Benefits vs Disadvantages of using DNS for Oracle RAC (12c or 11g)

For nearly all of my Oracle RAC Builds, I've used /etc/hosts and not DNS. As such I've not been able to take full advantage of GNS and SCANS.
Please note some of your experiences associated with the benefits of using DNS configuration for your Oracle 12c RAC Builds. I'm building my 12c RAC now and I'm starting to configure DNS so that I can provide my customers with better value/add of High Availability. I've used /etc/hosts in the past and one of my arguments in using /etc/hosts can be more secure because you only put in the /etc/hosts what you want the node to know. I also beleave that using /etc/hosts is a lot more simple and perhaps that could be a potential vulnerability. I've decided to start using DNS and to learn how to make it secure.
Your experiences are appreciated. Thanks in Advance!

I see no disadvantages using DNS.
What happens with your clients if your DNS goes down? It stop working?
What is the cost to manage the host files from all host desktop and servers?
I see no reason to not use DNS.
> For nearly all of my Oracle RAC Builds, I've used /etc/hosts and not DNS. As such I've not been able to take full advantage of GNS and SCANS.
Wrong... Full advantage of Clusterware, because is not supported use GNS or SCAN without a DNS.

Similar Messages

Using ZFS for Oracle RAC 11gR2 binaries

Hi,
We have following scenario,
Two Node Cluster: Oracle RAC 11Gr2 with Clusterware on Solaris 10
We want to keep Oracle & Clusterware binaries on ZFS mirror file system on each node locally and for Data files, FRA, Voting disks & OCR on shared SAN using ASM.
My question, is the above scenario certified by Oracle or can we keep Oracle binaries on ZFS...?
Will appreciate your input.
Thanks

Well my confusion started after reading this doc on oracle support:
Certification of Zeta File System (Zfs) On Solaris 10 for Oracle RDBMS [ID 403202.1]
"Oracle database 10gR2 (10.2.0.3 and higher patches), 11gR1 (11.1.0.6 and higher patches) and 11gR2 (11.2.0.1 and higher patches) are certified with Solaris 10 ZFS on Sparc 64-bit and Solaris x84-64. See Solaris ZFS_Best_Practices_Guide. This is for single instance ONLY. ZFS is currently not applicable to RAC and not Certified to use it as a shared filesystem."

Createing a DNS for oracle

I need help creating a DNS for oracle. I am using windows 98 and the database is in my computer. I am trying to create a DNS on the same computer so that i can access it through ASP that is setup on my computer ( Mircrosoft Personel Web Server ) which is very similar to IIS. I tried creating user,system, and file dns but none of them work. I recive a errors when i try to create these, none of them are able to connect to the oracle instance that run on my computer. Please HELP!

Menno,
what do you want exactly? You can calulate in SQL and PLSQL.
SQL> select 10 * 10 from dual;
10*10
100
SQL>
Ton

Export import - using TOAD FOR ORACLE and ORACLE DATABASE 10G EXPRESS or s

Hi all,
Could you please kindly help me?
I am using TOAD FOR ORACLE to export a table to flat file A. The tool just supports to distinguish fields by "spaces".
And the web page of ORACLE DATABASE 10G EXPRESS to import the data from flat file A to another database. To load data to a table from a text file, the web page bases on "comma" to distinguish fields.
So could you have any suggestion for me? I need to export data via TOAD FOR ORACLE. And then import it to another database by the home page of ORACLE DATABASE 10G EXPRESS or sqlplus.
Thank you so much for your help!

Dont use TOAD for exporting your data. Use PL/SQL. Below is the code given in Asktom.com that does what you want.
create or replace function dump_csv( p_query     in varchar2,
                                      p_separator in varchar2 default ',',
                                      p_dir       in varchar2 ,
                                      p_filename in varchar2 )
return number
is
    l_output        utl_file.file_type;
    l_theCursor     integer default dbms_sql.open_cursor;
    l_columnValue   varchar2(2000);
    l_status        integer;
    l_colCnt        number default 0;
    l_separator     varchar2(10) default '';
    l_cnt           number default 0;
begin
    l_output := utl_file.fopen( p_dir, p_filename, 'w' );
    dbms_sql.parse( l_theCursor, p_query, dbms_sql.native );
    for i in 1 .. 255 loop
        begin
            dbms_sql.define_column( l_theCursor, i, l_columnValue, 2000 );
            l_colCnt := i;
        exception
            when others then
                if ( sqlcode = -1007 ) then exit;
                else
                    raise;
                end if;
        end;
    end loop;
    dbms_sql.define_column( l_theCursor, 1, l_columnValue, 2000 );
    l_status := dbms_sql.execute(l_theCursor);
    loop
        exit when ( dbms_sql.fetch_rows(l_theCursor) <= 0 );
        l_separator := '';
        for i in 1 .. l_colCnt loop
            dbms_sql.column_value( l_theCursor, i, l_columnValue );
            utl_file.put( l_output, l_separator || l_columnValue );
            l_separator := p_separator;
        end loop;
        utl_file.new_line( l_output );
        l_cnt := l_cnt+1;
    end loop;
    dbms_sql.close_cursor(l_theCursor);
    utl_file.fclose( l_output );
    return l_cnt;
end dump_csv;
/Here is the link to this thread in asktom.
http://asktom.oracle.com/pls/asktom/f?p=100:11:0::::P11_QUESTION_ID:95212348059

Why do we use reverse proxy for Oracle RAC Cluster setup

Hello All,
I got this question lately.. "why do we use reverse proxy for Oracle RAC Cluster setup". I know we use the reverse proxy at Middleware level for multiple security reasons.
Thanks..

"why do we use reverse proxy for Oracle RAC Cluster setup".
I wouldn't. I wouldn't use a proxy of any sort for the Cluster Interconnect for sure.
Cheers,
Brian

How to add additional disks on vmware OEL4 and use it for Oracle 10gR2?

I created a virtual machine on vmware workstation 6 and installed OEL4.
during first install I created 20 GB disk but now I want to add more disks.
from vmware documentation I tried to add more 8 gb disk to the virtual host.
under devices I see two lines;
Hard Disk (SCSI 0:0) 20.0 GB
Hard Disk (SCSI 0:2) 8.0 GB
but I must be missing some step since I can not see 20 + 8 gb at df;
[root@antuhost ~]# df -h
Filesystem            Size Used Avail Use% Mounted on
/dev/sda1              13G 9.7G 2.3G 82% /
none                  506M     0 506M   0% /dev/shm
/dev/sda2             4.9G 851M 3.8G 19% /homeThank you.

Oh the check the answer from Re: How to add additional disks on vmware OEL4 and use it for Oracle 10gR2?

Disadvantages of using DNS in names.

Hi everyone,
Can anyone explain the disadvantages of using DNS in names in weblogic cluster.
Regards,
Vardhan.

Hi,
One of the very common disadvantage of the BDC is that it doesnt take into account the configuration settings of the screen. Suppose you make any changes in the screen fields (e.g. you make some of the fields in the screen non editable or you make the fields invisible), in this case BDC will throw an error message beacuse the screen mentioned will now no more contain that field or the field will now no more will be an input field.
If at all there is change in the screen settings or transaction look and feel is changed or screen manouvering is changed in the transaction then the BDC will fail and will give error messages.
This is the major disadvantage of using a BDC
Reward points if found useful
Mayank Agarwal

Because it is better to use ADF for oracle SOA/BPM

because it is better to use ADF for oracle SOA/BPM?
TKY for your answers
yango901

Generally it is if you're comparing identical compressors & resolutions but there's something else happening here. If you're worried about quality degrading; check the original file details on the camera (or card) either with Get Info or by opening in QuickTime and showing info. You should find the iPhoto version (reveal in a Finder) is a straight copy. You can't really increase image quality of a movie (barring a few tricks) by increasing file size but Apple editing products create a more "scrub-able" intermediate file which is quite large.
Good luck and happy editing.

Encountered ora-29701 during Sun Cluster for Oracle RAC 9.2.0.7 startup (UR

Hi all,
Need some help from all out there
In our Sun Cluster 3.1 Data Service for Oracle RAC 9.2.0.7 (Solaris 9) configuration, my team had encountered
ora-29701 *Unable to connect to Cluster Manager*
during the startup of the Oracle RAC database instances on the Oracle RAC Server resources.
We tried the attached workaround by Oracle. This workaround works well for the 1^st time but it doesnt work anymore when the server is rebooted.
Kindly help me to check whether anyone encounter the same problem as the above and able to resolve. Thanks.
Bug No. 4262155
Filed 25-MAR-2005 Updated 11-APR-2005
Product Oracle Server - Enterprise Edition Product Version 9.2.0.6.0
Platform Linux x86
Platform Version 2.4.21-9.0.1
Database Version 9.2.0.6.0
Affects Platforms Port-Specific
Severity Severe Loss of Service
Status Not a Bug. To Filer
Base Bug N/A
Fixed in Product Version No Data
Problem statement:
ORA-29701 DURING DATABASE CREATION AFTER APPLYING 9.2.0.6 PATCHSET
*** 03/25/05 07:32 am ***
TAR:
PROBLEM:
Customer applied 9.2.0.6 patchset over 9.2.0.4 patchset.
While creating the database, customer receives following error:
ORA-29701: unable to connect to Cluster Manager
However, if customer goes from 9.2.0.4 -> 9.2.0.5 -> 9.2.0.6, the problem does not occur.
DIAGNOSTIC ANALYSIS:
It seems that the problem is with libskgxn9.so shared library.
For 9.2.0.4 -> 9.2.0.5 -> 9.2.0.6, the install log shows the following:
installActions2005-03-22_03-44-42PM.log:,
[libskgxn9.so->%ORACLE_HOME%/lib/libskgxn9.so 7933 plats=1=>[46]langs=1=> en,fr,ar,bn,pt_BR,bg,fr_CA,ca,hr,cs,da,nl,ar_EG,en_GB,et,fi,de,el,iw,hu,is,in, it,ja,ko,es,lv,lt,ms,es_MX,no,pl,pt,ro,ru,zh_CN,sk,sl,es_ES,sv,th,zh_TW, tr,uk,vi]]
installActions2005-03-22_04-13-03PM.log:, [libcmdll.so ->%ORACLE_HOME%/lib/libskgxn9.so 64274 plats=1=>[46] langs=-554696704=>[en]]
For 9.2.0.4 -> 9.2.0.6, install log shows:
installActions2005-03-22_04-13-03PM.log:, [libcmdll.so ->%ORACLE_HOME%/lib/libskgxn9.so 64274 plats=1=>[46] langs=-554696704=>[en]] does not exist.
This means that while patching from 9.2.0.4 -> 9.2.0.5, Installer copies the libcmdll.so library into libskgxn9.so, while patching from 9.2.0.4 -> 9.2.0.6 does not.
ORACM is located in /app/oracle/ORACM which is different than ORACLE_HOME in customer's environment.
WORKAROUND:
Customer is using the following workaround:
cd $ORACLE_HOME/rdbms/lib make -f ins_rdbms.mk rac_on ioracle ipc_udp
RELATED BUGS:
Bug 4169291

Check if following MOS note helps.
Series of ORA-7445 Errors After Applying 9.2.0.7.0 Patchset to 9.2.0.6.0 Database (Doc ID 373375.1)

How to set JDBC Data Sources in Oracle MapViewer for Oracle database 12c Release 1 (12.1.0.1)

How to set JDBC Data Sources in Oracle MapViewer for Oracle database 12c Release 1 (12.1.0.1)?
The following is my configuration in the conf\mapViewerConfig.xml:
<map_data_source name="mvdemo12"
jdbc_host="127.0.0.1"
jdbc_sid="orcl12c1"
jdbc_port="1522"
jdbc_user="mvdemo"
jdbc_password="7OVl2rJ+hOYxG5T3vKJQb+hW4NPgy9EN"
jdbc_mode="thin"
number_of_mappers="3"
allow_jdbc_theme_based_foi="true"
editable="true"/>

But it does not work.
After use "sqlplus mvdemo/[email protected]:1522/pdborcl", it connected to the Oracle database 12c.
Does anyone know it?
Thanks,

For 11.1.1.7.1 use the syntax for jdbc_sid, i.e.
//mypdb1.foo.com as described in the README,
- MapViewer native (non-container) data sources can now use database service name in place of SID. To supply a db service name, you will use the same jdbc_sid attribute, but specify the service name with double slashes in front, such as follows:
<map_data_source name="myds"
    jdbc_host="foo.com"
    jdbc_sid="//mypdb1.foo.com"
    jdbc_port="1522"
/>
For 11.1.1.7.0 use a container_ds instead.
i.e. instead of using
<map_data_source name="my_12c_test"
                   jdbc_host="mydbinstance"
                   jdbc_sid="pdborcl12c"
                   jdbc_port="1522"
                   jdbc_user="mytestuser"
                   jdbc_password="m2E7T48U3LfRjKwR0YFETQcjNb4gCMLG8/X0KWjO00Q="
                   jdbc_mode="thin"
                   number_of_mappers="6"
                   allow_jdbc_theme_based_foi="false"
                   editable="false"
   />
use
<map_data_source name="my_12c_test"
                   container_ds="jdbc/db12c"
                   number_of_mappers="6"
                   allow_jdbc_theme_based_foi="false"
                   editable="false"
   />
In my case the Glassfish 3.1.2.2 JDBC connection pool definition was
Property
url jdbc:oracle:thin:@mydbinstance:1522/pdborcl12c.rest_of.service.name
Uncheck the Wrap JDBC Objects option in Advanced panel, i.e. the Edit JDBC Connection Pool Advanced properties page.
Add a JDBC resource for that newly created pool
Use that in mapviewerconfig.xml as above

Gig Ethernet V/S SCI as Cluster Private Interconnect for Oracle RAC

Hello Gurus
Can any one pls confirm if it's possible to configure 2 or more Gigabit Ethernet interconnects ( Sun Cluster 3.1 Private Interconnects) on a E6900 cluster ?
It's for a High Availability requirement of Oracle 9i RAC. i need to know ,
1) can i use gigabit ethernet as Private cluster interconnect for Deploying Oracle RAC on E6900 ?
2) What is the recommended Private Cluster Interconnect for Oracle RAC ? GiG ethernet or SCI with RSM ?
3) How about the scenarios where one can have say 3 X Gig Ethernet V/S 2 X SCI , as their cluster's Private Interconnects ?
4) How the Interconnect traffic gets distributed amongest the multiple GigaBit ethernet Interconnects ( For oracle RAC) , & is anything required to be done at oracle Rac Level to enable Oracle to recognise that there are multiple interconnect cards it needs to start utilizing all of the GigaBit ethernet Interfaces for transfering packets ?
5) what would happen to Oracle RAC if one of the Gigabit ethernet private interconnects fails
Have tried searching for this info but could not locate any doc that can precisely clarify these doubts that i have .........
thanks for the patience
Regards,
Nilesh

Answers inline...
Tim
Can any one pls confirm if it's possible to configure
2 or more Gigabit Ethernet interconnects ( Sun
Cluster 3.1 Private Interconnects) on a E6900
cluster ?Yes, absolutely. You can configure up to 6 NICs for the private networks. Traffic is automatically striped across them if you specify clprivnet0 to Oracle RAC (9i or 10g). That is TCP connections and UDP messages.
It's for a High Availability requirement of Oracle
9i RAC. i need to know ,
1) can i use gigabit ethernet as Private cluster
interconnect for Deploying Oracle RAC on E6900 ? Yes, definitely.
2) What is the recommended Private Cluster
Interconnect for Oracle RAC ? GiG ethernet or SCI
with RSM ? SCI is or is in the process of being EOL'ed. Gigabit is usually sufficient. Longer term you may want to consider Infiniband or 10 Gigabit ethernet with RDS.
3) How about the scenarios where one can have say 3 X
Gig Ethernet V/S 2 X SCI , as their cluster's
Private Interconnects ? I would still go for 3 x GbE because it is usually cheaper and will probably work just as well. The latency and bandwidth differences are often masked by the performance of the software higher up the stack. In short, unless you tuned the heck out of your application and just about everything else, don't worry too much about the difference between GbE and SCI.
4) How the Interconnect traffic gets distributed
amongest the multiple GigaBit ethernet Interconnects
( For oracle RAC) , & is anything required to be done
at oracle Rac Level to enable Oracle to recognise
that there are multiple interconnect cards it needs
to start utilizing all of the GigaBit ethernet
Interfaces for transfering packets ?You don't need to do anything at the Oracle level. That's the beauty of using Oracle RAC with Sun Cluster as opposed to RAC on its own. The striping takes place automatically and transparently behind the scenes.
5) what would happen to Oracle RAC if one of the
Gigabit ethernet private interconnects fails It's completely transparent. Oracle will never see the failure.
Have tried searching for this info but could not
locate any doc that can precisely clarify these
doubts that i have .........This is all covered in a paper that I have just completed and should be published after Christmas. Unfortunately, I cannot give out the paper yet.
thanks for the patience
Regards,
Nilesh

Copper cable / GigE Copper Interface as Private Interconnect for Oracle RAC

Hello Gurus
Can some one confirm if the copper Cables ( Cat5/RJ45) can be used for Gig Ethernet i.e. Private interconnects for deploying Oracle RAC 9.x or 10gR2 on Solaris 9/10 .
i am planning to use 2 X GigE Interfaces (one port each from X4445 Quad Port Ethernet Adapters) & Planning to connect it using copper cables ( all the documents that i came across is been refering to the fiber cables for Private Interconnects , connecting GigE Interfaces , so i am getting bit confused )
would appretiate if some one can throw some lights on the same.
regards,
Nilesh Naik
thanks

Cat5/RJ45 can be used for Gig Ethernet Private interconnects for Oracle RAC. I would recommend trunking the two or more interconnects for redundancy. The X4445 adapters are compatible with the Sun Trunking 1.3 software (http://www.sun.com/products/networking/ethernet/suntrunking/). If you have servers that support the Nemo framework (bge, e1000g, xge, nge, rge, ixgb), you can use the Solaris 10 trunking software, dladmin.
We have a couple of SUN T2000 servers and are using the onboard GigE ports for the Oracle 10gR2 RAC interconnects. We upgraded the onboard NIC drivers to the e1000g and used the Solaris 10 trunking software. The next update of Solaris will have the e1000g drivers as the default for the SUN T2000 servers.

Any Oracle best practice/standards for inter-DataCente links for Oracle RAC

Hello Oracle Experts,
Am working for a customer to set up Oracle RAC architecture hosting SAP/Non-SAP applications per SLA levels(MC/BC/Standard) specs. Currently my network team needs calculation to arrive at whether we will go for a (1), (2) or (3) 10Gig links for inter DC (Data-Center) for Oracle RAC.. below is additional background:
•     Porting all client SAP/Non-SAP Oracle databases to new 2 data-centers.
•     There will be 10 blades (4x BL680s and 6x BL460s) in each DC (can scale-up/out later on).
•     Clusters architecture to support Extended/Stretched RAC cluster feature
•     Clusters 2-node each(1-datacenter1, 1-datacenter2) and nodes distributed across 2 x c7000 such that no cluster has more than one node in an enclosure.
•     Each node will have - 4 NIC ports ( 2 x public and 2 x private) , 2 dual-port HBA
•     Oracle ASM/ACFS (ASM Cluster File System), Voting Disk, OCR and Database files
•     the versions are Oracle 11g RAC, Oracle 10g RAC and Oracle 9i (for DataGuard/Standby) on RHEL 6 on Proliant Blades (x86) + BladeMatrix
My network colleagues considering using DWDM across the 2 DCs(given the lesser cost?). Am still looking around if there are any Oracle/industry-best practices around this and having a calculation to support that..
Many Thanks in advance..
Regards,
Abhijit

Hi ,
There are no specific set of steps / practices for batch loading contents to ucm . It would be very much dependent on how many contents does the user have to load to UCM and how well the server is configured in terms of performance .
You can get more details from the following documentation link : http://docs.oracle.com/cd/E21043_01/doc.1111/e10792/c02_settings009.htm
Thanks,
Srinath

If use MSSQ , when oracle rac node reboot, client get TPEOS error

Hi, all
in my tuxedo applicaton, if we use Single Server, Single Queue mode , when reboot any Oracle RAC node, our application is ok, client can get correct result. but if we use MSSQ（Multi Server, Single Queue) , if Oracle RAC node is ok , our application also is ok. but if we reboot any Oracle RAC node, client program can continue run, get correct result, but always get TPEOS error , for this situation， server can get client request, but client can not get server reply, only get TPEOS error.
our enviroment is :
oracle RAC ,10g 10.2.0.4 , two instances ,rac1 rac2, and two DTP services s1 and s2, set s1 and s2 services TAF is basic
tuxedo 10R3 , two nodes ,work in MP model ，use XA access oracle rac database，services have Transaction and not Transaction
OS is linux AS4 U5, 64bits
service program use OCI
can any one encounter this problem ?

Hi, first thanks you
in ULOG file , only have failover information, not any other error message, in client side also has no other error.
not use MSSQ, ubb file about MSSQ config
SERVERS
DEFAULT:
CLOPT="-A "
sinUpdate_server SRVGRP=GROUP11 SRVID=80 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinUpdate_server SRVGRP=GROUP12 SRVID=160 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinCount_server SRVGRP=GROUP11 SRVID=240 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinCount_server SRVGRP=GROUP12 SRVID=320 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinSelect_server SRVGRP=GROUP11 SRVID=360 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinSelect_server SRVGRP=GROUP12 SRVID=400 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinInsert_server SRVGRP=GROUP11 SRVID=520 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinInsert_server SRVGRP=GROUP12 SRVID=560 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinDelete_server SRVGRP=GROUP11 SRVID=600 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinDelete_server SRVGRP=GROUP12 SRVID=640 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinDdl_server SRVGRP=GROUP11 SRVID=700 MIN=5 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinDdl_server SRVGRP=GROUP12 SRVID=740 MIN=5 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
lockselect_server SRVGRP=GROUP11 SRVID=800 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
lockselect_server SRVGRP=GROUP12 SRVID=840 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
#mulup_server SRVGRP=GROUP11 SRVID=1 MIN=2 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
#mulup_server SRVGRP=GROUP12 SRVID=60 MIN=2 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinUpdate_server SRVGRP=GROUP13 SRVID=83 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinUpdate_server SRVGRP=GROUP14 SRVID=164 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinCount_server SRVGRP=GROUP13 SRVID=243 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinCount_server SRVGRP=GROUP14 SRVID=324 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinSelect_server SRVGRP=GROUP13 SRVID=363 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinSelect_server SRVGRP=GROUP14 SRVID=404 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinInsert_server SRVGRP=GROUP13 SRVID=523 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinInsert_server SRVGRP=GROUP14 SRVID=564 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinDelete_server SRVGRP=GROUP13 SRVID=603 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinDelete_server SRVGRP=GROUP14 SRVID=644 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinDdl_server SRVGRP=GROUP13 SRVID=703 MIN=5 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
sinDdl_server SRVGRP=GROUP14 SRVID=744 MIN=5 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
lockselect_server SRVGRP=GROUP13 SRVID=803 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
lockselect_server SRVGRP=GROUP14 SRVID=844 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
#mulup_server SRVGRP=GROUP13 SRVID=13 MIN=2 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
#mulup_server SRVGRP=GROUP14 SRVID=64 MIN=2 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y
WSL SRVGRP=GROUP11 SRVID=1000
CLOPT="-A -- -n//120.3.8.237:7200 -I 60 -T 60 -w WSH -m 50 -M 100 -x 6 -N 3600"
WSL SRVGRP=GROUP12 SRVID=1001
CLOPT="-A -- -n//120.3.8.238:7200 -I 60 -T 60 -w WSH -m 50 -M 100 -x 6 -N 3600"
WSL SRVGRP=GROUP13 SRVID=1003
CLOPT="-A -- -n//120.3.8.237:7203 -I 60 -T 60 -w WSH -m 50 -M 100 -x 6 -N 3600"
WSL SRVGRP=GROUP14 SRVID=1004
CLOPT="-A -- -n//120.3.8.238:7204 -I 60 -T 60 -w WSH -m 50 -M 100 -x 6 -N 3600"
if we use MSSQ ,ubb file about MSSQ config is
*SERVERS
DEFAULT:
CLOPT="-A -p 1,60:1,30"
sinUpdate_server SRVGRP=GROUP11 SRVID=80 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinUpdate11 REPLYQ=Y
sinUpdate_server SRVGRP=GROUP12 SRVID=160 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinUpdate12 REPLYQ=Y
sinCount_server SRVGRP=GROUP11 SRVID=240 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinCount11 REPLYQ=Y
sinCount_server SRVGRP=GROUP12 SRVID=320 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinCount12 REPLYQ=Y
sinSelect_server SRVGRP=GROUP11 SRVID=360 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinSelec11 REPLYQ=Y
sinSelect_server SRVGRP=GROUP12 SRVID=400 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinSelect12 REPLYQ=Y
sinInsert_server SRVGRP=GROUP11 SRVID=520 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinInsert11 REPLYQ=Y
sinInsert_server SRVGRP=GROUP12 SRVID=560 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinInsert12 REPLYQ=Y
sinDelete_server SRVGRP=GROUP11 SRVID=600 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinDelete11 REPLYQ=Y
sinDelete_server SRVGRP=GROUP12 SRVID=640 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinDelete12 REPLYQ=Y
sinDdl_server SRVGRP=GROUP11 SRVID=700 MIN=5 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinDdl11 REPLYQ=Y
sinDdl_server SRVGRP=GROUP12 SRVID=740 MIN=5 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinDdl12 REPLYQ=Y
lockselect_server SRVGRP=GROUP11 SRVID=800 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=lockselect11 REPLYQ=Y
lockselect_server SRVGRP=GROUP12 SRVID=840 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=lockselect12 REPLYQ=Y
#mulup_server SRVGRP=GROUP11 SRVID=1 MIN=2 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=mulup11 REPLYQ=Y
#mulup_server SRVGRP=GROUP12 SRVID=60 MIN=2 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=mulup12 REPLYQ=Y
sinUpdate_server SRVGRP=GROUP13 SRVID=83 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinUpdate13 REPLYQ=Y
sinUpdate_server SRVGRP=GROUP14 SRVID=164 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinUpdate14 REPLYQ=Y
sinCount_server SRVGRP=GROUP13 SRVID=243 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinCount13 REPLYQ=Y
sinCount_server SRVGRP=GROUP14 SRVID=324 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinCount14 REPLYQ=Y
sinSelect_server SRVGRP=GROUP13 SRVID=363 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinSelec13 REPLYQ=Y
sinSelect_server SRVGRP=GROUP14 SRVID=404 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinSelect14 REPLYQ=Y
sinInsert_server SRVGRP=GROUP13 SRVID=523 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinInsert13 REPLYQ=Y
sinInsert_server SRVGRP=GROUP14 SRVID=564 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinInsert14 REPLYQ=Y
sinDelete_server SRVGRP=GROUP13 SRVID=603 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinDelete13 REPLYQ=Y
sinDelete_server SRVGRP=GROUP14 SRVID=644 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinDelete14 REPLYQ=Y
sinDdl_server SRVGRP=GROUP13 SRVID=703 MIN=5 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinDdl13 REPLYQ=Y
sinDdl_server SRVGRP=GROUP14 SRVID=744 MIN=5 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=sinDdl14 REPLYQ=Y
lockselect_server SRVGRP=GROUP13 SRVID=803 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=lockselect13 REPLYQ=Y
lockselect_server SRVGRP=GROUP14 SRVID=844 MIN=10 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=lockselect14 REPLYQ=Y
#mulup_server SRVGRP=GROUP13 SRVID=13 MIN=2 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=mulup13 REPLYQ=Y
#mulup_server SRVGRP=GROUP14 SRVID=64 MIN=2 MAX=30 MAXGEN=10 GRACE=10 RESTART=Y RQADDR=mulup14 REPLYQ=Y
WSL SRVGRP=GROUP11 SRVID=1000
CLOPT="-A -- -n//120.3.8.237:7200 -I 60 -T 60 -w WSH -m 50 -M 100 -x 6 -N 3600"
WSL SRVGRP=GROUP12 SRVID=1001
CLOPT="-A -- -n//120.3.8.238:7200 -I 60 -T 60 -w WSH -m 50 -M 100 -x 6 -N 3600"
WSL SRVGRP=GROUP13 SRVID=1003
CLOPT="-A -- -n//120.3.8.237:7203 -I 60 -T 60 -w WSH -m 50 -M 100 -x 6 -N 3600"
WSL SRVGRP=GROUP14 SRVID=1004
CLOPT="-A -- -n//120.3.8.238:7204 -I 60 -T 60 -w WSH -m 50 -M 100 -x 6 -N 3600"
about above ubb file ,has any error ? or not correct use MSSQ
look forward to you answer,thanks.

Considering shared storage for Oracle RAC 10g

Hi, guys!
My Oracle RAC will be run on VMware ESXI 5.5. So, both 2 nodes and shared storage are on VM. Don't blame for this, I dont have another choice.
I am choosing shared storage for Oracle RAC. I am choosing between NFS and ISCSI server, both can be done in RedHat linux or FreeNAS.
Can u, guys, help me to do the choise?
RedHat or FreeNAS
ISCSI or NFS
Any help will be appreciated.

JohnWatson написал(а):
NFS is really easy. Create your zero-filled files, set the ownership and access modes, and point your asm_diskstring at them. Much simpler than configuring an iSCSI target and initiators, and then messing about with ASMlib or udev.
I recorded a public lecture that (if I remember correctly) describes it here, Oracle ASM Free Tutorial
I will be using OCFS2 as cluster FS. Does it make any difference for NFS vs ISCSI?

Benefits vs Disadvantages of using DNS for Oracle RAC (12c or 11g)

Similar Messages

Maybe you are looking for