Best way to connect iPod to LCD monitor?

Hello,
I wish to hookup my 5G iPod to a LCD monitor to display a slide show.
I know that some LCD's have RCA inputs (the yellow one) or S Video inputs and can thus go straight from the iPod. But many economy model LCD's do not have these.
So how can I hook up my iPod 5G/Photo or Video to a LCD which only has a VGA input?
Thanks!

Hi! I have a 2008 toyota camry and had to change my Aux connection for my 2nd Gen touch. All sound for the AUX, I believe comes from the connector not the 3.5 jack. The 2nd gen does not support the old firewire charging, so some of the third party cables will not charge a 2nd gen touch. Check this one out.
I bought this one, though the price was a little steep $49.00
http://www.griffintechnology.com/products/autopilot

Similar Messages

  • What Is The Best Way To Connect Ipod To Stereo Reciever With High Quality?

    I recently purchased an 80 gig and am a newbie. I ripped all my music at around 280kbps to retain good audio quality when playing in my car and home theatre system. There are tons of accesories out there (docks, jacks, etc) which is the highest quality to connect my Yamaha receiver. I would think a connection to the bottom of my ipod would be of a higher quality rather than using the headphone jack. Any suggestions would be great. I was thinking about using the monster itv link but mostly for audio. thanks

    OK - So now that you have all completely ignored the original question - in hopes of proving your manly-hood....
    Does anyone have an answer to the original question....
    "What is the best way to connect to a high end home stereo to retain the best sound?"
    For sure any connection going through the headphone jack will be a big step back - enough so that you would easily hear a sound quality loss in doing so.
    For the few of you who would like to argue/bicker/rant on the nominal sound quality loss....keep on doing so, but for those who actually have some respectable advice we would love to hear it.
    For the record, I tend to hear just outside the normal human auditory range...
    To help myself put it to rest already... a few years back I decided to conduct my own little listening test.
    I took 6 different common ripping modalities (from lossless - to - 128kbps in both MP3 & AAC.... then transfered all of them in order to a blank. Used the same song for each - the song chosen opened with a few clean crisp bars of high freq. music, followed by an instant explosion/drop into a tight & low bassline.
    The final cutoff that was achieved before I was unable to detect an audible difference was 198 VBR AAC. Having convinced myself that there was the ever sooooooo slight difference b/t 198 & 256, I went with my current ripping status of 256.... Just incase my audible range should become finally honed with age (yeah, like that is really going to happen) !
    This test was run over a Yamaha DSP receiver, running at a constant 110w per channel (w/a max of 220w). The speaker setup was a full surround set of Klipsch Reference Series..... each speaker housing 2 x 6.5 woofer (each housing 2 x 1" Titanium tweeters) And sitting along side the 5 surrounds was/is a 150w continuous 12in. Subwoofer.
    Now I am hardly stating that I have hearing as good as some of you extremely technically profound music enthusiasts out there, but for the majority of people making comments about sound quality, and lack there of - when played over a $120/40w Audiovox radio.... I'm sorry, but I would have to side on that of......"Hogwash, that you can hear a difference!"
    So.... if possible would someone please offer some advice on a dock or cable connection that will allow us to enjoy the music we ripped at whatever
    so-called range we did!
    For those interested in seeing who could hit the further bullseye with their eyes closed, You win!!! Now can you help us?
    MBP   Mac OS X (10.4.9)  

  • Best way to connect iPod to Shelf Stereo

    I have a shelf stereo that has a simple 3.5mm Audio In (like in car stereos). Would it be better to connect my iPod to the stereo via a cable that had two 3.5 mm connectors OR one 3.5 mm connector on one end and a iPod dock connector on the other end?
    Would both work?
    Would the dock connector cable sound better?
    Thanks for any thoughts you may have.

    Use the simple 3.5 mm cable from your headphone jack out to the stereo in port (if it has one). Going the other way (assuming you can find an adapter) is going to net you the same sound. For example, my Apple universal dock as a 3.5 mm out for audio. Doesn't sound any different coming out that port than it does out of my touch.

  • What Is Best Way To Connect iPod to Unpowered Speakers?

    I have a pair of speakers built into my wall. I do not have a stereo system that "feeds" the speakers that I can plug the iPod into as a source (to be directed to the speakers). And I don't want to buy such a system because all I will ever want as a source for those speakers is my iPod.
    Ideally, since I already have the speakers and an iPod, it would be great if there was a product that I could plug the iPod into, that was an amp, that I would then power the speakers.
    Can anyone recommend one?
    I know there are a gazillion products that you plug your iPod into that is an amp/speaker combo. That I don't need. And I know there are a gazillion products that allows one to plug an iPod into an existing amp/speaker combo.
    But are there any products that allows one to plug an iPod directly into unpowered speakers?

    But are there any products that allows one to plug an iPod directly into unpowered speakers?
    Just get a small receiver.
    Here's one -> Sherwood RX-4109 Stereo Receiver

  • What is the best way to connect my new MBP to monitor - DVI, VGA or HDMI

    What is the best way to connect my new MBP to a computer monitor?  DVI, VGA or HDMI?  Thanks

    I recommend the Apple MiniDisplay Port to DVI adaptor.  I would avoid VGA.  MiniDisplay Port to HDMI will work as well (3rd party).
    http://www.apple.com/search/?q=dvi%20adaptor&section=mac&geo=us

  • What is the best way to connect 2 monitors to a Mac Pro 13 inch (2013)?

    What is the best way to connect 2 monitors to a Mac Pro 13 inch (2013)?

    If you want to connect 2 Displays you must do it one with the Minidisplayport and one by HDMI if you have a Retina 13 Inch. i think the old MBP doenst have HDMi Out

  • What is the best way to connect a MacBook Pro to my HiFi system ?

    Hi,
    I'm new to Apple support communities having just bought my first Macbook Pro (a 17" 2.5GHz i7 model) and this is my very first community post.
    Im a bit of a Hi-Fi enthusiast, so, with my new MacBook Pro I've taken the opportunity of completely reloading my iTunes library in high quality Apple Lossless format. Took a while but now I've completed the task Im pleased I've done it.
    My question is, what is the best way to connect a Macbook Pro to a high quality Hi-Fi preamp - my Hi-fi system is musical Fidelity, and the pre amp (an A5  CR Pre amp) and this pre amp, which has superb audio quality, only has analogue phono inputs ? 
    I'm interested to understand what both the wired and wireless connection options are. I'm guessing one option must be to use the headphone output, but I have no idea if the output from the headphone socket on my new macbook (which is presumably designed to drive headphones) would be at a suitable level for a phono line level input ?
    Ive also read a few comments about using digital connection - and my second question would be - what is the audio digital connection on my macbook ?
    Aplogies if this question has been asked lots of times before but I've looked through some previous posts and can't find any answers in simple and straightforward language concentrating on the issue of connecting a MacBook Pro to an analogue phono pre amp input ?
    Thanks in anticipation of some advice.

    What is the best way to connect a MacBook Pro to my HiFi system?
    Look at the back of the reciever and see what your connection options are, the front headphone jack is output usually.
    The Mac's  analog audio in/out ports doubles as a optical in/out ports.
    The analog won't over power your amp, it's just a headphonejack, like a powered mic, just enough power to get the signal to the destination in one piece.
    Since you have a analog amp, your stuck with inferior analog connections, however you mentioned you wish to listen to the best sound quality of your lossless music.
    To do that your going to need a decent surround sound system with Toslink optical import jacks, a Toslink stereo jack to regular Toslink adapter, Toslink cable and enable the optical output in your System Preferences >Sound
    Another method is to use a Airport Express, it also has duo analog/opical out port. Then set up the Airport Express for iTunes streaming using the Airport Utility, then in iTunes setup the lower right corner one can set the connection.
    I recommned a Harmon Kardon surround sound system, with their 100 watt satelight speakers and the 200 watt subwoofer. Enable the "concert hall" and other neat effects which will turn your 2.0 (stereo) iTunes music into 4 channel speaker sound filling the room with music and sending the lower channels to the subwoofer.
    It will likely bring tears to your eyes that you can actually hear the full quality of your music as intended, I almost quarranty you will never want listen to music on a crappy iPhone or iPod again.
    If a surround sound system is out of your budget, you can get by using the Harmon Kardon "Go Play" portable stereo and a analog stereo cable.
    If your going to use your analog amp to power reference speakers, then there are various analog adapters of all sorts to make the appropriate connections once you know what they are, check out Radio Shack online for them.

  • What's the best way to connect the audio out of my Mac to my stereo receiver?

    I want to listen to my mp3 collection through my home theatre stero receiver.
    I have 2 audio interfaces that I connect to my mac through USB and Firewire: Digi Design Mbox mini and Maudio ProFire 610.
    I've tried going from a headphone 1/8'' connector from the headphone out of my mac to rca connected to the aux (or whatever) of my stereo.
    I've tried using a 1/4'' adapter on the 1/8'' to go from my mbox mini's headphone output to the rca aux on my stereo.
    The problem is I'm hearing distortions that sound like clipping, or static, crunchiness on certain frequencies in a lot of my mp3's that shouldn't be there.
    I listen to lots of music, and a lot of it uses distortion, like shoegaze, drone etc but I know what I'm hearing is unnatural.
    I even hear these flaws when I listen to headphones through the headphone out of my mbox.
    Page 2 on this instruction manual says I should be able to go from the monitor outs to my stereo. The monitor outs are 1/4 inch out so I figured I would need a 1/4 inch to rca cable.
    I got this one from monster thinking it should work. No dice.
    So my question is, what is the best way to connect my mac to my stereo? I need to avoid these distortions and flaws in the audio i'm hearing or I will go nuts.
    Why might I be getting these clipping distoritons?
    any advice would be fantastic

    It depends on how close the receiver is to the iMac. If it's just a few feet away you need at cable like:
    http://www.amazon.com/StarTech-com-THINTOSMIN6-Toslink-Digital-Optical/dp/B00016 W6Y6/ref=sr_1_2?ie=UTF8&qid=1316096392&sr=8-2
    However if the receiver is across the room or the house you would be best to enable Air Play, this enables you to wirelessly connect the receiver to the iMac. You will need the above cable and an Airport Express. If you are not familiar with Air Play navigate to:
    http://www.apple.com/itunes/airplay/
    I have been using it for quite some time and find it great. If you are not familiar with the Airport Express here is the link to it:
    http://www.apple.com/airportexpress/
    You can even find refurbished ones on Apples website for about $79.

  • What's the best way to connect latest iphone to 2010 Mini CooperS  for hands free

    What is the best way to connect the latest iphone to a 2010 mini Cooper S for hands free operation?

    Patrick Hindman wrote:
    Does anyone have any suggestions of what kind of hardware I should purchase to do this? Basically, I want a jam-up iTunes server that serves everything to each device (sorry, should have worded it this way sooner! . Maybe a MacMini server would do it? Or possibly just a Mac Mini or would Time Capsule do something like this?
    i use an old G4 Mac Mini running 10.5 Leopard, and it's on 24/7
    it runs in headless mode (ie no monitor) and i remotely administer it using remote desktop (or logmein if i'm out the house).
    i have a 1TB WD Mybook hanging off it connected via Firewire and that stores all my itunes content.

  • Best way to connect

    What is the best way to connect my iPOD nano to my 2003 Mazda 6? It doesn't have an auxiliary connection. And I've tried the iTrip with a dock connector, but it doesn't work.
    Any help and suggestions would be greatly appreciated.
    iPod nano   Windows XP  

    And some other options here:
    http://www.apple.com/ipod/ipodyourcar/accessories.html
    Gary

  • Best way to connect iMac to TV

    What's the best way to connect my iMac (2011) to my TV? My TV has HDMI inputs and my iMac has Thunderbolt ports, so I know I can connect them with a cable, but they are about 20 feet apart and I think that's too long for a cable run. Does anyone have suggestions?
    TIA,
    Thad

    Get an Thunderbolt to HDMI adapter and a 20 feet long HDMI cable.
    There is no problem with the length, but a 25 feet HDMI cable will be around 20$ on eBay.
    If you need to really go long distance, then you could get a HDMI over CAT6  extender.
    This one will allow 130 feet.
    Some models will let you extend up to 1000 feet!

  • What is the best way to connect MBP 13" - (non retina) to HDMI TV input

    What is the best way to connect MBP 13" late 2012 - (non retina) to HDMI TV input
    ...To get Video and Audio? With one cable ...
    I'm seeing that the "rocketfish" adapter is not handling the job (from these forums).
    I enjoy watching youtube videos, hulu, etc on the big screen through my laptop. The other Windows laptops I'ved had from Sony, HP, Dell, all had HDMI and was easy peasy.
    I don't have the patience to buy and return 10 different types of adaters (nor would Best Buy appreciate that)
    Thank you!

    Look for something like this:
    http://www.amazon.com/Cable-Matters-Premium-DisplayPort-Thunderbolt/dp/B004CADY9 I/ref=sr_1_6?ie=UTF8&qid=1356715728&sr=8-6&keywords=cable+displayport+to+hdmi
    Ciao.

  • What is the best way to connect PumpWorks to Labview? DDE or OPC

    What is the best way to connect quizix PumpWorks to labview?
    PumpWorks share data using Dynamic Data Exchange (DDE),what is the best way? To use an OPC Server betwen labveiw and pumpworks or  DDE?
    Solved!
    Go to Solution.

    Hi.
    If the instrumet can communicate with an OPC server I think both methods are fairly equal.
    There is a chance that you might have to reinstall LabVIEW without OPC server if you choose DDE, as it is known that it might conflict with the DDE server.
    http://zone.ni.com/devzone/cda/tut/p/id/4531
    http://zone.ni.com/devzone/cda/tut/p/id/7450
    -Tom

  • What is the best way to connect my ipad to the high-speed Internet connection in a hotel room

    what is the best way to connect my ipad to the high speed inernet connection in a hotel room

    every connection is a bit different. Generally, connect to the wifi, then you may need to open Safari, and may even need to try to get to one of your bookmarked pages to trigger the 'agree to our terms' page to come up.
    As to it kicking you off every so often, there are sometimes glitches with the wifi on iPads, you can also be subject to any programming the hotel has. Like I've noticed various places that only allow you to log on for a period of time before having to relogin.
    most hotels have 1-800 numbers, so you can always try calling that to see if their tech support has any tips for the frequent disconnection issue.

  • What is the best way to connect a G4 running 9.2.2 or 10 to an new imac running lion?

    What is the best way to connect a G4 running 9.2.2 or 10 to an new imac running lion?

    It should be possible to network them easily.
    Ethernet will be the most straightforward. There is no question that you can plug both Macs into a normal network and they can share files if you turn on File Sharing.
    The iMac has a Gigabit Ethernet port, and if the G4 also has Gigabit Ethernet, that will be a very fast connection through a gigabit-capable Ethernet cable or router. Otherwise both can use the slower Ethernet speeds with no problem.
    You can also network the two machines via a FireWire 800 or FireWire 400 cable if necessary, and use File Sharing that way too. Finally, you can put one Mac into FireWire Target Disk Mode, which turns it into a hard disk that the other Mac can see, but this is the least flexible since one machine goes out of service, and it's probably no faster than Gigabit Ethernet.

Maybe you are looking for