Big problem with a select using remote database

Hi Guy.
I have a big problem with a simple query, but this is a scenario.
Actuallly I'm in Alexandria - Egypt with a server with Oracle 10.2.0.4 database 32 bit on linux Red Hat as 4.8. the server can connect to another database oracle but 9.2.0.6 installed on Red Hat As 4.5 placed in Milano Italy . Ttwo networks are connected via two adsl cisco router with firewall and Vpn functions. In Egypt there isn't a very good adsl.
In Alexandria, I'm trying to connect to database in Italy with sqlplus. The sqlplus connected I write.. select * from addetti and all work fine.
My problem is that when I try to make the same select on a table with many columns oracle database kill me a session.
My table (ic_lav) is long 174 colums 1924 byte for row. Well when I write a query with select * from ic_lav all oracle close my session.
So I began to change my query I start to
select field1 from ic_lav... and work
select field1,field2,field3,..........field50 from ic_lav and work
select field1,field2,field3,..........field70 from ic_lav and doesn't work
the select work with 68 columns
problem: the query with more then 1064 byte for row doesn't work.
I've tryed with anoter big table with the same problem, but the select fwork with 65 columns...
Iit is obvious that there is any problem with the limit of the query.
The same query (select * from ic_lav) in localMilano)l work fine.
The same query (select * from ic_lav) in vpn with a better adsl line and openvpn software (NO CISCO firewall) WORK FINE.
The same query connectetd in Milano with a vpn make with analogic modem and remote access by windows work fine.
the query (make on my laptop connectet with vpn by cisco doesn't work.
In cisco firewall we haven't any error (cisco man tell me so)
on database 9 I found :
*** 2009-06-12 09:49:45.509
*** SESSION ID:(66.44406) 2009-06-12 09:49:45.497
FATAL ERROR IN TWO-TASK SERVER: error = 12152
*** 2009-06-12 09:49:45.509
ksedmp: internal or fatal error
Current SQL statement for this session:
select * from ic_lis where ditta
----- Call Stack Trace -----
but I don't understand why the lost connection problem (bug 3816595 A processstate dump is produced for a lost connection (12152) ) is caused by len of row
Anybody have some idea ?
Thank you

My table (ic_lav) is long 174 colums 1924 byte for row. Well when I write a query with select * from ic_lav all oracle close my session.Do you get any error?
If the query length is a problem, you could create a view and query the view instead to see if this problem is resolved.

Similar Messages

Windows 8.1 having problems with pinter selection using Elements 13.

I am running Windows 8.1 with Elements 13 and am having problems with PRINT. If I select a printer from the PRINTER menu, Elements recognizes the change of selection, allows me to modify the printer's specific setting and, then, when I PRINT seems to not recognize the selected printer and print of whatever was set as the original printer. Then, I delete the "original" printer in Windows 8.1 and attempt to print again with the same general result except I receive a Printer Not Found error from Windows.
How do I modify the "original" printer setting (seems to be associated with the file)? Note the "original" printer is not the default printer.

Hatstead,
Thank you.
Yes, all of the print drivers are up to date (re-verified last evening).
Yes, I can print and select the printer as normal for all of the standard applications I use (Visio, PowerPoint, Word, Excel, Outlook, direct print from file (Explorer)).
I shortened the printer names from the standard Microsoft convention (based on some of the BOG comments). There was no change. In fact after the test sequence noted in #5, I re-implemented the "name shortening" yet again (shorter yet). I launched Elements and ran into the same messages noted in #5 (obviously, the "stored" printer did not exist). Yet after I went through the printer selection process (again as in #5) and, after a lag time, Elements redirected the print job what was the "stored" printer which was renamed....I do not know how Elements associated the deleted "Stored" printer with its old name with the newly named printer since no other application could (I checked).
I have closed and restarted the PC numerous times.
I have deleted all of the printers except the one I wanted to use for the specific print job. In this case, Elements came back with a message it could not access the "stored" printer. I then selected the correct printer, Elements acted like it was allowing to set up the selected printer with the specifics of the print job, and, then when I went to print, Elements again tried to redirect the print job to the "stored" printer (even though it did not exist).
The target printer is a "local" printer (USB connected). The apparent "Stored" printer is a network printer. So, I deleted the PC which has the "Stored" printer from the network (actually not only deleted it from the devices on my PC but literally shut the PC down and disconnected it from the network (two different test)) to no avail (still got the test results in #5).
Yes, I have attempted to print from the Editor (my normal mode) and from Organizer.
I have copied, open a new file and, then, pasted the image I wanted to print to no avail.
Is the a "stored" printer associated with the file or with Elements? If so, how to I modify (or dis-associate)?
Again, thank you.

A big problem with using endnotes in Pages 5

Unlike Pages 09 which worked flawless with endnotes functionality, Pages 5 has a big problem with the feature that maybe been addressed.
When I insert an endnote, I am prohibited from clicking the citation number at the end of the document which is supposed to take me back to the inserted citation.
Am I doing something wrong here or this is just another invaluable feature removed by Apple?
Please help!!!
Thank you.

It's not a feature I use much, so haven't worked at finding the flaws in the Pages 5 version, but going on just how badly Apple has done everything else in Pages 5 I am not at all surprised. It had problems from the beginning and Apple has take over 15 months to do frankly very, very little to fix anything.
There was much heated debate by certain people on this site who swore blind that Apple would fix everything.
Just remember the definition:
Pessimist: n. Optimist with experience.
Peter

There appear to be big problems with Mavericks Mail, particularly if it's used for Gmail. Have other users noticed that it slows to a crawl and can't reload the contents of a folder instantly....Is there a fix coming?

There appear to be big problems with Mavericks Mail, particularly if it's used for Gmail. Have other users noticed that it slows to a crawl and can't reload the contents of a folder instantly....Is there a fix coming?

There is a large thread relating to Gmail, but nothing that sounds like that.
Nobody here knows what Apple is going to do.
You might try removing the Gmail account and then add it back in.

Helloo! I have super big problem with my Air.

Helloo! I have super big problem with my Air,10.8.5 ,it asks every 10 sec to make some changes and asks me for password all the time!! I cant acces my documesnt,pics,music,NOTHING at all! Finder is not working,i cant open any folder,icons are missing also,i cant open any of them,mozzila,chrome..im really going crazy.. i updated tonight my phone on new IOS 7 through my comp,cant be that i messed up everything because of that..this comp.is like 10 days old.
btw. i created new user,and everything is working ok.

Back up all data. Don't continue unless you're sure you can restore from a backup, even if you're unable to log in.
This procedure will unlock all your user files (not system files) and reset their ownership and access-control lists to the default. If you've set special values for those attributes on any of your files, they will be reverted. In that case, either stop here, or be prepared to recreate the settings if necessary. Do so only after verifying that those settings didn't cause the problem. If none of this is meaningful to you, you don't need to worry about it.
Step 1
If you have more than one user account, and the one in question is not an administrator account, then temporarily promote it to administrator status in the Users & Groups preference pane. To do that, unlock the preference pane using the credentials of an administrator, check the box marked Allow user to administer this computer, then reboot. You can demote the problem account back to standard status when this step has been completed.
Triple-click the following line on this page to select it. Copy the selected text to the Clipboard (command-C):
{ sudo chflags -R nouchg,nouappnd ~ $TMPDIR.. ; sudo chown -R $UID:staff ~ $_ ; sudo chmod -R u+rwX ~ $_ ; chmod -R -N ~ $_ ; } 2> /dev/null
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). You'll be prompted for your login password. Nothing will be displayed when you type it. You may get a one-time warning to be careful. If you don’t have a login password, you’ll need to set one before you can run the command. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The command will take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear, then quit Terminal.
Step 2 (optional)
Take this step only if you have trouble with Step 1 or if it doesn't solve the problem.
Boot into Recovery. When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar. A Terminal window will open.
In the Terminal window, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window will open. You’re not going to reset a password.
Select your boot volume ("Macintosh HD," unless you gave it a different name) if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Under Reset Home Directory Permissions and ACLs, click the Reset button.
Select
 ▹ Restart
from the menu bar.

Big problems with slideshows

Hi, I've a big problem with iPhoto (and Aperture too, but I'll say later).
Two days ago I was creating a small slideshow (18 pictures) and everything was fine. Suddenly, while I was looking for a theme, switching between 3 of them, iPhoto stopped to work. No ESC, no key, I had to restart my iMac, turning it off.
From this moment every slideshow I select, iPhoto stop to work and need a force quit. So I restored a library, from Time machine, but nothing changed.
So I bought Aperture, but nothing changed, using iPhoto Library.
Now I've created an Aperture Library, importing in it my old iPhoto Library. Is there any way to "clean" iPhoto, reinstalling it from new? Do I need such a action?
Thank you and best regards.

That means that there is something in your account that's the culprit. First try the following:
1 - delete the iPhoto preference file, com.apple.iPhoto.plist, that resides in your
User/Home/Library/ Preferences folder.
2 - delete iPhoto's cache file, Cache.db, that is located in your
User/Home/Library/Caches/com.apple.iPhoto folder (Snow Leopard and Earlier).
or with Lion and Mt. Lion from the User/Library/Containers/com.apple.iPhoto/
Data/Library/Caches/com.apple.iPhoto folder
3 - launch iPhoto and try again.
NOTE 1: If you're moved your library from its default location in your Home/Pictures folder you will have to point iPhoto to its new location when you next open iPhoto by holding down the Option key when launching iPhoto. You'll also have to reset the iPhoto's various preferences.
NOTE 2: In Lion and Mountain Lion the Library folder is now invisible. To make it permanently visible enter the following in the Terminal application window: chflags nohidden ~/Library and hit the Enter button - 10.7: Un-hide the User Library folder.
If that fails it might be another preference file that's causing the problem. Here's how to test for that:
Trouble Shooting Preferences
NOTE: In Lion and Mountain Lion the Library folder is now invisible. To make it permanently visible enter the following in the Terminal application window: chflags nohidden ~/Library and hit the Enter button - 10.7: Un-hide the User Library folder.
1 - close all applications.
2 - open your Home/Library folder and Option-drag (copy) the Preferences folder to the Desktop.
3 - select the contents of your Home/Library/Preferences folder and drag them into the Trash bin in the Dock. You will be asked to provide your Admin password.
4 - reboot.
5 - run the application again and determine if the problems is fixed
6 - If the problem is fixed:
A - open the working Home/Library/Preferences folder.
B - Open the Preferences folder on the Desktop, select all of the contents and drag them into the working Home/Library/Preferences folder.
C - When the Copy window pops up check the "Apply to All" check box and then click on the Don't Replace or Skip button.
D - reboot.
7 - If the problem is NOT fixed, drag the contents of the Preference folder on the Desktop into the Home/Library/Preference folder and replace the entire contents that were created by clicking on Replace.
8 - reboot.
OT

Big problem with Airport Extreme and Vivax Provider in Brazil

Hello guys.
I live in Brazil and I bought my Airport Extreme in a recent trip to USA.
For some years I was a client of Telefonica and had an ADSL link, I had a D'Link G604T to do both the modem and router operation in the same box. I was happy with my connection of 1Mbps.
In a recent promotion of Vivax I switched to a cable connection to have both TV and Internet at the same operator, my link now has 3Mbps.
With this pack I also received free one RCA cable modem model DCM425B, it was installed fine in one computer only. Everything was fine my connection was faster the old one.
So I went to install the Airport Extreme to make things even better.
After I installed I went to see the web status of my modem, all parts were looking fine, but the modem could not see the computer. Bad sign.
I talked to Vivax support people and apparently it was a problem with their network setup and they manage to make it right. My model now sees my computer.
After that problem was solved I could not make AE to work with the modem, it had the green light and the setup looked fine, but I could not open any site. I tried to turn off my modem and AE, waited some minutes and turned on first my modem and after it was up I turned on AE. All lights looked fine but again no connection to any site.
I called again the Vivax support center and they tried to help me but the don't know AE and they could not help me with all the details but said there was 2 10.x.x.x coming from my side. So I tried to use in bridge mode. I also selected the 192.x.x.x range instead of 10.x.x.x as default.
After many setups and turn off and on again my connection is working but I have a big problem with wireless. If I turn it on I loose my connection, it seems that AE sends 2 equal ethernet address to Vivax and their network don't like it cutting me off.
So my connection setup is like this:
RCA Cable modem model DCM425B at 3Mbps using a 200.x.x.x ip
Airport Extreme connected to a Mac and a Windows PC by wire using the 192.x.x.x range ip
Wireless is off
Bridge mode is on
This the only way I could make it work.

After a firmware update it worked fine.

Big problem with my 4th Gen, please help !!!

Hi guys.
Well I've a big problem with a 4th gen Ipod. The prob is that the Select button on the middle doesn't work.
I've tried everything : Did a reset, a complet restore from Itunes 7, but it was unsuccesful.
I don't really understand the problem, I was using the Ipod normally then suddenly the button didn't work !!
Please help me. In addition, I cannot carry it to the Apple Centre because I live in Algeria.
Thanks.

No ideas ???
I've tried to open it as well, I've unplugged all the connectors, cleaned it with alcohol, but the button still not responding.
Do you think that the problem would come from the logic board ?? Because the button itself worked (I used a METRIX to test it), and I can make a reset with no problem (the reset needs the central button).
Please help me. Thanks.

Hi I've a big problem with adobe acrobat reader XI pro and I hope you can help me. The problem is; when I past copied text from some pdf books (not all of them) it past symbols only! wherever I past it! and even if I coped that text from another pdf reade

Hi
I've a big problem with adobe acrobat reader XI pro and I hope you can help me.
The problem is; when I past copied text from some pdf books (not all of them) it past symbols only! wherever I past it! and even if I coped that text from another pdf reader (adobe pdf reader, internet browsers, ...etc.).
This problem started to happen since yesterday when I installed adobe acrobat reader XI pro to try it before I buy it, and before that when I was using the free adobe pdf reader I was totally able to copy any text from any pdf and past it anywhere with nothing wrong.
What can I do?
thank you a lot.

There is no product called Adobe Acrobat Reader Pro. There is
- Adobe Acrobat Pro ($$)
- Adobe Reader (free)
Which do you have? And are you a programmer?

I have big problems with mountain lion. you can not have a boot disk system I resulted in the need to re-download the os from scratch impiegandoci 8 hours, it is outrageous even with windows 95.

I have big problems with mountain lion. you can not have a boot disk system I resulted in the need to re-download the os from scratch impiegandoci 8 hours, it is outrageous even with windows 95.
at least that the operator has confirmed to me that he called me. I also have problems with either the start of the mac with the power off. I can not understand if it crashes or is just very very slow.
Finally, I have a problem with the external hard disck. I often said to have been ejected incorrectly (not true) and I start to restore the startup recovery disk because disk utility is ineffective from the normal operating system .. is a shocking thing, but how you reduced. in four years it had never happened. seem to have windows or worse. Wake up.
I am an Italian, alas, and then I would like an answer to my language because my € are the same as German French or English.

You are on Windows 2000, you do not have a "Firefox" button, and should consider yourself to be fortunate in that you still have menus and don't have to do anything to get the menus back instead of the "Firefox" button. (The same applies to Windows XP users).
Use the "File" menu to get to Import. You are not on Windows 7 or Vista, and don't have to put up with the nonsense added for Aero.
If you want the "Firefox" button you can get it with View -> toolbars -> (uncheck) Menu Bar. The menu bar and the "Firefox" button were supposed to be mutually exclusive (which is impossible in some cases without being incompatible).
Once you are using the "Firefox" button ...
Use the "Alt" key to view the menu bar (temporarily) containing File, Edit, View, History, Bookmarks, Tools, and Help. On Windows 7 and Vista, the menu bar was hidden by default in Firefox 4 and above. These menu items are more or less available under the "Firefox" button which has the most used of the built-in Firefox menu items available in a different format.
To get back to having menus again. "Firefox" button -> Options (second column) -> (check) Menu Bar
You can make '''Firefox 7.0.1''' look like Firefox 3.6.*, see numbered '''items 1-10''' in the following topic [http://dmcritchie.mvps.org/firefox/firefox-problems.htm#fx4interface Fix Firefox 4.0 toolbar user interface, problems (Make Firefox 4.0 thru 8.0, look like 3.6)]. ''Whether or not you make changes, you should be aware of what has changed and what you have to do to use changed or missing features.''
* http://dmcritchie.mvps.org/firefox/firefox-problems.htm#fx4interface

Problem with SDO_relate when using polygons with holes.

I'm having a problem with sdo_relate. I'm trying to extract all elements from a point table (bdtq_batim_p) that are inside a specific polygon from another table (SDA_MUNIC_SS). The spatial index for both table have been rebuilt and the data from both table is valid.
When I do a count on the query, I know the answer should be 1422 elements (Counted in ArcGIS). However, sdo_relate gives a smaller number of elements in the result set.
The query :
SELECT count(distinct t.identifiant) FROM bdtq_batim_p t, SDA_MUNIC_SS s WHERE s.mus_co_geo = '48015' and sdo_relate( t.SHAPE,s.SHAPE,'mask=anyinteract querytype=window') = 'TRUE'
returns 282 elements. The query with mask=inside, SDO_Anyinteract() and SDO_inside() all give the same result.
I did a test with the following query and the result is 1422 (which is the good result).
SELECT count(distinct t.identifiant) FROM bdtq_batim_p t, SDA_MUNIC_SS s WHERE s.mus_co_geo = '48015' and SDO_WITHIN_DISTANCE( t.SHAPE,s.SHAPE,'distance=0') = 'TRUE';
It's important to note that the polygone (from SDA_MUNIC_SS) that is used for this query have holes in it. I have the same problem with all the polygons from the SDA_MUNIC_SS table that have holes in it. For the polygon without holes, the results are the same for the 2 queries.
My question are :
Why are the result from the two queries different? A query with a buffer of 0 should always return the same result as a query with Anyinteract.
Is there a known problem with SDO_RELATE when using a polygon with holes in it?
Do you have any idea how to solve my problem.

Since i don't have much control on the version of Oracle and Patches that we use in the system, we used a workaround that detects the polygons with holes and uses the SDO_WITHIN_DISTANCE( t.SHAPE,s.SHAPE,'distance=0') = 'TRUE' operator in those case. We saw a slight decline in performance but it now returns the right results. When the system will be patched, we'll come back to the original version and see if the problem is solved.

Having big problems with Creative Zen Micro Photo!! I need much urgent help!

Hi. I am having a big problem with my MP3 Creative Zen Micro Photo device at the computer.Here is the thing:Before I bought this I had the regular Zen Micro & having fun with it. I had no problems with that when I used the Media Explorer to transfer songs. So I bought the Zen Micro Photo & installed it my computer. As normal I used the Media Explorer to transfer songs & pictures.So I reinstalled Windows XP at my computer, and when I installed the CD that followed to transfer new songs, the Windows said that it's an unknown thing I have connected in the USB.So I installed Service Pack & 2. I have tried to install drivers from the cd but it seems that there are no drivers on the cd! The big problem is that when I connect the MP3 to the computer, it doesn't read it's a Zen Micro, it's just unknown! So the Zen Micro Photo Media Explorer program doesn't work & I can't transfer songs or picture on it! And it just happened after I re-installed Windows on my computer. The same thing happened on my brother's computer after he re-installed windows. And when I connect the MP3 to the USB, it says that it's not a USB 2.0, but .! And I am sure it is 2.0 because it has always been like that before I re-installed windows. Also the MP3 does not re-charge when I put it my computer! The battery is just the same, it tries to do it but it doesn't. So I am using my sisters computer to charge the MP3 & transfer songs. I have tried everything but I can't seem to understand what the problem is? I have never experienced something like this before, and I really hope you can help me with this! To be honest I think what I am missing is the driver. So can someone PLEASE provide me the link for the driver? I have downloaded all those 3 on www.creative.com, but they are none of them! Also that playforsure firmawre thingy does not work because it sais that I have to connect my MP3, and it is connected already!Please reply as quick as possible! Thanks a lot for you kind help!
I have also sent this mail to creative support! But please help me I have had this problem for almost 2 months now! =(Message Edited by anakwalajinn on 05-0-2006 08:47 PM

Might try this:? http://forums.creative.com/creativel...mp=true#M95059

Big Problem with Mighty Mouse

I'm having a rather big problem with my wired Mighty Mouse. Basically, the middle button is the only top button that works, and clicking with the left or right side does nothing but activate the middle button instead.
Here's the nitty gritty...
The reason I can assume this happening is because I cleaned the scroll wheel to un-stick it. I did this by getting a sheet of white paper, turning the mouse upside down, and rubbing the wheel all over the paper, which left paths of dirt and fluff everywhere. Worked great, and the scroll wheel now works perfectly again.
The mouse worked fine after that which is what makes this problem odd, but later that night, all the top buttons just started acting as one middle button... So, (using my tablet) I changed the setting for the middle mouse button in the preferences to 'Primary Button'.
Now basically what I have is a one button mouse (with side squeezy things).
How do I make the left and right buttons work again? The preferences are set up fine... as in the right side is assigned to 'Secondary Button', etc, but it still only works as middle mouse.
Any ideas or help would be really appreciated!
Cheers
Cuby

If you are going to replace it, consider getting a plain old optical mouse that uses Apple's built-in generic USB mouse driver. I like the ones from Microsoft that have two buttons, a clickable scroll wheels, and that's it. This is the one that I use now.
[Microsoft Optical Mouse (Blue)|http://www.amazon.com/Microsoft-K81-00004-Optical-Mouse-Blue/dp/B000068M P2/ref=sr11?ie=UTF8&s=electronics&qid=1244701238&sr=8-1]
It is reliable, comfortable, and sturdy. I've never cleaned it. And it's so cheap. I had a different basic Microsoft mouse before, and the only reason I got a new one was because I wore out the pads on the bottom that let it slide around.
Tip: Apple's generic USB mouse driver does not seem to have way to set the center button click. But if you set it to something when the Mighty Mouse is connected, that setting seems to continue to work with the generic mouse. Mine is set to do Exposé.
Not sure why you cannot do +reset PRAM+. If your internal speaker volume setting is muted so that you do not hear the startup sound, you need to turn up the volume a bit. The startup sound is your indicator (when you hear it for the second time) that you can let go of then four keys.

Very big problem with JSF about FORM and "id=" for HTML form's elements and

I have discovered a very big problem with JSF about FORM and "id=" for HTML form's elements and java instruction "request.getParameterNames()".
Suppose you have something like this, to render some datas form a Java Beans :
<h:dataTable value="#{TablesDb2Bean.myDataDb2ListSelection}" var="current" border="2" width="50%" cellpadding="2" cellspacing="2" style="text-align: center">
<h:column>
<f:facet name="header">
<h:outputText value="Name"/>
</f:facet>
<h:outputText id="nameTableDb2" value="#{current.db2_name_table}"/>
</h:column>
</h:dataTable>
Everything works fine...
Suppose you want to get the name/value pairs for id="nameTableDb2" and #{current.db2_name_table} to process them in a servlet. Here is the HTML generated :
<td><span <span class="attribute-name">id=<span class="attribute-value">"j_id_jsp_1715189495_22:0:nameTableDb2">my-table-db2-xxxxx</span></td>
You think you can use the java instructions :
Enumeration NamesParam = request.getParameterNames();
while (NomsParam.hasMoreElements()) {
String NameParam = (String) NamesParam.nextElement();
out.println("<h4>"++NameParam+ "+</h4>);
YOU ARE WRONG : request.getParameterNames() wants the syntax *name="nameTableDb2" but JSF must use id="nameTableDb2" for "<h:outputText"... So, you can't process datas in a FORM generated with JSF in a Servlet ! Perhaps I have made an error, but really, I wonder which ?
Edited by: ungars on Jul 18, 2010 12:43 AM
Edited by: ungars on Jul 18, 2010 12:45 AM

While I certainly appreciate ejb's helpful responses, this thread shows up a difference in perspective between how I read the forum and how others do. Author ejb is correct in advising you to stay inside JSF for form processing if form processing is what you want to do.
However, I detect another aspect to this post which reminds me of something Marc Andreesen once said when he was trying to get Netscape off the ground: "there's no such thing as bad HTML."
In this case, I interpret ungar's request as a new feature request. Can I phrase it like this?
"Wouldn't it be nice if I could render my nice form with JSF but, in certain cases, when I REALLY know what I'm doing" just post out to a separate servlet? I know that in this case I'll be missing out on all the nice validation, conversion, l10n, i18n, ajax, portlet and other features provided by JSF".
If this is the case, because it really misses the point of JSF, we don't allow it, but we do have an issue filed for it
https://javaserverfaces-spec-public.dev.java.net/issues/show_bug.cgi?id=127
If you can't wait for it to be fixed, you could decorate the FormRenderer to fix what you want.
I have an example in my JSF book that shows how to do this decoration. http://bit.ly/edburnsjsf2
Ed

I have a big problem with my Iphone 4...the pics and videos that i capture, often shows as inverted or orientted by 90/180/270 degrees. photos, one can rotate, but how about videos... is there any way i'm going wrong? this wasn't happening earlier

My question...
any answers pl.
I have a big problem with my Iphone 4...the pics and videos that i capture, often shows as inverted or orientted by 90/180/270 degrees. photos, one can rotate, but how about videos... is there any way i'm going wrong? this wasn't happening earlier

If I've understood you correctly then the ALLEXCEPT function may be what you're after and it could be applied in a similar way to the following...
=
RANKX(
ALL(Table1),
CALCULATE(
COUNTROWS(table1),
ALLEXCEPT(Table1, Table1[ContactReason])
DENSE
If this has missed the mark, would it be possible to clarify the requirement further?
Regards,
Michael Amadi
Please use the 'Mark as answer' link to mark a post that answers your question. If you find a reply helpful, please remember to vote it as helpful :)
Website: http://www.nimblelearn.com
Blog: http://www.nimblelearn.com/blog
Twitter: @nimblelearn

Big problem with a select using remote database

Similar Messages

Maybe you are looking for