Best way to extend WiFi network with extreme and express using access contr

I just got my new AirPort Extreme and configured it to use 2,4 and 5 GHz. I also would like to use Access control. When I configure my AirPort Express to extend my network I see two strange things happen.
1. On both devices I have to configure access control. I figured this is an extension of the Extreme, the Express uses the same list
2. When I finished configuring I see the Extreme and Express flash heavily green and my wired network is becoming extreme slow. I think the two devices are talking to each other, but packets are dropping??
I tried a hard and soft reset of the both devices, no solution.
Does anyone recognize this problem and maybe you can tell me what the best way is to configure both devices.
Is there also a way to configure WEP instead of WPA for using my Nintendo DS.
The firmware I use is 7.5.2

Similar Messages

Extending wireless network with an aiport express

I have a netgear wireless router set up in my house on the second floor, but my room being located on the first floor i get a poor signal so i bought an airport express to extend my network. i tried going through the aiport exress setup assistant but that wouldnt work, so i ended up hooking it to my netgear router on the second floor to set it up in airport admin utility and then brought it back down to the first floor. my itunes worked with the speakers for about.. ten seconds then stopped. and my signal is just as weak as before.. any suggestions?

Unfortunately, it is simply not possible to use an Airport Express to wirelessly "extend" the wireless range of any model of Netgear wireless router. Netgear's wireless routers do not support Apple's implementation of a wireless distribution system (WDS), which is a necessary requirement for setting up an extended wireless network with the Airport Express. And no - it doesn't work the other way around either (Airport Express as base station, Netgear wireless router to "extend").
It sounds like you did successfully configure your Airport Express to "join" your existing wireless network - which will allow you to print and stream iTunes to the Airport Express. The problems you are having with Airtunes "hanging" on your Mac are almost certainly due to the poor wireless signal quality problem that you are already aware of.

Best way to configure a network comprising WLSE and many APs ?

Hi the Cisco NetPro community,
I would like to have a discussion with you on the best way to configure a network containing a WLSE and a large amount of Access Points.
The network I want to configure comprises some subnetnorks, each comprising about 10 access points (with some advanced settings for security). It might be a quite long and boring process to set the configuration for all those, so I am looking for the quickest and easiest solution to do so.
First of all, the configuration of IP addresses have to be done on each Access Point after unpacking it. The configuration of my network comprises 1 WDS active AP, 1 WDS backup AP and the rest of infrastructure APs, that for each developement site.
I thought about several solutions :
- 1st solution could be to apply a configuration file (i.e. load the config.txt file) to each AP manually, changing some values (IP, local radius...).
But problem is that passwords can't be changed with text editor because of the passwords written in "hash".
- 2nd solution could be to configure each AP (after IP is set) using its web interface.
No more problem for hash written passwords, but this method is quite boring when surfing on menu pages of the AP web interface...
- 3rd solution, which could appear as the best solution, is to create a template on the WLSE, and to apply it to all APs.
No more boring connection to each AP, but problem are : we need to create as many templates as APs (or change some parameters each time), and we still need to set parameters directly to APs before (SNMP, SSH, WDS configuration...), in order the WLSE to manage the APs.
So, what do you think could be the best solution in order to deploy such a network with many APs ?
How is it possible to avoid (so far as we can) the configuration of APs one by one ?
Thanks a lot in advance for your consideration and your ideas !
Alexis.

Well for one of my clients that had over 60 sites, we actually created a couple of templates. We created a basic template and a template for each site. You can have the ap's obtain the configuration from the WLSE, but you need to configure a DHCP option. My client did mac address reservations, but of course you need the mac address first. I guess you can also let the ap get an address and change it later. They tried doing different things, first let the ap obtain a default config and then pushing out the configuration for that site.
As for the hash, you can set the password in ascii... when you do a show run, then of cours it will be hash'd.
http://www.cisco.com/en/US/docs/wireless/wlse/2.12/user/guide/deploywz.html#wp1936755

How do i extend my network with a airport express

How do I extend my network with mt airport express

Hi Tesserax, I'd like to join this discussion. It seems Jasonbeyer didn't reply, but I have a question related to his.
I'd like to extend the wireless signal from my Cisco Model DPC/EPC2202 VoIP Cable Modem (802.11n) to the living room where, at the moment, it is non-existent. I assume there's inteference or the signal cannot reach through the concrete walls and rooms leading up from my bedroom to the living room.
My question is:
I'm thinking of extending my wi-fi signal by using the Airport Express and simultaneously using it to connect to my hi-fi to play iTunes from my bedroom's iMac.
Something's telling me it's not going to be that easy. I'm using an iMac (7,1) if that's any help or clue.
What are the things I should take note of and will Airport Express be compatible with my modem? Would I have to get TWO Aiport Express to bridge the signal to my living room?
Thank you everyone for your time. Cheers!
Kane

How do I extend the range of my existing Belkin WiFi network with an Airport Express Gen 2?

It is my understanding that the second generation of the Airport Express can be used to extend an existing non-Apple WiFi network. From all I read, it was very difficult to do with the Gen 1 Airport Express, but I don't find anyone referencing the Gen 2. My router is a Belkin Share F7D3302 V1 (updated to current firmware as of yesterday). I am able to attach to the Belkin network and stream music to my home theater, but would also like to extend my WiFi. Any help is appreciated.

It is my understanding that the second generation of the Airport Express can be used to extend an existing non-Apple WiFi network.
Not sure where this information has come from....and it would be extremely surprising if this were true. Do you have a link to an official announcement from Apple that would confirm this?
As far as we know, Apple's "extend" setting remains a proprietary feature that is designed to work only with other Apple routers. The "new" Express appears to carry on that tradition.
As such, it would be very unlikely that any of the Apple routers would be compatible with a Belkin product....or any other manufacturer's product for that matter.....if you are thinking of extending using wireless only.
If you figure out how to do this.....it will be a breakthrough of major proportions. Please let us know if you are successful.

Extending My network with three Airport Express or buy an Airport Extreme?

I live in a large three story house and currently have it wirelessly networked using two Airport Express' but my signal is very weak on the third floor and in other spots throughout the house.
Would it be possible to buy a third AE and extend the network that way or would I be better off buying a AEBS?
Any thoughts or suggestions would be greatly appreciated.
Thanks

It will really depend on the construction materials used in your house or any other forms of Wi-Fi interference that could prevent a clear wireless signal. Both routes, you suggested, will have it advantages and disadvantages.
Extending the existing network wirelessly using a WDS, effectively, cuts the throughput in half for each base station in the chain...so, in this case the second AirPort Express Base Station (AX) (acting as a WDS relay base station) would only get half that of the first AX (acting as the WDS main base station). In turn, the third AX (acting as the WDS remote base station) would receive half of the second's throughput. The good news is that you should have a strong signal across each of the AXs, just lower throughput the farther along in the chain.
The 802.11n AirPort Extreme Base Station (AEBSn) has a greater range than either the older 802.11g version or the AXs. You may find that it will provide enough to cover you entire house. In the off-chance that it doesn't, you can still use it to create a WDS between AEBSn and your current AXs.

Trouble extending my WiFi network with older Airport Express

Hi,
As the question states, I have an older Airport Express which I have dug out to try and extend my WiFi network in a new house.
I am on Virgin Media (fibre optic) in the UK and get a good WiFi service but one room in the house (which I have just turned into a cinema/media suite) has no reception.
I have successfully managed to 'create a new network' via the Airport Express and the signal strength is 100% but for some reason if I try to reconfigure the device to extend the existing network I get no improvement at all from the (zero) signal I was receiving before.
Am I doing something wrong? Or is there an additional step I am missing?
I could live with having a secondary network but what I would really like to achieve is Home Sharing from my main computer, so that I can access my photos, movies and music etc. from iTunes on the big screen. If the computer exists on another network my iPad, iPhone and AppleTV can't see/use the media from that room.
Many thanks in advance,
Colin

Are these the steps you used?
To create a wireless extended network, you must place any extended Wi-Fi base stations within range of the primary Wi-Fi base station.
Start with the device that will be configured as the primary Wi-Fi base station. Then configure your extended Wi-Fi base stations, ensuring that each is within direct range of the primary Wi-Fi base station.The physical location of extended Wi-Fi base stations will vary according to the building environment and may require some experimentation.
If you have configured your Wi-Fi base stations in the past, it may be helpful to do a factory default reset of each Wi-Fi base station that will be part of the wireless extended network before you begin.
Configuring the primary Wi-Fi base station
Power on all 802.11n Wi-Fi base stations and allow them time to appear in the AirPort Menu Extra.
Open AirPort Utility (On a Mac, choose Go > Applications from your desktop, click the Utilities folder, then open AirPort Utility. In Microsoft Windows, choose Start > All Programs > AirPort to start AirPort Utility).
Select the primary Wi-Fi base station in the Base Station Chooser, then click Continue. Note: If you see a message appear that indicates that the Wi-Fi base station has been reset, click Cancel to continue.
Click Manual Setup. Enter the base station password if necessary.
Click AirPort in the toolbar.
Click Wireless.
Choose “Create a wireless network” from the Wireless Mode menu.
Select the “Allow this network to be extended” checkbox.
Enter a Wireless Network Name.
Optional: By default, Wireless Security is set to None so that no password will be required to join the network. We recommend you click on the Wireless Security menu, select WPA2 Personal, and create a password between 8 and 63 characters long.
From the Radio Channel Selection menu, select Automatic.
Click Update.
The next window may indicate that there are some problems. Resolve the problems, then click Update.
You are now ready to add extended Wi-Fi base stations to your network.
Configuring an extended Wi-Fi base station
Place any extended Wi-Fi base stations within range of the primary Wi-Fi base station
Ensure that all 802.11n Wi-Fi base stations are powered on and allow them time to appear in the AirPort Menu Extra
Open AirPort Utility (On a Mac, choose Go > Applications from your desktop, click the Utilities folder, then open AirPort Utility. In Microsoft Windows, choose Start > All Programs > AirPort to start AirPort Utility).
Select the Extended Wi-Fi base station in the Base Station Chooser, then click Continue. Note: If you see a message appear that indicates that the Wi-Fi base station has been reset, click Cancel to continue.
Click Manual Setup. Enter the base station password if necessary.
Click AirPort in the toolbar.
Click Wireless.
Choose “Extend a wireless network” from the Wireless Mode menu.
Choose the network you want to extend from the Network Name menu.
Enter the network and device password if necessary, then click Update.
The next window may indicate that there are some problems. Resolve the problems, then click Update.

Ist it possible to extend a wifi network with sevral Airport Express's?

Hi, I live in a house with 3 floors. My router and my timecapsule are located on the 2nd floor and I want to extend my network wirelessly to the first floor and the ground floor by adding several (2) Airport Express stations to my network. Is this possible?
Basically like on the picture linked:
https://www.dropbox.com/sh/g8mvrbgo4r38lzr/5uCsbQ5E2w?v=1mci
Somehow it works brilliant but, once I add the second AE my MacBook won't sign into the second AE but will stay in the first. Resulting in just not extending my network.
Thanks

Somehow it works brilliant but, once I add the second AE my MacBook won't sign into the second AE but will stay in the first. Resulting in just not extending my network.
That's because you can only wirelessly "extend" the network one time, not two.
Apple's "extend" setup works like the hub and spokes of a wheel. The Time Capsule would be your hub. There can be multiple AirPort Express devices, but each Express resides at the end of a separate spoke...and it communicates directly to the hub....not to another device at the end of another spoke.
The second extender is "joining" the network, but it provides no additional wireless signal coverage when it "joins".
You will need to move the second AirPort Express closer to the Time Capsule.....to the point where the display indicates that both Express devices are connected to the Time Capsule.
Another approach might be to move the Time Capsule to the central area on the 1st floor, then locate an AirPort Express above and below that area. That would work.
If that is not possible, then you will need to think about a wired Ethernet connection from the AirPort Extreme to the location of the second AirPort Express.

Best way to manage large library with AAC and MP3 versions of files

I have a large library of music. I listen to music through iTunes and iPod/iPhones, but also other devices which only support MP3, and not AAC. I typically convert iTunes purchases to MP3, but I'm left with two copies of each song in the same folder. I'm looking for recommendations on the best way to manage what would essentially be a duplicated music library - a high quality version I use with my iTunes/ipods, and a lower quality MP3 version for the devices that only support that format.

I have had a similar problem. I have all my music residing on a NAS where I access it from iTunes (for managing my iPods/iPhones) and a Tivo PVR (which is connected to my house stereo system.) The problem is that Tivo does not recognize AAC. So I've used iTunes to create mp3 versions of all my purchased AAC music. Because the NAS is set as my iTunes media folder location, iTunes puts the mp3 copies back into the existing folder structure (which it keeps organised) on the NAS. Tivo accesses the NAS directly, over the network. But iTunes also puts the additional copy into the iTunes library which leaves me with multiple copies of the same songs on iTunes AND my iPods. Having multiple copies on the NAS (mp3 for Tivo and AAC for iPod) is OK: I've got plenty of space on the NAS and the Tivo doesn't 'see' the AAC files.
The solution I'm planning to implement is to delete the mp3 entries from the library as soon as I create them (leaving the files in the media folder.) But what I'm looking is for a way to automatically select the mp3 copies (for deletion) from the existing duplicates list. Any ideas?

Extend wireless network with multiple airport express and netgear powerline

I currently have the following network configuration:
1. Using ATT u-verse (2-wire 3800HGV-B "modem") to internet
2. Disabled the u-verse modem wireless router, and have connected an Apple Time Capsule wireless router (on a DMZ)
3. Have four Netgear XAVB5001 powerline adapters connected to the time capsule (for our iMac desktops and the Apple TV)
4. Have an Airport Express wirelessly connected to the time capsule to extend range (for our iPhones and iPad)
All this is currently working. What I would like to do is the following, keeping 1-3 above the same:
4. Connect the airport express to the time capsule via Netgear XAVB5101 powerline adapter (instead of wirelessly connecting to the time capsule as it is today) and use it to extend the wireless range of the time capsule
5. Add ANOTHER airport express to the time capsule via powerline adapter (and extend the wireless range elsewhere in the house).
Does anyone have any experience with this kind of setup and can assure that it would work? (I'm trying to decide whether to spring for a couple more powerline adapters and another airport express)
Thanks in advance!
Dave

I had a VERY similar problem: I was trying to extend my wireless network using a hardwired ethernet connection from Airport Extreme to my Time Capsule. Every time I plugged in the wire to the TC, everything disappeared. Unplugged, and boom. Came back.
Here's how I solved it:
Go into Airport Utility and select the unit you are trying to use as a wireless extender and choose to edit it. Then, on the wireless tab select CREATE a wireless network. But, give it the exact same name and password. This is completely counter-intuitive. You would think to choose EXTEND, but this would be wrong. Next choose the network tab. And, select Router mode to Bridge (off).
By choosing the same name and password, your phone, laptop, etc. will think it's on the same network and move seamlessly from one to the other.
See if this fixes your issue. Fixed mine instantly. AND, it only took 3 painstaking hours of checking ethernet connections and rewiring jacks, etc. to figure it out. LOL

Extending a network with 2x Airport Express

I tried searching and couldn't find any discussions which answered my question. We have a home office which was just completed (an actual, separate structure, not just a room) and I need to connect it to the main house where our Internet connection comes in. What I'm trying to do is use an Airport Express (802.11n), which wirelessly connects to the main router, an Airport Extreme (802.11n, 2nd gen.). This Airport Express is then connected via Cat5e cable and a gigabit switch (it's a pretty long run) to another Airport Express (802.11n). This second Airport Express will then reconvert the connection to wireless and allow us to connect our devices in the office to the rest of the network and get access to the Internet.
Here's a crappy diagram I drew in Paint: http://i.imgur.com/5KrhX.png
When I first connected the second Airport Extreme in the office, I got a pop-up showing the new device in Airport Utility. However, no matter how I configure it, I cannot successfully get it to join the network properly. I've gone through the process multiple times, but am not having any luck. I've attempted to get it to "join my existing network" and then specify to connect via Ethernet and extend my network, and then tell it which device (the first Airport Extreme) it's connected to via Ethernet. Once I try to commit the changes, though, the device restarts and ends up with a blinking orange light, disappearing entirely from the list of devices in Airport Utility.
I've checked and the Airport Extreme is set up to allow devices to extend the network, and I've tried setting the first Airport Express to both "Join my wireless network" and "Extend my wireless network," though neither seems to make a difference.
Am I missing something, or trying something that won't work? Any ideas?
Thanks!

When I first connected the second Airport Extreme in the office, I got a pop-up showing the new device in Airport Utility. However, no matter how I configure it, I cannot successfully get it to join the network properly. I've gone through the process multiple times, but am not having any luck. I've attempted to get it to "join my existing network" and then specify to connect via Ethernet and extend my network, and then tell it which device (the first Airport Extreme) it's connected to via Ethernet.
You have two choices with AirPort Express #1:
Configure the AX as a wireless Ethernet bridge. Apple calls this configuration a ProxySTA. In this configuration, the AX would join the wireless network provided by the AirPort Extreme, and then, share this connection out it Ethernet port to the Ethernet switch.
Configure the AX to extend the wireless network of the AirPort Extreme. This would also enable the base station's Ethernet port.
Of the two, I would recommend the first option.
To configure the AX as a ProxySTA, you need just to make the following two setting changes:
Wireless Mode = Join a wireless network
Allow Ethernet clients (enabled)
Both of these settings are on the Wireless tab in the AirPort Utility.

Extend wifi network via PLC + Airport express

Hi everyone,
I have a linksys WRT54G and an Airport Express. I'm using the WRT54G to create a wifi network (toto), and the AE is too far away to get the WR54G signal.
I want to connect the WRT54G to the AE via PLC to extend the toto network, but when I try to select "extend a wireless network" in the airport utility, it says "the network you selected cant be extended..."
Ideally I don't want do have 2 wifi networks... And I think WDS is not what I want to do.
Do you know what settings do I have to use ?
Many thanks !!!!!
Message was edited by: dathieums

Hello dathieums. Welcome to the Apple Discussions!
The following are a few articles that you can find in both these Discussions and on the Internet where users have been successful extending the this Linksys wireless router with an AirPort Express Base Station (AX), that you may find helpful in configuring yours:
o How to extend your Linksys WRT54G with AE
o Linksys WRT54G and WDS
o Extend a Linksys WRT54G network via AirPort Express
o Linksys WRT54G, Airport Express, and WDS
o AirTunes, AirPort Express, and the WRT54G

Extending Wireless Network with older and newer airports

Hello all,
I have 1 brand new Airport Extreme, 1 somewhat new Airport Express (802.11n) and 3 older Airport Expresses and I'm at a loss at how to use them all together to get wireless coverage in our apartment.
For some reason I just can't seem to get the older expresses to extend any network. I started with the Extreme as the base station and set the radio mode to 801.11g and used the Airport Utility to set up an Express to extend the network but it didn't seem to actually extend the signal but rather it just joined the network. I was hoping to use the Extreme and the 3 older Expresses to set up an 802.11g network, but now I'm not sure how that will work.
It's strange because when I first purchased the 802.11g Expresses several years ago it was easy to set up and extend the wireless network, not sure what is different now.
Any thoughts would be helpful.
Thanks!

There are basically two methods to extend the AirPorts' wireless network by wireless: 1) The 802.11g "static" WDS, or 2) 802.11n Extended Network or "dynamic" WDS.
The second option is only available when ALL base stations are 802.11n models. The first option is available when either ALL base stations are 802.11g models or you use a mix of 802.11g & 802.11n models.
Since you have a mix, you should be aware of two significant drawbacks of the earlier static WDS: 1) The overall network can only operate in the 802.11g radio mode. That effectively nullifies have any 802.11n devices, and 2) For each base station added to the WDS, the overall bandwidth (speed) is cut in half ... so with a total of five base stations, you would get around: 54 / (2 x 2 x 2 x 2) = 3.375 Mbps! I hope you don't plan on doing any video streaming, especially not HD video.
If you still want to push ahead, please check out the following Apple Support article how to do so.

How is the best way to export my project with clips and videos?

I would like to save my project and export the project with clips and videos included. What is the best way to do it?

Can you clarify:
clips and video
Seems as though you want to retain the original media?
Export as a Master File to get a good quality export file of your Timeline.
Al

Best way to Organise - Shared Documents with Others and to iPad2

I have a large number of iWork documents on my iMac. Some of these documents I wish to share with others and also to my iPad2.
Previously I used the iWork.com BETA and this was integrated with Pages, Numbers and Keynote through the 'Share' iCon in each application. This was very convenient linked with email and worked seamlessly. However now I have to Upload and Download documents through the iCloud website, issue separate email invitation. A more manually intensive way of achieving the previous 'slick' method.
Has anyone found a good way of organising and distributing documents?
Any suggestions for a good iWork.com replacements?

That is a quesiton I also have. It seems that there is no way to do this currently. When it comes to documents, iCloud is more or less useless because (a) it can only sync files that are stored inside the apps and (b) in iOS you can't move files out of the apps.
The best solution I know about is "wuala". It syncs everything you want on your Mac and it runs on all common systems. So I have synced all my documents across my Macs, iPhone and iPad and can share files & folders with others.
The only problem now is, that once you open a file on the iPhone or iPad, it will be instantly saved there (inside the app) and you can't move it to the original location (the sync folder in wuala). This part breaks the whole concept and I don't know any alternative.

Best way to extend WiFi network with extreme and express using access contr

Similar Messages

Maybe you are looking for