEvent.CLICK, servicesClick);
function servicesClick(event:MouseEvent):void{
gotoAndPlay("services");
//---quality Button Timeline change---\\
quality_btn.addEventListener(MouseEvent.CLICK, qualityClick);
function qualityClick(event:MouseEvent):void{
gotoAndPlay("quality");
//---projects Button Timeline change---\\
projects_btn.addEventListener(MouseEvent.CLICK, projectsClick);
function projectsClick(event:MouseEvent):void{
gotoAndPlay("projects");
//---contactus Button Timeline change---\\
contactus_btn.addEventListener(MouseEvent.CLICK, contactusClick);
function contactusClick(event:MouseEvent):void{
gotoAndPlay("contactus");
This actions only works when I click to the next labels but doesn't work when I want to click back to the previous labels. For example, if I click onto (About Us) to (Services) and (Services) to (Quality) and (Quality) to Projects and (Projects) to (Contact Us)... it all works. If I then click from (Contact Us) back to (Projects) or even any previous buttons... it does NOT work??
Anyone? Please help!

This is my timeline structure. The code for the action frame is in hi-lite in yellow.
Is this clear enough?
I also tried rewriting the action like below, but still have the same problem.
stop();
aboutus_btn.addEventListener(MouseEvent.CLICK, onaboutusClick, false, 0, true);
services_btn.addEventListener(MouseEvent.CLICK, onservicesClick, false, 0, true);
quality_btn.addEventListener(MouseEvent.CLICK, onqualityClick, false, 0, true);
projects_btn.addEventListener(MouseEvent.CLICK, onprojectsClick, false, 0, true);
contactus_btn.addEventListener(MouseEvent.CLICK, oncontactusClick, false, 0, true);
function onaboutusClick(evt:MouseEvent):void {
gotoAndPlay("aboutus");
function onservicesClick(evt:MouseEvent):void {
gotoAndPlay("services");
function onqualityClick(evt:MouseEvent):void {
gotoAndPlay("quality");
function onprojectsClick(evt:MouseEvent):void {
gotoAndPlay("projects");
function oncontactusClick(evt:MouseEvent):void {
gotoAndPlay("contactus");

PKCS12 certificate payloads in OS X Server 10.9 Profile Manager

Hi all,
I'm unable to successfully push .p12 packaged certificate identities to devices managed by OS X Server 10.9 Profile Manager. The problem is that while the file is pushed to the device, it doesn't get unpacked and hence is unable to be used.
I've identified the problem as Profile Manager setting the payload type incorrectly to "com.apple.security.pkcs1" in the profile rather than "com.apple.security.pkcs12". If I strip the profile signing data and edit it, the profile works perfectly when manually installed.
So the questions I have:
1) What's the best way of getting Apple's attention for someone to fix this bug, or is this possibly a browser JavaScript issue incorrectly identifying the payload type (using latest Safari though)?
2) Does anyone know of a workaround to allow this to still be automatically pushed out without having to manually edit and install on each device?
(SCEP is out at the moment due to another issue base64 decoding the SCEP request from Mac OS X devices that I'm taking up with the SCEP server vendor - but iOS works fine)
Thanks!
Al

I'm new to OS X Server and Radius, and have just spent way too many hours trying to figure out what I was doing wrong. I could connect to our enterprise wifi perfectly fine when selecting the certificate from the keychain, but I just couldn't get it to work when I uploaded the .p12 file and used it as the WiFi identity. I tried so many combinations of passphrase, no passphrase, pem format, pkcs12 format, resetting Radius server, resetting whole PKI... But I'd always see Certificate: ?Error_-25257? in the Settings window while I was trying to install the profile, and I couldn't see anything useful in the Radius logs when I tried to connect.
But it turns out, all I needed to do was:
sed -i '' -e '1s/pkcs1/pkcs12/;t' -e '1,/pkcs1/s//pkcs12/' wifi_profile.mobileconfig
(changes the first instance of pkcs1 to pkcs12 - don't change both! I was wondering why it was asking me for a password for our public certificate.)
Will try to update and see if that fixes the problem.

Change Server URL in Profile Manager Enrollment Process?

It appears devices learn the IP or URL of their MDM server during the Profile Manager enrollment process. It must be part of the configuration profile sent to the device. It also appears this is based on the machine's host name. Is there anyway to change that URL - as when the host name of the server changes? If so, where are the files located on the server.
I believe in the previous iPhone Configuration Utility there was a "server URL" and "Check in URL" that could be set. We can't seem to find any parameters in Profile Manger to control the same. Thanks for any help.

Hi Jonathan,
I stumbled on your responses because I was looking for an answer to my own issues.
I am like most just a lay user, although wth 20 years Mac experience.
The issue is as folllows:
I set up Lion Server and I host a Wiki page and I try to run Profile Manager.
I do not have a registered host name. The hostname is server.name.private.
In order to reach the server from the Internet my clients use a DynDNS hostname such as "name.dyndns.org".
My clients can access the Wiki pages with no problems and Safari shows https://name.dyndns.org in the address line.
However, if they want to connect to Profile manager, the server re-directs https://name.dyndns.org/profilemanager https://server.name.private/auth?redirect=https://server.name.private/devicemana gement/api/authentication/callback
which the client's browser cannot resolve because the internal hostname is unknown to public DNS servers.
Why does Profile Manager redirect in the first place ?
Can this issue be resolved without obtaining an "officially registered" hostname ?
Thank you for helping.
Regards,
Twistan

Print server, AD, and Profile Manager

Having a number of issues that I can resolve regarding printing--I am trying to set up profiles in the Profile Manager, but printers are not available or visable. However they are visable in the workgroup manager. The printers reside on Windows print server (2008 R2). Further I can add the printers to my server, but they are not visable in the "Printer Sharing" section of "sharing". So with that, I have a few questions:
1. Do I need to turn on Kerberos in CUPS? User's don't authenticate to our printers via Kerberos, but via the Account manager of the individual printers.
2. Why do settings in Workgroup manager not apply? I can add the printers via LDAP the the new groups I have added, but when I open profile manager the changes or printers are not implemented.
3. How do I make printers visible in Profile Manager?
I have scoured the net and several manuals, but I can seem to stumble upon the correct answer.

Hi,
I have the same issue, very frustrating. Using a Win 2003 AD and 10.8.2 server and clients. If i use WGM I can see all users and groups correctly, but Server.app and Profile Manager does not show them correct.
Strange that we see issues like this since Profile Manager has been around for a while, really interested to hear other peoples experiences.
PS I see a similar thing here: https://discussions.apple.com/thread/4417085?start=0&tstart=0

Beginner needs help to fix server web, wiki, profile manager

Similar Messages

Maybe you are looking for