Big Problems w/ 845PE Max-L

Installed today,
P4 2.2
M/B MSI 845PE Max-L
G/F ti4600
512. samsung PC2700
Upon startup,
I get power it seems to everything but, I have a blank screen and i hear 1 beep followed by 8 beeps. It wont go into bios or anything. Any help would be appreciated.
Thanks,
Ed

Ok...
Unplug all the IDE cables and re-attach JUST the HD cable from the MB to the HD making sure the connectors are on securely and are lined up with the connectors at the back of the hard drive fully.
If that boots to bios screen ok then shutdown again and re-attach JUST the floppy connector (again making sure it securely fitted to both MB and to the back of the floppy) then boot back to the bios screen again to check that its ok with the 2nd cable fitted, then shut down and re-attach the CD-ROM cable... again making 100% sure that all the IDE cables are attached correctly and securely both to the MB and to all components.
Bootup again to BIOS and see if everything is as it should be... (HD, floppy and CDROM all detected properly now?)
Now in the BIOS use auto-detect wherever needed to detect the size of the HD etc (im unfamiliar with your BIOS so the auto detect may not be required but try it anyway) save and exit the BIOS.
Spend a little time attaching the cables to make sure they are ALL attached perfectly... it is very easy to miss align them if you are keen to get the PC up and running.

Similar Messages

Harddrive problem on 845PE MAX (PCB2.0)

I have a harddrive that probably is dead or something, and I get two strange sounds when the bios is trying to detect the harddrive. I wonder if these are diagnosic sounds ? In that case, what are the problem when there are these 2 sounds ? ?(
Reason I ask, is that I wonder if there is a MB problem or a harddrive problem. The bios won't detect ANY harddrives now! X(

ACIDBURN88888888,
What is your PSU, how much output for +5V?
Go to this link, it'll give you lots of help you need. http://www.msi.com.tw/program/e_service/forum/index.php?threadid=1135&boardid=16&styleid=1
All the Best... :D!!!

Problem updating 845PE Max BIOS

I could not update bios from 3.30 to 3.40
During programming flash, it stops in the middle of progressive bar and shows programming
error message.
Do you know why? ;(

flash protection on in bios
ntfs on drive
http://www.msi.com.tw/html/support/bios/note/ntfs.htm

Problems installing windows2k pro on a 845PE max

hi..
i've recently bought 2 sets of msi 845pe max motherboards and started installing one of them. it was okie... then i started installing the other one but i can't seem to complete copying the files from the cd to the comp and will prompt me telling me that a file cannot be copied over. so windows cannot start up. i swopped components and it didn't work. so finally i tried swopping IDE cables and it worked perfectly..... so i've got a few spare IDE cables and used them and now my working system cannot work! is there a benchmark for IDE cables or wat seems to be the problem?
HELP!!!!!!!!!!!!!!1

Scurran08 wrote:
Thanks bob,
I have read elsewhere on the Internet that windows 8 is supported on bootcamp and that it works.
Sometimes yes, often no, but it is unsupported officially so you'll have to live with it.

845PE Max Problems :(

Hi,
I just installed the new 845PE Max 6580 motherboard.
My system specs are
3.06 ghz Pentium 4
512 MB PC2100 DDR SDRAM
Radeon 9700 pro with latest 3.1 catalyst drivers
SoundBlaster Live 5.1
DirectX 9.0
Windows XP
The problem is that the system randomly hangs without any bsod or any error. I cant hit the reset switch or power it off from the front. Only way to turn off the system is by switching off the button on the power supply at the back.
Any kind directx application (game or benchmark) hangs, be it 8 or 9. I thought it was as a result of directx 9.0 but it hung on 8.0 as well.
Random hangs also occur while playing any audio. Another thing is when i power up after the system after it crashed my logitech cordless mouse stops responding unless i swap the usb slot at the back.
I've updated the bios as well as the usb 2.0 drivers off the website but still no luck.

got the latest intel inf from MSI website. turned off hyperthreading as well in the BIOS.
the power supply came with the case i bought a week back. brand new... http://shop.store.yahoo.com/svcompucycle/silverchenming.html
still getting these random freezes. freezes on me while listening to music on winamp, running IE, watching any movie on windows media player and games based on the unreal and like engines. somehow games like nba, fifa work fine.
also i made sure the radeon power supply not being shared by any device. the PCI slot below the radeon is empty as well.
i bought the motherboard from newegg.com and the worst part is apparently i cant RMA it back!
its driving me nuts. please there's gotta be a way to fix this. i'm sure some people are running the MSI 845PE with the radeon 9700 pro without any problems.
god..its going to drive me nuts if i'm going to shell out $120+ more to buy a new motherboard if it comes down to this.

845PE Max SPDIF AUDIO out problem

Hi there,
1. I've got 845PE Max MB; C1,7GHz; 256DDR; W98SE.
I haven't got "S" bracket (I can't buy one), but I want to use digital SPDIF out.
I connect CINCH socket to pin #3 of JSP1 [SPDIF out] connector. And I have sound output via it to my amplifier (I can hear proper sound (analog) from movies and windows sounds).
The problem is, that when I open "Sound manager" from system tray & I see "AC97 Audio Config" Window & I check SPEAKER CONFIG tab -> I can't see "ENABLE SPDIF OUTPUT" check box to choose digital output.
Funny thing is, that some time ago I had digital sound (dolby digital) when I played some movie, but now I don't have it on the same movie.
2. Neither I don't have MSI DVD application on CDROM attached to the MB. Can I download it from some place ? Maybe it can help to switch SPDIF on ?
Looking forward for advice,
Regards,
M@rek

Unfortunatley i threw out my pc-speakers when i moved last but i could lend a pair to test. But i dont think it would change since i did put in a SB live sound card and put the same cord in that to the surround system and it worked perfeclty first try...
So my assumption here is that there is no error in the connection to the surround system but rather a error in the onboard ..if its a severd connection or a driver issue im cant tell.. but since i tested all driver as of 2 weeks ago i could possibly find. even went to c-medias homepage and downloaded thier latest drivers.. and no luck..

HELP !!!! ATI9700 Pro + 845PE Max = problem

Help anyone.. pls tell me what happen !!!!!!!!!!!!!
just got a new 845PE Max m/b + ATI9700 Pro. seem ok when boot up to WinXP. :]
BUT !!! when try to run my directx game the screen went rubbish... try with dxdiag .. same thing happen.. Directx 3D test show distorted screen... Only Direct3D test.. direct draw is ok
however if I try with Nvidia Ti 4400 ... everything is OK
why??? anyone encounter the same problem?? tell me what should I do??.. so sad buying the exp$$$$ ATI9700 pro.. but cannot play game with 845PE Max
?( X(

ok.. I found out the cause to this FAULT
it is the PS.. cos' the PS 3.3V is faulty.. only can o/p 2.8V that's why those graphic card like ATI 9700 Pro that require ext power to the card cannot work.. (hence GeForce 2 and 4 Ti 4400 can work, cos' they dun require ext power)
thank for all...

845PE Max-L problem with pci cards

Got a weird issue with the 845PE Max-L and was wondering if anyone else has come across this. I work in the RMA dept of a nationwide computer wholesaler and recently we've come across atleast 4 of these boards with the same problem. under windows xp it will not detect any pci cards. tried various sticks of ram, video cards, network cards, modems, usb cards, hard drives, pretty much anything we can think of to check for incompatiblities. did the latest bios flash, installed the newest updates in windows xp, but still cant get these boards to detect any pci cards whatsoever. yes we tried different power supplies and yes we tested the pci cards in other systems to make sure none of it was defective, all passed with flying colors. now here's the kicker, under windows 2000 it DID detect the pci cards, however i was unable to successfully load any drivers to any of the devices. We've made a call to our MSI rep to find out if anyone else has run into this or are we just dealing with a bad batch. unfortunatly noone from MSI has contacted us back yet so i decided to try and post here to see if anyone else has come across this odd situation. Any feedback would be much appreciated.

Weaksauce;
Two replies two separate motherboards. In reference to the 865 / 875 motherboards not recognizing PCI cards I think your link has something to offer. :biggthumbsup:I'm not going to go back and test it but the reason the PCI cards were not recognized may very well be that the old bios did not properly inspire the intel inf utility to install the correct drivers. The force method you suggest may well overcome that particular problem. I would still suggest that merely doing the BIOS upgrade first is the more elegant approach.
Regarding the usb problem with MS update, the inf chipset article would appear to have little to offer. The 845 MB uses the Intel 845 chipset which is ICH4 by the way. The updated inf utility was installed in as early in the process as possible.

845PE Max (6580 v.2.0) and Maxtor DiamondMax 9 Plus - Problem!

Hi!
My mobo (845PE Max - MS 6580 v.2.0) detecting my hard disk (Maxtor DiamondMax 9 Plus 80GB ATA133 7200rpm) as the drive working in UltraDMA/2 mode (ATA33). What is wrong? How can I set it to work in mode UltraDMA/5 (ATA100)???
Please, help me as quick as possible.
Best regards
Martin "Kenickie"

System: MS Windows XP Pro. No Service Pack 1 installed yet.
But it doesn't matter.
Disk is recognized as UDMA/2 by BIOS!!! I upgraded BIOS to newest (3.40) but it didn't help.
This Maxtor is connected as Primary Master, and there is a CD-Recorder (TEAC CD-W516EB) on the same cable as Primary Slave. Teac is also recognized as UDMA/2. At the secondary Controller I have CD-ROM Drive (TEAC x32).

MSI 845PE Max Motherboard TV CARD problems

hello,
i'm use to MSI 845PE Max motherboard and avermedia tv card. i'm plug in to avermedia anywhere pci slot in motherboard but not installed avermedia. error is "ACPI bios system motherboard extension" How i can install to avermedia tv card.. HELP ME..!
PoWeRGuArD

i'm plug in to avermedia anywhere pci slot in motherboard
dont understand this bit,try different pci slots

845PE MAX and MSI TI 4800SE Problem! Please Help!

I'm tring to upgrade to a TI 4800SE on the MSI 845PE MAX Motherboard. But windows XP won't boot. I can't get in the BIOS setup. Just the MSI logo at startup, and it retarts every 8 seconds. Please help! Tried uninstalled ATI driver first.
System:
P4 2.4Ghz
MSI 846PE MAX
ATI All-IN-Radeon
Windows XP

Is that video card 4x or 8x AGP. Not sure but I think that mobo only supports 4x agp.

Connecting Powersupply to 845PE Max 2 FIR

This is probably a stupid question but I rather ask a stupid question than blow up my new 845PE Max 2 FIR. This motherboard has 3 power connections. Do I need to connect the power supply to all three or do I just use the big 20 pin connector by itself?
Thanks in advance

Quote
Originally posted by digital_voodoo
You should connect all 3 connectors. Let me know what u think of the board
Thanks.
I got it up and running late last night. I didn't have time to mess around with it much, only to find out that when I set the high performance mode from the BIOS the system will not boot (no beep code, nothing. I had to clear CMOS and start over). I'll post more of my opinions about the board when I have more time to play with it.
Any idea why I would be having the boot problem in high performance mode? I have a P4 2.4B, MSI G4MX440-VTD8X Video Card, Kingston DDR333 512meg RAM, MAXTOR 40Gb ATA133 Hard Drive.
Thanks again and I hope you guys will understand that I am not only a newbie to this board I am also a newbie to building computers from scratch. :]

845pe max 2 and floppy drive probs

I've got a 845pe max 2 fisr mobo
My floppy drives' LED is continuously illuminated when I turn on.
Windows 98se says it's an NEC floppy drive even though I didn't insert any drivers for it or anything. When I put a floppy disk in to it the drive can't read and a message in windows indicates that there is no disk inserted.
The thing is the drive worked when I first set up my system but that is the one and only time. I suppose it's a positive thing that the LED works.
Any ideas anyone?

Don't worry, it won't hurt your motherboard. It definitely sounds like that's the problem (floppy cabble upside down). Simply spin it around, and it should fix your problem (the "key" as you put it is facing down on my floppy drive).
If that doesn't fix the problem, try using a different cable.

845PE MAX-FIR Gigabit Lan Prob

I just got 845PE MAX-FIR last week.
But I have prob with Gigabit Lan controller. Windows(2k) detects it alright and says it works ok; however, it can't detect lan cable if I insert it.
First, I thought it was prob with lan cable, so I installed old realtek lan card. And it works fine with old lan card.
So I send the board for repair and got a new board. BUT! it still won't detect if the lan cable is inserted. What should I do? It's not prob with ethernet controller(since it looks working fine under windows(98 & 2000) and not the prob with lan cable. Does Gigabite lan uses different lan cable? I heard it's not...then what is the problem? HELP!

I believe you require Catergory 6 Cabling, as we where studying this the other day in class :D

Big problems exporting a video in Media Encoder - detailed info

Problems with exporting media through Adobe Media Encoder.
Hi there. I am really confused now, writing this, cause my Premiere CS4 has worked pretty good the year I have had it.
So it has chosen a really bad timing to cause me problems.
I am working on a big musicvideo production. The whole video is now finished, and the labels and the artists are waiting for the video. But I’m facing big problems now. And I have tried everything to solve this, without succeeding.
·         When I export the video, the Adobe Media Encoder sometimes waits and waits and waits and waits, and nothing happens.
Screen shot:
·         When it does start, if goes to about 20%, and then it interrupts and give me "an unknown" error in the log-file:
Screen shot:
·         Sometimes when I open the project , it gives me the following message when importing the media files.
Screen shot:
·         The weird thing is that this only happens to the HD version. I have the same video in DV version, in a DV project, and it exports without any problem.
So PLEASE help me here, what shall I do??? I MUST finish this video!

And here is my log-file with all the attempts I've tried with different settings...
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD.prproj
- Output File: C:\Users\Pawel\Desktop\TheThingCalledLove-MasterCut-HD.wmv
- Preset Used: Custom
- Video:
- Audio:
- Bitrate:
- Encoding Time: 00:12:58
2010-03-09 11:46:46 : Encoding Failed
The Operation was interrupted by user
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_3.prproj
- Output File: C:\Users\Pawel\Desktop\TheThingCalledLove-MasterCut-HD-1280x720.wmv
- Preset Used: Custom
- Video:
- Audio:
- Bitrate:
- Encoding Time: 00:12:55
2010-03-09 14:09:21 : Encoding Failed
The Operation was interrupted by user
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_6.prproj
- Output File: L:\TheThingCalledLove.wmv
- Preset Used: Custom
- Video:
- Audio:
- Bitrate:
- Encoding Time: 00:07:57
2010-03-09 14:24:41 : Encoding Failed
The Operation was interrupted by user
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_6.prproj
- Output File: L:\TheThingCalledLove_1.wmv
- Preset Used: Custom
- Video: 1280x720, 25 [fps]
- Audio: 440 kbps, 44 kHz, 2 channel 24 bit VBR
- Bitrate: Compressed, VBR, 2 Pass, Audiences:1, Avg 5500,00 [kbps]
- Encoding Time: 00:07:38
2010-03-09 14:38:40 : Encoding Failed
Error compiling movie.
Unknown error.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_6.prproj
- Output File: L:\TheThingCalledLove.wmv
- Preset Used: Custom
- Video: 1280x720, 25 [fps]
- Audio: 440 kbps, 44 kHz, 2 channel 24 bit VBR
- Bitrate: Compressed, VBR, 2 Pass, Audiences:1, Avg 5500,00 [kbps]
- Encoding Time: 00:06:21
2010-03-09 16:50:42 : Encoding Failed
Error compiling movie.
Unknown error.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_7.prproj
- Output File: L:\Sequence 02.wmv
- Preset Used: Custom
- Video: 1280x720, 25 [fps]
- Audio: 440 kbps, 44 kHz, 2 channel 24 bit VBR
- Bitrate: Compressed, VBR, 2 Pass, Audiences:1, Avg 5300,00 [kbps]
- Encoding Time: 00:03:14
2010-03-09 17:10:49 : Encoding Failed
The Operation was interrupted by user
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_6.prproj
- Output File: L:\TheThingCalledLove_1.wmv
- Preset Used: Custom
- Video: 1280x720, 25 [fps]
- Audio: 440 kbps, 44 kHz, 2 channel 24 bit VBR
- Bitrate: Compressed, VBR, 2 Pass, Audiences:1, Avg 5500,00 [kbps]
- Encoding Time: 00:07:34
2010-03-09 19:49:06 : Encoding Failed
Error compiling movie.
Unknown error.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_6.prproj
- Output File: L:\TheThingCalledLove.wmv
- Preset Used: Custom
- Video: 1280x720, 25 [fps]
- Audio: 440 kbps, 44 kHz, 2 channel 24 bit VBR
- Bitrate: Compressed, VBR, 2 Pass, Audiences:1, Avg 5500,00 [kbps]
- Encoding Time: 00:07:35
2010-03-09 20:00:11 : Encoding Failed
Error compiling movie.
Unknown error.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_12.prproj
- Output File: L:\thu.wmv
- Preset Used: HDTV 720p 25 High Quality
- Video:
- Audio:
- Bitrate:
- Encoding Time: 00:30:15
2010-03-09 23:21:07 : Encoding Failed
Could not read from the source. Please check if it has moved or been deleted.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD-nest.prproj
- Output File: L:\Sequence 02.wmv
- Preset Used: Custom
- Video:
- Audio:
- Bitrate:
- Encoding Time: 01:35:20
2010-03-10 14:18:32 : Encoding Failed
Could not read from the source. Please check if it has moved or been deleted.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD-nest_1.prproj
- Output File: L:\Sequence 02.wmv
- Preset Used: Custom
- Video:
- Audio:
- Bitrate:
- Encoding Time: 00:11:16
2010-03-10 14:39:37 : Encoding Failed
Could not read from the source. Please check if it has moved or been deleted.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD-nest_2.prproj
- Output File: L:\Sequence 03.wmv
- Preset Used: Custom
- Video:
- Audio:
- Bitrate:
- Encoding Time: 00:24:50
2010-03-10 14:53:11 : Encoding Failed
Could not read from the source. Please check if it has moved or been deleted.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_14.prproj
- Output File: C:\Users\Pawel\Desktop\Sequence 02.wmv
- Preset Used: Custom
- Video:
- Audio:
- Bitrate:
- Encoding Time: 00:29:41
2010-03-10 14:58:02 : Encoding Failed
Could not read from the source. Please check if it has moved or been deleted.
Could not write XMP data in output file.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_15.prproj
- Output File: C:\Users\Pawel\Desktop\Sequence 02.wmv
- Preset Used: Custom
- Video: 1280x720, 25 [fps]
- Audio: 440 kbps, 44 kHz, 2 channel 24 bit VBR
- Bitrate: Compressed, VBR, 2 Pass, :0, Avg 6736,00 [kbps]
- Encoding Time: 00:13:57
2010-03-10 17:37:50 : Encoding Failed
Error compiling movie.
Unknown error.
Could not write XMP data in output file.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_16.prproj
- Output File: C:\Users\Pawel\Desktop\Sequence.wmv
- Preset Used: Custom
- Video: 1280x720, 25 [fps]
- Audio: 440 kbps, 44 kHz, 2 channel 24 bit VBR
- Bitrate: Compressed, VBR, 2 Pass, :0, Avg 6736,00 [kbps]
- Encoding Time: 00:07:55
2010-03-10 17:56:15 : Encoding Failed
Error compiling movie.
Unknown error.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_18.prproj
- Output File: C:\Users\Pawel\Desktop\Sequence 02.mpg
- Preset Used: HDTV 720p 25 High Quality
- Video: PAL, 1280x720, 25 [fps], Progressive, Quality 4,0
- Audio: 384 [kbps], 48 kHz, 16 bit, Stereo, MPEG
- Bitrate: VBR, 1 Pass, Min 4,00, Target 10,00, Max 18,50 [Mbps]
- Encoding Time: 00:16:03
2010-03-11 08:52:52 : Encoding Failed
The Operation was interrupted by user
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_19.prproj
- Output File: C:\Users\Pawel\Desktop\TTCL.mpg
- Preset Used: HDTV 720p 25 High Quality
- Video: PAL, 1280x720, 25 [fps], Progressive, Quality 4,0
- Audio: 384 [kbps], 48 kHz, 16 bit, Stereo, MPEG
- Bitrate: VBR, 1 Pass, Min 4,00, Target 10,00, Max 18,50 [Mbps]
- Encoding Time: 00:12:04
2010-03-11 09:08:39 : Encoding Failed
Error compiling movie.
Unknown error.
- Source File: C:\Users\Pawel\AppData\Local\Temp\TumboTTCL3-HD_17.prproj
- Output File: C:\Users\Pawel\Desktop\Sequence.mp4
- Preset Used: Custom
- Video: PAL, 1920x1080, 25 [fps], Progressive
- Audio: AAC, 320 [kbps], 48 kHz, Stereo
- Bitrate: CBR, 32,00 [Mbps]
- Encoding Time: 00:01:08
2010-03-11 09:10:41 : Encoding Failed
The Operation was interrupted by user

Big Problems w/ 845PE Max-L

Similar Messages

Maybe you are looking for