BigPond USB Modem and Airport Extreme 802.11n

Judging by the information I have found I do not think this is possible, but thought worth asking regardless.
I have a Telstra BigPond Wireless USB Modem (7.2) - is it possible to plug this into my AE base station to share with other devices?
Thanks
tkoe

If you are thinking about a plain USB-to-Ethernet adapter (the kind used to get Ethernet from a computer's USB 2.0 port), it is not going to work.
It may work if you can find a special device similar to this one, providing that the adapter manufacturer can guarantee support for the exact mobile broadband USB modem and network that you are using. If so, it should be possible to connect the Ethernet output of the adapter to the WAN port of the AirPort Extreme base station. I should add that I have not tested this.
Another way of handling a situation like this is to use a dedicated mobile broadband router with support for the USB modem/network in question (basically, something like these exemples). Telstra/BigPond may be able to suggest something suitable.
Jan

Similar Messages

Airport Express and Airport Extreme 802.11n

Hello,
I have a Airport Extreme 802.11n Base Station set up and a old Airport Extreme (the one before the 802.11n model) set up which extends the Base Station's signal.
Is the old Airport Express broadcasting the 802.11n put out by the Airport Extreme even though the Express is an older model?
Thanks!

No, the older AX (Airport Express) is not capable of communicating in 802.11n protocol. It would be 802.11g at best.

I have a pc running windows 7. I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport. The wireless router works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

I have a pc running windows 7. I got an Airport Extreme 802.11n Wi-Fi and the printer is now plugged into the Airport. The Airport works fine but the printer shows as offline in control panel and in word. The printer is a HP LaserJet CP1525nw.

+For now I have it set to Share Public IP address - Is this correct for my Network Setup with The Airport Extreme being the only router being used ?+
This would be the correct setting if the AirPort Extreme is connected to a simple modem (one ethernet port).
*Settings I have Enabled*
5 GHz name indicates that you have elected to use the option to assign a separate name to the 5 GHz network. This will allow you to "tell" compatible computers to connect to that network, rather than the slower 2.4 GHz network
Use Wide Channels is recommended for 5 GHz operation.
Interference Robustness often does more harm than good and should not be used unless you know you are in a area with a lot of wireless networks and you feel that your network is experiencing interference issues from a nearby network.

I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I h

I'm not sure how to post a message. I hope this might interest someone. The situation; 3 floors,I am having trouble with an an Airport Extreme, 802.11n on the top floor and a Mac Pro 3.1 on the bottom floor. Not always but often it has trouble seeing the Airport and making a connection. I have an older Airport Express, would it help to install it? would it work best if it was installed in the same room? should it be installed half way in between? Get another Extreme? The Mac Book Pro on the middle floor can see 11 networks in the neighbourhood if that might be causing a problem or would if I installed the Express. Thank for your consideration.

Thanks for your time ... I appologize for the font and colour, I compossed the question in pages and failed to notice the font colour as grey ... there are a variety of computers of various ages so I think it is using a setting that allows both 5G and 2.4 ... the connection to the Airport is thru a cable modem and cable does run throuhout the house ... maybe those hard wires would be a place to look at ... do you think that putting the 'Express' on the second floor might help ... thanks again ...

AirPort Extreme 802.11n as a wireless router and local network switch?

Good afternoon,
I'm curious if its possible to have the APE in wireless network mode and connect systems via hard line as well?
I have an AirPort Extreme 802.11n set to "Create a Wireless Network" mode that is attached directly to a cable modem for internet connectevity. My issue is that while all wireless devices (several iPods, two iPhones and three laptop computers) connect to the APE without issue (and have internet access), when I try to plug in a Windows 7 desktop computer via one of the ethernet jacks, Windows is unable to connect and shows the network as "unidentified," spitting back a private IP address as opposed to a local LAN (this behavior repeats for an Ubuntu Linux box as well).
Not sure if the APE is misconfigured, this is a Windows 7 issue or if its improper use on my part (though this also precludes me from connecting a gigabit switch to the APE).
Thank you,
Nathan

Properly configured, the AirPort should provide both wired and wireless network client with Internet access.
At this point, I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

USB Printing AirPort Extreme 802.11n

I've upgraded to the new AirPort Extreme 802.11n base station and am having troubles printing to printers that worked fine with my previous AirPort Extreme 802.11g base station.
Both USB printers are detectable for set-up in the Print & Fax Preference tab and can be printed to when hooked directly to my computer. They are also detectable for set-up in the Print & Fax Preference tab when hooked via the base station.
So, all set-up and settings are fine. The issue I am having which never occurred before is that the file is sent to the queue but is immediately labeled as stopped and will not print no matter what I try.
I've configured, reconfigured, reset,you name it but with no luck.
does anyone have any answers out there. Please help...

I have had the same issue repeatedly after upgrading to Leopard. I can no longer use my printer (Brother HL-2070N the "network ready one") with my airport extreme router. It used to show up before I updated to 10.5.2, now I can't even get it to show up at all. I reset the base station, unplugged, and then re-plugged in the printer, nothing worked. Then I tried to just delete it from my list of printers and re-add it, but now my computer can't find it! I didn't change anything on my network at all, and I had literally printed something just 10 minutes before I applied the update. Very frustrating for a $180 router.

I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but the printer won't work with the new one.

I recently installed an Airport Extreme 802.11N that I bought in May 2013. It replaced an Airport Extreme 802.11N that I bought in July 2007. My USB printer (Lexmark E350d) worked fine with the old Airport, but I'm having trouble with the new one. When I try to print, I get a USB Waiting message on the printer, and when I force a page to print by pressing Go on the printer, I get a page that says ERROR: syntaxerror OFFENDING COMMAND: true. . . .cvt . . . fpgm . . . x . . .lglyf . . . <..J head . . . STACK: / [ -mark- /sfnts I’ve tried shutting down the printer and disconnecting it and the Airport, but that doesn’t help. I reset the settings on the printer. I upgraded the Airport firmware and removed, reinstalled, and upgraded the Lexmark printer driver. After I upgraded the firmware and printer driver, a few pages printed correctly, but then I got the same syntax error page as before. Any suggestions for getting the printer to work correctly?

Use a powered USB hub between the AE and the printer.. the usb port does sometimes have issues.
Try deleting the printer in the Mac and reinstall it.. the change in AE can represent effectively a change of printer.. it is important to make sure that is all up to date.
Beyond that.. USB printers.. ughhh! Consider for two toners you can go and buy a proper network printer.

Speed issue with WDS, Airport Extreme, and Airport Express 802.11n

I have a Airport network set up using WDS and two airport base stations: an Airport Extreme 802.11n, and an Airport Express 802.11n. The Extreme is configured to be WDS main and is connected to my cable modem and other computers, while the express is WDS relay and acts as a switch.
I don't actually have any wireless clients connecting to the express. I'm using it to connect a mac with no airport card to the network by plugging it into the ethernet port on the express. For the most part, it works, and the mac gets a network address and can access the network. However, the connection speed from the Express to the Extreme seems slower than it should be.
Since both are 802.11n, and the Mac is plugged into the Express's 10/100 ethernet port, I figure the theoretical top speed that the Mac should be able to communicate with another device plugged into the Extreme is at around the same speeds as 100 mbps ethernet, since the 100 mbps ethernet connection should be the bottleneck in this case. In reality, the speeds are much slower: when I transfer files between a machine connected to the extreme (via ethernet) and my mac, the speed tops out at about 2 megabytes a second, if that.
I looked in the Airport Extreme's logs, and it indicates that the Express is only connected at 54 mbps, as though it were a 802.11g Express. I have no idea why this is! Also, the only wireless communication is between the Extreme and the Express, so one wireless device acting as a relay for another (and thus cutting the throughput in half) shouldn't be an issue.
Does anyone know why the speeds are so slow, and if there's anything I can do to improve them?

Hello Brian Kendall. Welcome to the Apple Discussions!
I looked in the Airport Extreme's logs, and it indicates that the Express is only connected at 54 mbps, as though it were a 802.11g Express. I have no idea why this is!
That is because you established a WDS which only runs in 802.11g. Since you have two 802.11n base station, you would want to take advantage of the "Extend a network" feature available with these base stations.
Here's a typical setup:
o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
o Open AirPort Utility and select the base station that will connect to the Internet.
o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
o Click AirPort in the toolbar, and then click Wireless.
o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
o Enter the base station network and base station password is necessary.
o Click Update to update the base station with new network settings.
(ref: Page 46 of "Designing AirPort Networks Using AirPort Utility.)

Airport Extreme 802.11n and PPTP

Hi,
I've posted this question earlier in the wrong forum. Sorry for the double post.
I'm thinking of buying an Airport Extreme basestation. A problem I have with my current setup (using Airport Express) is that I have to use an extra router between my DSL modem and the Airport to connect to my provider via PPTP. Looking at the specs for the Airport Extreme, it seems that the new base station supports PPTP. But I really want to be sure, can I use PPTP with the Airport Extreme directly, or do I need to add an extra router as I have now?
Many thanks,
Don
PowerMac G4 450Mhz DP

You probably should ask in the AirPort Extreme (802.11n) discussion area.

SERIOUSLY slow USB hard drive on the new Airport Extreme 802.11n

I have recently bought the new airport etreme 802.11n. Great little device, look wonderful on the office desk. I had some troubles getting it up and running on my machine but finaly got there in the end.
The USB hard drive is a great little addition that I was very excited about, untill I got it running. It is amazingly slow, for example I tried to copy a folder that contained 15 files which amounted to 135.6mb and it took 20 mins and 24 seconds to upload!
Is this just the speed that it should be uploading or is there somehting wrong with my settings.
I'm running on 3 bars of signal and the settings I'm using are:
connect with password (which is the same as the base stations password)
Automatically discover disks
Show in menu bar
If anyone knows the technical data for the transfer speeds and can confirm my queries I'd really appreciate it!
Thanks in advance

I have recently bought the new airport etreme
802.11n. Great little device, look wonderful on the
office desk. I had some troubles getting it up and
running on my machine but finaly got there in the
end.
The USB hard drive is a great little addition that I
was very excited about, untill I got it running. It
is amazingly slow, for example I tried to copy a
folder that contained 15 files which amounted to
135.6mb and it took 20 mins and 24 seconds to
upload!
Is this just the speed that it should be uploading or
is there somehting wrong with my settings.
I'm running on 3 bars of signal and the settings I'm
using are:
connect with password (which is the same as the base
stations password)
Automatically discover disks
Show in menu bar
If anyone knows the technical data for the transfer
speeds and can confirm my queries I'd really
appreciate it!
Thanks in advance
Does your drive meet these requirements?:
You can connect USB-based storage devices to an AirPort Extreme (802.11n). Learn which formats and protocols are supported.
The AirPort Extreme (802.11n) supports USB storage devices that have a block size of 512 bytes, and are formatted as Mac OS Extended (HFS-plus), FAT16, or FAT32. Not all USB storage devices use a block size of 512 bytes.
The AirPort Extreme (802.11n) shares storage devices based on the format used to initialize the storage device. For example, if HFS-plus formatting was used, AFP and SMB/CIFS protocols are used to share the device on the network. If FAT16 or FAT32 was used, SMB/CIFS protocols are used.
The AirPort Extreme (802.11n) works with disks that have a single partition and are not RAID volumes (no more than one volume per physical disk).
Note: Use AirPort Disk Utility to discover and mount AirPort Extreme-based volumes over the network.
William

Setting up Time Capsule with existing AirPort Extreme 802.11n and AirPort Express.

I already have and am using an AirPort Extreme 802.11n with an AirPort Express. I want to set up a Time Capsule 802.11n. Which is the best way to configure this?

... Which is the best way to configure this?
The answer depends on what you need the TC to accomplish. If all you need it to do is perform Time Machine backups, simply have it join your existing network in client mode. It would be if it were to connect to your existing router (presumably your Extreme), not through an "extended" wireless network (presumably your Express).
If you need the TC to "extend" your network so as to serve additional wireless clients, you can do that also. Configure it to "extend" the network created by your Extreme.
As you can see it's quite versatile.

AirPort Extreme 802.11n and PowerBooks?

I am about 1.5 seconds away from buying one of the new AirPort Extreme 802.11n base stations to work with my AirPort Express but I have some questions / concerns.
1) Is my Powerbook capable of being enabled to access an "n based network" or is my money wasted on a router capable of speeds my computer can not access?
2) Should my computer be capable of accessing this network, is the Airport Express Base Station I have capable of acting on this network in "N speed" too? I know the base station can be configured to act essentially as a relay to boost signal strength...if set up to do so will it dumb the speed down to "G speed"?
3) If 1 and 2 are true and the express base station dumbs the speed of the N router down, can I configure the airport express base station to ONLY act as a wireless conection to my stereo and not as a wireless router, so as to allow my Powerbook to access the "N" speed network but still broadcast my music wirelessly to the stereo?
Many thanks...I wish they just made this information clearer on pages like this:
http://store.apple.com/1-800-MY-APPLE/WebObjects/EducationIndividualCanadaCustom .woa/9804006/wa/PSLID?mco=F7D93AEF&nplm=D4141ZM/A&wosid=gE4h0LIBbghZ2sXpLP21Wij0 uPJ

Hey for any one still lookin....
1. It all depends on what your CARD is capable of. Your POWERBOOK is more then capable of "N" speeds. Your only limited on the bandwidth of the Cardbus slot. You would have to have a third party card to access the new "N" speeds tho. I'm not sure if the last batch of (pre MacBooks) Powerbooks even made it to the "G" standard. I know Apple just came out with a driver for the latest Macs that have an upgradeable Card and or Basestation to get to "N". I really don't think your Express is upgradeable.
2. You need to look at what models you have to figure out what their capable of. You should be able to go to Apple's web site to find out. Usually the Router will Dumb it down to the SLOWEST speed. Unless you were streaming your music, and playing a game online, and transferring a large file you shouldn't have a problem anyway. As long as you are not using the slowest product it won't dumb down.
3. Haven't got that far yet. I've used up all my brain cells getting this far, so good luck on your mission. Try starting another string with specifics on what you want to do.

I just purshased AirPort Extreme 802.11n wi-fi I was told to get the step by step direction on the internet and I am not able to find it can you help me

I just purchased AirPort Extreme 802.11n wi-fi I was told to get a step by step direction to install this wi-fi on line but I am not able to find it. can you please help me?
Helen

See this Apple video tutorial.
http://www.apple.com/findouthow/mac/#wirelesssetup
And this Apple doc:
http://manuals.info.apple.com/en_US/airport_extreme_5th_gen_setup.pdf

WDS networking issue - Airport Extreme (802.11n) and remote Airport Express

*Background Info:*
Airport Extreme 802.11n (Fast Ethernet)
Version: 7.2.1
Wireless Mode: Participate in a WDS network (set as main)
Network Name: @Home
Wireless Security: WPA/WPA2 Personal
Channel: 1
Airport Express
Version: 6.3
Wireless Mode: Participate in a WDS network (set as remote)
Network Name: @Home
Wireless Security: WPA/WPA2 Personal
Channel: 1
Radio Mode: 802.11b/g compatible
Connect Using: AirPort (WDS)
Connection Sharing: Off (Bridge Mode)
Issue
Please help as I'm having issues with my WDS network. I've setup using both the wizard and manual and also hard reset on both units to setup again but cannot get them both to communicate to one another. Both units are showing green LED under their configuration. For my last attempt, I've tried adding the Airport ID (MAC) of the Airport Express to the Access Control and also DHCP Reservations on the Airport Extreme but still no luck.
The Airport Express (setup as remote) does not even show up in the Airport Extreme's Summary as Wireless Clients. In the WDS tab, the Airport Extreme is set up as WDS main, Allow wireless clients box checked and WDS Remotes has the Airport Express' AirPort ID in the list. On the Airport Express, WDS is set up as remote, with Allow wireless client box checked and the Airport ID of the Airport Express in the WDS Main.
I can connect clients to both units. Both units are configured using the same Network Name and have the same WPA/WPA2 security key. The Airport Extreme (main) however is connected to my broadband so any devices or clients connected to it are able to get outside. Connected devices or clients are assigned IP address via DHCP with IP 10.0.x.x. If wifi devices or clients connect to the Airport Express (remote) they are assigned a completely different IP addresses 169.254.x.x, they are not able to browse the internet or talk to other clients connected on the 10.0.1.x network. The Internet Connection configuration on the Airport Express (remote) is Connect Using Airport (WDS) and Using DHCP. I've even tried manually and entered the IP address 10.0.1.199 that I had assigned to the Airport Express from the Airport Extreme and Router Address as IP of Airport Extreme (10.0.1.1).
I think I've tried everything but I'm still having this problem. The remote Airport Express is not extending my existing Airport Extreme network. Any ideas???

Christopher,
This may or may not be helpful, or it may be something you've already tried or are aware of so I apologize if that's the case.
I have been researching ways to set up the Dual Band Network supported by the AEBS and came across your post. I've got an AEBS and (2) AirPort Express set-up currently (AEBS is main and the Express are participating in the WDS as remotes) and I'm trying to configure one of the Express to utilize a 802.11b/g compatible network while the AEBS runs a 5Ghz 802.11n Only network.
AAR, since the AirPort Express are 2.4Ghz 802.11b/g ONLY (no support for 802.11n), you have to be sure to set-up your AEBS first and select "802.11n (802.11b/g compatible)" in the Radio Mode drop-down on the AEBS before you attempt to connect an AirPort Express. The AEBS should be set-up as your "WDS main" and the Express should be set-up as a "WDS remote" for the network you established when you set-up the AEBS.
Bottom line here is the Express won't be seen by the AEBS unless the AEBS is 'looking' in the 802.11b/g 2.4Ghz frequency.
Hope this was helpful.

I have a Airport Extreme 802.11n and I can't find the disc to install it... how can I install without the disc?

I have a Airport Extreme - 802.11n and I'm trying to install it -- but I don't have the disc. Any help would be so appreciated.

You don't need the disk, you can download and install the application that you need.
If you are using Windows 7, the link for the software is just below. Otherwise, post back to let us know what operating system your computer is using.
AirPort Utility 5.6.1 for Windows - Apple

BigPond USB Modem and Airport Extreme 802.11n

Similar Messages

Maybe you are looking for