Best Settings using the new Canon HV30 and Final Cut Express HD v3.5.1?

My wife presents programs at schools and uses digital movies that we make and edit as one of her media materials. We want to present higher quality videos that look more film-like. I am hoping that the combination I described above will enable this improvement. In the past we used a Canon ZR20 and iMovie HD and put these on DVD's that were then played on a MacBook Pro with with QuickTime or iDVD hooked up to an Epson PowerLite projector.
I am now the proud owner of a new Canon HV30 and Final Cut Express HD3.5.1 (had FCE for a while so know how to use it). From my research, though, it looks like FCE will not be able to handle CINE MODE recording in combination with 24fps progressive frame rate [HDV(PF24)] which would allow the enhanced effect of the Cinema Mode. I can't justify the cost of Final Cut Studio 2 so I am hoping that the new [HDV(PF30)] will allow me to more easily edit in FCE.
Does anyone know if this is true and if so can please tell me the settings that I need both on the camera and in FCE to get the best quality movie that can played directly from my MacPro using QuickTime or iDVD or from a DVD in the MacPro using the iDVD player. I won't have the opportunity to always play the videos directly from the camera to an HDTV because of the school setting and the need to use a projector.
I know this is a lot to ask for, but I am sure that it will come up again and again as more people purchase this new camera. Thanks for your time.
Sincerely,
Lou Hosta

Without totally repeating myself with my post to MaccyLeopard, I haven't shot any footage yet. After doing a lot of reading I think I confused myself more than helped myself as far as settings go. So if you remember from my initial post I am asking for advice and guidance primarily on camera settings with the HV30 that will be used in a classroom (artroom) setting and then edited using FCE HD v3.5.1. I wish I was the type of person that could jump right into using a new piece of equipment but I like to get the advice of others beforehand. That way I'm not always questioning myself as to 'whether or not is this the best I can get'. I also am wondering if the 30fps frame mode would be the best to use in the classroom setting? From my reading, this mode should allow more light onto the tape allowing me to shoot in conditions with lower light levels that are typically found inside? Finally, is FCE HD able to edit this new 30 fps frame mode of the HD30? I've heard that FCE HD can't handle the 20 fps frame mode.
Thanks for taking the time to help me out.
Sincerely,
Lou Hosta

Similar Messages

Canon HF200 and Final Cut Express

I just got my first Mac computer, a Mac Mini, and I ordered it with Final Cut Express. I also have a new camera, a Canon HF200, but I'm having trouble with it. When I connect it with the HDMI cable, nothing happens. I have some dics that came with the camera. The first one installed an image viewer type thing, but the second one is doing nothing and I can't even seem to eject it. Can anyone help? I just need to know how you can hook up a Canon HF200 with a Mac Mini and have the video content imported to FCE.

ColeRothacker wrote:
I just got my first Mac computer, a Mac Mini
congrats!
and I ordered it with Final Cut Express. I also have a new camera, a Canon HF200, but I'm having trouble with it.
I have the HF 10 & had an import error due to sound mixing settings, but we'll hold off on that for now...
When I connect it with the HDMI cable, nothing happens.
how are you doing this? did you buy the mini displayport adapter or something? if so, this will not work as that will be OUTPUT only, it can't import or input video.
I have some dics that came with the camera. The first one installed an image viewer type thing, but the second one is doing nothing and I can't even seem to eject it.
were these full size CDs? the canon software is useless, btw, so I wouldn't bother with it.
rebooting holding the left mouse button down will eject the disc, if it's the std size.
Can anyone help? I just need to know how you can hook up a Canon HF200 with a Mac Mini and have the video content imported to FCE.
USB cable & using the import function: http://www.apple.com/finalcutexpress/tutorials/ & select the one for "Transfer from AVCHD"

New Mac Pro and Final Cut Express HD

Ive just taken delivery of a new Mac Pro 2.8ghz quad core with ATI Radeon HD 2600. I've tried to open Final Cut Express HD and am getting an error message
' This software requires certain hardware or software which is missing -
AGP graphics card"
I've tried re-installing but no luck, any ideas ?
Thanks

Hi(Bonjour)!
You can use keyframe on filters from version 3.5 and later. And the new FCE HD 4.0 (who doesn't includes soundtrack nor the complete content of livetype library) includes newer filters and supports AVCHD.
Michel Boissonneault
Message was edited by: Michel Boissonneault

ProRes422HQ with a Canon HV30 and Final Cut....

I'm shooting with a Canon HV30 in HDV24p Cinema Mode. When interfacing to Final Cut Pro, my understanding is that the Cinema Mode records at regular 29.97, but with the look of 24fps. FCP crashes when I try to import it as ProRes422(HQ).
Can anyone please enlighten me as to what sequence settings I should be using to edit an HD movie, combining old home movies that are 720x480 alongside the HD footage? This is for a high end customer who wants the best quality possible (with reasonable render times and work loads on the CPU).

For the Canon VIXIA HV30 If you set cinema mode up correctly on the cannon your shooting in 24fps or 24p
Try using 1080i/24p setting for easy setup. You can get there by going to easy set up. Then chosing:
Format:HD
Rate:(all rates) from the "all rates" drop down chose 1080/24p firewire basic. Not sure on this.
I just got the camera and noticed that when I select the "firewire basic" option I have issues.
I have been using the: HD 1080i/60 as that is what cannon mentions that HDV is being encoded at.
Hope that helps. I plan on shooting some 24p clips soon and will post my results.
GLUCK

Canon HF200 and Final Cut Express 4 - not able to import movie files

Hello,
I have a Canon HF200. I have a 16 GB Duracell "pro photo" flash card. When I first connected my camera to my computer and clicked on "log and transfer" all of the movie clips on my card showed up in FCE 4. I did not import them at this time, however.
Now when I connect the camera, only newer videos taken with the camera show up as importable in FCE. Essentially, while the older videos remain on the card, I cannot access them and import them into FCE.
I am not able to import the files, which are saved as .CPI and .MTS files by simply dragging or using the log and transfer option.
If anyone can help me with this problem and tell me how I can retrieve the movie files I would really appreciate it.
Thanks a lot.

Do you own a card reader? Use that instead of the camera to transfer your files. If not, try using disc utility (or toast if you have it) to duplicate the memory card to a disc image (you can burn it to dvd if you want a back up of the original files) and then use the disc image to log and transfer.

Adobe CS4/5 and Final Cut Express On a MacBook Air?

Hey all
Im planning to get a MacBook for my GCSE's, and im leaning towards the air.
I will be running applications such as Adobe Photoshop CS5, After Effects CS5, Lightroom CS5, and Final Cut Express regularly, so would a 13" 1.86ghz MBA C2D Processor with 4gb of RAM be able to run these apps fast and efficiently with no lag? Or should I opt for the baseline MBP 13"? Im also looking for portability, as im going to be taking it into school
Thanks

After effects!? Yikes... that is a beast of a program! Depends how in depth you plan on using it. Are you going to be doing 3D animations with several camera layers? If so, I don't think a MBP is going to work too smoothly. If you are doing basic to moderate use of AE functions then I think it would work fine.
Just a heads up before buying, check out the apple refurb store. They have a bunch of MBP with different specs for a very reasonable price. I got my 17" MBP from there and it works awesome with the same warranty as new... for like $500 off!

Can I use IMovie HD 6.4 with Final Cut Express?

Can I use IMovie HD 6.4 with Final Cut Express?

Hi
Yes and no.
You can't get an editable material over from one to the other.
eg a misspelled word in iMovie project can't be corrected in FCE/P any version.
I use iMovie combined with FCE/P in just one case when there are to many drop outs
on the raw material eg recorded in LP-mode (90min on a 60min tape)
Then iMovie can import in a more forgiving way.
BUT
When this material is moved over to FCE/P the audio parts needs to be rendered
not just one time but whenever any change is done. A very nearv-wrecking and tedious
procedure.
Summary. Joint project should use same platform. In my cases me and friend has
each one full version of FCE4 and an external hard disk that contain the movie
project.
This we exchange with each other to do each the parts that we are on best to do.
Yours Bengt W

User Contributed Tips in Final Cut Express and Final Cut Express HD Forum

*The following User Contributed Tips are located in the Pro Applications: Video > Final Cut Express and Final Cut Express HD Forum:*
skalicki` - Working with AVCHD: Log and Transfer FAQs
http://discussions.apple.com/thread.jspa?threadID=2672530
Publish date: December 03, 2010
skalicki` - Final Cut Express: Basic Troubleshooting
http://discussions.apple.com/thread.jspa?threadID=2662419
Publish date: November 26, 2010
*The following related tips are located in other areas of Apple Discussions:*
Please see the User Tips Library

I'm relatively new to FCE myself, so I'll answer with what I know. I'm sure the more experienced folks will either add to or correct what I say.
1) For the Inconvenient Truth thing, I believe this would best be done in LiveType, which does allow you to do animations, and to work on individual letters and characters. Whether or not it could exactly reproduce the effects in the clip, I'm not certain, but I'm sure it could come very close.
2) For the Crowd or the Cross effects, there are two things going on at once: effects on the text, and effects on the video. My gut feeling is that both FCE and LiveType can do these, with lots of work and patience, but I'll defer to other people to answer.
3) The page peel is a transition built into FCE.

Final Cut Pro 4.5 and Final Cut Express 3.0 - 5 minute captures then freeze

Something I have found with Final Cut Pro 4.5 and Final Cut Express 3.0.
After Updating to Tiger - 10.4.11 and Quicktime 7.4.1 - Both Pro 4.5 and Express 3.0 will not capture more then 5 minutes and 12 seconds. If you are having this issue the solution I used to fix both Pro and Express issues was an update on the software. Final Cut Pro 5 fixed the problem (or 6 if you can) and with Final Cut Express, version 3.5 fixed the issue but if you can go with FCX 4.
Let me know if this helped or if you have found a different solution. Downgrading the os might help but that is too much of a pain and it's time to upgrade the software anyway.

#29: Need AGP Graphics card
Shane's Stock Answer #29 – Error: “Need AGP Graphics card”
http://docs.info.apple.com/article.html?artnum=302667
The Final Cut software is looking for a graphics card type that is required for that version of the software. FCP 4 and FCP 4.5 were released when AGP cards were the requirement. Attempting to open this on a Mac with a PCIe graphics card, such as an Intel Mac, will cause this error. FCP 4.5 is not supported on the Intel Macs. If you happen to have a PowerPC Quad processor Mac and get this error, you can try this hack:
http://www.xlr8yourmac.com/feedback/finalcut_pro_on_oldmacs.html
You can also press the "esc" key as you launch FCP. This enables FCP to open and run, but know that it might not work optimally.
If that doesn’t work, or if you have an Intel Mac, you are going to have to upgrade to a supported version of FCP…and FCP 6, part of Final Cut Studio 2, is the latest version.
Shane

Upgraded to Mac OS X Snow Leopard and final cut express 4 will not work

upgraded to Mac OS X Snow Leopard and final cut express 4 will not launch but my final cut express HD 3.0 version comes up. I reinstall my final cut express 4 upgrade disc and it still will not launch.
Where do I go from here?

You installed from the discs, right?
What happens when you try to launch? What are you doing to launch and what happens you do it? Can't see you computer from here. If you probably need to contact Apple with an installation issue on a new computer.

Final Cut Pro Studio 5.1.1 and Final Cut Express HD 3.5

Hi,
I have a client with both of these installed on the same machine (running 10.4.6).
When they try and launch either application, the splash screen comes up, loading various filters, etc. then they get an error message:
"File Error: A file of this name already exists" "OK"
Clicking "OK" closes the app.
Any idea:
1. What the file in question is?
2. Can it be deleted to let the app run?
3. Can Final Cut Pro Studio 5.1.1 and Final Cut Express HD 3.5 be used on the same machine?
I'll post this on the Final Cut Express HD 3.5 thread too (but with the order reversed).

What you did was not enough to delete the preferences properly.
This article tells you how. It is for FCE2 but works the same for FCE3 so I assume it is also OK for FCE 3.5:-
http://docs.info.apple.com/article.html?artnum=93690
It's simple to do so try it before reinstalling etc. - You should completely uninstall before reinstalling:-
http://docs.info.apple.com/article.html?artnum=301182
Ian.

When will the Universal Binary version of Final Cut Express HD be available

I'm purchasing a new mac mini Intel core duo and I need to know when the Universal Binary version of Final Cut Express HD will be available?

True but Apple will not support Mac Mini and MacBook's for some stupid reason.
It's available now and it's called FINAL CUT EXPRESS
HD 3.5
I'm purchasing a new mac mini Intel core duo and I
need to know when the Universal Binary version of
Final Cut Express HD will be available?

Panasonic SDR-H80 and Final Cut Express

Does anyone know whether the new Panasonic Camcorder Type SDR-H80 is compatible with an iMac running under the Leopard OS and Final Cut Express version 4.0.1?

Hey ,.. I just purchased the same videocam and I am having the same dilema? Did you figure something out on how to make itr work yet?

Using the new Nikon Transfer and It is not Compatible with PS6

I looking for a plug-in for PS6 specifically compatible with Camera RAW and Vista. I am using the new Nikon Transfer "ViewNX2" and PSC6 will not open camera raw without a plug in. It is telling me that I must convert to Windows7. I'm hopeful that there is a plug in avail to view with Vista Please HELP!!!

Nikon4 isn't the complete name of the nikon camera model you have, is it?
It would be something like D4 or D40 or......?
You can look on this chart for your camera model and minimum camera raw plugin required:
Camera Raw plug-in | Supported cameras
Try this camera raw 8.3 updater for cs6:
http://swupdl.adobe.com/updates/oobe/aam20/win/PhotoshopCameraRaw7-7.0/8.3.52/setup.zip
If not, this one should:
(read the whole page)
Adobe Camera Raw Help | Camera Raw/DNG Converter 8.4 on Mac OS 10.6, Windows XP, and Vista

Xacti HD and Final Cut Express -- It used to work great! How do I go back?

I have a Sanyo Xacti HD700. It gives me 1280x720 MPEG-4 AVC/H.264 files, which my Mac just loves. I used to be able to quickly edit the clips together in Final Cut Express, export using complementary QuickTime settings (specifically, those recommended by Vimeo for HD playback), and get beautiful MP4 files, relatively quickly.
Then, one day, a friend needed me to edit a quick video using a DV camcorder. It was confusing as heck getting the footage into FCE, and not particularly elegant getting it out. But, the project was done overnight, I washed my hands of it, and wanted to get back to making beautiful MP4 files again, relatively quickly.
Except I can't! Now, for one, encoding takes hours. Hours! My source videos and export videos are very similar, yet I sit and watch as the estimate for completion actually goes up for an hour before slowly coming back down.
And frankly, that would be fine, except now my exported videos are the wrong size. They include letterboxes, and the video itself is squished, stretched. So I wait four times as long for a ghastly video. The best I could do is use the Quicktime export settings to "crop off" the letterboxing, but there's still some black bars and it's just not the same.
Here's how my videos used to look:
http://vimeo.com/1067235
Here's how an exported video looks now:
http://vimeo.com/1655414?pg=embed&sec=1655414
What happened? Out of the box, everything worked perfectly. Now, tainted with actual tape, Final Cut Express seems like it's running my videos through six extra wringers and giving me clips worse than I'd get just cut-and-paste editing the Xacti files in QuickTime Pro!
I Googled my brains out, and all I've learned is, if I had Final Cut Pro, "Project Settings" would have all the switches I need. Well, I don't have FCP, just FCE.
Somewhere, something was set that I want to unset. Can anyone help? Do I have to delete every trace of FCE and just reinstall?
Mahalo for any advice!

It sounds like you didn't change the settings after you made the DV video. Did you switch it back to 1280x720 and make a new sequence in that format? Check item properties for the sequence you edited. What does it say? Also check item properties for any media you captured since working in DV.

Best Settings using the new Canon HV30 and Final Cut Express HD v3.5.1?

Similar Messages

Maybe you are looking for