Best practice for Book recording vocals...

My wife has written a children's book that we want to record and offer as a downloadable MP3 set. She will do the recording and we have the mic/studio GarageBand all working just fine. My question is what is the best way to make sure that all the tracks for each chapter are equalized the same?
I know that we are trying to record it all the same, but I just wanted to see if there was anyway with GB or some other app to take all the seperate vocal tracks and make them all the same in volume, other than looking at the settings in GB which we don't change as far as input goes...
Hope that is clear and makes sense... I just would like to know what I should do to make it as good as it can be with what we have, then stop worrying about it.
Cheers,
Cory

Hmmm, thanks AppleGuy, that is interesting. I knew that I could create my own presets, but didn't think about this in this way...
So, if I took the first chapter that we did, adjusted it to my liking, ie. reverb to just fill it out a bit, then saved it as a preset, I could then apply this preset to all my other recordings so that they would all have the same properties? I know this wouldn't actually fix the possible increase or decrease of volume from different recording sessions, but it would allow me to make sure they all have the same effects settings, yes?
How do you do this to tracks that are already recorded?
Thanks,

Similar Messages

Best Practice for Recording to HDD's.

I want some answers from some people who have been using Logic for a while and have experience in this topic. I have a 2010 MBP 13" with 1 Firewire 800 port, after looking for a cheap quality interface i purchased a Saffire Pro 14 which has a Firewire 6pin interface and i assume is Firewire 400mbps. The interface also doesn't have an extra Firewire port and the manual says not to "daisy-chain" becuase of latency and CPU spikes. Honestly i haven't noticed any problems with my HDD I/O in Logic, when i skip around it peaks but never any errors. I formatted an old 160GB Sata 1 drive and hooked it up over USB, i noticed that when i "skip" arround or w/e its called it doesn't peak (get red) anymore. I want to know peoples experience with Daisy chaining firewire devices, and using USB HDD's.
When i invest more money, would it be ok to stick with my interface for now and get a Glyph drive and daisy chain my interface on at the end? Should i stick with USB storage? Should i stick with internal 5400RPM drive? Should i upgrade it to a 7200RPM ( my original idea). In I.T. we call it best practices, whats the best practice for storing your audio/logic files on a Mac when running Logic.

Please don't just tell me Firewire is faster than USB.....I'm an I.T. Proffesional (wishing i went to school for recording ) I know how comptuers work, i build them and fix them all day. I want to know from peoples personal experience what they run and their suggestions. Thanks so much!

Best practices for loading apo planning book data to cube for reporting

Hi,
I would like to know whether there are any Best practices for loading apo planning book data to cube for reporting.
I have seen 2 types of Design:
1) The Planning Book Extractor data is Loaded first to the APO BW system within a Cube, and then get transferred to the Actual BW system. Reports are run from the Actual BW system cube.
2) The Planning Book Extractor data is loaded directly to a cube within the Actual BW system.
We do these data loads during evening hours once in a day.
Rgds
Gk

Hi GK,
What I have normally seen is:
1) Data would be extracted from APO Planning Area to APO Cube (FOR BACKUP purpose). Weekly or monthly, depending on how much data change you expect, or how critical it is for business. Backups are mostly monthly for DP.
2) Data extracted from APO planning area directly to DSO of staging layer in BW, and then to BW cubes, for reporting.
For DP monthly, SNP daily
You can also use the option 1 that you mentioned below. In this case, the APO cube is the backup cube, while the BW cube is the one that you could use for reporting, and this BW cube gets data from APO cube.
Benefit in this case is that we have to extract data from Planning Area only once. So, planning area is available for jobs/users for more time. However, backup and reporting extraction are getting mixed in this case, so issues in the flow could impact both the backup and the reporting. We have used this scenario recently, and yet to see the full impact.
Thanks - Pawan

Is there a website or PDF somewhere which discusses best practices for producing a children's picture book? I am mostly interested in requirements for good image format, resolution, etc.

Is there a website or PDF somewhere which discusses best practices for producing a children's picture book? I am mostly interested in requirements for good image format, resolution, etc.

There may be a few links in Apple Support, regarding articles about how to use iBooks Author
and iBooks Store, etc; these would be separated into two general categories by device used.
Since there is an iOS and an OS X version of each, you may have to look to see what Apple
Support says about the one you are interested in; and how far their database goes toward an
answer to your question. Otherwise, a general search engine approach may be necessary.
Not sure if anything along the lines of what you seek would be available in an App.
References to iBooks Author and iBooks Store, etc appear within these two categories in Support:
For Mac OS X:
http://www.apple.com/support/mac-apps/
For iOS:
http://www.apple.com/support/ios/
Appears a community host moved your earlier post into one of the iBooks Author or Store sections
after I'd replied to what otherwise may be a similar post. Not sure if the links to the Discussions area
of iBooks you are interested in, have similar questions or answers by others who'd visited previously.
Is there a website or PDF somewhere which discusses best practices for producing a children's picture book? I am mostly interested in requirements for good image format, resolution, etc.
In my reply to your earlier thread, prior to it being moved, those links to sections of iBooks Author, etc
are posted. You can also find them from the main Apple Support Communities page.
Sorry to not be of much help in this matter.
Good luck & happy computing!

JSF - Best Practice For Using Managed Bean

I want to discuss what is the best practice for managed bean usage, especially using session scope or request scope to build database driven pages
---- Session Bean ----
- In the book Core Java Server Faces, the author mentioned that most of the cases session bean should be used, unless the processing is passed on to other handler. Since JSF can store the state on client side, i think storing everything in session is not a big memory concern. (can some expert confirm this is true?) Session objects are easy to manage and states can be shared across the pages. It can make programming easy.
In the case of a page binded to a resultset, the bean usually helds a java.util.List object for the result, which is intialized in the constructor by query the database first. However, this approach has a problem: when user navigates to other page and comes back, the data is not refreshed. You can of course solve the problem by issuing query everytime in your getXXX method. But you need to be very careful that you don't bind this XXX property too many times. In the case of querying in getXXX, setXXX is also tricky as you don't have a member to set. You usually don't want to persist the resultset changes in the setXXX as the changes may not be final, in stead, you want to handle in the actionlistener (like a save(actionevent)).
I would glad to see your thought on this.
--- Request Bean ---
request bean is initialized everytime a reuqest is made. It sometimes drove me nuts because JSF seems not to be every consistent in updating model values. Suppose you have a page showing parent-children a list of records from database, and you also allow user to change directly on the children. if I hbind the parent to a bean called #{Parent} and you bind the children to ADF table (value="#{Parent.children}" var="rowValue". If I set Parent as a request scope, the setChildren method is never called when I submit the form. Not sure if this is just for ADF or it is JSF problem. But if you change the bean to session scope, everything works fine.
I believe JSF doesn't update the bindings for all component attributes. It only update the input component value binding. Some one please verify this is true.
In many cases, i found request bean is very hard to work with if there are lots of updates. (I have lots of trouble with update the binding value for rendered attributes).
However, request bean is working fine for read only pages and simple binded forms. It definitely frees up memory quicker than session bean.
----- any comments or opinions are welcome!!! ------

I think it should be either Option 2 or Option 3.
Option 2 would be necessary if the bean data depends on some request parameters.
(Example: Getting customer bean for a particular customer id)
Otherwise Option 3 seems the reasonable approach.
But, I am also pondering on this issue. The above are just my initial thoughts.

Best practices for office 365 SHARED CALENDAR for whole school / organization

hi
we need guidance on best practice for setting up SHARED CALENDAR on Office365 exchange server for entire organization (school)of150 staff.
Requirements
+ all staff should have read only / reviewer permissions on calendar
+handful staff should have editor permissions on calendar
+ the calendar should synchronise custom categories and colors
Current Solution
at the moment we have found that a shared mailbox is the best solution because;
- allusers can add the shared mailbox on outlook 2010as additional mailbox as readonly
- all the categories & colors for the calendarare automatically synchronised because the color categories are stored within this mailbox.
- you can edit calendar permissions in outlook to allow some users as "editor" of the calendar.Problem with Current Solution
the problem however is that the users also need to access this...
This topic first appeared in the Spiceworks Community

Hi Aleksei,
I think Inactive mailboxes in Exchange Online is the feature that you want. This feature makes it possible for you to preserve (store and archive) the contents of deleted mailboxes indefinitely.
A mailbox becomes inactive when an In-Place Hold or a
Litigation Hold is placed on the mailbox before the corresponding Office 365 user account is deleted.
But I'm afraid that it might be impossible to "easily share certain folders or even whole mailbox with people in the company". As can been seen from below articles, this only allows administrators, compliance officers, or records managers
to use the In-Place eDiscovery feature in Exchange Online to access and search the contents of an inactive mailbox:
http://technet.microsoft.com/en-us/library/dn144876(v=exchg.150).aspx
http://blogs.technet.com/b/exchange/archive/2013/03/21/preserve-mailbox-data-for-ediscovery-using-inactive-mailboxes-in-exchange-online.aspx
Anyway, this is the forum to discuss questions and feedback for Microsoft Office client. For more details about your question, I would suggest you post in the dedicated forum of
Exchange Online, where you can get more experienced responses:
https://social.technet.microsoft.com/Forums/msonline/en-US/home?forum=onlineservicesexchange
The reason why we recommend posting appropriately is you will get the most qualified pool of respondents, and other partners who read the forums regularly can either share their knowledge or learn from your interaction with us. Thank you for your understanding.
Regards,
Ethan Hua
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs.

Best practices for setting up projects

We recently adopted using Captivate for our WBT modules.
As a former Flash and Director user, I can say it’s
fast and does some great things. Doesn’t play so nice with
others on different occasions, but I’m learning. This forum
has been a great source for search and read on specific topics.
I’m trying to understand best practices for using this
product. We’ve had some problems with file size and
incorporating audio and video into our projects. Fortunately, the
forum has helped a lot with that. What I haven’t found a lot
of information on is good or better ways to set up individual
files, use multiple files and publish projects. We’ve decided
to go the route of putting standalones on our Intranet. My gut says
yuck, but for our situation I have yet to find a better way.
My question for discussion, then is: what are some best
practices for setting up individual files, using multiple files and
publishing projects? Any references or input on this would be
appreciated.

Hi,
Here are some of my suggestions:
1) Set up a style guide for all your standard slides. Eg.
Title slide, Index slide, chapter slide, end slide, screen capture,
non-screen capture, quizzes etc. This makes life a lot easier.
2) Create your own buttons and captions. The standard ones
are pretty ordinary, and it's hard to get a slick looking style
happening with the standard captions. They are pretty easy to
create (search for add print button to learn how to create
buttons). There should instructions on how to customise captions
somewhere on this forum. Customising means that you can also use
words, symbols, colours unique to your organisation.
3) Google elearning providers. Most use captivate and will
allow you to open samples or temporarily view selected modules.
This will give you great insight on what not to do and some good
ideas on what works well.
4) Timings: Using the above research, I got others to
complete the sample modules to get a feel for timings. The results
were clear, 10 mins good, 15 mins okay, 20 mins kind of okay, 30
mins bad, bad, bad. It's truly better to have a learner complete
2-3 short modules in 30 mins than one big monster. The other
benefit is that shorter files equal smaller size.
5) Narration: It's best to narrate each slide individually
(particularly for screen capture slides). You are more likely to
get it right on the first take, it's easier to edit and you don't
have to re-record the whole thing if you need to update it in
future. To get a slicker effect, use at least two voices: one male,
one female and use slightly different accents.
6) Screen capture slides: If you are recording filling out
long window based databse pages where the compulsory fields are
marked (eg. with a red asterisk) - you don't need to show how to
fill out every field. It's much easier for the learner (and you) to
show how to fill out the first few fields, then fade the screen
capture out, fade the end of the form in with the instructions on
what to do next. This will reduce your file size. In one of my
forms, this meant the removal of about 18 slides!
7) Auto captions: they are verbose (eg. 'Click on Print
Button' instead of 'Click Print'; 'Select the Print Preview item'
instead of 'Select Print Preview'). You have to edit them.
8) PC training syntax: Buttons and hyperlinks should normally
be 'click'; selections from drop down boxes or file lists are
normally 'select': Captivate sometimes mixes them up. Instructions
should always be written in the correct order: eg. Good: Click
'File', Select 'Print Preview'; Bad: Select 'Print Preview' from
the 'File Menu'. Button names, hyperlinks, selections are normally
written in bold
9) Instruction syntax: should always be written in an active
voice: eg. 'Click Options to open the printer menu' instead of
'When the Options button is clicked on, the printer menu will open'
10) Break all modules into chapters. Frame each chapter with
a chapter slide. It's also a good idea to show the Index page
before each chapter slide with a progress indicator (I use an
animated arrow to flash next to the name of the next chapter), I
use a start button rather a 'next' button for the start of each
chapter. You should always have a module overview with the purpose
of the course and a summary slide which states what was covered and
they have complete the module.
11) Put a transparent click button somewhere on each slide.
Set the properties of the click box to take the learner back to the
start of the current chapter by pressing F2. This allows them to
jump back to the start of their chapter at any time. You can also
do a similar thing on the index pages which jumps them to another
chapter.
12) Recording video capture: best to do it at normal speed
and be concious of where your mouse is. Minimise your clicks. Most
people (until they start working with captivate) are sloppy with
their mouse and you end up with lots of unnecessarily slides that
you have to delete out. The speed will default to how you recorded
it and this will reduce the amount of time you spend on changing
timings.
13) Captions: My rule of thumb is minimum of 4 seconds - and
longer depending on the amount of words. Eg. Click 'Print Preview'
is 4 seconds, a paragraph is longer. If you creating knowledge
based modules, make the timing long (eg. 2-3 minutes) and put in a
next button so that the learner can click when they are ready.
Also, narration means the slides will normally be slightly longer.
14) Be creative: Capitvate is desk bound. There are some
learners that just don't respond no matter how interactive
Captivate can be. Incorporate non-captivate and desk free
activities. Eg. As part of our OHS module, there is an activity
where the learner has to print off the floor plan, and then wander
around the floor marking on th emap key items such as: fire exits;
first aid kit, broom and mop cupboard, stationary cupboard, etc.
Good luck!

SAP Best Practice for Document Type./Item category/Acc assignment cat.

What is the Best Practice for the document Type & Item category
I want to use NB - Item category - B & K ( Blanket PO) , D ( Service) and T( Text) .
Is sap recommends to use FO Only for the Blanket Purchase Order.
We want to use service contract (with / without service entry sheet) for all our services.
We want to buy asset for our office equipments .
Which is the best one to use NB or FO ?
Please give me any OSS notes or reference for this
Thanks
Nick

Thank you very much for your response.
I hope I can provide some clarity on how the accounting needs to be handle per FERC Regulations. The G/L balance on the utility that is selling the assets will be in the following accounts (standard accounts across all FERC Regulated Utilities):
101 - Acquisition Value for the assets
108 - Accumulated Depreciation Value for the assets
For an example, there is Debit $60,000,000 in FERC Account 101 and a credit $30,000,000 in FERC Account 108. When the purchase occurs, the net book value for the asset will be on our G/L in FERC Account 102. Once we have FERC Approval to acquire the plant assets, we will need to enter the Acquisition Value and associated Accumulated Depreciation onto our G/L to FERC Account 101 and FERC Account 108 respectively with an offset to FERC Account 102.
The method that I came up with is to purchase the NBV of the assets to a clearing account. I then set up account assignments that will track the Acquisition Value and respective Accumulated Depreciation for each asset that is being purchased. I load the respective asset values using t-code AS91 and then make an entry to the 2 respective accounts with the offset against the clearing account using t-code OASV. Once my company receives FERC approval, I will transfer the asset to new assets that has the account assignments for FERC Account 101 and FERC Account 108 using t-code ABUMN or FB01.

Best practice for external but secure access to internal data?

We need external customers/vendors/partners to access some of our company data (view/add/edit). It’s not so easy as to segment out those databases/tables/records from other existing (and put separate database(s) in the DMZ where our server is). Our
current solution is to have a 1433 hole from web server into our database server. The user credentials are not in any sort of web.config but rather compiled in our DLLs, and that SQL login has read/write access to a very limited number of databases.
Our security group says this is still not secure, but how else are we to do it? Even if a web service, there still has to be a hole in somewhere. Any standard best practice for this?
Thanks.

Security is mainly about mitigation rather than 100% secure, "We have unknown unknowns". The component needs to talk to SQL Server. You could continue to use http to talk to SQL Server, perhaps even get SOAP Transactions working but personally
I'd have more worries about using such a 'less trodden' path since that is exactly the areas where more security problems are discovered. I don't know about your specific design issues so there might be even more ways to mitigate the risk but in general you're
using a DMZ as a decent way to mitigate risk. I would recommend asking your security team what they'd deem acceptable.
http://pauliom.wordpress.com

Best practice for reinstalling anti virus on reinstalling windows

Best practice for reinstalling anti virus after formatting drive and reinstalling windows No anti virus disc.
Hasty

Hello,
I'd ask in the Windows forum on Microsoft Community.
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog:http://unlockpowershell.wordpress.com
My Book:Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C40686F746D61696C2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}})

What are best practice for packaging and deploying j2EE apps to iAS?

We've been running a set of J2EE applications on a pair of iAS SP1b for about a year and it has been quite stable.
Recently however we have had a number of LDAP issues, particularly when registering and unregistering applications (registering ear files sometimes fails 1st time but may work 2nd time). Also We've noticed very occasionally that old versions of classes sometimes find their way onto our machines.
What is considered to be best practice in terms of packaging and deployment, specifically:
1) Packaging - using the deployTool that comes with iAS6 SP1b to package is a big manual task, especially when you have 200+ jsp files. Are people out there using this or are they scripting it with a build tool such as Ant?
2) Deploying an existing application to multiple iAS's. Are you guys unregistering old application then reregistering new application? Are you shutting down iAS whilst doing the deployment?
3) Deploying ear files can take 5 to 10 mins, is this normal?
4) In a clustered scenario where HTTPSession is shared what are the consequences of doing deployments to data stored in session?
thanks in asvance for your replies
Owen

You may want to consider upgrading your application server environment to a newer service pack. There are numerous enhancements involving the deployment tool and run time layout of your application that make clear where you're application is loading its files from.
If you've at a long running application server environment, with lots of deployments under your belt, you might start to notice slow downs in deployment and kjs start time. Generally this is due to garbage collecting in your iAS registry.
You can do several things to resolve this. The most complete solution is to reinstall the application server. This will guarantee a clean ldap registry. Of course you've got to restablish your configurations and redeploy your applications. When done, backup your application server install space with the application server and directory server off. You can use this backup to return to a known configuation at some future time.
For the second method: <B>BE CAREFUL - BACKUP FIRST</B>
There is a more exhaustive solution that involves examining your deployed components to determine the active GUIDS. You then search the NameTrans section of the registry searching for Applogic Servlet *, and Bean * entries that represent your previously deployed components but are represented in the set of deployed GUIDs. Record these older GUIDs, remove them from ClassImp and ClassDef. Finally remove the older entries from NameTrans.
Best practices for deployment depend on your particular environmental needs. Many people utilize ANT as a build tool. In later versions of the application server, complete ANT scripts are included that address compiling, assembly and deployment. Ant 1.4 includes iAS specific targets and general J2EE targets. There are iAS specific targets that can be utilized with the 1.3 version. Specialized build targets are not required however to deploy to iAS.
Newer versions of the deployment tool allow you to specify that JSPs are not to be registered automatically. This can be significant if deployment times lag. Registered JSP's however benefit more fully from the services that iAS offers.
2) In general it is better to undeploy then redeploy. However, if you know that you're not changing GUIDs, recreating an existing application with new GUIDs, or removing registered components, you may avoid the undeploy phase.
If you shut down the KJS processes during deployment you can eliminate some addition workload on the LDAP server which really gets pounded during deployment. This is because the KJS processes detect changes and do registry loads to repopulate their caches. This can happen many times during a deployment and does not provide any benefit.
3) Deploying can be a lengthy process. There have been improvements in that performance from service pack to service pack but unfortunately you wont see dramatic drops in deployment times.
One thing you can do to reduce deployment times is to understand the type of deployment. If you have not manipulated your deployment descriptors in any way, then there is no need to deploy. Simply drop your newer bits in to the run time space of the application server. In later service packs this means exploding the package (ear,war, or jar) in to the appropriate subdirectory of the APPS directory.
4) If you've changed the classes of objects that have been placed in HTTPSession, you may find that you can no longer utilize those objects. For that reason, it is suggested that objects placed in session be kept as simple as possible in order to minimize this effect. In general however, is not a good idea to change a web application during the life span of a session.

Best practice for PK and indexes?

Dear All,
What is the best practice for making Primary Key and indexes? Should we keep them in the same tablespace as table or should we create a seperate tableapce for all indexes and Primary Key? Please note I am talking about a table that has 21milion rows at the moment and increasing 10k to 20k rows daily. This table is also heavily involved in daily reports and causing slow performance. Currently the complete table with all associated objects such as indexes and PK is stored in one seperate tablespace. If my way is right then please advise me how can I improve the performance of retrival or DML operation on this table?
Thanks in advance..
Zia Shareef

Well, thanks for valueable advices... I am using Oracle 8i and let me tell you exact problem...
My billing database has two major tables having almost 21 millions rows each... one has collection data and other one for invoices... many reports are showing the data with the joining of Customer + Collection + Invoices tables.
There are 5 common fields in between invoices(reading) and collection tables
YEAR, MONTH, AREA_CODE, CONS_CODE, BILL_TYPE(adtl)
My one of batch process has following update and it is VERY VERY SLOW:
UPDATE reading r
SET bamount (SELECT sum(camount)
FROM collection cl
WHERE r.ryear = cl.byear
AND r.rmonth = cl.bmonth
AND r.area_code = cl.area_code
AND r.cons_code = cl.cons_code
AND r.adtl = cl.adtl)
WHERE area_code = 1
tentatively area_code(1) is having 20,000 consumers
each consuemr may have 72 invoices and against these invoices it may have 200 rows in collection tables (system have provision to record partial payment against one invoice)
NOTE: Please note presently my process is based on cursors so the above query runs for one consumer at one time but just for giving an idea I have made it for whole area.
Mr. Yingkuan, can you please tell me how can I check that the table' statistics is not current and how can I make it current. Is it really effect performance?

Best practice for a deplomyent (EAR containing WAR/EJB) in a productive environment

Hi there,
I'm looking for some hints regarding to the best practice deployment in a productive
environment (currently we are not using a WLS-cluster);
We are using ANT for buildung, packaging and (dynamic) deployment (via weblogic.Deployer)
on the development environment and this works fine (in the meantime);
For my point of view, I would like to prefere this kind of Deploment not only
for the development, also for the productive system.
But I found some hints in some books, and this guys prefere the static deployment
for the p-system.
My question now:
Could anybody provide me with some links to some whitepapers regarding best practice
for a deployment into a p-system ??
What is your experiance with the new two-phase-deploment coming up with WLS 7.0
Is it really a good idea to use the static deployment (what is the advantage of
this kind of deployment ???
THX in advanced
-Martin

Hi Siva,
What best practise are you looking for ? If you can be specific on your question we could provide appropriate response.
From my basis experience some of the best practices.
1) Productive landscape should have high availability to business. For this you may setup DR or HA or both.
2) It should have backup configured for which restore has been already tested
3) It should have all the monitoring setup viz application, OS and DB
4) Productive client should not be modifiable
5) Users in Production landscape should have appropriate authorization based on SOD. There should not be any SOD conflicts
6) Transport to Production should be highly controlled. Any transport to Production should be moved only with appropriate Change Board approvals.
7) Relevant Database and OS security parameters should be tested before golive and enabled
8) Pre-Golive , Post Golive should have been performed on Production system
9) EWA should be configured atleast for Production system
10) Production system availability using DR should have been tested
Hope this helps.
Regards,
Deepak Kori

Best practice for remote topic subscription with HA

I'd like to create an orchestrator EJB, in cluster A, that must persist some data to a database of record and then publish a business event to a topic. I have two durable subscribers, MDBs on clusters B & C, that need to receive the events and perform some persistence on their side.
          I'd like HA so that a failure in any managed server would not interrupt the system. I can live with at least once delivery, but at the same time I'd like to minimize the amount of redundant message processing.
          The documentation gets a little convoluted when dealing with clustering. What is the best practice for accomplishing this task? Has anyone successfully implemented a similar solution?
          I'm using Weblogic 8.1 SP5, but I wouldn't mind hearing solutions for later versions as well.

A managed server failure makes that server's JMS servers unavailable, which, in turn, makes the JMS server's messages unavailable until the either (A) the JMS server is migrated or (B) the managed server is restarted.
          For more discussion, see my post today on topic "distributed destinations failover - can't access messages from other node". Also, you might be interested in the circa 8.1 migration white-paper on dev2dev: http://dev2dev.bea.com/pub/a/2004/05/ClusteredJMS.html
          Tom

What is the best practice for inserting (unique) rows into a table containing key columns constraint where source may contain duplicate (already existing) rows?

My final data table contains a two key columns unique key constraint. I insert data into this table from a daily capture table (which also contains the two columns that make up the key in the final data table but are not constrained
(not unique) in the daily capture table). I don't want to insert rows from daily capture which already exists in final data table (based on the two key columns). Currently, what I do is to select * into a #temp table from the join
of daily capture and final data tables on these two key columns. Then I delete the rows in the daily capture table which match the #temp table. Then I insert the remaining rows from daily capture into the final data table.
Would it be possible to simplify this process by using an Instead Of trigger in the final table and just insert directly from the daily capture table? How would this look?
What is the best practice for inserting unique (new) rows and ignoring duplicate rows (rows that already exist in both the daily capture and final data tables) in my particular operation?
Rich P

Please follow basic Netiquette and post the DDL we need to answer this. Follow industry and ANSI/ISO standards in your data. You should follow ISO-11179 rules for naming data elements. You should follow ISO-8601 rules for displaying temporal data. We need
to know the data types, keys and constraints on the table. Avoid dialect in favor of ANSI/ISO Standard SQL. And you need to read and download the PDF for:
https://www.simple-talk.com/books/sql-books/119-sql-code-smells/
>> My final data table contains a two key columns unique key constraint. [unh? one two-column key or two one column keys? Sure wish you posted DDL] I insert data into this table from a daily capture table (which also contains the two columns that make
up the key in the final data table but are not constrained (not unique) in the daily capture table). <<
Then the "capture table" is not a table at all! Remember the fist day of your RDBMS class? A table has to have a key. You need to fix this error. What ETL tool do you use?
>> I don't want to insert rows from daily capture which already exists in final data table (based on the two key columns). <<
MERGE statement; Google it. And do not use temp tables.
--CELKO-- Books in Celko Series for Morgan-Kaufmann Publishing: Analytics and OLAP in SQL / Data and Databases: Concepts in Practice Data / Measurements and Standards in SQL SQL for Smarties / SQL Programming Style / SQL Puzzles and Answers / Thinking
in Sets / Trees and Hierarchies in SQL

Best practice for Book recording vocals...

Similar Messages

Maybe you are looking for