Best/correct settings for MSI865PE-LS Bios Vs1.7

I just update bios to Vs 1.7 on my MSI 865PE-LS MB
I would like the best performance settings to run at optimal speed
memory I am using
Dynamic Overclocking: ?
Performance Mode: ?
CPU Ratio Selection: Locked
DRAM Frequency: ?
Spread Spectrum: Disabled
Adjust CPU Bus Clock (Mhz): ?
DDR Clock (Mhz): ?
Adjust AGP/PCI Clock (Mhz): ?
CPU Vcore Adjust: No
CPU VCore: ?
DDR Power Voltage: ?
AGP Power Voltage:?
DRAM Size 1024 MBytes
DRAM Frequency ?
FSB:DRAM ?
CAS# Latency ?
RAS# to CAS# ?
RAS# Precharge ?
Cycle Time (TRAS) ?
# of memory modules 2

Quote
Originally posted by Into Eternity
Dynamic Overclocking: Captain
Performance Mode: Fast
CPU Ratio Selection: Locked
DRAM Frequency: 400
Spread Spectrum: Disabled
Adjust CPU Bus Clock (Mhz): 200/disabled
DDR Clock (Mhz): 400
Adjust AGP/PCI Clock (Mhz): 66/33 default
CPU Vcore Adjust: disabled
CPU VCore: 1.550
DDR Power Voltage: 2.7
AGP Power Voltage:1.5
DRAM Size 1024 MBytes
DRAM Frequency by speed
FSB:DRAM by speed
CAS# Latency by speed
RAS# to CAS# by speed
RAS# Precharge by speed
Cycle Time (TRAS) by speed
# of memory modules 2 - slot 1 and 3
Of course you should try turbo and ultra turbo and faster D.O.T. settings, but I'm taking a guess as to what would work best for you with stability and performance balanced. Post your results or any problems.
thanks (Into Eternity ) your motherboard is different to mine most of the settings would be the same except my bios doesnt have performance mode /IE captain etc
little more info the MSI 865PE-LS setting would still good

Similar Messages

Correct settings for HDV capture

Hi. I'm using Premiere CS5.5. I went on a few forums to get the correct settings for HDV capture.
I can record the footage fine. However I saw a few things which didn't seem right.
After capturing the HDV footage, the file was a .mpeg file. Secondly, the clip was 1 hour and 10 minutes and
it was only 11.3 GB. Does this sound right? A 55 minute .avi file is 11.6GB. I thought a HDV clip would be quite a large size file.
If this dosen't sound right, is there somewhere I could go to, to check that my settings are correct? By the way I'm filming and capturing with a Canon XHA1.
The footage is 1080i. HDV. I've exported it and it looks fine. Just want to make sure I've captured it correctly and to the best quality.
Thanks for your help.

The HDV format was advanced by Sony and others to use the same miniDV tapes used for SD. In fact, your Canon XHAI can record and play either without changing the tape transport speed.
Your observation in relative file sizes is due to the fact that HDV is highly compressed (MPEG), whereas, SD (AVI) is not as highly compressed. This is one of the reasons folks (such as Harm) don't consider HDV to be an edit format, but just a delivery format.
Note that what Harm was saying is symantics--you capture an analog source through a capture card that digitizes it. When you transfer a image file from HDV or SD, it is already digitized, so a bit-to-bit transfer occurs.

What are the correct settings for the Canon 5D mark II in FCP 7 ?

I am shooting full HD at 23s97 fps.. tried making a preset for the Canon but when I import fils FCP always wants to change to appropriate settings for this file type but doesn't tell me what that is...
(latest firmware installed)
Please, can someone provide all the correct settings for me?
And also, why doesn't the camera show up on the desktop/in the menus when attached to the mac? I have ro use EOS utility every time I want to get anything off of the camera... and FCP doesn't see it either. That's just not right - FCP MUST recognise my camera!! : (
Please help - I don't want to start editing until I have the right settings for this footage.
Thanks
Jim

Welcome to the Boards
Not sure what you mean with the following, looks like a word dropped?
I have ro use EOS utility every time I want to get anything off of the camera...
Anyway, some more specs on your system could help point where the issue is. With the new Plug-In by Canon you can Log & Transfer from the Flash Card (not sure how you connected the camera.) Alternatively you could just drag the files in (but make sure to keep all files such as THM in case you use Log and Transfer later.)
Generally it is best to transcode to Pro Res to be able to work with the files in Final Cut. (Log & Transfer should do that, or using Compressor/Mpeg Streamclip.)
It (Final Cut) is probably changing the timeline to match the codec, or depending on your last preset used, just switching things around. In other words if you were editing in DV and had a set up for that, new sequences would default to that and if you try to ad anything else you will get the message.
Take a look at the search over there -> to look for the Canon 5D threads for some more info.
What I would do is just pull one of the clips in to start and look at what the sequence settings are aftr Final Cut changes them for you - they should be fine generally, though you will want to change Codecs to Pro Res.
I like just batch conversion of all my clips from the 5D Markk II and then work from there. (I do not hook up the camera to the computer, just use a card reader.)

Correct settings for DVD

Hi
I wish to know which are the correct settings for making a new project in imovie and then what to do for getting the best quality on DVD. (I use still pictures and video clips with music, transitions and effects)
Thank you so much.

ola
the correct format depends on the format your camera (PAL or NTSC - 4:3 or 16:9) meaning the project format should meet the camera format. pleas note that that format changes in iMovie/iDVD are effective only for new projects and cannot change existing ones. the dvd quality settings depend on the length of your movie and can be set in iDVD under preferences.
my movies are never longer than 30 min. so i set it to faster encoding and check background encoding ... i also tried with best quality once but frankly i can't see the difference
buona suerte & viva la mela

HT1277 i have all the correct settings for my e mail but i can't send for some reason it keeps taking my outgoing server offline

i have all the correct settings for my e mail but i can't send for some reason it keeps taking my outgoing server offline can anyone help

If you can receive mail and your connection to your ISP is otherwise working, but cannot send mail, then your SMTP settings are incorrect; the SMTP server port is wrong, your SSL setting is wrong, or the username or password credentials don't match what the ISP has, or your attempted accesses are being blocked or your ISP SMTP server is offline.
And in general, don't use port 25 for your outbound mail, unless your ISP specifically requires that; these days, that port is best left to communications between mail servers and (usually) not used by any mail clients.

What are the best optimization settings for Logic 9....

Hey guys,
I am running Logic 9 on a Macbook Pro 2.53GHz, Intel Core 2 Duo, 4GB RAM, OSX 10.6.4, with a AK1 soundcard. And I was wondering what the best optimization settings for this setup are?
I have been having a few issues with drop outs in sound during playback, which is also carried over when i bounce the audio. I did some research and found my latency settings needed to be higher, so I set the I/O buffer size to 512. I am also running all samples from the local hdd, I was thinking maybe put the samples on an external drive. I also changed Logic 9 to 64bit mode.
Does anyone know if this is right and anything else I need to do with Logic and/or the AK1??

First, return to 32-bit mode. 64 bit still has some ß-issues and some features that are not working/disabled, and the only perk of 64-bit is that Logic can adress more than 4 GB RAM, which you don't have anyway.
Samples on the startup drive is not a problem, unless you start using really big third party sample libraries, or zillions of EXS instruments. Some of the Logic content insists on residing on the startup disk anyway, better leave that where it is.
If you have an external, use that to store your Logic projects, or, in other words, make it your recording disk (as recordings are stored in the project folder). You do record audio too, I assume? Anyway, if you get an external, make it a FireWire one, not USB. FireWire is much easier on the CPU, and +for audio (and sample-) streaming+ more reliable and faster than USB.
If dropouts you hear during playback also show up in the (offline?) bounce, it is probably not a buffer issue, as the buffer is irrelevant for bouncing offline.
So how many tracks and what kind of tracks in this project? Which plugins and how many instances of them?

What are the best export settings for a HD video in Premier Pro CS4?

Hi!
   I've been having so much trouble with this issue and it's something that continually frustrates my boss. I have a HD video the settings for it are
FPS 23.98
1920 x 1080, then a few lines down it says 1408 x 792
16 bit,
2 channels
48000 Hz
   What should the settings be when I make a new sequence?
             When I look at it in the window in Premiere Pro I have to contantly 'shrink' the image to fit the window, is that something I should be doing or does it indicate the sequence settings are incorrect?
But more importantly what should the export settings be? I exported a 4 minute long video and the size was 1 GB, I know that's too big.
I need to export it without loosing any quality and export another one that meets the Youtube and Vimeo limits on size.
Vimeo is 500 MB per week, sometimes I upload 4 videos per week. I think Youtube you can only upload 500 MB at a time.
I need to get smaller sizes with loosing the least amount of quality possible AND the best export settings for quality, so I guess I have 3 separate questions-
What are the best sequence settings for HD video?
What are the best export settings for HD without loosing any quality?
What are the best export settings for the size to come out around 500 MB with loosing the least amount of quality possible?
Thank You!
http://forums.adobe.com/thread/713070
On the above thread I used the 5th anwer, and it's going to take about 7 hours to export a 4 minute video :/

It Stands for "Coder Decoder."
Your format is like a container for your video file. Certain containers can hold certain codecs and not others. Other containers can hold other codecs. Sometimes different containers can hold the same codecs.
This might be a bad analogy but I'll give it a try.
A coffe cup (container) can hold pretty much any liquid you drink, where a red solo cup (container) won't hold scolding water. So, the coffe cup would be your container of choice most likely because it has the most options for liquids (codecs). But, you might want a red solo cup for just a single crappy beer at a party (a moderate quality streaming video on the web). In that case, you don't need all the optoins of another container.
In Premiere Pro CC H.264 is a Container and the Codec in one option. This has been streamlined for web distrobution of video to be played in browsers without things like Flash or special players.
Were as if you choose the QuickTime Container there are over 40 codec optoins (at least on my machine with additinal ones installed) but you may run into an issue where your browser doesn't support QuickTime playback.
I would say that your container is for compatability with players and your codec is taken into consideration when looking at the quality of the compression.
Yesteraday I wrote a blog entery on Exporting from Premiere Pro and found that the MPEG-4 codec inside of the QuickTime container gave me much richer colors than the H.264 container/codec option.
I posted the link before but here it is:
http://goo.gl/8GZq4i

Best audio settings for mp3?

Hi everyone,
I was wondering what are the best audio settings for an mp3 to import into C4?
Thanks,
Tina

Yes Tina,
I had this issue before. here is what i found:
Record at Sample rate 44100 Hz, 16 bit, high quality publish as MP3
Captivate settings at near CD bitrate 96 kbps,
encoding speed 0,
44.100 KHz encoding frequency

Best export settings for video for web

Can anyone give me some advice on the best export settings for a short video that is to be viewed on the web? I have some short, say 2 minute videos that need to be placed on a website and need a reasonable file size. What would the best Format and Preset options be in Premiere? Would it be helpful to utilize After Effects to reduce file size? Thank you in advance to anyone who has some advice!!

For now, it would be on my own website or a clients website. But there may
be another possibility, I have a client that already has some videos
available for viewing on their website, looks like they are YouTube videos
that play on their site, and there is an option to "Watch on YouTube". So I
guess I would love some recommended export settings for a straightforward
video clip on my website, and if I need to explore the YouTube preset in
Premiere, let me know. Thank you, I really appreciate your answers and
help!!

Best printer settings for the Officejet 8625 for glossy label printing

best printer settings for the Officejet 8625 for glossy label printing. The black does not appear dark black ......just shades of gray

pendavinci
Welcome to the HP Community Forum.
The following might be helpful to resolve the issue:
Printing Labels_Business-Cards_Cards
See the section on Printing and Printing Preferences
Click the Kudos Thumbs-Up to show you appreciate the help.
Click Accept as Solution when the Answer provides a Fix or Workaround!
I am pleased to provide assistance on behalf of HP. I do not work for HP.
Kind Regards,
Dragon-Fur

Best export settings for HD video playback on computer?

I have shot my video on 1080p witha DSLR and edited it in premiere pro. I exported the video in .mp4 format.
Now i imported the video in after effects and added loads of animation. I want to export it to the best quality for playback ON COMPUTER ONLY. Which is the best export settings for this purpose.
I rendered it in .avi and my 12 minute video had a size of 55GB after render and did not play smoothly in the computer.. PLEASE HELP WITH THE BEST SETTINGS for the above purpose.

You messed up. You should NOT have rendered MP4 out of Premiere to use in AE. You're adding compression and quality loss in between stages. BAD video person!
The easiest thing to do would be to import your Premiere project in AE. That way it can use the original footage too. If, for some reason, you can't do that, you should render a lossless file out of Premiere. Speaking of lossless files, that's what you rendered out of AE. This page explains your large AE file issue.
Anyway, take that large file you render out of AE into the Adobe Media Encoder and render out your final compressed file. Either H.264 or WMV should work well for playback.

Best color settings for document view?

Which is best color settings for different document formats with the same color profile?
There are Tiff and Pdf documents with same color profile but look different.
Thanks!

Bridge is file browser with custom preview options, but it's not a pre-press examination application. Just don't use it for that purpose.
P.S. First one is the best as far as I see. I don't like ruined «A» in second example. If you want to get more ballance, you can shift the left side also a bit.

Xcode 3.2.6 best build settings for Mac

Hi!
I'm using Xcode 3.2.6 on Mountain Lion 10.8.5 to create Applescript based applications.
They are tiny utilities that needs more complex UI Applescript can provide.
I''m wondering what's the best build settings for applications aimed to run on Mac OS X
- since 10.6
- non universal binary (no PPC code)
- 64 and 32 bit
Thanks for your help.

Mark,
Now I'm confident about my buids.
red_menace,
Ok. That's what I was affraid about. So if I want to go further, I have to learn AppleScriptObjC.
But the learning curve…
I'm not a developper. Just a graphic designer.
Don't have the time to check out this link, but maybe the solution for a smooth transiton to AppleScriptObjC is there:
http://www.macosxautomation.com/applescript/apps/runner_vanilla.html
Thanks both of you.

Which are the correct settings for gmail in MacBookPro

I want to use mac mail to access my gmail. Can I ? instead of going directly to web to access my gmail.? Which are the correct settings for the incoming and outgoing servers ?

Hi,
Yes. You can absolutely access your Gmail account from within either Mail or Microsoft Outlook for Mac. Make sure, that you have enabled POP/IMAP in your Gmail settings, then follow the instructions here: http://mail.google.com/support/bin/answer.py?hl=en&answer=180188 if you wish to access your account via POP3 instead of IMAP, change the incoming mail server to pop.gmail.com
Regards,
Gábor

Best Video Settings For The iPad.

Hi everyone,
Does anyone know this ? "Best Video Settings For The iPad".
Kindly and in simple terms state the best possible settings to be use when converting videos for the iPad that optimizes the entire screen size/ area without a black borderline around your video. it's rather frustrating to have many technical jargons online without anyone giving real pointers at real values in conversion settings.
Thanks in anticipation.

Kindly and in simple terms state the best possible settings to be use when converting videos for the iPad that optimizes the entire screen size/ area without a black borderline around your video.
It is impossible to answer your question without knowing both the aspect ratio of the source file and your personal preferences for displaying it on a 4:3 iPad screen.
Basically, you have two options here when converting files of one aspect ratio for display on a screen of another aspect. You can distort the original display to "fill" the ipad screen. (E.g., you can make a widescreen movie exactly fill your iPad screen but then people and objects will look tall and skinny.) The other option is to convert at the original aspect ratio and simply use the iPad "zoom" option to force your widescreen movie to fill your 4:3 screen by scaling the height of your movie to fill the screen and allowing the left and right edges of you movie to be cropped from your view. You have no other choices here other than living with the defaulted black areas.

Best/correct settings for MSI865PE-LS Bios Vs1.7

Similar Messages

Maybe you are looking for