Best practice power setting when doing a Site Survey for VOIP

Hi Team,
Can someone please confirm or correct me. When doing a Wireless Active Site Survey for Cisco VOIP, I should be setting the Test AP to local power of 14, which is 25mW? Is this correct, or should it be another value? I asked the customer for the power of their weakest client and they do not know, but they claim there's a high probably that they will go with Cisco VOIP clients.
Thanks...

When you check the signal coverage, make sure the AP's radio transmit power does not use a transmit power greater than what the client devices can support. For example, by default, the Cisco Unified Wireless IP Phone 7925G uses the highest available transmit power by default (17 dBm / 50 mW for 2.4 GHz and 16 dBm / 40 mW for 5 GHz). It is possible to have a survey report that shows good coverage in all areas; however, if you have APs that operate at the highest transmit power, you might still experience uplink issues where the client devices do not support the same transmit power. For areas where there is deficient coverage, and you increase the AP transmit power to levels that the client devices cannot support, this only increases coverage on the downlink.
Link for the same :-
http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/116057-site-survey-guidelines-wlan-00.html

Similar Messages

Site survey for voip cutover

need a template to conduct a site survey to determine phone lines, extentions, phone features, etc

The following book has some useful questionnaires.
http://www.ciscopress.com/bookstore/product.asp?isbn=1587051575
Hope this helps. If so, please rate the post.
Brandon

HT2534 Best practice in setting up an iTunes Connect account for my business

I have a personal iTunes account but I want to create a separate business account so that I can sign up for iTunes Connect to create books? Any suggestions? Should I create a new iTune account or not. I would like to keep them separate but I don't need any of the other iTunes offereings such as music, etc. I just want an account so that I can open the ITunes Connect. Has anyone done that - with or without separating it from their personal. Actually, I have two businesses which deal with publishing so I would probably want Separate iTunes Connect accounts for both of them. Help?

Hi Andy,
Unfortunately, your registration experience seems to be fairly common. It tooks about 8 business days for us to receive our final approval.
One thing to confirm - about a day or two after submitting the original request, I received an email stating that I needed to review and execute the iTunes U Service agreement. Did you receive that email? It took about another 6 business days after that to complete the process.
Another thing to check - did you designate someone else as your Site Manager? That is the person that will recieve the final approval notice and the steps to initialize the site.
Ken

Best practice to set up the user authorization

Dear expert,
I have a question regarding the user authorization access. I've attend the BOE training but I'm still blur in term of user authorization planning. Currently, I have around 50 named users that need to access the BOE server. But the certain user will be restricted to access to certain folders or reports. May I know what is the best practice to set up the user authorization access? Should I set up first in the development machine and once its firm, then I migrate it to production machine..or is there any steps that I need to follow...?
Really appreciate if you can let me know on what should I look into first before set up the authorization. Is there any doccument that I can referring to..?
Thanks & Regards,
-Syahida-

Create User Group for each folder (for eg. Sales/Marketing etc) and also based on the type of access you want to provide.
Like Sales VOD/ Sales View/Sales Schedule, and add users to the User Group based on the type of rights you want to provide them. Then add the User Group to respective report folders.
First deploy it in the Development environment, once you have everything finalized then you can replicate the same to QA and Prod environment by migration. Also make sure that in Development environment developers will have full control to develop/add reports to folders, you have to restrict that in QA & Prod environment.

When does your site become "live'?

We are new to iTunes U - have been approved and now uploading media onto the site. When does your site go live to the public? Is there an approval process from Apple?
What is the process?
Thanks.
Janice
SUNY Rockland

This is my understanding.
Your offerings are immediately available via the URL that looks like https://deimos.apple.com/WebObjects/Core.woa/Browse/aug.edu - the last part is obviously the part that changes with each institution.
The listing on the iTunes University page within the iTunes Store is a different story. Apple seems to prefer to wait until a site is fully developed to have them listed there. Once you feel you are ready, I've been told to contact my Apple rep and let them know. If they think you still need more offerings or changes to your site before it shows up in their area, they'll let you know.

When does java deallocate memory for objects;

um i'm working on a midp application that is very memory consuming. i would like to optimise it and make it just the oposite of what it is. now i would like to know when does java dellocate memory for an object, is it when it can find no more references to that object? or some other time, well i know its not when it can find no more references to that object because i've already tried that.
or to make things simpler is there any explicit way to make java deallocate memory for a specific object, like if i have a thread, which is executing a while loop, and i want java to end the thread and free its memory. is there any way to do this?

I happen to have quite some J2ME experience and it's not overly wise to count on extensive garbage collection. The garbage collector in limited device VMs isnt as advanced as it's big brothers. Try to avoid excessive object allocation and reuse instances whenever possible.
As for garbage collection, objects will be garbage collected if they can no longer be reached by any of the active application threads and if the garbage collectors deems it necessary to collect garbage, which will probably be when free heap memory becomes sparse or when there's some idle time in your application.

Any Best Practices (i.e. DOs and Don'ts) for source to target MAPPINGs?

Hi Experts,
Any Best Practices (i.e. DOs and Don'ts) for source to target MAPPINGs?
I will appreciate any hints on this.
Thanks

Hi,
I am assuming that you are asking about transformation mapping between source and target..
1) One to One mapping
2)Avoid using complex calculations
3) if any calculations required use routine instead of formulas
4)if possible avoid Using field routine (you can do start or end routine )
5)Do not map unwanted fields ( unnecessary process time,database occupant, also problem while activation of DSO data )
6)Avoid using master data read mapping option instead you can use routine to fetch the master data
7) no need of using infosurce
8)Use standard time conversions for time fields
Generally these things we need to consider while mapping..
Regards,
Satya

When does converter program begin for me?

I purchased the $19.99 annual package to convert .pdf to Word and Excel. Did so on Friday, February 3. How long before the program works for me? Larry Walker, Pensacola, FL

Newbie. Should have marked this to you.
7. Feb 13, 2012 3:48 PM (in response to Larrywalker2007)
Re: When does converter program begin for me?
I have same issue in Atlanta. Purchased Feb 13. Confirmed that same email is being used as when subscribed. (No luck, even when clicking on link in "Verify your email" from Adobe). It shows that I have a paid subscription in "My Subscriptions".
Ted in Atlanta

Site survey for location based services

Hi Experts ,
Wht are the paramenters I need to concentrate while doing the site survey that incldes the requirement of location services?
Thanks,
Regards,
Vijay.

Location-based services:
WLAN location-based services requires that access points are placed in such a
fashion that the Active RFID tags and 802.11 clients ar
e surrounded by access points for ultimate optimization.
(This is a different access point placement strategy than data and voice WLAN only networks). If you are
surveying for location based services, acce
ss point placement is done differently. For more information on
deploying location based services, refer to the Cisco 2700 Series Wireless Location Appliance Deployment
Guide available at Cisco.com.
http://www.cisco.com/en/US/docs/wireless/technology/vowlan/troubleshooting/8_Site_Survey_RF_Design_Valid.html

Wireless Site-Survey for High Density Environment

Hi,
I have done many Wireless SIte-Surveys in my career. But this will the first time, I am going to do a Site-Survey for High Density environment (School with Byod 1:1 design).
Currently, the school has a Wireless network in place. The current wireless design includes 3502 APs, 5508 WLC and Cisco Prime. The customer has issues with sufficient bandwidth in classrooms which limiting the students and teachers to access the learning content.
It is understood that there was no initial Site-Survey conducted, the AP positioning was made based on their knowledge.
Now, I am not sure as how to conduct the Survey here?
Do I need to conduct an Active Survey by connecting to the existing Wireless Network in the School? Or just passive Survey will be enough to determine the exact issues with the current design and provide the recommendations?
I have gone through the Cisco High Density design and white papers to start with.
Thanks,
CJ

Before you do the site survey, I'd do the initial breakdown of the LAN.
1. What kind of switch ports are we talking about?
2. Are the APs connected AND negotiated to 1 Gbps ports?
3. What is/are the switch uplinks? 100 Mbps, 1- or 10- Gbps, Etherchannel?
4. Line errors on the links between the AP and the switch, uplinks and the link between the WLC and the switches?
5. WLC link? How many are used? Are they LAG or not?
6. Configuration of the WLC must be checked.
Once you've checked these do I start talking about wireless:
1. What problems are the staff/students experiencing?
2. How many APs to a classroom? How big is the class?
3. Determine what kind of traffic are each class trying to push?
4. Where are the APs located in relations to the staff/student?
5. Verify co-channel interferrence. I know they have 3502 but I've seen people disable CleanAir.
6. Verify what kind of NIC cards are used and whether drivers have been updated or not.
I'm in the middle of improving our wireless coverage in >98 schools. This means I am now deploying 1 AP per classroom. In areas where the students/staff converge, I put additional APs (both indoors and outdoors).

What is the best practice to set Captivate variables from Get (less ideal) and Post (more ideal)?

We are trying to set a couple of variables in Captivate 7 by posting the information from a URL. Is there a best practice for doing this, or does it require a custom JS or other call in order to do this?
Essentially, we want to pass three variables from a URl to named variables in a Captivate 7 swf so that the information can be drawn from a database, and does not need to be entered by the user.
Suggestions, thoughts, pointers to where we may be able to find this information - all would be greatly appreciated!

Not sure how Captivate treats FlashVars internally, but the native html template includes a script to read URL parameters:
var strURLFull = window.document.location.toString();
var intTemp = strURLFull.indexOf("?");
var strURLParams = "";
then:
if(strURLParams != "")
so.addVariable("flashvars",strURLParams);
It also has a script to add variables but you'd have to parse the variables first first to use it:
so.addVariable("variable1", "value1");

RMBP - high frequency/power noise when doing file operations?

Hi,
I noticed today that my new rMBP is emitting some strange high pitched noise, especially when doing heavy files operations like spotlight indexing or startup of the computer. It's louder and more prominent when I connect the AC adapter. It sounds like some power interference, a bit like some broken chargers do or Iphone 4s when transmitting 3G data.
It's not very loud but I can hear it clearly, when sitting in a silent room, even without closing my ear to the Macbook.
Has anybody noticed that or can advise something? Is that normal with those machines or some issue that has to be fixed? I really don't want to return it, as it is perfect otherwise...
Thanks in advance for feedback.

here is the link to a sample of that noise. Please listen from 15 second:
http://wikisend.com/download/438696/Memo.m4a

What is "best practice" to set up and configure a Mac Mini server with dual 1 TB drives, using RAID 1?

I have been handed a new, out of the box, Mac Mini server. Has two 1 TB drives in it. Contractor suggested RAID 1 for the set up. I have done some research
and found out that in creating the software RAID, this takes away the recovery partition, so I have been reading up on how to create a recovery "disk" using a thumb drive. this part of the operation I am comfortable with, but there are other issues/concerns that I have.
Basically, what is the "best practice" to setup the Mini, configure the RAID and then start the server. I am assuming the steps would be something like this:
1) start up the Mini and run through the normal Maverick setup/config - keep it plain and vanilla
2) grab a copy of the Server app and store it offline in a safe place
3) perform the RAID configuration / reinstall of OS X Maverick using the recovery tools
4) copy down and start the server app
This might be considered a very simplified version of this article (http://support.apple.com/kb/HT4886 - Mac mini server (Late 2012 and Mid 2011): How to install OS X Server on a software RAID volume), with the biggest difference being I grab a copy of the Server App off of the mini before I reinstall, since I did not purchase it from the App store, but rather it came with the mini.
Is there a best practice / how-to tutorial somewhere that I can follow/learn from? Am I on the right track or headed for a train wreck?
thanks in advance

I think this article will answer your question. Hope this helps: http://wisebyte.blogspot.com/2014/01/best-configuration-for-mac-mini-server.html

Oracle Best Practices in 10g When Disabling NUMA

We have both Linux and Solaris 10 DB servers running 10g on them with NUMA. What is Oracle's best practice for dealing with NUMA in hardware when it can be disabled?

user10387007 wrote:
We have both Linux and Solaris 10 DB servers running 10g on them with NUMA. What is Oracle's best practice for dealing with NUMA in hardware when it can be disabled?How are you using NUMA (Non Uniformed Memory Access)?
NUMA can be implemented at CPU level - in which case CPU affinity becomes important. NUMA can be used across an Interconnect (e.g. SCSI over RDMA protocol).
So it depends on what you mean by NUMA and how you are using it (and whether or not it is used by the Oracle s/w stack itself).

Best Practice AV set up on SAP Servers

Hi,
Has anyone come across or aware of any best practice guidelines for AV setup on SAP servers, for example, which files/drives should you exclude and configuration tuning/reg-edits required. We have McAfee as our standard AV and we do use the HIPS component.
Thanks,
Martin

My best advise is:
Don't run AV on a database server but rather reconfigure the local/a firewall so that only those ports are open which are necessary to run the SAP application.
Excluding files may help a bit but neverless, as soon as the AV scanner is installed it will hook up to the filesystem layer and slowing down (maybe not significantly) I/O. I've seen weird side effects in upgrades and patch installations due to an enabled scanner although the database files and executables were excluded from scanning.
If you're urged to run Windows servers then I would put them in a separate network segment with a firewall in front and enable only the necessary SAP ports (and printing ports). This has a number of advantages:
- nasty RPC bugs can't be exploited because RPC to the SAP system should be disabled
- there's no need to reboot the Windows machines on every "Microsoft patch day"
A virus scanner adds, especially for production database systems, an indeterministic risc to the business.
Markus

Best practice power setting when doing a Site Survey for VOIP

Similar Messages

Maybe you are looking for