Bios 3.40 - CMOS Reset needed after power off

I recently upgraded my 875P FISR2 board to the latest bios cause I hade some problems with my NIC. Everything works fine except when I power off the PC by the button or on the PSU the computer won't boot until i make a CMOS reset and redo all my settings.
Anyone else had these problems or something similar?
/M

Try increasing the DDR Voltage to 2.7v~2.8v and maybe borrow a more powerful PSU like Antec 430w with stronger rails to test the system out.
The current PSU is just at the entry level for your power hunger system though it may do just good also.
You may also want to use Memtest86 to test your RAMs health and for errors.
Lastly, I would like to know if you've done any changes in BIOS before your flash to the current one, if you did change some parameters before, I would recommend you to re-check your current BIOS settings and set to the parameters that you have done for the previous BIOS.

Similar Messages

C871 default config after power off - bad nvram?

Hello,
I have new C871 with default configuration. after reconfiguring and reload, my config is loaded from nvram. But after power off, is there default configuration. What's wrong? config register is set to 0x2102 (that's ok).
any ideas?
thanks, 
martin

I found the reason - construction 'bug'. reset button was always presset.

How to resolve "you need to power off" screen looping

I fitted a new hard drive to my MacBook. Have restored from a Time Machine back-up. I have the "you need to power off" screen but every time I power off and power back on I first get the Apple logo screen and then the "you need to power off" screen.
I have read elsewhere it is probably caused by restoring a Snow Leopard backup using a Leopard disc. So I think I need to do the restore again but can't get out of the "you need to power off" loop....

also see Resolving Kernel Panics and Mac OS X: How to log a kernel panic.
for Mac OS X 10.6 specifically, see this support article.
additionally:
What is a kernel panic
Technical Note TN2063: Understanding and Debugging Kernel Panics
Mac OS X Kernel Panic FAQ
Tutorial: Avoiding and eliminating Kernel panics

IPad WEP password required after power off.

Hi,
On my ipad mini I am required to re-enter my WEP password after power off.
Why is this and how do I prevent it from happening?
This does not occur on my mbp or iphone 4s.
Thanks,
Rob.

Although it should work flawlessly, for some reason mobile devices don't always play nice with WEP. You're far better off with WPA2 (security-wise) anyway. If you have the ability to change your network's security, it might be easier to just get away from WEP than to try to make your mini work with it.

HT2309 Do I need to power off the iphone 4s before remove the sim card?

Do I need to power off the iphone 4s before remove the sim card?

Thanks, I think so, too.
But Apple says "When changing the SIM card, power off the device prior to opening the SIM tray" in http://support.apple.com/kb/ht2309.

HT4623 Hello! Answer Why do not open pictures after power-off at iphone 3? Thank you!

Hello! Answer Why do not open pictures after power-off at iphone 3G? Thank you!

This problem is already two years.

Do I need to power off my iPad after each use?

I bought a new iPad. The problem is after each use I have to power off in Order to connect to internet. Is there something in settings I need to do in Order not to have to shut my iPAd off so often

That shouldn't happen. I almost never turn my iPad off unless I do so for troubleshooting purposes. There is nothing in the settings that you should have to "fix" either as long as WiFi is always turned on.
Try resetting your iPad and see if that helps.
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

Cmos reset needed every startup

Hi
i have a new system and i have to do a Cmos reset before every time i start
when i start i got the question
" Cmos settings Wrong
Cmos date/time not set
press F1 for setup
Press F2 for load default values and continue"
If i press "F2" XP loads and everything works OK
then i turn off and try to start
and No screen
OK reset Cmos and then back to the choice of F1 or F2
if i press "F1" i enter bios setup menu
and if i changes anything there and chose to save and exit (or press F10 )
it go black and no more happends
then i reset Cmos and start again and i am back with the choice of F1 or F2
( i have checked the battery and it had good voltage )
any ideas ?

Quote from: Maesus on 10-August-07, 14:34:57
hi,
I guess you didn't get the CMOS setup correctly. Just "Load Optimized Default" and Save and Exit. Don't change anything else. Does that work?
If not, "Load BIOS Setup Default" and see.
tried that
if i enter bios setup and exit without changes it will boot.
it seems that every effort to do any changes in bios results in black screen.
and i have to reset Cmos
Quote from: NovJoe on 10-August-07, 16:32:54
Can you try booting the system out of the chassis, by jump starting the PSU?
that seems a bit to advanced to me ???
it seems that i have to return the mainbord to the supplier
but thanks for yor support

Linksys SGE2010P resets after power off

Hello,
i got a linksys SGE2010P and when i configure it and save it works fine but after a power off the settings are back to default. someone an idea ?
Rensk,
Solved!
Go to Solution.

i used to have the same problem in my SFE2000 until I have learned that you need to do the following steps to permanently save your settings
go to Admin > File Management > Copy Files
click on Copy Configuration button
set Source File Name as Running Config
set Destination File Name as Startup Config
click Apply

Lumia 625 wont start after power off!

I bought a lumia 625 5 months ago and it worked fine. but recently when i switch off power it wont turn back on. So i had do keep it in air plane mode at night. After like one hour it switches on back. I tried resetting and restarting. Phone only vibrates after i release power key ( in all resetting methods), but does not show anything in the display. How can i fix this. help would be appreciated

I'm going to suggest a hard reset of the phone. Do a backup first, then either go to Settings/About and select Reset my Phone, or for the 625:
Warning! All data will be lost!
1.Power off your phone
2.Press power button and after phone vibrates once press volume down until you will see exclamation sign on the screen
3.Press in this order:volume up
volume down
power
volume down
4.Wait until format ends and the phone restarts
I'm thinking that something with the sleep mode has gotten corrupted in memory. If this doesn't clear the problem, then you likely have a hardware/firmware fault and the phone should be taken in for repair or replacement.
/drt

The wireless connection keeps going away and I need to power off and on the time capsule to get the wifi network up

Time Capsule wifi access very poor. it keeps disconnecting and i need to power on and off thr router to get the wifi connection back again. When it works its so slow, it works only in the roms nearby and not even upstairs in my home!

I cannot work from the serial number.. I need the model number. A1xxx in the rubber .. in the rubber.. for Gen1-3.. 2010 is probably Gen3 but can be early Gen4.
Follow up questions:
How do i take the firmware back to 7.6.1 or 7.5.2
wireless names are Room of requirement and Leaky Cauldron - Is that too long a name?
How do I set fixed wireless channels?
Can relocate. Its in the main level of the house to give me access upstairs in the bedrooms and down in the basement,
Change firmware.. hold down option whilst clicking version.
Wireless names.. short, no spaces and pure alphanumeric.. yes.. your names are wrong.. from my point of view.. more they do not obey the rules.. no spaces.
Check C9 here why this is important.
http://pondini.org/TM/Troubleshooting.html
Fix wireless channels.. option page in wireless are of utility.. you need to spend more time in the utility so you know what is there.
Location is everything.. sometimes you simply need more than one device.. wireless has limited range. Use ethernet or EOP - homeplug adapters to place another AP in area closer to your position.

Reconfig required after power off

A week ago I changed my previous router by a new WRT54G. Old problems are gone, but unfortunately I got a new problem:
Each time the router is restarted (power off), I'm no longer able to connectwireless (Authorization, using WPA2 personal).
It needs always a wired connection first, then connect to the router setup:
Wireless - Wireless Security - Save Settings (without change). It looks like some settings are not saved correctly!!
Any help is highly appreciated.

Return the router. The new WRT54G hardware versions (v5, v6, v7, v8) are known for their various issues they have. Replace it with a WRT54GL which is the old hardware platform they have used for the first versions which work far more reliable.

Bad vi after power off

sometimes LV can't open VI if system crushed (power off) when this VI is opened by LV
this trouble appear not every time.
I had experimented with this trouble and not found any rule (about dozen attempts and no problem with vi)
But yesterday I was on customer object and system crushed (power off) twice. After second crush I had found that can't open main VI (attached).
This error was in LV6 (my first version), in LV7 fnd now in LV8 (8.3)
I'm not sure, but may by bad file is smaller than correct file (from backup).
Why this happen and how can I avoid this error?
Attachments:
data_processing.vi ‏231 KB

Hi Artem,
I would not call it a LV-error when you switch-off (or crash) your pc while working... How should LV prevent from crashing?
There is no other answer than 'save early and often'! And starting from LV8 there is an auto-save option similar to MS Office (save every x mins)!
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Satellite P300 156 PSPC4E - White Media LEDs stay on after power-off

HI
I have a Toshiba Notebook Satellite P Series P300 156 (PSPC4E) which has just developed a problem
When I power off, the laptop shuts down normally and power button itself goes off, but the 6 white media LED's to the right of the power button remain on constantly. The only way to get these to turn themselves off is to disconnect the battery.
Can anyone please advise
Many thanks

Thanks for the replies
I tried altering the BOIS, but that only affects the illuminated strip along the top of the mouse touch pad.
I cant remember which version of BIOS that I got (I'm at work at the moment) but I tried downloading the latest from here (dated 18/03/10), and it made no difference.
Its a strange one. The lights stay on even if the laptop is closed for long periods. They just never go off, unless I take the battery out.
Message was edited by: hawkerpaul

Cannot establish wireless connection with WRT54G after power-off

My WRT54G (firmware v7.00.0) is connected to cable TV modem and
usually the wireless connection works fine, but after swiching off and later
on the power to WRT54G a laptop cannot establish WiFi connection to internet.
I can see in Odyssey software (for wireless communication) that my laptop
found the right network (SSID) but in status it says 'waiting for keys'.
I use WPA2 (TKIP). The laptop does not connect to internet.
When I connect it by cable (ethernet) the internet works fine, I have noticed
that by accessing the web-page utility of the router and simply clicking
save changes on wireless-settings page (without making any changes in
the settings) my laptop instantly establishes wireles connection and
everything works fine till next power swich-off.

Thanks for reply! I have my network in preffered, and the software/laptop locks on
the network (see it, says it have excellent signal strenght) and gives note
'waiting for keys' (the WPA2 encription key is in the settings - both of router and laptop client - Odyssey).
I've got firmware ver.7 so it is probably the latest.

Bios 3.40 - CMOS Reset needed after power off

Similar Messages

Maybe you are looking for