Big Problem when Capturing DVCPro 50 tape with FCP 5.0.4

At the job we work with DVCPro 50 tapes wich I capture using the capture Preset DVCPro 50 NTSC, the images are perfect, but there is a problem with the sound it doesn't capture at the good frequence, exemple, if the capture provide 5 clips, the 3 or 4 first will be fine and the other one qill be at an audio rate of 47.* instead of 48 khz, does anyone had that problem already and if so, what can i do?? Cause now everything is off sync
thanks

sorry to bother you, but you were the only reply. 3 sources were mini dv. 1 was hdv. the mini dv sources were converted using toast (by someone else). when all sources were put on the timeline, i got the redline render. so i rendered them (took many many hrs). then i exported them. this turned them into
fcp movie files. then i re imported them. currently the browser says they are all dv/dvcpro, ntsc ccir601, 720x480. the weird thing is that i can multiclip any of the two sources, but not 3 or more. any help would be appreciated. thx dr

Similar Messages

Can FCP7 Regen Time Code when capturing from tape to allow for TC Breaks?

Can FCP7 Regen Time Code when capturing from tape to allow for TC Breaks? Or does it start capturing with time code from the tape and then just keeps rolling regardless of TC breaks on the tape, thus not matching code after the first TC break? I don't see any preferences where you can ask it to regenerate the code it is writing based on the code it's receiving from the tape (i.e. continuous jam). I'm guessing it just keeps on going with the code it started with. Anyone know different?
Thanks!

It is not clear from your post what you want FCP to do when it encounters the timecode break on the tape that it is ingesting.
You have three choices:
If you choose "Make New Clip" then FCP will stop, roll the tape forward to legitimate code, and then attempt a pre-roll and start capturing again. The new clip will have timecode that corresponds to the timecode on the tape.
If you choose "Warn After Capture", FCP will keep ingesting and the timecode will continue contiguously from the source code of your starting clip, meaning it won't match the tape after the point of the break.
MtD

Problems when capturing HD

I have Macbook 1.83GHz Coudue1,and I bought 3 year plan.
My macbook has big problem when importing HD from my SONY HDV camera. The sound is not going along with the picture,and the sound is streched,slow,and strenge. I updated everything into the lastest version,and reinstalled the imovie,but still the problem exist.
I believe is the hardware problem,and many many macbook Coudue1 has.I did the same on Coudue2,it has no problems at all.

http://www.youtube.com/watch?v=2ahsaaKQfQI
I posted the video about the problem in details.
I tested on all macbooks coredou1 in apple fix centre,the result is the same,just like mine.

ORA-00600 problem when create XMLType table with registerd schema

Hi,
I am using Oracle9i Enterprise Edition Release 9.2.0.4.0 on RedHat Linux 7.2
I found a problem when I create table with registered schema with follow content:
     <xs:element name="body">
          <xs:complexType>
               <xs:sequence>
               </xs:sequence>
               <xs:attribute name="id" type="xs:ID"/>
               <xs:attribute name="class" type="xs:NMTOKENS"/>
               <xs:attribute name="style" type="xs:string"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="body.content">
          <xs:complexType>
               <xs:choice minOccurs="0" maxOccurs="unbounded">
                    <xs:element ref="p"/>
                    <xs:element ref="hl2"/>
                    <xs:element ref="nitf-table"/>
                    <xs:element ref="ol"/>
               </xs:choice>
               <xs:attribute name="id" type="xs:ID"/>
          </xs:complexType>
     </xs:element>
Does Oracle not support element reference to other element with dot?
For instance, body -> body.content
Thanks for your attention.

Sorry, amendment on the schema
     <xs:element name="body">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="body.head" minOccurs="0"/>
                    <xs:element ref="body.content" minOccurs="0" maxOccurs="unbounded"/>
                    <xs:element ref="body.end" minOccurs="0"/>
               </xs:sequence>
               <xs:attribute name="id" type="xs:ID"/>
               <xs:attribute name="class" type="xs:NMTOKENS"/>
               <xs:attribute name="style" type="xs:string"/>
          </xs:complexType>
     </xs:element>

Problem capturing DV tape to FCP 10.1.3

New to FCP X and having problems importing the entire tape.
Importing dv tape using Sony SDR-11
OS X 10.9.4
Processor 2x2.66 GHz 6 Core Intel Xeon
External Hard Drive 1TB (set up for FCP media storage)
Currently the footage is importing in small increments of 2-3 minute clips and I am trying to capture the entire tape.
Any suggestions would greatly be appreciated as I have been not been able to figure this one out.
Liza

Ross
I am trying to import 50 mins or so of a lecture. One continuous shot. No stopping or starting of camera.
Fcp will only import small increments of the tape. The clips are never of the whole lecture even if I tried
To edit them together. If only I should be happy at this point.
I really dont know what to do. Every tape I try to import ends up with small increment clips. After the import the message always says tape has been entirely imported. But this is incorrect.
I have even gone to the manual and no help there.
How did you fix your problem?
Thanks for you input.

Capture DVCPRO tapes in Final Cut

I have a Sony HVR-M15 series tape deck and FCP 6. My deck captures mini-DV media via firewire in FCP no problem. The deck also has the capability to handle the bigger DVCPRO tapes. I can play the DVCPRO tape just fine on my monitor but when I try to capture it FCP freezes or sometimes gives me an error message (this operation cannot be completed as there is no video). Any ideas?

Hi thanks for all your posts,
It looks like it is a compatibility issue with the deck. It still doesn't make sense that I can play the DVCPRO tapes but not capture them. http://www.globalmediapro.com/video/products/SonyHVRM15_HDVRecorder--1948.html This is my deck, and a list of the stuff that's compatible with it. It appears like the HD DVCPRO tapes are compatible so it seems like the normal ones should be.

Audio unsynced with video when capturing analog HD with Kona LHe card!

Hey,
This is kind of an emergency because i am in the process of logging a feature film. I am using the Kona LHe card to capture analog audio and video with the JVC BR-HD50 HDV deck. It is 720p24 HDV footage converted to analog DVCProHD 720p59.94 footage through the Kona. My issue is that the audio is about 4 or 5 seconds unsycned with the video...I am also getting some audio popping. The audio sounds fine when listening through the line mixer but it pops when i play back though FCP. I already contacted AJA (the makers of Kona) and they its a FCP problem...Any prompt help would be greatly appreciated...
-JE

Welcome to the forums!
What version of FCP are you running? If you can, get to the most current version as this solves a lot of issues with the DVCPRO HD codec.
And have you read this whitepaper?
http://www.aja.com/pdfs/AJAwhitepaperHDV.pdf
Shane

Problems in Capturing NTSC VHS With a PAL MSI nVidia Personal Cinimea FX5200

I live in Europe which as most of you know uses PAL format. Most European VHS machines will play NTSC VHS in a format caled PAL60. The FX5200 Personal Cinema card will only play a PAL60 format color NTSC VHS tape in black and white. Which means that in order to convert NTSC VHS to digital video, you have to have an NTSC VHS player in order to input a "pure" NTSC signal to the card.
Having purchased an NTSC video in the US on a visit there, I now encounter the problem that you see in the image I have posted here.
This was a oddly enough black and white film that I have captured but the effect is the same with a color film. The image will "blink" to a sort of negitive form of the image.
It only covers the left half of the image and this occurs regardless of which recording software I use. I tried deinterlacing but that didn't help either. It usually occurs at the start of a recorded VHS recording and flashes for only a second but it can persist through an entire VHS recording.
If I run the VHS directly into my TV set, which can play NTSC video, this doesn't occur. When I record, I use the iuVCR recording programand compress the avi files withTMPEGnc. But if I use the software that came with the card, the samething happens.
Does anyone have any ideas?

i am getting same problem but i only get this problem when i have tv out enabled this is happenning in other programmes as well like nvdvd and power dvd . powere dvd is not recognissing graphics card in tv out mode when hardware accelaration is activated. i have tried all possible setting s and will not sort problem out. in standered 1 monier mode everything is fine no stuttering or picture problems. i think it is driver issue. :O

Firewire failure when printing to tape with DSR-11

I have a problem printing to tape with bigger projects. I can't put out to tape more then around 20mins, then the either sound or sound and picture drop.
I have everything rendered and exported to a new, not-selfstanding final cut pro file (Quicktime export) and reimported and put in a new sequence. As I found out, this causes the least problems with complex sequences, sounds etc.
The problem might be related to a occasional image drop out while working on the timeline and watching on the external monitor (through firwire). After a while the connection fails and I have to switch from "all frames" to "none" and back in order to continue watching through the deck.
I checked all settings I know, could it be a hardware problem or a problem with the protocoll of the sony DSR-11 deck (I use DVCAM).
Thanks for your time !
klaus

Hello Klaus,
I also own and operate a Sony DSR-11 which has worked out just fine for me. However, I recently bought a new firewire cable to replace my 4-year old cable and discovered that you get what you pay for when it comes to cables. After a while the new cable would slip out of the back of the DSR-11 and I would lose my connection during editing and playback. As part of the troubleshooting process I replaced the firewire cable with a "better" one and no longer experience this problem. My only critisism of the DSR-11 is the smaller firewire connection instead of the larger one found on external firewire devices. Good luck.
Steve

Problem when creating a Form with Launch Task Form Wizard

Hi all,
I'm using jdeveloper 11.1.1.6 over Windows 7 64bits for my BPM project.
I'm a new with BPM and i have a problem when trying to create a task's Form with the "Launch Task Form Wizard". I'm trying to create my Form based on a custom template, i already have imported the template as a library, now after i have selected the template i follow the wizard and i reach the wizard's rowX-columnX where i should choose the field i want in my form, but the problem is that i don't see any fields in that part of the wizard, the window is empty :(
I have created a business object based on a XSD, then i created a process data object based on the previous created business object and finally i used this data object as a parameter to the human task.
What could be my problem ?? :( :(
Regards
Carlos

I have also faced this issue few times. There could be a namespace issue / schema issue. Please check if you are able to see task:task in the schema section anywhere in the .task file you created. If that is not shown, the fields will not appear while creating human task form.
Thanks
Ashwini

Capturing DVCpro 50 into FCP 5

I am new to DVCpro50 and 24p and can't, for the life of me, get the deck (Panasonic SD93p) to read in FCP 5. I've got the firewire connected, but neither the computer (G5), nor the deck are registering that there is any sort of connection. Can anyone help me with the settings so I can capture this footage before I throw both the deck and the computer out the window?

Hi again,
Oops... sorry, not sure, confused that. But the following information might be helpful:
https://eww.pavc.panasonic.co.jp/pro-av/saleso/ieee1394/AJ-SD93PFCPHD45.html
There was an excellent thread on the SD93P with FCP on uemedia.net, but just checked... it has been archived.
Cheers,
Uwe

Problem when creating planned order with MRP run

Hello,
I create a material with a fix reorder point, MRP type VB. When I run MRP with MD03 on this material I have several problems :
- planned order is created with an opening date in the past, so I have error 'Opening date in the past' in MD04. How can I generate a planned order with opening date not in the past
- when changing manually opening date, after running again MD03, I have error 'No BOM selected'. Material is configurable, has a text BOM, a routing and a configuration profile. What is the problem? When modifying planned order, I have message :
Material requires configuration
Message no. 61259
Diagnosis
Orders and requirements for a configurable material must have characteristic values.
Usually, you should create a variation for configurable materials managed in inventory management which has the default variant configuration.
System Response
MRP: Requirements without characteristic values for a material cannot be planned in MRP.
Procedure
Check requirements or orders.
Create a configuration evaluation for the material in the material master record if necessary.
Thanks in advance.

Hi
I am facing the problem. Could you please tell me if you have resolved the above problem? If yes, Could you please provide me as how you resolved? Thanks in advance.
Thanks
Nagesh.

Problem when install Fireworks CS4 with Window XP

I have a problem when install Fireworks CS4
[quote]Adobe Fireworks CS4
Error:
Error 1603. Fatal error during installation.[/quote]
Please help me!
Thanks!

Here is a full technote when having problems with Fireworks on Windows XPPro,... see if there is something there that helps.
Also make sure that you also install the FWs updater:
http://www.adobe.com/support/fireworks/downloads_updaters.html
If nothing helps, then the only thing you can do is contact Adobe Support to see if they can help you.

Problem when trying to sync with Palm Centro phone and Palm m500

I just purchased a Palm Centro phone and have had no problem when I try to sync the phone with the Palm software on the computer, however, my wife has an older Palm m500 and all her contacts are on her Palm, but they don't show up on the Palm Desktop software. Is there something we're doing wrong? All the dates show up on her desk top and everything in my phone shows up on my desktop, only her contacts are empty.
Post relates to: Centro (Verizon)

It is likely that your wife's older device (with Legacy two-word PIMs) is incompatible with the Access Desktop/Hotsync for Verizon Centros as I believe it has only the new Extended (one-word) PIM conduits. If you are running XP you might be able to use a download of 4.1.4e. Suggest you search the Hotsync forum to see if the Centro can use this version of Hotsync (I don't have a Centro).
Post relates to: Palm TX

When migrating intel laptop with FCP 7 to retina laptop should I select "Settings"?

Bought a new retina laptop and want to migrate my intel laptop (OS 10.5.8) with fcp 7 to the new machine. Should I select "Settings" and/or "Other files and folders o Macintosh HD" to migrate in addition to "Applications" and "Users"? Want to make sure FCP 7 will work on new machine. Thanks!

I believe it is unlikely that they would corrupt any more than they usually do, which is not very often if at all. It runs exactly as it did on my Macbook Air running Lion. However I have only just upgraded to a retina MBP running ML in the last few weeks. I uninstalled FCP X at the start of the week in a blind fury when the simple things I wanted to do with it could not be done. and have been on FCP 7 ever since. Most notable gripes are not being able to export using the in/out points, it is really difficult to copy and paste clips from one sequence to another and there is no tabs for sequences. It's like it was made for an ipad.

Big Problem when Capturing DVCPro 50 tape with FCP 5.0.4

Similar Messages

Maybe you are looking for