Big problems help plz

Since upgrading to a MSI K8N Neo Platinum nForce3 250 (Socket 754) and a A64 3000..the rest of my system is in sig
i didnt think it was running that fast..and when i did a benchmark with 3d mark 01 it showed up with 17700...and that was with the gfx card overclcoked
i tried messing about with memory timings and overclocking the rig a bit but was still far from impressed....anyway
i bought a new heatsink/fan and a raptor grive to use for my O/S after i had put it all together and switched on the comp it just didnt boot ....all i got was one longish beep the a pause followed by another and so on .
i tried reseating the cpu and heatsink tried the memory in different slots checked gfx card etc still nothing...
anyway i went back to my n/force 2 and barton 2500@3200 with the same memory and gfx card i used on the A64 and it works fine....i benchmarked it with 3d mark 01 and got a score of about 16700...without the gfx card overclocked.....
so have i got a borked mobo or borked chip the new system should be a lot faster than a barton 2500..can anyone tell me what the beep means off this mobo....
cheers in advance for any replies Bram

You can find BIOS beep codes at: http://bioscentral.com/beepcodes/awardbeep.htm
It's not clear to me whether any of those apply to you...are you having a repeating long beep or is it long then short?
Does your CPU fan appear to be running at its full speed? Did you make sure to clean off the old thermal compound fully? Is the new thermal compound applied properly? (don't use too much!)
Have you tried clearing the CMOS? Unplug, and remove the battery for a minute or two. Try also to startup with nothing connected but the CPU, graphics card, and 1 stick of RAM. Before anyone else says it, as it seems to be the answer to end all answers for any problems in this forum, what is your power supply rated at? Not just watts but each rail...for example my PSU: 3.3v 30A 5v 38a 12V1 18A 12v2 15A
Finally, you're not going to see much of an increase in 3dMark tests just because you're on a faster CPU. It's almost completely based off your graphics card. I have a 9800PRO that tests at about 2% faster going from 200mhz to 220mhz for example on my A64 3200+.
Just some general ideas to try based on my recent experiences...in the last month or so I've built 3 PCs, 2 for relatives and 1 for myself. I think about every problem you can have I encountered but it was a great learning experience and a lot of fun!

Similar Messages

Lenovo B590 big problem, HELP!!!

Hello,
I have big problem with my Lenovo B590 20206 laptop. [windows 7 pro 64 bit installed]
After turn my laptop to standby mode (manualy or after 1 hour without use laptop) and when I want to wake up laptop all what I see is black screen and I must hold push power button for 5 second to force off.
BTW when laptop is in standby mode everything looks good, led is blinking and after pushing any button I hear that fan and hard disk is starting but all what i got is black screen, even CTRL + ALT + DEL doesnt work.
I've tried replace RAM, reinstalled alot of drivers but without success. Windows 7 of course works perfect, only sleep mode (standby] doesnt work.
Another problem is that i cant update bios, my current is 1.10 which is not recent imho (maybe bios update would help with problem above?). Ive downloaded BIOS Update Utility for Windows 7 from lenovo site but when i tried to update i ve got a warning like this:
so i tried to update from Windows 7 and BIOS Update Utility for CD ISO image and i got error "THE SYSTEM PROGRAM FILE IS DAMAGED. THE PROCESS HAS BEEN CANCELED."
My last question is about disk replacement in that lenovo b590, original 500gb disk is 7mm high, can I replace it with 9,5mm disk?
Any help would be appreciated, sorry for my english btw.

hi feeling,
Welcome to Lenovo Community Forums!
About the sleep Issue
Can you try the solution on this article
http://forums.lenovo.com/t5/IdeaPad-Y-U-V-Z-and-P-series/u310-touch-Wakes-from-sleep-then-goes-back-...
About the BIOs Update can you check and share what it says under your Bios with regards to the version installed
Let me know your findings
Cheers!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

My big problem Help me plz?

Hi,
My question is,
How to make a jar file or an executable file for swing programs,
please help me.
Thanks a lot.
Mr.John...

You just use the jar tool that comes with your sdk and to make it self-running u simply place i line like:
Main-Class: yourclassname
but don't add a .class extension to your main class name
also, for more information on using the jar tool go to:
http://java.sun.com/j2se/1.4.2/docs/tooldocs/solaris/jar.html
if your using solaris or linux
or
http://java.sun.com/j2se/1.4.2/docs/tooldocs/windows/jar.html
if your using windows

Table Control Text fields problem , help plz

Hello Anand , Rich , John & All
I hav problem with Text 3 fields( type c)(either L or R aligned ) , it is not geting updated , otherwise everything else is perfectly fine(scrolling,sorting etc ....) .
Fields giving problem are
1. Status(20) type c
2. Fdat type date
3. Remark(100) type c
All numerical fields are working fine .
 My yahoo messenger-id is [email protected]
Any light on this will be awarded plz .
FLOW LOGIC
PROCESS BEFORE OUTPUT.
MODULE SET_STATUS.
LOOP AT ITAB
 WITH CONTROL TCL1
 CURSOR TCL1-CURRENT_LINE .
 MODULE SET_LINE_COUNT .
ENDLOOP.
PROCESS AFTER INPUT.
MODULE UPD_OK_COD.
MODULE EXIT_COMAND AT EXIT-COMMAND.
MODULE SCROLL_SORT.
LOOP AT ITAB.
 MODULE UPDATE_ITAB.
ENDLOOP.
MODULE UPDATE_TABLE.
REPORT ZSD_REP_ORDER_BANK_CHANGE NO STANDARD PAGE HEADING LINE-SIZE 255.
TABLES: VBAK,VBAP,VBRK,ZSD_TABL_ORDBANK,MARA,KONV.
CONTROLS: TCL1 TYPE TABLEVIEW USING SCREEN 0200.
DATA: ITAB LIKE ZSD_TABL_ORDBANK OCCURS 0 WITH HEADER LINE,
 WA_ITAB LIKE ZSD_TABL_ORDBANK,
 OK_CODE LIKE SY-UCOMM,
 SAVE_OK_CODE LIKE SY-UCOMM,
 UPD_OK_CODE LIKE SY-UCOMM,
 ANSWER TYPE C,
 I LIKE SY-LOOPC ,
 J LIKE SY-LOOPC,
 V_LINES LIKE SY-LOOPC,
 LINE_COUNT LIKE SY-LOOPC,
 STS TYPE N,
 EMGRP LIKE MARA-EXTWG,
 QTY LIKE ZSD_TABL_ORDBANK-QTY,
 UPRICE LIKE ZSD_TABL_ORDBANK-UPRICE,
 TOT LIKE ZSD_TABL_ORDBANK-TOT,
 INO LIKE VBAP-POSNR,
 COL TYPE CXTAB_COLUMN,
 COPIED_ONCE ,
 FLDNAME(100),HELP(100).
FIELD-SYMBOLS:
 <FS_ITAB> LIKE LINE OF ITAB,
 <FS_TCL1> LIKE LINE OF TCL1-COLS.
SELECTION-SCREEN BEGIN OF BLOCK b1 WITH FRAME TITLE text-000.
SELECT-OPTIONS: S_CCODE FOR ZSD_TABL_ORDBANK-CCODE
 NO INTERVALS NO-EXTENSION OBLIGATORY,
 S_SORG FOR ZSD_TABL_ORDBANK-SORG
 NO INTERVALS NO-EXTENSION OBLIGATORY,
 S_DCHAN FOR ZSD_TABL_ORDBANK-DISTCHAN,
 S_DIV FOR ZSD_TABL_ORDBANK-DIV,
 S_MATNO FOR ZSD_TABL_ORDBANK-MATNO,
 S_CUSTNO FOR ZSD_TABL_ORDBANK-CUSTNO ,
 S_QTNO FOR ZSD_TABL_ORDBANK-QTNO,
 S_QTDAT FOR ZSD_TABL_ORDBANK-QTDAT,
 S_QTVDAT FOR ZSD_TABL_ORDBANK-QTVALDAT,
 S_SONO FOR ZSD_TABL_ORDBANK-SONO.
SELECTION-SCREEN END OF BLOCK b1.
AT SELECTION-SCREEN.
 SELECT * FROM ZSD_TABL_ORDBANK
 INTO TABLE ITAB
 WHERE CCODE IN S_CCODE
 AND SORG IN S_SORG
 AND DISTCHAN IN S_DCHAN
 AND DIV IN S_DIV
 AND MATNO IN S_MATNO
 AND CUSTNO IN S_CUSTNO
 AND QTNO IN S_QTNO
 AND QTDAT IN S_QTDAT
 AND QTVALDAT IN S_QTVDAT
 AND SONO IN S_SONO .
 IF SY-SUBRC EQ 0.
 REFRESH ITAB.
 CLEAR COPIED_ONCE.
 CALL SCREEN 0200.
 ELSE.
 MESSAGE E012(ZQOTBANK) .
 ENDIF.
*& Module SET_STATUS OUTPUT
* text
MODULE SET_STATUS OUTPUT.
SET PF-STATUS '0200'.
SET TITLEBAR '0200'.
 IF COPIED_ONCE IS INITIAL.
 SELECT * FROM ZSD_TABL_ORDBANK
 INTO TABLE ITAB
 WHERE CCODE IN S_CCODE
 AND SORG IN S_SORG
 AND DISTCHAN IN S_DCHAN
 AND DIV IN S_DIV
 AND MATNO IN S_MATNO
 AND CUSTNO IN S_CUSTNO
 AND QTNO IN S_QTNO
 AND QTDAT IN S_QTDAT
 AND QTVALDAT IN S_QTVDAT
 AND SONO IN S_SONO .
 IF SY-SUBRC EQ 0.
 DESCRIBE TABLE ITAB LINES V_LINES.
 TCL1-LINES = V_LINES.
 ENDIF.
 COPIED_ONCE = 'X'.
 REFRESH CONTROL 'TCL1' FROM SCREEN '0200'.
 ENDIF.
 LOOP AT ITAB.
 QTY = ITAB-QTY.
 UPRICE = ITAB-UPRICE.
 TOT = QTY * UPRICE .
 ITAB-TOT = TOT .
 CLEAR: QTY, UPRICE, TOT.
 QTY = ITAB-CGL_QTY.
 UPRICE = ITAB-CGL_UPRICE.
 TOT = QTY * UPRICE .
 ITAB-CGL_TOT = TOT .
 CLEAR: QTY, UPRICE, TOT.
 QTY = ITAB-BHEL_QTY.
 UPRICE = ITAB-BHEL_UPRICE.
 TOT = QTY * UPRICE .
 ITAB-BHEL_TOT = TOT .
 CLEAR: QTY, UPRICE, TOT.
 QTY = ITAB-ALSTOM_QTY.
 UPRICE = ITAB-ALSTOM_UPRICE.
 TOT = QTY * UPRICE .
 ITAB-ALSTOM_TOT = TOT .
 CLEAR: QTY, UPRICE, TOT.
 QTY = ITAB-SIEMENS_QTY.
 UPRICE = ITAB-SIEMENS_UPRICE.
 TOT = QTY * UPRICE .
 ITAB-SIEMENS_TOT = TOT .
 CLEAR: QTY, UPRICE, TOT.
 QTY = ITAB-TELK_QTY.
 UPRICE = ITAB-TELK_UPRICE.
 TOT = QTY * UPRICE .
 ITAB-TELK_TOT = TOT .
 CLEAR: QTY, UPRICE, TOT.
 QTY = ITAB-OTH_QTY.
 UPRICE = ITAB-OTH_UPRICE.
 TOT = QTY * UPRICE .
 ITAB-OTH_TOT = TOT .
 CLEAR: QTY, UPRICE, TOT.
 MODIFY ITAB.
 ENDLOOP.
ENDMODULE. " SET_STATUS OUTPUT
*& Module SET_LINE_COUNT INPUT
* text
MODULE SET_LINE_COUNT OUTPUT.
LINE_COUNT = SY-LOOPC.
ENDMODULE. " SET_LINE_COUNT INPUT
*& Module UPD_OK_CODE INPUT
* text
MODULE UPD_OK_COD INPUT.
IF OK_CODE = 'SAVE'.
 UPD_OK_CODE = OK_CODE.
* CLEAR OK_CODE.
ENDIF.
ENDMODULE. " UPD_OK_CODE INPUT
*& Module EXIT_COMAND INPUT
* text
MODULE EXIT_COMAND INPUT.
SAVE_OK_CODE = OK_CODE.
CLEAR OK_CODE.
CASE SAVE_OK_CODE.
 WHEN 'BACK'.
 CALL FUNCTION 'POPUP_TO_CONFIRM'
 EXPORTING
 TITLEBAR = 'Order Bank Entry'
 TEXT_QUESTION = 'Do you want to Go BacK ?'
 TEXT_BUTTON_1 = 'Yes'
 TEXT_BUTTON_2 = 'No'
 DEFAULT_BUTTON = '2'
 IMPORTING
 ANSWER = ANSWER.
 IF ANSWER = '1'.
 LEAVE TO SCREEN 0.
 ELSE.
 ENDIF.
 WHEN '%EX'.
 CALL FUNCTION 'POPUP_TO_CONFIRM'
 EXPORTING
 TITLEBAR = 'Order Bank Entry'
 TEXT_QUESTION = 'Do you want to Exit ?'
 TEXT_BUTTON_1 = 'Yes'
 TEXT_BUTTON_2 = 'No'
 DEFAULT_BUTTON = '2'
 IMPORTING
 ANSWER = ANSWER.
 IF ANSWER = '1'.
 LEAVE TO SCREEN 0.
 ELSE.
 ENDIF.
ENDCASE.
ENDMODULE. " EXIT_COMAND INPUT
*& Module UPDATE_MOD INPUT
* text
MODULE UPDATE_ITAB INPUT.
 MODIFY TABLE ITAB FROM ITAB.
ENDMODULE. " UPDATE_MOD INPUT
*& Module SCROLL INPUT
* text
MODULE SCROLL_SORT INPUT.
SAVE_OK_CODE = OK_CODE.
CLEAR OK_CODE.
CASE SAVE_OK_CODE.
WHEN 'P--'.
 TCL1-TOP_LINE = 1.
WHEN 'P-'.
 TCL1-TOP_LINE = TCL1-TOP_LINE - LINE_COUNT.
 IF TCL1-TOP_LINE LE 0.
 TCL1-TOP_LINE = 1.
 ENDIF.
WHEN 'P+'.
 I = TCL1-TOP_LINE + LINE_COUNT.
 J = TCL1-LINES - LINE_COUNT + 1.
 IF J LE 0.
 J = 1.
 ENDIF.
 IF I LE J.
 TCL1-TOP_LINE = I.
 ELSE.
 TCL1-TOP_LINE = J.
 ENDIF.
WHEN 'P++'.
 TCL1-TOP_LINE = TCL1-LINES - LINE_COUNT + 1.
 IF TCL1-TOP_LINE LE 0.
 TCL1-TOP_LINE = 1.
 ENDIF.
WHEN 'SORTUP'.
 READ TABLE TCL1-COLS ASSIGNING <FS_TCL1> WITH KEY SELECTED = 'X'.
 IF SY-SUBRC = 0.
 SPLIT <FS_TCL1>-SCREEN-NAME AT '-' INTO HELP FLDNAME.
 SORT ITAB ASCENDING BY (FLDNAME).
 ENDIF.
WHEN 'SORTDN'.
 READ TABLE TCL1-COLS ASSIGNING <FS_TCL1> WITH KEY SELECTED = 'X'.
 IF SY-SUBRC = 0.
 SPLIT <FS_TCL1>-SCREEN-NAME AT '-' INTO HELP FLDNAME.
 SORT ITAB DESCENDING BY (FLDNAME).
 ENDIF.
ENDCASE.
ENDMODULE. " USER_COMMAND INPUT
*& Module TABL_UPD INPUT
* text
MODULE UPDATE_TABLE INPUT.
 CASE UPD_OK_CODE.
 WHEN 'SAVE'.
 UPDATE ZSD_TABL_ORDBANK FROM TABLE ITAB .
 IF SY-SUBRC EQ 0.
 MESSAGE I002(ZQOTBANK) .
 CLEAR UPD_OK_CODE.
 ELSE.
 MESSAGE E003(ZQOTBANK) .
 ENDIF.
 ENDCASE.
ENDMODULE. " TABL_UPD INPUT
Thnx
moni
Message was edited by: md monirujjaman
Message was edited by: md monirujjaman

Hi Moni,
The problem as I had replied in your earlier post is with the MODIFY statement.
MODIFY TABLE ITAB FROM ITAB. This statement will do the modifications based on the table key. When you have character fields as editable, then some problems are to be anticipated. In such a scenario, you must update the internal table based on the index, rather than based on key.
So consider using
MODIFY ITAB FROM ITAB INDEX TCL-CURRENT_LINE.
Where TCL is the name of the Table Control. Also observe the difference in syntax here, don't use the TABLE keyword for the MODIFY statement.
Please try it out and let me know.
Regards,
Anand Mandalika.

Nokia 5220 WHITE SCREEN PROBLEM *Help plz*

hello guys ... my phone's (5220) screen has gone White ... !! i have absolutely no idea what the problem is ! i took out the battery and put it back again .. but when i turn it on ..after the nokia logo the screen goes white again !! i cant do anything except for looking at the white screen...! the phone doesnt even turn off until you take out the battery !
I tried to connect it to my PC (via data cable) but the phone does not get connected with the PC suite !! PLZ HELP ME !!

Jimmyireland is right - anything that you could do yourself requires the phone to at least boot up properly, at the moment your phone is like PC with no Windows involved, it can't find its OS to start.
The 5220 is a series 40 phone, there is facility for a forced reboot, it needs its software to be reflashed which is why you need the Nokia service point.

Annoying iphone problems, help plz?

well, I'm having two annoying problems with my iphone, the first is that when I record a video or a photo, it does not save and the second is that it does not appear as a removable drive on the pc, SOMEBODY HELP ME PLZ :/

You should try to restore the iPhone using iTunes make sure you back up, see if it helps.
iPhones won't show as removable device if you are referring to be able to copy/transfer files similar to a usb flash drive. It is restricted based on Apple's specification altho it should appear as "Digital Camera Device" having access to your captured photo's or "camera roll" you should unlock your iPhone first before connecting to PC or Mac if you do have a password.
As of saving issues, try to restore the firmware by itunes or resetting through iPhone settings as reset or restore.
It should fix and work as normal, if it doesnt you can always go back from where you purchased it but it will. Goodluck.

WRH54G linksys setup problem help plz

i just bought the WRH54G linksys wireless-G home router. I put the cd rom in and i followed every step and i have everything in the right place but when it is at step 9 when u have to choose between DHCP, PPPoE, or Static Ip i dont know which one to choose so i go with DHCP then step 10 after i put in the passwords and click next and it is checking internet connection it says the router is not able to connect to the internet. try turning cable/dsl modem off and back on again. do you want to try again?. that is where i get stuck and i have tried to turn it off and back on again and i doesnt work. can anyone help me out?

I HAVE A DSL .. ROUTER PROBLEM
STAYS IN STEP 9 AS WELL ..
checking internet connection it says the router is not able to connect to the internet. try turning cable/dsl modem off and back on again. do you want to try again?
after some research am going to try to put MY MODEM in brigde Mode. maybe that'll fix the problem... Since it apears the linksys WRH54G is trying to connect to the internet DIRECTLY... i dont knoe .... first time newbe , i have a high level of computer experties.. but am having pro with dis NAW 25$ discounted outer.lol
I have DSL from verizon... in there instusction on how to.. the first thing is to put the MODEM that they issued A WESTELL into brigde mode .. and setup..
if anione gat this thing working after u gat this CANT CONECT TO INTERNET
the router is not able to connect to the internet. try turning cable/dsl modem off and back on again. do you want to try again?
please e-mail me with anifinding..
.thanks in advance

Annoying podcast problem help plz

hi guys,
first if this is in the wrong place, i apologise, as you can see a new user.
anyway, heres my problem,
i just got hold of an ipod mini, and i use my itunes extensively for podcast listening,and i have a problem regarding when it comes to syncing them with my ipod.
basically i would like my ipod to put any podcast that is listed as new in itunes on my ipod when i connect it.
and yes it does that fine.
but what problem i have is, when i come to syncing again, it will get the new ones ok, but it will remove all the ones previously put on there, and its annoying, as there are some i have not listened to yet.
is there a setting were i can get my ipod/itunes to put all new podcasts on automatically, but leave them on until i decide to remove them.
i have tried all the settings in the ipod/podcast settings, but none do that.
so any help guys appreciated.
is there a way to get my new podcasts on my ipod, but leave the others on.(and then what would be the easiest way to remove them when i do want them off??)

You should try to restore the iPhone using iTunes make sure you back up, see if it helps.
iPhones won't show as removable device if you are referring to be able to copy/transfer files similar to a usb flash drive. It is restricted based on Apple's specification altho it should appear as "Digital Camera Device" having access to your captured photo's or "camera roll" you should unlock your iPhone first before connecting to PC or Mac if you do have a password.
As of saving issues, try to restore the firmware by itunes or resetting through iPhone settings as reset or restore.
It should fix and work as normal, if it doesnt you can always go back from where you purchased it but it will. Goodluck.

Displaying problem Help Plz !!!

Hi all
For some reason i cant seem to get any applets to run on my computer, they just wont show up, if any one could help, sorry now if i am in the wrong room for this
Thanks

Go tp this Sun website http://java.com and click on Verify Installation. If it does not verify that Java is installed, try clicking on the install arrow, and start an install. If you have any problems, review the help pages there.

Z87 msi mpower big problem help me please auto turn off and never boot

i had bought msi z87 mpower from amazon 2 weeks ago while trying to open it, it just turn on and leds light up but no beep/ no display= no signal , i tried to take it out of case the same problem tried it with 1 stick of ram g-skill 1600 mhz 4g same problem i removed the vga card same problem i removed the ram , the motherboard didn't recognize it and power on led on but no beep nothing debug led all the time 00 , with cpu i5 4690k only some people told me , mobo didn't recognize the cpu because it's haswell refresh need update for bios , but how when i can't see any screen and it can't even boot just fan spin and leds light up nothing else , i sent it to some msi technical support in egypt to try to make bios for it , he told me he could bot it and update it from windows normally without any problem and he sent it back to me , while i took it to try at my home with my cpu the same problem motherboard didn't recognize my cpu , i had connected everything and as well wifi card with the pin and the 4 kits of 16 giga ram trying to power on same problem i did 1 restart and the motherboard never turns on again like dead
i get it out the case and removed everything except wifi card same problem no power i just removed the wifi card it turns on for 1 second the turn off automatically i connect it again, and mobo don't turn on again i just release this pin of wifi card out of mobo the leds turn on like if the pin of wifi card shorting the motherboard i don't know why i removed it at all and try to turn on the motherboard light up and fans works for 1 sec then turn off automatically like the motherboard shut down it self for safety i try to connect the vga card only with 1 ram and cpu but the motherboard don't turn on at all , so motherboard only turn on now with 1 ram and cpu just turn on for 1 sec and then off if i connect anything more it will not turn on at all same problem with other power supply i sent it back to technical shop they said it's just bios corrupted and nothing bad but they told me they can't make it because bios files on msi site doesn't work for some reason and they want to give me it back like that turn on/ off immediately what could i do , did they make something bad when i sent it to them at start because it was turn on normally and when i try it just 1 restart and full fail to power after that and they admit , they had work through it to windows and make normal bios update so what would be the issue , i feel like if wifi card made some short to the motherboard with it's pin or the bios failed ot recognize wifi card and failed after 1 restart i don't know where to start or what to do psu good cpu good ram is good tested what could make some motherboard no turn on , as well i have removed the battery for 5 minutes and try with it and i made clear cmos button still same and they said they didn't touch motherboard while making bios
help me please
pc spec:
cpu i5 4690k
mobo msi z87 mpower
ram g-skill 1600 4giga
vga zotac gtx 970 amp extreme edition OC
psu seasonic 600 watt eco
case corsair spec 03 gamming

Quote from: bassam.mohamed20 on 13-April-15, 02:46:28
okay tomorrow i will try another processor chip but what if doesn't work , same here i suspect it's bios so what could let some motherboard turn on and off immediately?
Bad CPU? bad Motherboard? Other stuff.
The only way to know is testing parts.
You said it already worked with another CPU. Did you check CPU socket pins?

IPod Problems help PLZ

i have a 80gb classic and it just stopped working all of a sudden. When i turn it on all it does is go to the apple logo and turn off. When i try to connect it to my computer it doesnt reconize it. what should i do.
Please help

Hello OZ1989,
And welcome to Apple Discussions!
With the iPod hooked up, I would try putting the iPod into [Disk Mode|http://support.apple.com/kb/HT1363] to help the iPod stay powered on and mounted in Windows "My Computer" as an external drive. If you are able to get it to stay mounted, I would attempt to reformat the iPod using the tools provided by Windows, and then [Restoring|http://support.apple.com/kb/HT1339] the iPod via iTunes.
Here are instructions on how to reformat your iPod.
http://www.methodshop.com/gadgets/ipodsupport/erase/index.shtml
Hope this helps.
B-rock

URGENT, Big Big Problem, HELP

Hello MSI gaming forum
Motherboard: Z87-G45
I am posting on this forum because my main pc has been effected and i cant do my course work. I turn on my pc and everything seems to be running. But on my display it says no signal. i've tried taking out the graphics car and using the integrated graphics and that didn't work. Tried taking my ram out and that didn't work. The hard drives sound like they are being read but there but my HDD Light on my case doesn't flash like it did before. And the on button one the case is supposed to tight up but now it isn't. I've tried resetting the CMOS but i cant even boot up into the bios because my display says "no signal".
Literally was working one day and then the next day it just didn't display anything.
Please can someone help me out because i have no clue what is wrong with my pc and struggling to do my coursework and now maybe falling behind on my work.

Quote from: reissjanda on 04-February-15, 22:31:23
Thanks for replying, I've done what you have said but it's hasn't worked, the fans still spin but again says no signal
So that means even using the integrated video on the motherboard (no video card installed) produced anything on the screen?
At this point, it can only be 2 things. Motherboard or CPU. Hard to say which it is without having something to swap into the system and find out.

Dv6 pavilion hardware problem HELP PLZ

My hard drive makes a clicking noise. I know its wrecked but i want to know where i can get a new hardrive that fits my laptop. Please help

You will need to call AppleCare and talk to a Customer Service representative. This is a user-to-user forum, and we cannot help you with this issue.

Stupid Question but BIG problem - Help!

I recently transferred all my music files from an external USB drive to my new internal hard drive. Now when I launch iTunes, it can't find find my music. I've tried consolidating the library but its no use. Maybe I'm doing it wrong? If I click on a song it asks me to find it myself, which is easy but I have over 700 albums in there! What <edited by host> have I done! Please help!!

Glad to help both of you!
H a p p y H o l i d a y s !

MSI Neo2-FR Raid problems help plz

ok well me and msi are not getting along...well i'm tring to install a raid-0 ...in the bios i changed it to boot raid instead of ide....then i went and made a raid 0 array...well i go to try to install windows and i press f6...then when its time to install the drivers from the floppy, it dont see the dam drivers on the floppy so i can get no further...and its weird because from the time i boot up the comp the floppy light stays lit the whole time whether there is a floppy in or not...it did not do that on my other motherboard...msi is a weird board...im ready to break it....can anyone help here

If you can't get your floppy drive/disk to work properly with Windows Setup, you can integrate the ICH9R RAID drivers into a self-made install CD using NLITE or XP ISO BUILDER. Both tools are easy to use and the procedure shouldn't take longer than 15-20 Minutes.

Big problems help plz

Similar Messages

Maybe you are looking for