Big problem with HAWK system "twin froz III"

Hi, i have this 3 cards, my problem is the temp with the system TWIN FROZ III
the temps in game with the nvidia 560 GTX TI HAWK is 87º with an ambient temp of 28º " playing 5 minutes )
with core clock and shadder clock default
underclocking to the twin froz II version ( 880 core clock ) the temps with 2 hours of play is of 81º with a ambient temp of 23º
Switching the mode of PERFORMANCE AND SILENT the temps are the same ( i restarted my pc to test )
and well...
with the GTX 560 AND GTX 560 TI TWIN FROZ II
the temps playing for 2 hours is of 65º MAX
so... i dont know what to do with the " TWIN FROZ III HAWK "
any idea? bios upgrade dont do nothing, drivers MSI dont do nothing, drivers NVIDIA dont do nothing..
so where is the problem? the thermal compound of the manofacturers? too much? to less? bad thermal?

This is just a guess, you would need to ask MSI for a confirmation, and I doubt they would confirm.
But.
I reckon that some batches of the MSI 560Ti HAWK just had poor heat sink connection.
When I took the heat sink off mine, the surface was extremely rough, with highly visible (and feel-able with your fingernail) grooves all over it. Possibly to compensate for that, it was slathered with too much thermal paste. Removing the factory-applied thermal paste and doing my own, thinner application of thermal paste dropped the temps by about 4-5 degrees.
I recently got some wet-n-dry sandpaper, and have been lapping the heatsink to remove the mechanical grooves. As I did this, I noticed that the lapping wasn't occurring evenly. This means that the surface of the heatsink, as well as having machining grooves, was not even particularly flat. Both of these things would reduce its performance.
It took me 3.5 hours of lapping with 80-grit wet n dry sandpaper to get the surface flat, and will take another hour or two to polish it up. (see pictures at start, and after 1 hour, to see how uneven the surface is). Will let you know if i see any further temp improvement after lapping.
Perhaps people who already get good temps with their MSI HAWK were lucky enough to get a very flat, well machined heat sink surface, without too much thermal paste.
http://i44.tinypic.com/vp86jm.jpg
http://i41.tinypic.com/35hnyfl.jpg

Similar Messages

I have big problems with mountain lion. you can not have a boot disk system I resulted in the need to re-download the os from scratch impiegandoci 8 hours, it is outrageous even with windows 95.

I have big problems with mountain lion. you can not have a boot disk system I resulted in the need to re-download the os from scratch impiegandoci 8 hours, it is outrageous even with windows 95.
at least that the operator has confirmed to me that he called me. I also have problems with either the start of the mac with the power off. I can not understand if it crashes or is just very very slow.
Finally, I have a problem with the external hard disck. I often said to have been ejected incorrectly (not true) and I start to restore the startup recovery disk because disk utility is ineffective from the normal operating system .. is a shocking thing, but how you reduced. in four years it had never happened. seem to have windows or worse. Wake up.
I am an Italian, alas, and then I would like an answer to my language because my € are the same as German French or English.

You are on Windows 2000, you do not have a "Firefox" button, and should consider yourself to be fortunate in that you still have menus and don't have to do anything to get the menus back instead of the "Firefox" button. (The same applies to Windows XP users).
Use the "File" menu to get to Import. You are not on Windows 7 or Vista, and don't have to put up with the nonsense added for Aero.
If you want the "Firefox" button you can get it with View -> toolbars -> (uncheck) Menu Bar. The menu bar and the "Firefox" button were supposed to be mutually exclusive (which is impossible in some cases without being incompatible).
Once you are using the "Firefox" button ...
Use the "Alt" key to view the menu bar (temporarily) containing File, Edit, View, History, Bookmarks, Tools, and Help. On Windows 7 and Vista, the menu bar was hidden by default in Firefox 4 and above. These menu items are more or less available under the "Firefox" button which has the most used of the built-in Firefox menu items available in a different format.
To get back to having menus again. "Firefox" button -> Options (second column) -> (check) Menu Bar
You can make '''Firefox 7.0.1''' look like Firefox 3.6.*, see numbered '''items 1-10''' in the following topic [http://dmcritchie.mvps.org/firefox/firefox-problems.htm#fx4interface Fix Firefox 4.0 toolbar user interface, problems (Make Firefox 4.0 thru 8.0, look like 3.6)]. ''Whether or not you make changes, you should be aware of what has changed and what you have to do to use changed or missing features.''
* http://dmcritchie.mvps.org/firefox/firefox-problems.htm#fx4interface

Workstation specs -- Any problems with this system quote?

Here are the specs I have been quoted. I'm not terribly knowledgeable about hardware, does anyone see any problems with this system? I have recently started shooting and editing weddings, engagements and corporate videos. I think it may be bit more than I need, but I would much prefer that to less than I need. Any input from the more tech savvy users would be much appreciated.
Darren Breckles
65539
ASUS Sabertooth X79 ATX LGA2011 DDR3 3PCI-E16 2PCI-E SATA3 USB3.0 SLI CrossFireX Audio Motherboard [Sabertooth X79]
72374
Mushkin Enhanced Blackline Frostbyte 32GB 4X8GB PC3-12800 DDR3-1600 CL10 Quad Channel Memory Kit [994055]
64540
Noctua NH-D14 SE2011 LGA2011 Heatpipe Cooler w/ NF-P14 140mm & NF-P12 120mm PWM Fans [NH-D14 SE2011] [Reg. $89.99]
67678
Intel 520 Series 240GB 2.5in SSD MLC 25nm SATA3 Solid State Disk Flash Drive OEM [SSDSC2CW240A310] [Reg. $279.99]
4729477
8 port internal via 2X SFF-8087, LSI2208 1GB cache, 6Gb/s, RAID 0/1/10/5/50/6/60 [RS25DB080]
1
84358
MSI GeForce GTX 770 OC Twin Frozr IV 1098/1150MHZ 2GB 7GHZ GDDR5 2xDVI HDMI DP PCI-E 3.0 Video Card [N770 TF 2GD5/OC] [Reg. $429.99]
62678
ASUS BW-12B1ST Blu-Ray Writer 12X BD-R 16X DVD+R SATA Black Retail [BW-12B1ST/BLK/G/AS][Reg. $89.98]
Environmental Fee $0.75 Per Item
45275
Microsoft Windows 7 Professional Edition 64Bit DVD SP1 OEM [FQC-04649] [Reg. $153.98]
75044
Fractal Design Define R4 ATX Tower Case Black Pearl 2X5.25 8X3.5INT No PSU Front 2XUSB3.0 Audio [FD-CA-DEF-R4-BL] [Reg. $119.99]
77641
Corsair AX860 860W ATX 12V V2.31 80 Plus Platinum Modular Power Supply Active PFC 120mm Fa *IR-$10* [CP-9020044-NA] [Reg. $189.89]
49665
nMedia ZE-C118 3.5in Multi Function Panel Flash Card Reader W/USB2.0 eSATA SDHC2.0 Win 7 Black [ZE-C118 ] [Reg. $19.99]
58276
StarTech.com 3.5in Hard Drive to 5.25in Front Bay Bracket Adapter [BRACKETFDBK]
78186
Noctua NF-A14 FLX 140mm Ultra Quiet Cooling Fan 900-1200RPM 115.5M3/H 19.2DBA 3-PIN [NF-A14 FLX] [Reg. $22.99]
4
22823
Premium PC Assembly and Testing With 1 Year Limited NCIX Warranty (PRE-CONFIG WIN. OS If Purchased)
Environmental Fee $3.00 Per Item
Note: Includes extra attention to cabling, lighting installation and extra burn-in period. Recommended for windowed cases. Assembly requires an additional 4-5* business days to ship once all parts are in stock. *typical lead time (currently 2-5 business days)
1
$3.00
73920-1
NCIX 3 Year On-Site Care Coverage for PC $3000.00 - $3999.99 (22823)
89510
Intel Core i7 4930K 6 Core 3.4GHZ (3.9GHZ Turbo) 12MB Hyperthreading LGA2011 Processor No HSF [BX80633i74930K] [Reg. $649.99]
81958
Western Digital RE 2TB SATA3 7200RPM 64MB Cache 3.5in Internal Hard Drive [WD2000FYYZ] [Reg. $213.57]
Environmental Fee $0.75 Per Item
4

Very nice build list Darren!
I would have selected the Samsung 840 Pro 256GB SSD over the Intel 520, and Areca's ARC-1882i over the Intel SAS controller you list, but those are preferences not essential changes.
Regards,
Jim

Helloo! I have super big problem with my Air.

Helloo! I have super big problem with my Air,10.8.5 ,it asks every 10 sec to make some changes and asks me for password all the time!! I cant acces my documesnt,pics,music,NOTHING at all! Finder is not working,i cant open any folder,icons are missing also,i cant open any of them,mozzila,chrome..im really going crazy.. i updated tonight my phone on new IOS 7 through my comp,cant be that i messed up everything because of that..this comp.is like 10 days old.
btw. i created new user,and everything is working ok.

Back up all data. Don't continue unless you're sure you can restore from a backup, even if you're unable to log in.
This procedure will unlock all your user files (not system files) and reset their ownership and access-control lists to the default. If you've set special values for those attributes on any of your files, they will be reverted. In that case, either stop here, or be prepared to recreate the settings if necessary. Do so only after verifying that those settings didn't cause the problem. If none of this is meaningful to you, you don't need to worry about it.
Step 1
If you have more than one user account, and the one in question is not an administrator account, then temporarily promote it to administrator status in the Users & Groups preference pane. To do that, unlock the preference pane using the credentials of an administrator, check the box marked Allow user to administer this computer, then reboot. You can demote the problem account back to standard status when this step has been completed.
Triple-click the following line on this page to select it. Copy the selected text to the Clipboard (command-C):
{ sudo chflags -R nouchg,nouappnd ~ $TMPDIR.. ; sudo chown -R $UID:staff ~ $_ ; sudo chmod -R u+rwX ~ $_ ; chmod -R -N ~ $_ ; } 2> /dev/null
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). You'll be prompted for your login password. Nothing will be displayed when you type it. You may get a one-time warning to be careful. If you don’t have a login password, you’ll need to set one before you can run the command. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The command will take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear, then quit Terminal.
Step 2 (optional)
Take this step only if you have trouble with Step 1 or if it doesn't solve the problem.
Boot into Recovery. When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar. A Terminal window will open.
In the Terminal window, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window will open. You’re not going to reset a password.
Select your boot volume ("Macintosh HD," unless you gave it a different name) if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Under Reset Home Directory Permissions and ACLs, click the Reset button.
Select
 ▹ Restart
from the menu bar.

Big Problem with new PB SD-DL (shuts down each time)

Hello I have a big Problem with my new PB 1,67 SD-DL.
If I use it with the Powersupply there is no problem but if want to use it without the powersupply it shut down each time!!!
Sometimes after 5 minutes, sometimes after 3 minutes or 10 minutes... (remaining battery time 3 hours)
If I reboot it tells me that the system clock is before 2001 and I have set the right date.
What should I do? I have already made a PMU Reset but nothing happens.
The PB is 3 Weeks old and I have calibrate the battery correctly.

You state that you've already tried resetting your PMU. Perhaps you should try resetting your NVRAM & PRAM. Frankly, I think this is a long shot, but it's worth a try.

Hi I've a big problem with adobe acrobat reader XI pro and I hope you can help me. The problem is; when I past copied text from some pdf books (not all of them) it past symbols only! wherever I past it! and even if I coped that text from another pdf reade

Hi
I've a big problem with adobe acrobat reader XI pro and I hope you can help me.
The problem is; when I past copied text from some pdf books (not all of them) it past symbols only! wherever I past it! and even if I coped that text from another pdf reader (adobe pdf reader, internet browsers, ...etc.).
This problem started to happen since yesterday when I installed adobe acrobat reader XI pro to try it before I buy it, and before that when I was using the free adobe pdf reader I was totally able to copy any text from any pdf and past it anywhere with nothing wrong.
What can I do?
thank you a lot.

There is no product called Adobe Acrobat Reader Pro. There is
- Adobe Acrobat Pro ($$)
- Adobe Reader (free)
Which do you have? And are you a programmer?

Having big problems with my new Mac Pro, when I launch Photoshop CC, I get an error message, can carry on but after a few tasks it starts going gar... menus go blank, when you try to save it shows a blank box.... can anybody help?

Having big problems with my new Mac Pro, when I launch Photoshop CC, I get an error message, can carry on but after a few tasks it starts going gar... menus go blank, when you try to save it shows a blank box.... can anybody help?

when I launch Photoshop CC, I get an error message
and what exactly is the text of that error message?

My iphone 4s crashes too much when i download and app from store and open it its freeze or crash and restart the phone i think i am having big problem with this device i restored it to factory settings and no waay!

My iphone 4s crashes too much when i download and app from store and open it its freeze or crash and restart the phone i think i am having big problem with this device i restored it to factory settings and no waay!

I think many of us need a Defense Against the Podcasts App professor.
Have you looked at this Apple support page?
http://support.apple.com/kb/HT6190?viewlocale=en_US&locale=en_US

I am no longer being asked for a password when downloading an app, big problem with kids

I am no longer being asked for a password when downloading an app or music in iTunes, big problem with kids. How do I enable

To elaborate further, in those restrictions you can specify exactly what types of actions you would like to restrict.
I think you'll find this accomplishes your objective.

Weird Problems with K9A2 System

Can Someone Help Me?
I recently built a new system and have had nothing but problems. See system config in signature (Left off OCZ PRO Xtreme 1000W Power Supply With 4 12 Vrails at a max of 26 Amps each or 82 Amp all together and a 5 Volt rail at 30 Amps Max.) After putting it all (except the seagate 250 IDE drive), system would not even enter post. After strippin memory down to just 2 GB system finally entered post (although my memory were the same models from G.Skill one set was older and one set was new they had different voltages old required 1.9-2.0 while the newer worked at the default 1.8 voltage all timing and specs besides voltage were the same). I entered the bios setup and set my Memory voltage to 1.95 (What I had been runnin the older memory in my old system). Inserted all the memory back in and system booted right up to allow me to install my OS (Vista Home Premium 64-bit).
After the OS installed the system started having all kinds of wierd clitches/problems at one point it locked up and neither reset button nor the power button would work. After unplugging the power I noticed that the M connector for the front case switches was a little loose. I decided to just plug wires directly into board instead of using th M connector. Now my buttons worked again. I then proceded back into the bios and checked my voltages in the hardware monitor of the bios. All voltages looked to be fine with only an ocassional voltage fluctuation in the 5V line from 4.97 to 4.92 Volts and the 12V line was a little high 12.4 Volts. However, after booting back into vista and installing Everest Ultimate Edition it detected the that the 5 Volt line was only at 4.67 Volts. But was not fluctuating at all.
After installing the drivers for my system and proceding to install my anti-virus software the system started freaking out the mouse started lagging and sometimes not responding at all and the keyboard worked intermittently. I decided to remove the M connectors from these as well and that solved that problem. Upon rebooting the system and trying to install the Anti-Virus software again the system started telling me that I had just plugged in something to the audio connector. I had not so I just ignored it and continued to install my anti-virus. (the audio connector alert popped up 4X while I was finishing the installation of the software. I decided to test the audo so I but a DVD in and and watched the whole movie sound worked fine and no more pop ups about the audio connector until I started to install more software. During the next install of software the screen went black and the DVD and Hard Drive LED stopped flashing. It stayed this way for about 10 Min. I decided to hit the reset button and the system would not enter post again.
Once again I started to pull the Memeory It finnally worked after removing the new memory that I had just bought but none of my Maxtor hard drives were recognized and I started smelling smoke. ( Strange only the Maxtor drives went out, all had the interface boards and one chip on each drive fried. After disconnecting these drives and replacing the maxtor 120 GB IDE drive that had fried with a Seagate 250 GB IDE drive and reinstalling everyting onto it since the maxtor was my boot drive the system started up and was running fine except for the occasioal audio connector popup I finished Installing the rest of my software and everything was running good. So I assumed the problems were due to faulty ram. I contacted NewEgg and arranges for an RMA on the memory went shipped the memory back to NewEgg came back and started to move file some file to my NAS200 After about 4 hours the system locked up again (It had been almost 36 hours since I had had anyother problems with the system and it had not been turned off the whole time. All temps were good CPU was at 29C and GPU was at 46C system temp was 31C according to my Everest Ultimate so I didn't think it was a heat related issue)
Upon restarting my computer I got a message that a recent overclocking attempt had failed (I did not try to overclock!!) After going back into Bios and resetting all my settings the computer would not post agian. I tried to clear the CMOS with the jumper just to make sure that there wasn't any coruption inthe CMOS. Still no Luck. Pulled out one stick of the older ram and it booted but very slow. I went to a local parts dealer and bought some extremely over prived memory just so I could get my system back to 2 GB because I had video edditing software that didn't work very good on 1 GB. After installing no post again. So I started testing each stick of memory that I had in DIMM 1 they all worked but anytime I insert one into DIMM 2 it would not boot. Finnally I but 2 sticks into DIMM 3&4 and It started up and ran good. I decided to set my bios Unganged option to enabled and put memory back into DIMM 1 No luck would not post. I removed the memory from DIMM 1 and computer has worked ever fine except for an error coming out from sleep mode. (Never had a computer that didn't have a problem with that) I even updated the BIOS to 1.5 which was suppose to fix the wakeup problem.
So here is what I have I can use Dimm 1 by itself or I can use DIMM 3&4 but not both together. I'm about to buy a Power Supply (single 12V rail at 40 Amps and a 5V rail at 50 Amps) because I think that the 12 V reading as 12.4 and the 5 Volts reading as 4.67 in Everest Ultimate and 4.97 volts in Bios might have something to do with some of my problems. I did not check the Memory that I RMA'd by them selves on DIMM 3&4. I think that they may have been good now.
Can the 5V line registering the way it is 4.97 Bios/4.67 in Windows cause DIMM 2 to not function and create the lockups or can the socket or board be bad and that be what is causing this problem? And Should I RMA the motherboard back or just purchase a different motherboard?
System is pretty Stable as it is now with the voltages as they are. I really wantt to be able to put my new memory that I get back from NewEgg in and have my 4 GB of memory.

OK I have removed the mother board and and checked for grounding issue or any damage from the fried hard drives board looks good did not find any grounding issues in the case. One thing I did not check was that I was using a Startech SATA to IDE converter to connect the the IDE drives that I didn't have the connectors on the board or.
I did some research before buying them and made sure to get one with a plastic box around the pcb due to so many people compaining that their's would short to the hard drive case. Since the loss of the HDD I didn't need the adapter so I quit Using it.
when I did my research on the adapter I found that many people had said that their HDD got hoter when using the adapter I guess my HDD just couldn't handle it. The Drive that I had connected with it was about 6 years old and I had been having intermittent problems with the connector not making a good connection when it was in my old system. (Anytime I would shut the power off for a long period of time and the HDD had a chance to cool down I would have to unplug and reconnect the ide cable from that drive.)
I didn't think that the problem would continue as I was moving it to an new case, motherboard, and cable.
And it just so happened that the drives that fried were all connected the the sata controller in the SB600 chip. My two SATA drives that survied the fire were on the Promise T3 controller. So I guess it is possible that the adapter/HDD configuration I had with the SATA to IDE caused some sort of feedback into the Motherboard's SATA controller and back into the oter HDD on that Controller. I have checked all SATA ports since this happened and they all still work so I'm assuming that it did not damage the chip.
As far as the memory situattion I don't see how the HDD frying could have damaged the Memory unless there is some special connectin between DIMM2 and the SATA controller that doesn't exist with the other DIMM slots. and if it had somehow effected the memory controller to cause this problem I would assume it would have done alot more damage to the cpu than just the memory controller part. So I think I'll try to RMA a new motherboard, if ZippZoomFly will let me this long after getting the board I've had it for about 3.5 weeks waiting on the other parts for the new system) and see what happens.
As for the memory, itself they are not mixed brands or models. I bought one set about a year ago when I purchased my X2 6000 processor and they have worked great as long as I kept the voltage above 1.9 V. The new memory has the same model # as the old but the label on them states the same timings and only a different voltage range. So as long as they voltage was set to within the range of both sets they should work exactly the same. I did notice that the board would only detect 3.25 GB instead of 4 GB, and I was prepared for this. Every Motherboard I have ever owned, no matter who the Manufacturer was, has had this problem. However Vista reported the memory correctly.
I guess if the new motherboard exhibits the same memory problem with not letting me use all slots then i'll buy a 2X2GB set

Remote Resources: "A problem with the system proxy caused the connection to fail: End of file"

Hi, I am trying to use "Remote Resources" on the current version of the Microsoft Remote Desktop for Android app, I can input the webfeed and it even shows the apps that I have configured on the server for "Remote App", sadly whenever
I try to load any of the RemoteApps, I receive an error stating " A problem with the system proxy caused the connection to fail. End of File".
I don't know what I can do to fix this, I've tried many things to no avail, also, normal Remote Desktop connections from the Microsoft Android app work flawlessly to the server.
The relevant log is the following:
[2014-Jan-09 04:40:54] RDP (0): ----- BEGIN ACTIVE CONNECTION -----
[2014-Jan-09 04:40:54] RDP (0): Final rdp configuration used: memory bookmark [
label
hostname DIAZSERVER
port 3389
loadbalanceinfo
ui.swapmousebutton false
remote.program ||ZWaveUtil
remote.workingdirectory
remote.name ZWave Adapter Utility
remote.args
rail true
soundmode 0
connect_to_console false
redirectsdcard true
performance_flags 134
arc.sessionid 0
anonymous_username
authentication_level 2
use_redirection_server_name false
username administrator
gateway [
host = DIAZSERVER
port = 443
bypass = false
connect info[
hostnames = [localhost]
gatewayHost = DIAZSERVER
gatewayPort = 443
routingToken = Cookie: mstshash=administrator
redirectionGUID =
proxyHost = 200.5.68.10
proxyPort = 8080
sessionId = -1
[2014-Jan-09 04:40:54] RDP (0): Using HttpConnect proxy at 200.5.68.10:8080
[2014-Jan-09 04:40:54] RDP (0): Using Basic Authentication with username ''
[2014-Jan-09 04:40:54] RDP (0): Protocol state changed to: ProtocolConnectingNetwork(1)
AsioEndpointContext (0): startup(): starting up down context
[2014-Jan-09 04:40:54] RDP (0): Resolved '200.5.68.10' to '200.5.68.10' using NameResolveMethod_DNS(1)
[2014-Jan-09 04:40:54] RDP (0): Resolved '200.5.68.10' to '200.5.68.10' using NameResolveMethod_DNS(1)
ASIOSocketAdapter (9): readSomething error. message: End of file. instance: 0x5d39d5c0
RpcOverHttp (9): Stream error in endpoint 0x5abbc170 : A problem with the system proxy caused the connection to fail: End of file
[2014-Jan-09 04:40:55] RDP (0): Error message: A problem with the system proxy caused the connection to fail: End of file
[2014-Jan-09 04:40:55] RDP (0): Error message: A problem with the system proxy caused the connection to fail: End of file
[2014-Jan-09 04:40:55] RDP (0): Protocol state changed to: ProtocolDisconnected(8)
ASIOSocketAdapter (9): handleRead(): exception: Exception in file '/var/lib/jenkins/jobs/rc-android-app/workspace/rdp-layer/library/jni/librdp/private/httpendpoint.cpp' at line 489
    User Message : Failed to read from channel: -1. instance: 0x5d39d5c0
[2014-Jan-09 04:40:55] RDP (0): Disconnect initiated by client
RpcOverHttp (9): Exception in endpoint 0x5abbc170 : Exception in file '/var/lib/jenkins/jobs/rc-android-app/workspace/rdp-layer/library/jni/librdp/private/httpendpoint.cpp' at line 489
    User Message : A problem with the system proxy caused the connection to fail: Failed to read from channel: -1
[2014-Jan-09 04:40:55] RDP (0): Exception caught: Exception in file '/var/lib/jenkins/jobs/rc-android-app/workspace/rdp-layer/library/jni/librdp/private/httpendpoint.cpp' at line 489
    User Message : A problem with the system proxy caused the connection to fail: Failed to read from channel: -1
[2014-Jan-09 04:40:55] RDP (0): Exception caught: Exception in file '/var/lib/jenkins/jobs/rc-android-app/workspace/rdp-layer/library/jni/librdp/private/httpendpoint.cpp' at line 489
    User Message : A problem with the system proxy caused the connection to fail: Failed to read from channel: -1
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
[2014-Jan-09 04:40:57] RDP (0): ------ END ACTIVE CONNECTION ------

My problem is that the "proxy" is the proxy set up by my 3G configuration so, I tried connecting to the remote resources through my work wifi and I get the following:
[2014-Jan-14 16:58:13] RDP (0): ----- BEGIN ACTIVE CONNECTION -----
[2014-Jan-14 16:58:13] RDP (0): Final rdp configuration used: memory bookmark [
label
hostname DIAZSERVER
port 3389
loadbalanceinfo
ui.swapmousebutton false
remote.program ||chrome
remote.workingdirectory
remote.name Google Chrome
remote.args
rail true
soundmode 0
connect_to_console false
redirectsdcard true
performance_flags 134
arc.sessionid 0
anonymous_username
authentication_level 2
use_redirection_server_name false
username Administrator
gateway [
host = DIAZSERVER
port = 443
bypass = false
connect info[
hostnames = [localhost]
gatewayHost = DIAZSERVER
gatewayPort = 443
routingToken = Cookie: mstshash=Administrator
redirectionGUID =
proxyHost =
proxyPort = 0
sessionId = -1
[2014-Jan-14 16:58:13] RDP (0): Not using any proxy
[2014-Jan-14 16:58:13] RDP (0): Protocol state changed to: ProtocolConnectingNetwork(1)
AsioEndpointContext (0): startup(): starting up down context
ASIOSocketAdapter (9): handleResolve(): boost error: Host not found. Please provide the fully-qualified name or the IP address of the host.. instance: 0x5d474090
RpcOverHttp (9): Stream error in endpoint 0x5d46b678 : Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 16:58:17] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 16:58:17] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 16:58:17] RDP (0): Protocol state changed to: ProtocolDisconnected(8)
ASIOSocketAdapter (9): handleResolve(): boost error: Host not found. Please provide the fully-qualified name or the IP address of the host.. instance: 0x5d445158
RpcOverHttp (9): Stream error in endpoint 0x5d49fa30 : Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 16:58:17] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 16:58:17] RDP (0): Disconnect initiated by client
[2014-Jan-14 16:58:17] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
[2014-Jan-14 16:58:17] RDP (0): ------ END ACTIVE CONNECTION ------
Now, I know the host can be resolved because: if I connect to the same host but on a full remote desktop (as opposed to just RemoteApp on it) I have no trouble either through 3G OR through my work connection.
Moreover, I also tried directly inputting the IP as opposed to the web address of my server, I get the same error, that is the Remote Resources tab is able to access the feed (because it shows the available RemoteApps) but when I click an app it says it can't
find the Host, here's the log for the connection directly to the IP address/rdweb/feed/webfeed.aspx :
[2014-Jan-14 17:09:27] RDP (0): ----- BEGIN ACTIVE CONNECTION -----
[2014-Jan-14 17:09:27] RDP (0): Final rdp configuration used: memory bookmark [
label
hostname DIAZSERVER
port 3389
loadbalanceinfo
ui.swapmousebutton false
remote.program ||chrome
remote.workingdirectory
remote.name Google Chrome
remote.args
rail true
soundmode 0
connect_to_console false
redirectsdcard true
performance_flags 134
arc.sessionid 0
anonymous_username
authentication_level 2
use_redirection_server_name false
username administrator
gateway [
host = DIAZSERVER
port = 443
bypass = false
connect info[
hostnames = [localhost]
gatewayHost = DIAZSERVER
gatewayPort = 443
routingToken = Cookie: mstshash=administrator
redirectionGUID =
proxyHost =
proxyPort = 0
sessionId = -1
[2014-Jan-14 17:09:27] RDP (0): Not using any proxy
[2014-Jan-14 17:09:27] RDP (0): Protocol state changed to: ProtocolConnectingNetwork(1)
AsioEndpointContext (0): startup(): starting up down context
ASIOSocketAdapter (9): handleResolve(): boost error: Host not found. Please provide the fully-qualified name or the IP address of the host.. instance: 0x5d372f28
RpcOverHttp (9): Stream error in endpoint 0x5dd6b168 : Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 17:09:31] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 17:09:31] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 17:09:31] RDP (0): Protocol state changed to: ProtocolDisconnected(8)
ASIOSocketAdapter (9): handleResolve(): boost error: Host not found. Please provide the fully-qualified name or the IP address of the host.. instance: 0x5d378de0
RpcOverHttp (9): Stream error in endpoint 0x5e9cc1f0 : Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 17:09:31] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
[2014-Jan-14 17:09:31] RDP (0): Disconnect initiated by client
[2014-Jan-14 17:09:31] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
AsioEndpointContext (0): shutdown(): shutting down context
AsioEndpointContext (0): shutdown(): context shut down
[2014-Jan-14 17:09:31] RDP (0): ------ END ACTIVE CONNECTION ------
I'm really puzzled here, I've tried checking if ports where open, and ports 443 and 3389 are wide open, I don't know what else it could be.

Big problems with slideshows

Hi, I've a big problem with iPhoto (and Aperture too, but I'll say later).
Two days ago I was creating a small slideshow (18 pictures) and everything was fine. Suddenly, while I was looking for a theme, switching between 3 of them, iPhoto stopped to work. No ESC, no key, I had to restart my iMac, turning it off.
From this moment every slideshow I select, iPhoto stop to work and need a force quit. So I restored a library, from Time machine, but nothing changed.
So I bought Aperture, but nothing changed, using iPhoto Library.
Now I've created an Aperture Library, importing in it my old iPhoto Library. Is there any way to "clean" iPhoto, reinstalling it from new? Do I need such a action?
Thank you and best regards.

That means that there is something in your account that's the culprit. First try the following:
1 - delete the iPhoto preference file, com.apple.iPhoto.plist, that resides in your
User/Home/Library/ Preferences folder.
2 - delete iPhoto's cache file, Cache.db, that is located in your
User/Home/Library/Caches/com.apple.iPhoto folder (Snow Leopard and Earlier).
or with Lion and Mt. Lion from the User/Library/Containers/com.apple.iPhoto/
Data/Library/Caches/com.apple.iPhoto folder
3 - launch iPhoto and try again.
NOTE 1: If you're moved your library from its default location in your Home/Pictures folder you will have to point iPhoto to its new location when you next open iPhoto by holding down the Option key when launching iPhoto. You'll also have to reset the iPhoto's various preferences.
NOTE 2: In Lion and Mountain Lion the Library folder is now invisible. To make it permanently visible enter the following in the Terminal application window: chflags nohidden ~/Library and hit the Enter button - 10.7: Un-hide the User Library folder.
If that fails it might be another preference file that's causing the problem. Here's how to test for that:
Trouble Shooting Preferences
NOTE: In Lion and Mountain Lion the Library folder is now invisible. To make it permanently visible enter the following in the Terminal application window: chflags nohidden ~/Library and hit the Enter button - 10.7: Un-hide the User Library folder.
1 - close all applications.
2 - open your Home/Library folder and Option-drag (copy) the Preferences folder to the Desktop.
3 - select the contents of your Home/Library/Preferences folder and drag them into the Trash bin in the Dock. You will be asked to provide your Admin password.
4 - reboot.
5 - run the application again and determine if the problems is fixed
6 - If the problem is fixed:
A - open the working Home/Library/Preferences folder.
B - Open the Preferences folder on the Desktop, select all of the contents and drag them into the working Home/Library/Preferences folder.
C - When the Copy window pops up check the "Apply to All" check box and then click on the Don't Replace or Skip button.
D - reboot.
7 - If the problem is NOT fixed, drag the contents of the Preference folder on the Desktop into the Home/Library/Preference folder and replace the entire contents that were created by clicking on Replace.
8 - reboot.
OT

Having big problems with Creative Zen Micro Photo!! I need much urgent help!

Hi. I am having a big problem with my MP3 Creative Zen Micro Photo device at the computer.Here is the thing:Before I bought this I had the regular Zen Micro & having fun with it. I had no problems with that when I used the Media Explorer to transfer songs. So I bought the Zen Micro Photo & installed it my computer. As normal I used the Media Explorer to transfer songs & pictures.So I reinstalled Windows XP at my computer, and when I installed the CD that followed to transfer new songs, the Windows said that it's an unknown thing I have connected in the USB.So I installed Service Pack & 2. I have tried to install drivers from the cd but it seems that there are no drivers on the cd! The big problem is that when I connect the MP3 to the computer, it doesn't read it's a Zen Micro, it's just unknown! So the Zen Micro Photo Media Explorer program doesn't work & I can't transfer songs or picture on it! And it just happened after I re-installed Windows on my computer. The same thing happened on my brother's computer after he re-installed windows. And when I connect the MP3 to the USB, it says that it's not a USB 2.0, but .! And I am sure it is 2.0 because it has always been like that before I re-installed windows. Also the MP3 does not re-charge when I put it my computer! The battery is just the same, it tries to do it but it doesn't. So I am using my sisters computer to charge the MP3 & transfer songs. I have tried everything but I can't seem to understand what the problem is? I have never experienced something like this before, and I really hope you can help me with this! To be honest I think what I am missing is the driver. So can someone PLEASE provide me the link for the driver? I have downloaded all those 3 on www.creative.com, but they are none of them! Also that playforsure firmawre thingy does not work because it sais that I have to connect my MP3, and it is connected already!Please reply as quick as possible! Thanks a lot for you kind help!
I have also sent this mail to creative support! But please help me I have had this problem for almost 2 months now! =(Message Edited by anakwalajinn on 05-0-2006 08:47 PM

Might try this:? http://forums.creative.com/creativel...mp=true#M95059

8900 printer changed black cart. error code problem with printer system

Changed black cartridge in 8900 series all in one printer error message says trouble with print system call HP. Have removed and reinstalled catridge still same error message. HELP!!!!!

Hi @melvinc
Welcome to the forums
I read about the issue you are facing on your printer, as it's now showing a problem with the ink system. I cannot locate a "8900" printer, could you possibly have the Officejet 8600? If so, please try out the steps from the guide below. If you reach a step where it asks to replace the printhead or printer, call us directly to see what your replacement options are with HP.
A 'Problem with Ink System' Error Message Displays on the Control Panel or Computer During Setup
Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
Have a great day
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Big problem with Airport Extreme and Vivax Provider in Brazil

Hello guys.
I live in Brazil and I bought my Airport Extreme in a recent trip to USA.
For some years I was a client of Telefonica and had an ADSL link, I had a D'Link G604T to do both the modem and router operation in the same box. I was happy with my connection of 1Mbps.
In a recent promotion of Vivax I switched to a cable connection to have both TV and Internet at the same operator, my link now has 3Mbps.
With this pack I also received free one RCA cable modem model DCM425B, it was installed fine in one computer only. Everything was fine my connection was faster the old one.
So I went to install the Airport Extreme to make things even better.
After I installed I went to see the web status of my modem, all parts were looking fine, but the modem could not see the computer. Bad sign.
I talked to Vivax support people and apparently it was a problem with their network setup and they manage to make it right. My model now sees my computer.
After that problem was solved I could not make AE to work with the modem, it had the green light and the setup looked fine, but I could not open any site. I tried to turn off my modem and AE, waited some minutes and turned on first my modem and after it was up I turned on AE. All lights looked fine but again no connection to any site.
I called again the Vivax support center and they tried to help me but the don't know AE and they could not help me with all the details but said there was 2 10.x.x.x coming from my side. So I tried to use in bridge mode. I also selected the 192.x.x.x range instead of 10.x.x.x as default.
After many setups and turn off and on again my connection is working but I have a big problem with wireless. If I turn it on I loose my connection, it seems that AE sends 2 equal ethernet address to Vivax and their network don't like it cutting me off.
So my connection setup is like this:
RCA Cable modem model DCM425B at 3Mbps using a 200.x.x.x ip
Airport Extreme connected to a Mac and a Windows PC by wire using the 192.x.x.x range ip
Wireless is off
Bridge mode is on
This the only way I could make it work.

After a firmware update it worked fine.

Big problem with HAWK system "twin froz III"

Similar Messages

Maybe you are looking for