BGP ASA sample configuration if anyone able to establish tunnels with AWS
Can someone please share their BGP configuration (excluding any key/sensitive information) if they are able to establish tunnels to AWS?
Hi,
Please try to use the command below to verfiy if name resolving works properly.
nslookup
server IPv6 address of the DNS server configured in DirectAccess
internal domain name
If timeout occurs, please check if the IPSec session has been established.
We can verify this in the Windows Firewall--->Advanced settings--->Monitoring--->Security Associations.
If the session has not been established. Please make sure that Windows Firewall is enabled on all profiles in the server.
If the firewall is enabled, please try to enable the auditing of IPSec. It may give some hints.
auditpol.exe /set /SubCategory:"IPsec Main Mode","IPsec Extended Mode" /success:enable /failure:enable
For detailed information, please refer to the link below,
DirectAccess Client Cannot Establish Tunnels to the DirectAccess Server
http://technet.microsoft.com/en-us/library/ee844114(v=WS.10).aspx
Best Regards.
Steven Lee Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Similar Messages
-
I have some music videos on my i-pad. when I play one, the music plays but the video does not. I go under "music video" play list select and play, i get music but no video. Can someone be so kind as to help me. this problem just started today.
Thanks Johnathan for trying to assist. I purchased these music videos from i-tunes, in the past I just had to go into "Music" on the I-pad and select "music videos" then the one I wanted to play and it would just start playing with video. I don't see any "VIDEO" app. These music videos was downloaded from i-tunes and shold play through the i-pad music app. Any further suggestion?
-
since updating itunes yesterday I now can't open it and get a pop up box about the procedure entry point not being located. anyone able to help?
these are the boxes that open up:
I am unsure as to wether I need to unistall and start again but then worry about the vast amount of songs already in the folder that I would have to reload.anyone able to help me with the above?
-
Please gives sample configure VPN site to site on ASA 5512-x v.9.1!
Dear All,
Could you gave sample configer ASA 5512-x v.9.1 for VPN site to Site, i use to configure on ASA 5510 V.8.2 but on ver 9.1 i never configure.
my is use that i dont know to how to configure nonat.
i saw some configration as in the attach file they just to show configure VPN but we did not see nonot on command.
http://www.cisco.com/en/US/docs/security/asa/asa91/configuration/vpn/vpn_site2site.html
Best Regards,
HKHi,
The new configuration format for NAT0 / NAT Exemption / Identity NAT is the following
object network SOURCE-NETWORK
subnet
object network DESTINATION-NETWORK
subnet
nat (inside,outside) source static SOURCE-NETWORK SOURCE-NETWORK destination static DESTINATION-NETWORK DESTINATION-NETWORK
In the above
SOURCE-NETWORK contains the network on your side of the network
DESTINATION-NETWORK contains the network on the remote side of the L2L VPN
The NAT configuration presumes that you are using interfaces with the name of "inside" and "outside"
The reason you see 2 of each "object" in the NAT configuration is that there is no NAT performed for them. You would have option to do NAT for both source and destination but in this case we dont want that.
Depending how many source and destination networks we are talking about, this might need some modifying.
Hopefully this helps
- Jouni -
I have an old airport express ( 1st one ever I think) up until today I was able to use it with iTunes and also Airfoil to stream music. Today I cannot stream music from my MacBook Pro 2008 ( OS X 10.8.3) Airfoil sees the Airport Express but cannot connect, iTunes see it, but will not connect. When I try to connect with Airfoil the error message is "Airfoil was unable to connect to the remote speaker "little fish". Please check the remote speaker and try again."
iTunes just tries to connect and then times out.
I have AU 5.6 in order to use the old AE. It sees the AE and give me a summary page. But if I try "manual set up" or the "continue" button - I get "reading the Airport Express configuration" and then eventually "An error occured while reading the configurarion. Make sure your Apple Wi-Fi base station is plugged in and in range of your computer or connected via Ethernet and try again. (-6753) "
I tried a soft reset, no help.
I tried a hard reset and I was able to see the new airport express and it allowed me to set it up again, then it restarted and everything was the same as before I reset.
I can stream to the Airport Express from my iPhone and my iPad
Does anyone have any ideas on what could be wrong?It appears that the printer is OK and is on the network. Eventually you may want to set a static IP address for it, but let's get things working first.
The first thing I would try would be to reset the printing system on all the problem Macs:
- Sys Prefs, Print & Fax
- Right (control) click the print queue area and select Reset Printing System.
- Select the plus sign to re-add it. Look for the printer, select it and wait until the "Add" button becomes available. Click it.
If this does not do it there may be something going on with the router. I have a few ideas if this is required. Let me know.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
Linksys WRP400 - VoIP Sample configuration guide for VoiceMeUp
Thanks to Linksys for that fine device. Few installations so far with this device and it has prooven his stability and reliability.
Note: Good T38 support and excellent QoS.
Here is a sample of configuration to VoiceMeUp
Linksys WRP400 - Sample configuration guide
[english] - [français]
Enjoy!
For more informations about VoiceMeUp VoIP services, please visit us at voicemeup.com
Message Edited by NothinElse on 08-25-2008 01:09 PMClearly this is too late to help you, but since this is showing up on Google and there are about a thousand views, this answer might be helpful to another.
Once you access the Voice Admin menu and provision your device for your VoIP provider, access to the Voice menu is subsequently "Locked".
Your VoiP provider's system has set a new unique password for the Voice menu once the provisioned device has synced with your providers system.
You should be able to get that password from the control panel on you VoIP account profile under "equipment" or a call to support or an e-mail request should garner the password.
The Login will be "admin" and the password provided will get you back into Voice menu system.
You will also need this password if you want to reset the Voice features back to factory defaults. Because of this system it appears that a WRP400 cannot be unlocked by merely using the reset button. -
Sample Configuration For Ethernet over MPLS.
I am looking for a sample configuration and scenario for the Ethernet over MPLS.I would appreciate if I get some explaination with it.How the LDP is configured for the directed sessions (as per Martini draft) and the auto discovery (as per kompella draft) with respect to Ethernet over MPLS.Cam anyone help me in this ?
Here's a sample EoMPLS configuration on the PE routers:
R1:
interface Loopback0
ip address 1.1.1.1 255.255.255.255
interface Ethernet0/0.10
encapsulation dot1Q 10
! 10 = vcid must match the vcid configured on the other side
mpls l2transport route 2.2.2.2 10
R2:
interface Loopback0
ip address 2.2.2.2 255.255.255.255
interface Ethernet0/0.10
encapsulation dot1Q 10
mpls l2transport route 1.1.1.1 10
The LDP directed session will be setup automatically by the router when the xconnect statement is configured.
Cisco IOS doesn't support the Kompella Draft.
For more information, see the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/atomt/ftatomtb.htm
Hope this helps, -
QoS Sample configuration: Catalyst 6500-E
Dear Experts,
I'm looking for sample configuration documents for configuring QoS on Sup2T with IOS 15.1 SY.
Cuold you point me to appropriate documents please.
SPort is configurable with QoS service policy.
Unable to configure VLAN with QoS service policy.
6506E-2T#
interface Vlan112
ip address 10.112.112.1 255.255.255.0
end
6506E-2T(config)#int vlan 112
6506E-2T(config-if)#service-policy type lan-queuing input INGRESS-1P7Q2T
HQM not supported interface Vlan112MQC features are not supported for this interface
Anyone come accross this please?
platform qos vlan-based is not available in config listing.
(config)#platform qos ?
10g-only qos pure 10G mode
aggregate-policer Named aggregate policer
marking marking keyword
police police keyword
protocol protocol keyword
queueing-only queueing-only (no QoS rewrite, no policing)
rewrite packet qos rewrite enable/disable
service-policy global policy map name
statistics-export qos statistics data export
Testing on 6506-E, Sup2T, IOS15.1SY.
SS -
i am trying to download i tunes to my laptop which is running on windows 8. However everytime i try to instal it, i get a message saying there were errors and i tunes is not configured. my system is not modified, can anyone help.
Hi sarah0407,
Welcome to the Support Communities!
The article below may be able to help you with this issue. You may need to remove more than just the iTunes software. Click on the link to see more details and screenshots.
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
http://support.apple.com/kb/HT1923?viewlocale=en_US
Cheers,
- Judy -
ASA 5505 configured for WebVPN connecting to Citrix Web Interface
ASA 5505 configured for WebVPN connecting to Citrix Web Interface.
i have a ASA 5505 that I am attempting to configure for WebVPN with passthrough into Web Interface . The user authenticates into WebVPN OK and gets the option to click on the Citrix Link (which is i add bookmark citrix server http:// 172.30.40.5.) i enter the citrix and then for example i want to open to outlook it can not open. (when i want to open some application no application is open)).there is no alarm at asa. how i solve this issue?
thanks.Teymur,
Can you confim that after disabling the ssl/tls on the Citrix server (secure connectivity) that you are getting exactly the same error. It is possible that it is generating a different error.
The bug where we have see the existing error was CSCtf06303 but that has been fixed in 8.4.1. Can you confirm the exact version of code you are running on the ASA.
If you have confirmed the above two notes it may be adventageous to open a TAC case as we may need to do some live additional troubleshooting.
Thanks
-Jay -
ASA VPN configuration question
I am trying to configure a VPN tunnel to a remote 3rd party site from an ASA. I have set up a new tunnel group
But it seems to be trying to use the DefaultRAGroup and then the Defaultl2lGroup one. What do I need to do to ensure it uses the new one I have set up ?The name of the tunnel-group has to be the ip address of the remote gateway. With that, the ASA can match the IPsec packets to the correct tunnel-group.
-
Hi all
I bought a second hand mac (boo i know but i am a student so cannot afford a new one!) it is a 2009 model, 15" with 8gb memory
It works fine until a point where it randomly switches itself off! I can be watching something, on photoshop, on iphoto or anything really and it just powers off.
I have found lots of threads saying the same except my mac switches itself back on automatically afterwards.
I have had the fans and filters cleaned and checked. It does not overheat (i have a cooling thing it rests on) and i dont have it working for hours on end before it does this, sometimes it will only be within 1o minutes of me turning it on!!!
Please help!
is anyone able to shed some light?
Also, i hope this problem is solvable personally because i dont have any warranty!
ThanksTried resetting SMC?
Reset SMC.
http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".
Best. -
I have a MBP 13-inch, Mid 2010 and have just upgraded to mountain lion and am trying to connect it to my apple tv however i dont get the air play icon on my mac i have followed all the advise on support anyone able to help??
stevie, a third party app called airparrot will give you the pretty much the same as mirroring and forks on Macs too old to mirror.
-
My gmail doesnt load on my macbook pro anymore, only able to fully load with the html version. Anyone share the same problem?, My gmail doesnt load on my macbook pro anymore, only able to fully load with the html version. Anyone share the same problem?
It loads till the almost the end of the bar and just stops there.I'm having the same problem. It just freezes and wont load the rest of the way.
-
I bought a cd with Lightroom 5. After installation and registration I am not able to use 'help' function and I cannot update the software. Is anyone able to give me a hint how to handle it?
Thank you in advance
arlHi Keith, sorry for my late reply.
Surely I am able to connect to the help function when Icontact the website
of AdobeLR5.The problem is as follows,
When I open LR5 on my computer and work with it and try to open the help
function in the software, I don't get it.
When I bought the CD I was naiv enough to believe that I get an independent
working software. I learned in the meantime, that the seller does not allow
to work with, without being connected to them.
I don't believe that I am paranoid, but I like to buy something and use it
without to inform the supplier that I do it. Otherwise I could have bought
the license fpr LR5 via internet.
Best regards
Karl
2015-01-02 13:42 GMT+01:00 kglad <[email protected]>:
I bought a cd with Lightroom 5. After installation and registration I
am not able to use 'help' function and I cannot update the software. I
anyone able to give me a hint how to handle it? Thank you ind advance Karl
kglad <https://forums.adobe.com/people/kglad?et=watches.email.outcome>
marked Keith_Reeder
<https://forums.adobe.com/people/Keith_Reeder?et=watches.email.outcome>'s
reply on I bought a cd with Lightroom 5. After installation and
registration I am not able to use 'help' function and I cannot update the
software. I anyone able to give me a hint how to handle it? Thank you ind
advance Karl
<https://forums.adobe.com/thread/1669640?et=watches.email.outcome> as
helpful. View the full reply
<https://forums.adobe.com/message/7059196?et=watches.email.outcome#7059196>
Maybe you are looking for
-
How to get video out on HP Touch Smart 600-1050
Hey i would like to see my computers screen on my hdtv but it doesnt seem that my computer has a vga out port. Is there any other way that i can get video out on this PC.
-
Delete or update a line in a text file
Hi, I've got one problem and I hope anybody can help me. I read a text file like this : montext = 20204578 montext2 = 22132546 montext3 = 31321321 I want to know how I can delete or update a specific line in my text file. thanks a lot.
-
XML output from Repostiory Reports
Hi, Any ideas why the table definition report (cktci.rdf) data from the Repository Reports cannot be generated to XML? I'm running Designer ver. 9.0.2.91.9, Reports ver. 9.0.2.0.3 . XML is not on the destination format list in Repository Reports, but
-
Report takes long time to loadq
Hello, I am a developer and have to analyse the behaviour of CR concerning a certain report: It takes about 7 seconds to load this report into the designer and I am wondering, what could cause this delay. Just to make sure: I am not talking about ren
-
HT203521 Note field data deleted for all calendar events
All information at Note Field in calendar events as deleted. All remain information is there. Is there any issue at iCloud? How can I get back this information? Regards Edison