BIOS CD-based update using the USB CD-ROM?
I'm trying to update my x200 BIOS, but since I'm running Vista x64 I am unable to use the BIOS updater directly from Windows.
Consequently, I downloaded a bootable CD-ISO from the Lenovo support site and burned a bootable CD-ROM. Unfortunately, I am unable to start the updater from it. I changed the boot order and it does spin up the CD and boots _something_. But then it just shows a blank screen and a blinking cursor on the top left corner. Eventually, the CD-ROM will stop spinning and it just sits there.
I tried to use a different program to burn the ISO but I get the same effect :-(
I searched a bit and found that apparently the Lenovo BIOS-Update ISOs for the previous X60/X61-series did _not_ work from the USB CD-ROM, only when used with a CD-ROM in the docking station:
http://www.thinkwiki.org/wiki/BIOS_Upgrade/X_Series
Do people know if this is still the case for the x200 series? On the Lenovo page, it does say that this x200 BIOS update CD should work with both "the USB types or Ultrabay Slim types". However, my experience suggests that it still does not work. Have others been able to make this work?
cheers,
-m
Solved!
Go to Solution.
Fixed: Burned cd with Active ISO Burner, instead of Roxio.
Found the fix here.
http://forums.lenovo.com/lnv/board/message?board.id=T400_series_ThinkPads&message.id=4513&query.id=1...
Similar Messages
-
i have an iphone 4, i connect it to my laptop using the usb and then when connecting to itunes it says my phone is not up to date with itunes yet i cannot find an update 11.1 for my phones itunes? someone please help me.. kind regards
Itunes 11.1 is for your computer, not your iphone
It is required in order to sync with ios 7. -
When I plug my iPhone or iPad directly into my lap top, using the USB cord, the devices don't even register with iTunes as being present. I am completely stumped. I believe this bagan with my last iTunes update. The last time I syced any device was Oct 23, 2013. During that time I bought two new apple products and the same problem, when I plug them in they do not even show up as being available to sync. Any ideas why this is happening?
iPad not appearing in iTunes
http://www.apple.com/support/ipad/assistant/itunes/
iOS: Device not recognized in iTunes for Mac OS X
http://support.apple.com/kb/TS1591
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
iTunes for Windows: iTunes can't contact the iPhone, iPad, or iPod software update server
http://support.apple.com/kb/ts1814
iTunes for Windows: Device Sync Tests
http://support.apple.com/kb/HT4235
IOS: Syncing with iTunes
http://support.apple.com/kb/HT1386
Apple - Support - iPad - Syncing
http://www.apple.com/support/ipad/syncing/
iTunes 10.5 and later: Troubleshooting iTunes Wi-Fi Syncing
http://support.apple.com/kb/ts4062
iOS: "Not enough free space" alert when trying to sync
http://support.apple.com/kb/ts1503
Cheers, Tom -
i just upgraded my iphone 3gs to ios 6 not sure if it updated but now when i turn on my phone it says automatically that i need to connect it to itunes using the USB port but when i connect it it comes up as new hardware and cannot find a program/software for my device even though i have the latest itunes on my computer. i have tried reinstalling itunes but it still cannot find my phone and now i cannot use my phone as it is stuck on the sync to itunes screen
Have you downloaded and installed the latest version of iTunes from here:
http://www.apple.com/itunes/download/ -
I'm new to this and I think I typed a long heading!
Anyway the issue is I have iTunes and just updated it to the latest. I also have various Apple devices however my iPhone won't sync with iTunes. When I connect it using the USB cable it does not appear in the top right corner as does other devices. The cable is fine as it charges and also my PC sees the device. However it does not appear in iTunes so I can't sync music to it.
I've searched the web but all asume iTunes can see the device.
Help!?Hi David,
If you are having issues with your iPhone not being recognized by iTunes on your Windows machine, you may find the troubleshooting steps in the following article helpful:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/ts1538
Regards,
- Brenden -
I was in the middle of installing the new update using the wifi at a local restaurant when I lost the wifi signal and my iPhone shut down, and now I can't get into the phone. I only get the iTunes logo with the cable pic. What are my options now?
Your only option is to connect your iPhone to your computer via USB (as the diagram indicates) and restore using iTunes.
-
Can you program a Slave's Node ID or Zone ID using the USB-8476 as the LIN Master?
I am planning on using the USB-8476 LIN interface as the LIN bus Master in an application. The application would require the USB-8476 (Master) to program a Node ID and Zone ID into a slave device that is on the LIN bus. The slave device is a PIC12F1822 mcu + MCP2021 LIN transceiver. After reading through the User/Software Manual for the USB-8476, it does NOT seem possible to assign an ID to a slave device. It seems like you can only communicate with slaves that already have an ID programmed into their memory. The Node/Zone ID terminology is used by our customer and may not conform exactly to the IDs associated with LIN. I am new to the LIN world, so please let me know if you need more information about what I'm trying to accomplish. Can you program a Slave's Node ID or Zone ID using the USB-8476 as the LIN Master?
No need to respond to this topic. The company that builds the slave device has a communications specification that was recently provided to me. I should be able to use the NI USB-8476 and a call to the ncWrite function (NI-CAN Frame API function) to accomplish my goals.
-
When i connect my iphone 5 to my pc using the usb cable, my device is not recognized yet when connected to a power source, it charges normally. What should i do to rectify the problem and read sth about debris being in the usb. How do i remove that?
iOS: Device not recognised in iTunes
Windows: http://support.apple.com/kb/TS1538 -
Can I use the USB cable that came with my digital camera to conect camera to iPad by connecying the camera cable to the USB end of the iPad cable? I have a double ended USB connector if necessary.
No.
You need to use this.
http://store.apple.com/us/product/MD821ZM/A/lightning-to-usb-camera-adapter?fnod e=3a
or this
http://store.apple.com/us/product/MD822ZM/A/lightning-to-sd-card-camera-reader?f node=3a -
I got my cousin's old I-Pod as a gift, but when I hook up the I-Pod to my computer using the USB so I can put music on it, it doesn't register as being plugged in. What should I do? I also cannot figure out how to change who's I-Pod it is. Can anyone help me out?
- I would try resetting the iPod:
Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
and then try restoring it. This probably will not work but is worth a try.
- Next I would disconnect the iPod from the computer and let the battery fully drain. When drained, charge it for at least an hour then:
-- Try resetting it as above and see if iTunes will see the iPod. If it does, then restore the iPod.
-- If not in iTunes try placing the iPod in recovery mode to see if that make the iPod visible in iTunes. If it does then restore via iTunes
-- Last, place in DFU mode to see if that makes the iPod visible. If it does then restore via iTunes. -
I have my iPhoto set to an external drive, when it was in use the usb disconected as i was moving my mac air, when i re-conected a message said (your photo library is either in use by another application or has become unreadable).
I have tried shutting it down and then re opening iPhoto but get the same message.
The reason for the external drive was there was not enough room on my hard drive, I have around 7000 photos on it.
is there a simple fix?
Regards
DaleThese are your options:
1. Restore the iPhoto library from the most recent backup that predates the issue.
Advantages: Always works, if library damage is causing the problem and the backup is intact.
Disadvantages: Impossible if you don't have a backup. All changes made since the backup are lost.
2. Repair or rebuild the library. Be sure to back it up first.
Advantages: May solve the problem with no loss of data.
Disadvantages: May fail. May take a long time if the library is large.
3. Scavenge the library with a third-party application called "iPhoto Library Manager," which you can find in a web search. From the application's menu bar (not the iPhoto menu bar), select Library ▹ Rebuild.
Advantages: All images and albums should be preserved.
Disadvantages: All books, calendars, and slideshows will be lost. -
I am trying to connect my iPad mini to my Samsung camera using the USB camera kit, I keep getting the error message ' device to powerful'. Is there anyway to fix this or do I need to take it back?? The shop assistant in Currys assured me it should work and it wasn't cheap at £25 for a tiny wire! I have read other posts concerning this but they are dated quite a while ago so just wondered what the newest advice was concerning this. Thanks
The camera is drawing too much power for your iPad. This can happen on cameras which charge their batteries using the USB connection. Make sure that you have the camera set to the correct settings for picture transfer - check the documentation that came with the camera.
Note that you can return the USB kit and get the SD card adaptor or get a powered USB hub if you can't get the camera to work any other way. -
I have an iPad 3 if I use the USB cable can I print to any printer no connected to a computer
I have an iPad 3 if I use the USB cable to any printed not connected to a computer will I be able to print
No. iPads print only wirelessly. You need an Airprint capable printer,
or a network printer reachable wirelessly or a printer that can make
its own ad hoc wireless network. There is no USB connection on an
iPad.
What type (manufacturer & model) are you trying to print to? -
Ipad2 Camera Connection Kit
When I connect using the USB option I get a screen on the ipad which says "Accessory Unavailable. The attached accessory uses too much power"
What should I do please?
DavidI believe your camera uses a micro SD card. The CCK accepts the full size SD card. Do you have a SD card adapter to plug the micro into?
Cheers, Tom -
iphoto 9.5 won't import photos from iPhoto 7.5. Library will not update using the iPhoto library upgrader application. Repeatedly says it can't locate photos even when told to cancel. I think the photos in question are in Nikon RAW format.
iPhoto 9.5 immediately tries to "upgrade" my library using the upgrader.
iPhoto 9.5 asks you to run the upgrader to prepare the library for 9.5. It then will update the library to its format.
You need to do the following:
1 - go to your Applications/Utilities folder and double click on the iPhoto Library Upgrader 1.1 application.
2 - select Choose Library, navigate to your iPhoto library, select it and let the upgrader do its thing.
3 - launch iPhoto 9.5 to open and finish the conversion of the library.
OT
Maybe you are looking for
-
I no longer have any disks for my airport extreme (its pre-time capsule)... how can I connect my windows machine to it in order to get to the internet?
-
Resource is not visible in workbench Aplication View
Hi, When i write any file into the repository from Java API or Dotnet services using writeResource(), then I am not able to see this resource from Application View in Work bench. Though i am able to read the resource using API but not able to open it
-
Phantom Frame Appears Between Two Clips
I am new to FCP. When I play my video in the timeline, a phantom frame from another clip plays between two clips. I don't know if I accidentally placed one of the clips on top of it or something when I was moving clips, but I can't figure out how to
-
How do i uninstall adobe cs6 from windows 8
Dear Sir/Madame, Due to I got the old one windows 8 (genuine license) notebook from my brother and it's install pirate adobe cs6 include this notebook but I don't use this program suite and I prefer to recover disk space. I try to uninstall in every
-
Narrative Reports based on multiple records
Hi experts, We are trying to build email template via SOD report (similar to mail merge template, but the SOD report can retrieve data from multiple record types). What we are thinking is to use narrative report...but we are not able to create the re