Best connection with U-verse Gateway and AirPort Extreme

These past couple of weeks I've been having problems where my AirPort Extreme (connected to my U-verse Gateway) has been randomly rebooting. I had Apple exchange the entire unit along with power cables and AT&T has already switched out the Gateway and it was STILL rebooting. I finally reset both to factory settings and started fresh. I turned off the Wireless on the U-verse Gateway and the Extreme is in Bridge Mode. That is how its always been and luckily fixed the rebooting. I am now having issues with my devices losing connection. For example, on my iPad Air, it'll show it is connected to my Network, but going onto Safari and trying to load a page gives me the "Server Not Responding" error. Issues also happen on not only Apple devices, but on a Wii U where I get connection errors. I HAVE NOT had these problems on my iMac (which is wireless), just on these other devices. I have not messed around with DMZ Plus Mode or changed any settings on the Gateway other than turning off the Wireless. I think it might have something to do with IP Addresses or something, but I am really not sure. If you have this same set-up, are you having these issues or what settings do I need to change? Thank you!
U-verse Gateway Model: 3801 HGV
AirPort Extreme 5th Generation

Ok so I began by reseting both devices and that fixed the majority of the "Server Not Responding" errors. BUT now I'm getting the problem where the AirPort Extreme randomly reboots. Like all of a sudden, all my devices will be disconnected from WiFi. When I go to the router, the Amber light is blinking then goes back to green. This was the issue from the very beginning and it really is very annoying. Can anyone help? If not, I'll try to contact AppleCare and post their solution in case somebody else is having these issues.

Similar Messages

New help with my mac air and airport extreme time capsule dont know how to save to time capsule and use as a external hd

new help with my mac air and airport extreme time capsule dont know how to save to time capsule and use as a external hd would like 2 store my home videos and pictures on the time machine (ONLY) as the MAC AIR has storage space limited space please help. THANK YOU.

See the info here about sharing or using the TC for data.
Q3 http://pondini.org/TM/Time_Capsule.html
It is extremely important you realise.. the Time Capsule was never designed for this.
It is a backup target for Time Machine.. that is the software on the computer that does backups.. it has no direct connection to the Time Capsule.
It has no ability to back itself up.. unlike all other NAS in the market. It is therefore likely one day you will lose all your files unless you seriously work out how to backup.
The TC is slow to spin up the hard disk and fast to spin down. iTunes and iPhoto will continually lose connection to their respective libraries.
iPhoto in particular is easy to corrupt when you move photos over wireless into the library.. once corrupted all is corrupt. A single photo will ruin it all.. so backup is utterly essential.
Time Machine cannot do backups of network drives. ie the TC. You will need a different backup software like CCC. You will then need another target to backup to..

How to connect my iPad, Brother printer, and AirPort Extreme?

How to connect my iPad, Brother printer, and AirPort Extreme?

I don't believe any of the Brother printers are AirPrint-enabled. Is your Brother printer network-ready? That is, does is support either/both a wired or wireless connection or just uses USB to connect?

Is anyone using NETGEAR Push2TV with a MacBook Pro and AirPort Extreme and does it work well for you?

I am interested in buying a NETGEAR Push2TV display TV streamer to use with my MacBook Pro and AirPort Extreme.
I saw on the Netgear site that a Intel Wireless Display/WIFI driver software is required for PC's; do we have this software installed already on our MacBook Pro's? Is any one using this box and does it work well for you, any problems or setup issues?

trying to find out same thing , store said works with new intel processor, My mini dont finding.....

Wireless connection to internet with mac pro tower and airport extreme base station?

Hi, I have an airport extreme base station and a mac pro tower without a airport card. My internet wireless router is a great distance from my computer so I can't connect the base station directly to the router. I've attached the airport extreme base station to the tower via an ethernet cable, the base station seems to be wirelessly connected to the home network but the browser is showing "not connected".
Please help.
Thanks

Shouldn't the Airport base station be able to connect to it wirelessly?
It might be possible, but the Ethernet ports on the AirPort Extreme would not be enabled, even if it did connect to the Thompson' WiFi signal.
As Tesserax notes, among the Apple routers, only the 802.11n versions of the AirPort Express have the capability to "join" a wireless network with the Ethernet port being enabled.

Connect to Linksys Cable Gateway via AirPort Extreme Base Station?

Thank you in advance for any replies.
I have the following new setup:
A G3 Blue tower running OS X 10.4.10 is successfully connected to the internet via a Linksys WCG200 Cable Gateway connected to RCN's cable internet service. The WCG200 unit has wireless capacity though it's connected to the G3 tower via ethernet cable.
A second Mac (G3 iMac DV running OS X 10.4.10) is in another room in the office. I'd like to set it up with internet by wirelessly connecting with the existing WCG200 unit using an Airport Extreme Base Station (AEBS) I've recently acquired. To ensure a smooth process, I reset the AEBS to factory settings and installed the AEBS software (version 4.2) onto the iMac DV. Finally I plugged in the AEBS into the iMac DV using an ethernet cable plugged into the AEBS's WAN port (AirPort Admin Utility advised me to do so).
That's the hardware configuration. Working out the software and configuration details is proving 'niggly'.
First, I used the AirPort Setup Assistant to configure the AEBS. I told it to Set up a new Base Station, then to set it up as connecting to the internet using a Cable modem (the top option of two—the second was to set it up with internet through a LAN). I set up the name and passwords for the Base Station and had the utility configure the AEBS accordingly.
No internet connection occurred. I tried using the Internet Connect utility in the Applications folder, but no button or visible option for connecting via AirPort appeared, as the Setup Guide indicated it should, only a button for a VPN appeared.
I called Apple and asked whether it was even possible to connect to the internet using the AEBS talking wirelessly to the WCG200 unit. A tech told me it could be done by going into the AirPort Administration Utility, going into Configuration, clicking on the WDS tab and inputting the MAC address for the WCG200 unit, then going into the Airport tab and typing in the channel that the WCG200 is using. Note that the WCG200 unit has 3 MAC addresses listed; one each for “modem MAC address,” “WAN-MAN MAC address,” and “WAN-DATA MAC address”. I used the “modem MAC address.
The Apple tech added that it might need further tweaking, but that Apple couldn’t provide this tweaking and that I might check various forums if need be.
I followed the Tech’s advice, at which point the utility informed me that it couldn't use DHCP or NAT with this setup’ and to make sure that the "Distribute IP Addresses" checkbox was deselected under the Internet tab. This I did, but it was already deselected. I told the utility to update the AEBS accordingly, and restarted everything, including the 2 Macs and the WCG200.
Result:
No connection.
Tried it again with the Ethernet plugged into the AEBSs LAN port, still no connection.
Help! Can’t I get the AEBS to even see the WCG200? I know wireless is properly functioning in the WCG200 because another user with a Windows laptop connects to it wirelessly. The Mac Tech also mentioned that this could be relatively easy with an AirPort Express piece of hardware (Card? Base station?) but that it would be difficult with the Airport Extreme Base Station.
At this point we’re willing to spend $100 on getting this up. What would be our best option in terms of equipment, or can connectivity be accomplished with what we have?
Thanks again,
skyheart

skyheart, Welcome to the discussion area!
In theory using WDS would provide what you need.
In reality the Linksys device is not compatible with Apple's WDS and therefore this will not work.

Cannot make backups with timemachine, external harddisk and airport extreme

Hi to everyone,
yesterday i bought me a brandnew airport extreme station. i would like to use it for creating a wifi-network in my flat. besides i would like to connect my external 500GB lacie-harddisk with the airport extreme. in the past i this harddisk was connected with my imac over the usb-port. unfortunately timemachine does not recognize my harddisk. in the timemachine setups i can choose my harddisk but when the backup-process should start, timemachine stops immediately and tells me that the backup-volume wasn't found. whats wrong? does anybody know a solution?
Greets from Germany
Thomas

pantomas wrote:
why is my setup not supported? i read on this page
http://docs.info.apple.com/article.html?path=Mac/10.6/en/15139.html
in that very article, in the second sentence, it clearly says *Time Machine can’t back up to an external disk connected to an AirPort Extreme* ...
so whats my mistake?
a misunderstanding ? say you have 2 Macs on your network. one of them has an external hanging off it. the other Mac could back up to that drive via your network ...
some users, however, successfully back up via an extreme and some don't get it to work. you might be one of 'em.
JGG

Problems with Comcast (Motorola) modem and Airport Extreme

I have a very strange problem which I have been unable to solve, nor able to find a solution on Apple Support or anywhere else by Googling it.
I switched back to Comcast/Xfinity, hooked up the Motorola surfboard SB5120 modem:
My primary Macbook Pro connects to the Internet, but (and this is bizarre!) the AirPort Extreme is flashing yellow with the errors listed as a) no Internet conncetion, and b) no DNS server
All other Wi-Fi devices are *unable* to connect to the Internet; they are connecting to the home network, but nothing else.
I did a "hard" reset of the AE, and setup the home network from scratch, same problems: one Macbook connects, nothing else does.
I have power cycled everything multiple times (even unplugging EVERY cable for 30 minutes, then reconnecting), spent the better part of 6 hours trying tor resolve this.
Any other settings to change?
In AirPort Utility colors:
Green for Internet
Flashing Yellow for AirPort Extreme (errors: a) no Internet conncetion, and b) no DNS server)
Green for AirPort Express
sub-menus:
1) Internet, set to "DHCP", nothing listed for IP Address; the Subnet Mask and Router Address have assigned numberes; the last three windows are empty.
2) Wireless, set to "WPA2 Personal"
3) Network, set to "Off (Bridge Mode)
Any solutions would be most welcomed - the idiot at Comcast was insultingly unhelpful. He said that since I was able to successfully connect to the Internet, and that the modem was successfully pinging back to Comcast, that the problem was with the AirPort Extreme.

Many thanks for your reply. I think number 3) below gets to the crux:
1) The MBP is on my network, for sure, not a neighbor's. I'm doing all of this wirelessly, though tested the modem via Ethernet to make sure the modem was working.
2) I reverted to the Verizon DSL modem, it did a handshake with the AE, and all the computers were successfully connected in seconds.
3) Network set to "Off (Bridge Mode)" is how all the computers are successfully connecting via Verizon, so what am I doing wrong when using Comcast? If I set it to "DHCP and NAT" or "DHCP only" I would have to enter a range of DHCP addresses (Comcast's *might* be 192.168.100.1, but not entirely sure (any help on that - might solve the problem?)
Extreme/Express - that was a mistake. I'm solely using an Extreme for this setup, though I also have an Express, I've temporarily taken it out of the network to try to resolve the issues.
Thanks again!

Connecting Motorola SB6121 Cable Modem and AirPort Extreme

I moved into a new house a couple of days ago so of course the first thing that I needed to do was get the home wireless up and running. My ISP is through Comcast. I purchased my own cable modem (Motorola SB6121) instead of renting and used my own AirPort Extreme as the wireless router.
First, if you're purchasing your own cable modem, you will need to contact your ISP and provide them with the HFC MAC ID on the cable modem. Once you've gone through the motions, you will be able to connect your Mac (in my case Macbook) directly to the modem via ethernet cable and access the internet.
Issue:
When I connected the SB6121 to the AE, I could connect wirelessly to the AE, but I did not have access to the internet. So, basically the SB6121 and the AE were not talking to each other despite being physically connected via ethernet cable.
Solution:
After days of searching for online answers and forums (and trying different solutions) I was able to successfully get everything up and running. Make sure that you have 2 ethernet cables available.
Here are the steps.
I restored my AE to factory settings just to keep everything simple. Here are instructions: http://support.apple.com/kb/HT3728 Once you've restored your AE, make sure that both the AE and the cable modem are unplugged from their power sources.
Plug in the power to the SB6121.
Connect your SB6121 directly to your laptop via Ethernet cable. Test to ensure that you have internet accessibility by going to any website.
Remove the ethernet cable from your laptop and plug it into the "internet in" jack in the back of the AE.
Power up the AE.
Connect your laptop to the back of the AE using ethernet cable #2.
Launch a browser. You should now be able to successfully connect to any website.
Assuming that you reset your AE to factory settings, it should just be broadcasting the generic "Airport Extreme" SSID. Disconnect the ethernet cable and connect using wireless to the SSID. Launch a browser and you should be able to connect to the internet.
You can now use the AirPort Utility to configure the AirPort settings.
I assume that this solution would work with any of the base stations.

I was having the exact same issue tonight. Just purchased the AE Model A1408 and haven't been able to maintain an internet connection on my iMac whenever I tried hooking it up via the Airport Utility application. So after I had the SB6121 connected to the AE and the AE connected to my PC with no luck, I then went to the Network icon in System Preferences. Clicked on "Assist me...". Then clicked on "Diagnostics..." and followed the directions which basically had me first power down the SB6121 modem and power it back up. Then I powered down the AE router and powered it back up. At that point I was now getting an internet connection. I then took my ipad 2 and went to the Wi-Fi settings and noticed it was asking me to setup a network through my AE. I selected that and went through the simple steps to set up the network and password and now it all works. I am a novice so don't ask me why but I now get a green solid light on my AE. I can connect other devices wirelessly. I can still access the internet on my iMac. For whatever reason, using the Airport Utility on the iMac doesn't work in my case and using my ipad to set up the wireless network did the job.

Connecting to internet via windows and airport extreme

I have an imac with a security enabled airport extreme base station. When I startup in Windows via bootcamp and try to connect to the internet I don't know how to enter the network password. Windows sees the network and prompts for a password but my password does not work. Does anyone know what the windows OS is looking for?
Mark

Accessing a Airport Network with a Windows XP PC or laptop (with XP SP2)
http://www.ifelix.co.uk/tech/1011.html
iFelix

Setup Guest Network with OS X Server and Airport Extreme - NEED HELP!

Hi All,
So I have a small business with a Mac Mini Server (10.6.5) and an Airport Extreme. The Airport is handling the routing and DHCP duties, while the Server is handling the DNS. The Airport is pointed to pull DNS from the Server. All internal systems work great accessing the internet and folders on the Server.
I need to setup a Guest network for internet access, so I turned this function on in the Airport Extreme. It sets up fine, but if you connect to that new Guest Network the system hangs trying to open a web page. My thinking is since the Server is the one handling the DNS it is not working for Guest computers since they are not part of our internal network. At least that is my theory, I could be wrong.
With this type of setup what do I need to modify to get this working? Anyone have any ideas?

After trying for days to figure this out I was finally able to get a working solution and I now have my APE providing a guest and main network while using my lion server as the Dsn server for the main network.
The setup is a bit of a hack and does require you to have at least two devices with staticly assigned ip information on the main network but it does allow you to serve dhcp for both networks from the server and make some services available to the guest network such as iTunes remote for parties.
1) delete your custom Dns entries from the Internet settings in the APE and set two dhcp reservations for .2 and .3 (in this case my Mac mini server and my airport express)
2) reduce the dhcp range to only have 2 available IPs (10.0.1.2-10.0.1.3) and save settings
3) on a computer connected to the main network install wireshark and begin sniffing for packets. Connect at least one device to your guest network and look for any packets that have an ip from your guest network (usually 172.16.42.x) once you capture one of these packets expand the vlan information. This should list a vlan ID ( in my case this was 1003. I would suspect this is universal but do not know)
4) on your server open network preferences, click the gear at the bottom and click "manage virtual interfaces", add a vlan that matches the vlan ID from above. Click ok and apply your settings. The vlan interface should get an ip in the guest network range from your APE.
* if you are running lion you will need to install server admin tools before proceeding*
5) open server admin and add the dhcp service. Create an entry for your primary network (ex: 10.0.1.x) make the dhcp range one higher than the settings in step 2 ( ie: 10.0.1.4 to 10.0.1.253) assign this to the physical interface. Make sure this entry has your internal DNA servers
6) add another entry for the guest networks ip range (ex: 172.16.42.x) again set it one ip higher than step 2 ( 172.16.42.4 to 172.16.42.253) save and activate both ranges. Assign this range to the vlan interface. Make sure this entry either contains your isps dns servers or another public dns server. Turn on dhcp.
Because you have now assigned the only two addresses in the APEs pool for your primary network to static entries there will not be any addresses to assign and the APE will not respond to requests. This will allow your server to pick up the work of assigning IPs. As for your guest network, the APE will assign IPs for two host and then stop. Your clients may either get an IP from the APE or the osx server so both should have the same info. Just make sure the two static clients on your main network have the local DNA servers entered manually.

HT204057 new help with my mac air and airport extreme time capsule dont know how to save to time capsule and use as a external hd

i just bought a new mac air and the new airport extreme time capsule im would like to know how to use the time capsule as storage for my pics and videos as the mac are has low storage space can any one walk me through this process?

See the info here about sharing or using the TC for data.
Q3 http://pondini.org/TM/Time_Capsule.html
It is extremely important you realise.. the Time Capsule was never designed for this.
It is a backup target for Time Machine.. that is the software on the computer that does backups.. it has no direct connection to the Time Capsule.
It has no ability to back itself up.. unlike all other NAS in the market. It is therefore likely one day you will lose all your files unless you seriously work out how to backup.
The TC is slow to spin up the hard disk and fast to spin down. iTunes and iPhoto will continually lose connection to their respective libraries.
iPhoto in particular is easy to corrupt when you move photos over wireless into the library.. once corrupted all is corrupt. A single photo will ruin it all.. so backup is utterly essential.
Time Machine cannot do backups of network drives. ie the TC. You will need a different backup software like CCC. You will then need another target to backup to..

Can Anyone help with printing with iphone to lexmark and airport extreme

I don't have a air print compatible printer, and none of the apps available in the appstore are able to print! They recognise the printer, which is an (all-in-one) but nothing prints on giving the print command.
Any thoughts?

did the google for you
http://support.apple.com/kb/HT5209
http://www.apple.com/airplay/
https://discussions.apple.com/thread/4228700?start=0&tstart=0
http://www.youtube.com/watch?v=YCnFfAr1HaM

Best Connection with Airport Express for gaming

Can anyone help me with how I can get the strongest connection from my Airport Express to my PS3 for gaming.
I recently upgraded my old Airport Extreme to an Airport express and everything is great. My internet speeds from the wall are around 90mbps and ruining my laptop and devices from my Airport Express are around 70mbps which I can live with.
When my PS3 is connected it only received around 10mbps which is a massive decrease.
Can anyone help with the best settings for the PS3 to speed it up. My old Airport Extreme used to connected at around 45mbps which was great.
Anyone????????????????

Julie Kruyne wrote:
I am trying to do the exact same thing and am having some difficulties.
It was easier for "WiseJD" because he was using two Apple base stations, instead of your AT&T router.
I select Manual Setup, it just sits there thinking - I can't get into the actual set up.
So you see the Express in AirPort Utility, but when you select it and select "Manual Setup", nothing happens?
When setting up the Express to extend my existing wireless network (AT&T 2WIRE modem and Airport Extreme), do I initially connect the Express, via Ethernet cable, to the modem or the Extreme?
I'll guess that the AT&T device is connected to your broadband connection. Is the 2WIRE device either without Wi-Fi support or is that turned off? How is the Extreme configured, in particular in the AirPort/Wireless panel "Wireless Mode" setting and in the Internet/Internet Connection panel, "Connection Sharing" setting?
If anyone could provide a step by step process on exactly how to set up the Express to extend my existing network, I would be grateful.
I have very little experience with mixed-vendor home networking, but someone should be able to help.

Extending a network with Time Capsule and AirPort Extreme (via Belkin powerline)

Hello -
I've seen many topics about extending wireless networks here, but none seems to resolve the issue I'm having. I currently have a setup where a DSL cable modem is connected to a Time Capsule and I need to extend this network to another room using an AirPort Extreme.
I live in a very old apartment in Brazil and the walls seem to block the signal from one room to another, hence the need to extend it. Since wireless signal is very weak between rooms, I bought a Belkin powerline AV500 so I could connect both Time Capsule and AirPort using the electrical power at home (just installing a regular Ethernet cable between rooms is not an option).
I started with the basics: configure the Time Capsule + DSL as a standalone network, and it works perfectly within it's range. Then I connected the Belking powerline, plugged a MacBook via Ethernet on the other end and still got very good results (actually better speed than expected). Used it for a while with streaming and other network intensive tasks to make sure it could sustain the connection.
Finally, pluggned the AirPort Extreme on the Belking powerline and this is where the problems started. AirPort Utility 6.3.1 only gives me the option of extending a network wirelessly - it doesn't seem to give me the option of extending it via Etherenet (roaming), which is not good in my case. Luckly I had a copy of AirPort Utility 5.6 which seems to do the job (or I thought so), but it's still not working well.
Although I managed to configure both with the same name, it doesn't seem reliable and some devices (the iPhone 5, for example) are unable to connect and end up with a self-asigned IP address. I'm almost sure I'm doing something wrong on the setup, as I've seen a similar setup working before, so if anyone out there has any clue of what can be done, it will be much appreciated.
Attached the screenshots of both Time Capsule and AirPort Extreme configurations.
Thanks a lot,
-TM
AirPort Exteme:
Time Capsule:

Hello JuliaApple. Welcome to the Apple Discussions!
You have several ways to configure both base stations for what you are trying to do.
The simplest would be to configure the Time Capsule (TC) to "join" (AirPort Utility > Manual Setup > Wireless tab > Wireless Mode = Join a wireless network) your existing 802.11n AirPort Extreme Base Station (AEBSn). In this type of configuration the TC would perform as any other wireless client and not perform as a router. It will; however, still allow for both backups and sharing USB devices attached to it.

Best connection with U-verse Gateway and AirPort Extreme

Similar Messages

Maybe you are looking for