BGP and auto-summary enabled or disabled with "network" command

http://www.cisco.com/en/US/tech/tk365/technologies_q_and_a_item09186a00800949e8.shtml#five
I just modified the below quoted by adding numbers
My understanding is this:
A- I hope my numbering to the quoted above is right ,,,I numbered it to be easy to point to it.
B- What does it mean by locally originated, does it mean within AS ?
1- auto-summary is enabled it summarizes the locally originated BGP networks to their classfull boundaries without caring to check if there are any entry in IGP routing table,,,,Am I right ?
2- auto-summary is disabled, the routes introduced locally into the BGP table are not summarized to their classfull boundaries, without caring to check if there are any entry in IGP routing table,,,,Am I right ?
3- I could not match his example with his explanation
4- It is obvious.

Thanks hritter
I think you forgot to answer this :
1- Does that mean with "no auto-summary" we do not care about the exact match
The author says:
"3- When a subnet exists in the routing table and the following three conditions are satisfied, then any subnet of that classfull network in the local routing table will prompt BGP to install the classfull network into the BGP table.
* Classfull network statement for a network in the routing table
* Classfull mask on that network statement
* Auto-summary enabled "
Correct my understanding to the above quoted
The author says: For example, if the subnet in the routing table is 75.75.75.0 mask 255.255.255.0 {match the above quoted : When a subnet exists in the routing table}.
The author says : and you configure network 75.0.0.0 under the router bgp command (for my understanding it does not match the above quoted first comdition : Classfull network statement for a network in the routing table},,,,,,,he says 75.0.0.0 under bgp table and the above quoted says under routing table (IGP table)

Similar Messages

Download connections doesn't close after I cancel the download, it keep like I am download and only close when I disable the network adapter or reset the router or the firewall

download connections doesn't close after I cancel the download, it keep like I am downloading and only close when I disable the network adapter or reset the router or the firewall.
I use pfsense as my firewall and see the traffic not reseting to zero when I cancel download.
Also, IE doesn't have this problem. When I cancel the download the traffic drops to zero.

And this problem seems to be systemwide. Since I created a new user and under which problem still exists.
Hope apple will look into it

Import EIGRP default route only with network command

Hi,
Does anyone know why I can only import the default route learned by EIGRP (from a CE router) in the VPNV4 table with the command ?network 0.0.0.0? under the address family? Is this the correct behavior?
router bgp 100
address-family ipv4 vrf red
redistribute eigrp 200
no synchronization
network 0.0.0.0
exit-address-family
PE9(config-router-af)#do show ip route vrf red 0.0.0.0
Routing entry for 0.0.0.0/0, supernet
Known via "eigrp 200", distance 90, metric 547840, candidate default path, type internal
Redistributing via bgp 100, eigrp 200
Last update from 91.91.91.1 on FastEthernet0/0.91, 00:04:11 ago
Routing Descriptor Blocks:
* 91.91.91.1, from 91.91.91.1, 00:04:11 ago, via FastEthernet0/0.91
Route metric is 547840, traffic share count is 1
Total delay is 20400 microseconds, minimum bandwidth is 100000 Kbit
Reliability 255/255, minimum MTU 1500 bytes
Loading 1/255, Hops 4
PE9(config-router-af)#do show ip bgp vpnv4 vrf red 0.0.0.0
% Network not in table
PE9(config-router-af)#
PE9(config-router-af)#network 0.0.0.0
PE9(config-router-af)#
PE9(config-router-af)#do show ip bgp vpnv4 vrf red 0.0.0.0
BGP routing table entry for 91:91:0.0.0.0/0, version 1068
Paths: (1 available, best #1, table red)
Flag: 0x820
Advertised to update-groups:
2
Local
91.91.91.1 (via red) from 0.0.0.0 (9.9.9.9)
Origin IGP, metric 547840, localpref 100, weight 32768, valid, sourced, local, best
Extended Community: RT:118:118 Cost:pre-bestpath:128:547840
0x8800:32768:0 0x8801:200:522240 0x8802:65284:25600 0x8803:65281:1500
mpls labels in/out 28/nolabel
PE9(config-router-af)#
Thanks,
Marcelo

Hi Marcelo,
Yes this is normal, a default route unlike any other routes is not redistributed between routing protocols by default, in the case of BGP you have 2 options, either use a network command and make sure that the route is in the routing table (via EIGRP in your case), or use redistribute + default-information originate, you can test this by removing the network command and adding the default-information originate under the address family.
HTH,
Mohammed Mahmoud.

How can I continuously auto-save and auto-name the JPEG files with a controlled time interval

Hi,
I am newly involved in some Labview projects that out of my knowledge. I am trying to save multiple JPEG images from a live imaging task to a folder in the computer hard disk every certain minutes. I'd like to name these files with the date and time (eg. Img_06012011_1635. jpg).Then, after hours long image capturing, I can have all the image files in a neat order.
My goal is to have the jpg files auto saved and auto-named with the data and time at that moment. I also need to control this waiting time between each savings.
Could you please show me some hints about this? See the vi attached, I know I need to do something on the "write path" part on the up right corner. Thanks!
Solved!
Go to Solution.
Attachments:
capture.vi ‏28 KB

Thanks, Steve. When I built up a path with the date and time info and send them to the WriteJPEG File.vi like you mentioned, it stopped saving any files into the folder. Do you think this is the problem from my while loop?Could you show me if there is any other secret functions that restrains the file saving?
I am planning to save the image files every 30 secs,for example, and then I can have a bunch of jpg files with their unique names after hours long image acquisition.
I appreciate you kindly help!
Attachments:
capture(updated).vi ‏29 KB

Can't enable eprint even with network connected

Windows 8 computer network is connected but eprint won't enable HP8600. Have followed directions for pushing refresh button. Still disabled.

Try the steps below. Make sure nothing is entering under proxy address.
1. Open an internet browser type printer's IP address.
2. Should bring you to the printer's status page.
3. Select network tab at the top.
4. Left hand side select IPv4 under wireless.
5. Under DNS address Configuration select Manual DNS Server.
6. For Preferred enter 8.8.8.8
7. For Alternate enter 8.8.4.4
8. Select apply. You might get a warning saying this could interrupt connection that's fine.
9. Turn printer off for about 30 seconds then try again.
Let me know it goes.

In the OSPF routing, Why can't use the command "no auto-summary"?

Hello
I will post the article here because this question.
The question for OSPF.
Am I more than trying a variety of routing's a wonder suddenly become, OSPF is why there is no "no auto-summary" of commands like protocols such as RIP and EIGRP?
It's strange grammar?
Yes, using the Google Translator.
Please consider it.

ckfurtn01,
By default, RIP and EIGRP summarize networks to their classful boundaries. No auto-summary disables that feature.
In OSPF, we need to configure wildcard masks to identify our networks. For example, in EIGRP network 10.1.1.0/24, with auto-summary enabled, will advertise a 10.0.0.0/8 network. In OSPF, to identify the same 10.1.1.0/24 network we would advertise 10.1.1.0 0.0.0.255 area X. If we wanted to do the classful boundary then it would be 10.0.0.0 0.255.255.255 area X.
OSPF, in short, does not perform auto-summarization so it is not a needed command. Hope this helps.
v/r
Mike

Can't Login With Network Account After Upgrade To Yosemite Server 4

I've been putting off this troubleshooting for a while now, and after trying everything I could find, decided to post.
- After upgrading my server to Yosemite with Server 4, and my MacBook to Yosemite, I can no longer login with any network accounts.
- I was on clean installs of Mavericks before the upgrade.
- I'm using SSL for the OD, with a GoDaddy cert, the same one that was working on Mavericks.
- I've tried removing the laptop's binding using the Users and Groups preferences dialog, which does not remove the laptop's entry from Open Directory, so I manually deleted the record on the server.
- I then choose to Join again, and it looks as though everything goes through, but I still cannot login with a network account. Also, when rejoining, it does not create a binding on the server.
- If I use the Directory Utility->Services->LDAPv3, and add it that way, entering the FQDN and checking Encrypt..., Use for auth and Use for contacts, it asks me for the directory admin username and password, and does in fact create the binding on the server, but I still cannot login. What's strange about that method, is that it forces the use of the IP address of the server, rather than the FQDN, like I entered it, which would of course have problems, because the certificate's common name is the server's FQDN. It does not allow me to change from using the IP address, graying out that field.
- I've also tried destroying the OD and restoring from archive to no avail.
It looks like many users have hit dead ends with this, with some having success by completely formatting and setting up a new iteration of the server, but I will not be doing that. However, I'll be happy to try any other suggestions.
Thanks for your time,
   -- Mike

     Okay, I've finally resolved the issue, thanks to the Apple Enterprise tech support team. I'm thinking they wouldn't mind if I share this information, but I can't guarantee that this will work on your system or, worse yet, degrade your system further. However, that's fairly unlikely, just make sure you have plenty of backups before you begin any troubleshooting session.
     So I was told to perform the following instructions, which I did, line for line. The part about closing Server.app seems a given, but I'm not sure why they want you to open Server.app at the the end (maybe taken out of context from some other instructions?). I did it anyway, but you should be able to begin testing, on a client workstation, right after rekerberizing is complete. I did, however, need to reboot my client, login as local admin, and then binding would proceed, and network users are able to login again. The engineer also let me know to expect an error, something like the following: "2015-03-11 21:58:38 +0000 Error synchronizing removal of attribute draft-krbPrincipalACL from record 72519e4c-7ac7-15e4-bd42-10adb1944cbc: 77013 result: 16 No such attribute" - this is apparently normal, and did in fact happen in my experience.
So here's the fix:
- Quit Server.app (don’t just close the window)
- On the Open Directory Server, execute these Terminal commands:
- sudo mkdir /var/db/openldap/migration/
- sudo touch /var/db/openldap/migration/.rekerberize
- sudo slapconfig -firstboot
- Open Server.app
And that's it. I did nothing else on my OD server, just logged out. Immediately tried binding on my MacBook client, it failed, I rebooted, tried again, it worked quickly, and I'm able to login with network user accounts again.

Struggle with tiff2icns command

Ladies and gents,
I'm playing around with tiff2icns command and unfortunately not having much of luck despite it is pretty simple command.
When I do "tiff2icns filemane.tiff filenime.icns" it creates empty .icns file.
But if I use -noLarge argument then I do get at least feedback "tiff2icns: no appropriate images found. writing empty file"
I tried couple of tiff files, different resolutions etc...
A bit stuck... Can someone advice?
Thanks.
Regards,
Kris M

Hello Kr15_UK,
It may be that the command is not able to locate any images that match the image sizes listed below.
Searches for 48, 32, 16, 128, 256, 512, and 1024 wide images (in that order) and converts them to icons. Doesn't do any scaling, doesn't generate mini (12x12) icons. If no 32x32 image was found, and the -noLarge flag was not passed, one is generated by scaling the image.
TIFF2ICNS(1) BSD General Commands Manual
https://developer.apple.com/library/mac/documentation/Darwin/Reference/Manpages/ man1/tiff2icns.1.html
Cheers,
Allen

Disable MyBrowserBar Network Error Assistant

How do I Disable MyBrowserBar Network Error Assistant. Browser does not redirect when I click on a link and says I need to Disable MyBrowserBar Network Error Assistant to continue.
Thanks.
=====Question moved to Firefox for Desktop category -feer56=====

All the instruction there are made for Windows users. Firefox Mac doesn't show any "Option" button on toolbar ! Nothing either in Firefox Prefs...

How do I enable flash and java on firefox23 as I have the latest versions installed yet the plugin page shows "disabled" with no option to enable

I have updated to Firefox 23 and it disabled my Java and Flash plugins. I then updated these to Flash 11.8.800.94 and Java to Version 7 Update 25. Now these are showing up on the plug in page but are showing "disabled" with no option to enable. How do I enable them to view content on the web.

Thanks Philipp but i have already done that and the content started working...
However, when i closed and restarted the browser it returned back to the same settings...
I dont think that should happen, but anyway thank you for the solution. At least I can use it by resetting the values if need be
Appreciate your help

I have a problem with my iPhone 5 stopped working the sleep / power and simultaneously refused to obey the HOME button. I can not use either one or the other. I can not enable or disable the device, display lights up when you plug the charger. same displa

I have a problem with my iPhone 5 stopped working the sleep / power and simultaneously refused to obey the HOME button. I can not use either one or the other. I can not enable or disable the device, display lights up when you plug the charger. same display works fine as it is surprising. or maybe someone knows what is the reason for this? is there any way to solve this problem?

More than likely its a hardware issue, I have never encountered such a problem and best bet is to just go get it replaced. If you have insurance on your device apple will replace it as long as there was no water damage, if you dont have insurance they will charge $200 more or less. Hope you get it fixed

How to get slideshow to Pause and restart with auto play enabled? all slideshow do not restart!

How to get slideshow to Pause and restart with auto play enabled? Happening in all slideshow do not restart once one photo is selected

I agree cwclark, I was going to ask the exact same thing, and yes, the only way to 'restart' the auto play is to reload the page which is frustrating to say the least. Every other site I've seen with this kind of 'auto-play' slide show still auto-plays even after clicking the 'next' or 'previous' buttons. Adobe, you need to get a fix for this ASAP

Not null and enable or disable column in tabular form

Hi,
Using apex version 4.1 and working on tabular form.
ACT_COA_SEGMENT_MAS is Master table
and
ACT_SEGMENT_VALUES_MAS is detail table
I have entered 8 rows in master table and PARENT_SEGMENT_ID is column in master table which is null able. If i specified PARENT_SEGMENT_ID with value in master table then in detail table there is column PARENT_ID that should not be null and enable.
How i can enable or disable column when in master table PARENT_SEGMENT_ID column is null then in detail table PARENT_ID column should disable and vice versa.
I have created tabular form on Detail table. before insert into the tabular form Check in master table in first entry if PARENT_SEGMENT_ID is not null in first row of master table then in tabular form PARENT_ID should enable and not null able in corresponding to this first row id's lines in tabular form.
Same should check for second row in master table if PARENT_SEGMENT_ID is not null then entered rows with PARENT_ID into tabular form corresponding to 2nd id in master table should not nullable and column should enable in tabular form.
Thanks & Regards
Vedant
Edited by: Vedant on Jan 9, 2013 9:12 PM

Vedant,
You need to create you own manual tabular form and not use the wizard.
Using APEX_ITEM api you should be build you own form and you will be able to control how you wan to display the rows. (See Link [Apex Item Help|http://docs.oracle.com/cd/E37097_01/doc/doc.42/e35127/apex_item.htm#CACEEEJE] )
select case when PRIMARY_TABLE_COLUMN is null then APEX_ITEM.DISPLAY_AND_SAVE(3 , DETAIL_COLUMN ) else APEX_ITEM.TEXT(2,detail_column) end "ALIAS" from detail table
Hope that help.
Vivek

Problems with .ARW files and auto toning

problems with .ARW files and auto toning
let me try to explain this because this has happened in past and never found a way to resolve but i lived with it
now that I have a Sony A7R the problem is more serious
Firstly i take pride it making the picture happen all in camera, i use DRO lvl 5 to get enough light, like when i'm shooting at dusk. DRO its like doing HDR but in a single file, it lightens the darks. in my camera i'm happy with results
but when I upload them to lightroom, they come out near black.
allow me to explain
lets say I import 100 images
i double check my preferences and everything is UNCHECKED when it comes to importing options, there is no auto toning, nothing.
as the images import i see a preview in the thumbnail which looks fine.
i double click on one to enlarge it, hence leave grid view.
for a brief 1 or 2 seconds, i see the full image in all its glory but than lightroom does something funny, it darkens the image
one by one as it inspects each image, if it was a DRO image it makes it too dark.
to make this clear, the image is perfect as it was in the beginning but after a few seconds lightroom for some reason thinks it needs to correct it.
how to prevent lightroom from doing this, i want the image exactly as it is, why must lightroom apply a correction>?
i think it has to do something with interpreting the raw file and lightroom applies its own algorithm.
but here is what i dont get.....before lightroom makes the change i'm able to witness the picture exactly as it was taken and want it unchanged..
now i have to tweak each file or find a profile for it which is added work.
any ideas how to prevent lightroom from ruining my images and just leave them as they were when first detected...
there are 2 phases...one is when it originally imports and they look fine
second is scanning each image and applying some kind of toning which darkens it too much.
thanks for the help

sorry thats the auto reply message from yahoo email.
i've disabled it now
thing is, there is no DRO jpg to download from the camera
its only ARW. so my understanding is when i use DRO setting, the camera makes changes to the ARW than lightroom somehow reads this from the ARW.
but then sadly reverts it to no DRO settings.
because i notice if i take normal picture in raw mode its dark but if i apply dro to it, it comes out brighter, yet when i d/l the image from camera to lightroom, which is an ARW - there are no jpgs. lightroom decides to mess it up
so in reality there is no point in using DRO because when i upload it lightroom removes it.
is there a way to tell lightroom to preserve the jpg preview as it first sees it.
its just lame, picture appears perfect...than lightroom does something, than bam, its ruined,.
what do i need to do to prevent lightroom from ruining the image? if it was good in the first place.

HT201299 Not enable or disable cellular data for certain iOS apps and features from setting? I keep it off but when I go to other app it on automatic

I can't enable or disable cellular data for certain iOS apps and features from setting.
When I off data for specific application and go to other option it automatic on all application
Any one can help

SOLUTION! (NO NEED TO RESET YOUR IPHONE SETTING!)
I have the same issue for the last two weeks. But i have already managed to solve the issue all by myself. When i go to Settings > Cellular > below the tab "use cellular data for:", i turned off some apps which i didnt want to use with cellular data. As soon as i go back to Settings, and then i went back to Cellular, the apps which i had switched off earlier, automatically turned back on.
Here's the solution:
Either you're using wifi or cellular data, first of all you're gonna hafto turn on the cellular data use for App Store. Once you have turned it on, go to App Store application. Update ALL the apps which have new updates available. If it asks you to log in your App Store, just do so. If there's something wrong with your debit or credit card information, it will ask you to update to a different card. Just do what it asks. Put in a new credit or debit card info and fill in the forms provided. The card you're using must be usable and has usable balance in it. Let's say atleast $10 to $20. As soon as it confirms your card successfully, the app updates will start automatically. Continue to update all the apps. After all updates are finished, go back to Settings > Cellular. Try to switch on or off some apps for data use and recheck.
Try it yourself! Have a nice day and don't put a blame on Apple for this.
From Malaysia, with love.
Please hit LIKE button if this solve your issue. Thank you very much! (:

BGP and auto-summary enabled or disabled with "network" command

Similar Messages

Maybe you are looking for