Best practices on wlan configuration

I have 6 accesspoints with controller . We are using voice video and data on the wireless with multiple SSID and vlans what could be the best practice on the accesspoints QOS and the switch port configuration of 3750 is it trunk or accessport?
Sent from Cisco Technical Support iPad App

Well you can start out by looking at the 792x deployment guide if that's what your using for voice.
http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7925g/7_0/english/deployment/guide/7925dply.pdf
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a0080810880.shtml
Sent from Cisco Technical Support iPhone App

Similar Messages

  • Request for any Best Practice document for configuring Service Parameters on CUCM 9.1.1

    Hi Team,
    Could you please send if you have any  Best Practice document for configuring Service Parameters on CUCM 9.1.1. That would really help.
    Thanks,
    Guru

    Hi
    There's no 'best practice' as such, but there are a few that I think should be default:
    Enabling CDR, On-Hook Pickup, CFwdAll Override... but really the settings are specific to the requirements of the deployment.
    Aaron

  • Best practice steps of configuration

    Hello All
    Can anyone write back on What is the best practice steps of configuration in HCM for a new implementation.
    Thanks

    Hi,
    SAP Best Practices is prepacked ready to use solutions for small and medium size Business units (SMBs)
    SAP Best practices is based on  Building Block methodology
    SAP Best Practices is fully documentation including preconfigured business processes, training material, data conversion tools, and test catalogs.
    Best Practcies is totally Buidleing block Methods.
    Building Blockss Contains:
    Business Configuration Sets (BC Sets)
    Sample master data
    Configuration documentation
    Print forms or reports
    Business Configuration Sets are group of Configuration Sets. As We can say group of tables for specific Business Process.
    for more details go help.sap.com., then go for Best practices you will very useful information.
    Regs,
    Brahma

  • Best Practices using Pre-configurator

    Hi
    Anybody aware of doing QM configuration as per the Best Practices through Pre-configurator.

    Hi
    By using sap library you can configure the QM module . Basically you have to know the process of Quality Managment
    Regards
    M B raju

  • Best practice for server configuration for iTunes U

    Hello all, I'm completely new to iTunes U, never heard of this until now and we have zero documentation on how to set it up. I was given the task to look at best practice for setting up the server for iTunes U, and I need your help.
    *My first question*: Can anyone explains to me how iTunes U works in general? My brief understanding is that you design/setup a welcome page for your school with sub categories like programs/courses, and within that you have things like lecture audio/video files and students can download/view them on iTunes. So where are these files hosted? Is it on your own server or is it on Apple's server? Where & how do you manage the content?
    *2nd question:* We have two Xserve(s) sitting in our server room ready to roll, my question is what is the best method to configure them so it meets our need of "high availability in active/active mode, load balancing, and server scaling". Originally I was thinking about using a 3rd party load balancing device to meet these needs, but I was told there is no budget for it so this is not going to happen. I know there is IP Failover but one server has to sit in standby mode which is a waste. So the most likely scenario is to setup DNS round robin and put both xserves in active/active. My question now is (this maybe related to question 1), say that all the content data like audio/video files are stored by us, (We are going to link a portion of our SAN space to Xserve for storage), if we are going with DNS round robin and put the 2 servers in Active/Active mode, can both servers access a common shared network space? or is this not possible and each server must have its own storage space? And therefore I must use something like RSYNC to make sure contents on both servers are identical? Should I use XSAN or is RSYNC good enough?
    Since I have no experience with iTunes U whatsoever, I hope you understand my questions, any advice and suggestion are most welcome, thanks!

    Raja Kondar wrote:
    wht is the Best Practice for having server pool i.e
    1) having a single large serverpool consisting of "n" number of guest vm
    2) having a multiple small serverpool consisting of less of number of guest vm I prefer option 1, as this gives me the greatest amount of resources available. I don't have to worry about resources in smaller pools. It also means there are more resources across the pool for HA purposes. Not sure if this is Official Best Practice, but it is a simpler configuration.
    Keep in mind that a server pool should probably have up to 20 servers in it: OCFS2 starts to strain after that.

  • Best practice MPLS design/configuration for small service provider

    We are a small regional service provider and did not have MPLS supported on our network.  To start supporting MPLS, I’d like to get opinions and recommendations on the best practice configuration. 
    Here is what we have today –
    We have our own BGP AS and multiple /24s.
    We are running OSPF on the Cores and BGP on the Edge routers peering with ISPs.
    We peer with multiple tier-1 ISPs for internet traffic. We do not provide public transit.
    What we want for phase one MPLS implementation –
    Configure basic MPLS /vpn functionality.
    No QoS optimization required for phase 1.
    We have Cisco ME 3600X for  PE. Any recommendations will be appreciated.

    Not sure what kind of devices or routers you have in your network but looks for if you have support for labeled multicast for MVPN support. That will avoid other complexity of using other control protocols (like PIM) in core.
    PE redundancy can be obtained by BGP attributes, CE-PE connectivity can be tunned using IGP or VRRP/HSRP...
    You can have mutiple RSVP TEs for various contract traffic and you can bind various kind of traffic to different RSVP Tunnels based on contract or service with your customer.
    RSVP-TE with link/node protection design will be of great help to achieve quicker failover.

  • Best practice Forms 10g configuration setup and tuning

    Hi,
    We are currently depolying forms 10g from 6i client/server version. Users are experiencing Form hangups and hour glasses. This does not happen that often but can happen any time, anywhere in the app (users do inserts, updates and deletes and queries).
    Is there a baseline best practice configuration setup anywhere either in the Forms side or the AppServer side of things?
    Here is our setup:
    Forms 10g (9.0.4)
    Reports 10g (9.0.4)
    Oracle AppServer 10g (9.0.4)
    OS = RedHat Linux
    Client Workstations run on Windows 2000 and XP w/ Internet Explorer 6 or higher
    Average No. of users = 250
    Thanks for all your help

    Shutdown applications within the guest.
    Either power off from Oracle VM Manager or 'xm shutdown xxx' from the command line
    It is possible one or more files could be open when the shutdown is initiated.
    Have found at least one case of misconfigured IP which would have resulted in the disk access being via the 'Front End' interface rather than the Back End.
    Thanks

  • SAP Best Practices for SSO Configuration

    Hello There,
    Are there any SAP Best Practices available for SSO Configuration. If so, Kindly help me with those..
    And also any Third party tools available in the market for SSO Configuration..
    Appriciate your Help on this.. Thanks in advance.
    Regards,
    Pranay S
    Edited by: Pranay Subedari on Apr 29, 2011 9:12 AM

    Hello,
    Types on the SSO are classified with the systems involved in configuration (i.e.) SSO between ABAP Stack and Java stack or LDAP, OS
    Refer the link for more details [Document Deleted]
    Regards,
    Anand
    Message was edited by: Jason Lax

  • Best practices in wireless configuration?

    Hi,
    Is there a best practice document that shows 3500 AP with 5508 controllers? The questions I have are below.
    1. Do I configure each AP to non overlapping neighbor channels(1,6,11 for 2.4GHz) or leave that to controller to decide? Does controller change the channel of an AP when it sees congestion on a specific frequency?
    2. For 5 GHz is it good idea to bond the channels? What frequency to use for neighboring APs? OR again, leave it to controller to shift as needed?
    3. For security what's best practices? 802.1x or different?
    Thanks,
    Sm

    1. Do I configure each AP to non overlapping neighbor channels(1,6,11 for 2.4GHz) or leave that to controller to decide?
    Let the controller(s) decide.  By default the Dynamic Channel Assignment (DCA) verifies the channel for interferrence every 600 seconds.  Because you have 3500 then make sure you enable Event Driven RRM (Radio Resource Management) on both channels.
    Does controller change the channel of an AP when it sees congestion on a specific frequency?
    The controllers will not change the channel when it sees congestion.  The controller will change the channel if it sees interference on the same channel.  The CleanAir will change the channel when it sees interference from non-AP interference like Bluetooth, Microwave ovens, cordless phones, etc.
    2. For 5 GHz is it good idea to bond the channels?
    Sure.
    What frequency to use for neighboring APs? OR again, leave it to controller to shift as needed?
    Leave this option in default.
    3. For security what's best practices? 802.1x or different?Sure.

  • Best Practice Document to Configure Quality Management Analytics

    Hi Experts,
    Can any one help in finding out the best practices document for installing BI content for Quality Management.
    Regards,
    Santhosh

    Hi Reddy,
    Thanx  for the link but I have a requirement to install the BI content for Quality management to present it to the client. So I need to install as a whole not for a particular requirement.
    I want to know do I need to install all the datasources like masterdata and Transactional which are available in RSA5.
    Regards,
    Santhosh.

  • OSB: What is best practice for reading configuration information

    I'm trying to establish the best way to utilise configuration information within OSB. At present I have a standard Java style properties file and Java callout to get certain information and I have also been experimenting with Dynamic Routing using an XML based Xquery resource.
    The latter appears to me the best approach and is described on page 3-40 of the OSB User Guide but it appears to be configurable only from the OSB console and not as a resource from within Workshop. Ideally I'd like to configure an XML resource file that is loaded from disk at OSB startup and then be able to use that via an XQuery.
    How have other people addressed the issue of getting access to parameter/control values at run time?

    Can you please elaborate a little on what you mean by making it available "via a OSB Server URL" What I have done:
    1) Created simple web application in domain directory.
    Sample web.xml
    <web-app xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns="http://java.sun.com/xml/ns/javaee" xmlns:web="http://java.sun.com/xml/ns/javaee/web-app_2_5.xsd" xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/web-app_2_5.xsd" id="WebApp_ID" version="2.5">
    <display-name>Sample</display-name>
    <welcome-file-list>
    <welcome-file>properties.xml</welcome-file>
    </welcome-file-list>
    </web-app>
    2) Deploy this web application in exploded format using weblogic console(http://localhost:7001/console) in the OSB domain instance.
    3) properties.xml is available via http://localhost:7001/Sample
    4) Use the above URL in your service callout.
    and how this avoids File IO and how it is cached? I'm not sure what you mean here.If we are using Java callout , we have to create File and close the File handle every time. There is this over head in creating/reading file in java every time java callout is used. This over head can be avoided if the XML is available over http. I'm quite sure that weblogic server will cache this XML file by default (What use is webserver if it cannot cache static content?), as this is not dynamic content. Weblogic Server forums will be the right place to get conformation on how to configure caching with web application..
    Thanks
    Manoj
    Edited by: mneelapu on Jul 1, 2009 8:46 AM

  • Best practice on storing configurations

    So a question for you all:
    It's my understanding that to make a set of LDOM configurations persist across a power cycle, they must be committed to the system controller (presumably it sticks them in some flash/eeprom memory somewhere).
    As best as I can tell you do this something like:
    ldm remove-config production
    ldm add-config productionThat seems a little awkward (why not "ldm save-config production"?). It also seems like something that ought to happen automatically when changes are made.
    Do folks agree that this is the "right" way to do this or am I missing something? What are you doing in your environment to make sure this happens on a regular basis?
    Thanks for any insights!

    Not quite following what you mean by "associated .as files ",
    but yes, that sounds fine.
    Tracy

  • Best practice required to configure CW and MARS SM and ACS

    Dear All,
    i had alot of managment program in my corporate org.
    CW LMS
    CW HUM
    CW QPM
    CW IPM
    ACS
    MARS
    Cisco IPS IDS 4260
    WLC
    tandberg system
    could you gude what is the best service from cisco that i could buy it to have a profetional  service to configure over all system in one integrated unite ,
    so i have one report shows all the issue with customize GUI, for managers , directors , and CTO, CEO,,
    thank you in advance,
    Ali Alkhafaji

    I have the code working without use of config files. I am just disappointed that it is not working using the configuration files. That was one of the primary intents of my code re-factoring. 
     Katherine
    Xiong , If you are proposing this as an answer then does this imply that Microsoft's stance is not to use configuration files with SSIS?? Please answer.
    SM

  • Is there any best practice for printer configuration for test environment?

    My Oracle ebs test environment has a scheduled refresh period where it will be refreshed with production test data and configuration time to time for BA, Dev to work on their enhancement.
    However, all the printer configurations are still pointing to production ones after refreshed, which means whenever there is a testing on-going, the doc / label / invoices will be printed to production printer.
    May I know if there is a way to globally change all the printer setup for the test environment, so that nothing will be directly to production?... Please assist.
    (currently, the only way is to change one by one and only if you are aware of it...)
    In case your organization has any other strategy on this matter, pls share also... Thanks a lot.

    user6775047 wrote:
    My Oracle ebs test environment has a scheduled refresh period where it will be refreshed with production test data and configuration time to time for BA, Dev to work on their enhancement.
    However, all the printer configurations are still pointing to production ones after refreshed, which means whenever there is a testing on-going, the doc / label / invoices will be printed to production printer.
    May I know if there is a way to globally change all the printer setup for the test environment, so that nothing will be directly to production?... Please assist.
    (currently, the only way is to change one by one and only if you are aware of it...)
    In case your organization has any other strategy on this matter, pls share also... Thanks a lot.If you do not want to use same printers then you have to it to point to the (TEST/BA Printers) after you are done with Rapid Clone. Any new printers need to be added manually (just the same way you defined you PROD printers) -- Rapid Clone Documentation Resources For Release 11i and 12 [ID 799735.1]
    If you want to edit the configuration, you could use FNDLOAD to download printers definition from the source instance, update the ldt file and use FNDLOAD to upload printers definitions.
    Is It Possible To Download/Upload Printer Definitions Using Fndload [ID 432616.1]
    Tips About FNDLOAD [ID 735338.1]
    Thanks,
    Hussein

  • Sanity check - Best practice for network configuration

    Basic configuration is this:
    Physical server has two interfaces. Two different networks. Generically we reference them as Front End and Back End
    Back End is dedicated to storage (nfs from netapp or Sun 74xx)
    xenbr0 associated with eth0 (front end)
    xenbr1 associated with eth1 (back end)
    For each Virtual Machine, have been creating two interfaces; vif0 with xenbr0 and vif1 with xenbr1
    The desire is to have all disk I/O use the vif1 -> xenbr1 -> eth1 path. So far it seems to be working that way.
    Questioning the setup because we have seen this sort of error when shutting down a VM
    nfs: server axqntap1 not responding, still trying
    In case it matters, mount options inside the vm are: rw,bg,hard,intr,timeo=600,proto=tcp,vers=3,rsize=32768,wsize=32768
    Any advice, ideas? Are we all wrong with the bridge config? Mount options?
    Thank you - Randall

    Shutdown applications within the guest.
    Either power off from Oracle VM Manager or 'xm shutdown xxx' from the command line
    It is possible one or more files could be open when the shutdown is initiated.
    Have found at least one case of misconfigured IP which would have resulted in the disk access being via the 'Front End' interface rather than the Back End.
    Thanks

Maybe you are looking for