Bios does not recognise cr52-m drive

I recently updated the aspi drivers because I had a dvd rom which needed it, but it now seems that the cr52-m is now not reciognised by my bios.
This means Nero does not recognise the drive and on 2k pro the logical disc manager now takes several more minutes in loading.
I have searched the msi site looking for the firmware or driver for the drive but cannot find anything which can help me.
Live monitor does not give me anything useful to solve this problem.
So if support or any other forum member can point me in the right direction so I can resolve this issue so that my bios can recognise the drive again by flashing the right firmware, I will be happy to continue using msi products.

what is aspi driver?
Also, try to contact MSI by phone and e-mail about your problem as well not just this forum.

Similar Messages

K9N2 Diamond - bios does not recognise Intel SSD 520 series

Hi,
I have a K9N2 Diamond motherboard and BIOS v2.7. I recently bought an Intel SSD 520 Series and when I connect it, the BIOS does not recognise the HDD at all. When I try to install Windows 7, the HDD is shown at the list, but it says that I can not install Windows at the HDD.
I have tried to connect the HDD at SATA port 5 and 6 and set the RAID mode to ACHI and also at ports 1 and 2 and set the RAID mode to IDE. Nothing works.
Any ideas?
Regards,
George

.and does the problem appears using the HDD which was equipped in this notebook?
If the BSOD would not appear using the HDD, then a problem is realalted to the inserted SSD drive.
In many cases firmware updates are released for SSD drives and in some cases this might be a solution.

Help my computer does not recognise my hard drive

Hi All,
Yesterday I turned my computer on to find that it would not start up. I tried following advice etc about starting up in safe mode etc but no help what I have found is that he computer does not recognise the hard drive anymore so when I out the osx install disk in and run system profiler and disk utility it does not show a hard drive. I have not done anything for this to happen. Can anyone help me with this.
Thanks.
Paul

Instead of using older OS X CD/DVD install to a new drive.
Where is your backup and clone?
Buy some drives! that is a must.
Pick up a FW case, you will need it to put the old drive in, and later, so you have an external and off line drive for backups and maintenance.
A copy of TechTool Pro 4/5 and Disk Warrior (DW first).
SuperDuper to clone your drives.
Demo of Prosoft Data Rescue 3 to scan the drive once you have a system and you put the 'dead' drive in FW case.
Then do backups and preventative maintenance on a very regular basis and have at least two backup sets.
If you have been doing that, and know and have read those instructions in the past....

ITunes does not recognise USB Flash Drive

Hi everyone,
I am repeating this request in the hopes that the daytime crowd will have someone who can help!
I plug a usb flashdrive into my MacBook with iTunes active.
It comes up on desktop.
It does not appear as device in iTunes.
I can move files (albums) to the device from music menu under Go.
I cannot save my playlists from iTunes.
How do I get iTunes to recognise the usb drive.
Thanks, Steve.

Hello Limnos,
Thanks again for all your help.
Since my initial response I've looked in a little more depth at the track names.
All my files are stored and played at CD quality from the original CD rather than MP3.
It appears that track names are extracted from the Library and look a little different from those that appear in the iTunes playlist.
I see now that the first element of the track name is the track number from the original CD. So if my playlist is made up of 3 CDs then all the track 01s get stored first and played first, followed by track 02s etc.
I do not think it will take a great deal of effort to renumber the tracks from 01 to xty in what ever order I want them played since I usually play complete albums all the way through.
Thanks again, Steve.
BTW. Based on this I went out today and bought an 8Gb flash drive that I shall use to take our music with us on holiday. Saves a great weight in CDs! (and lets us get under new airline weight restrictions)

My laptop compaq presario cq56 does not recognise my usb drive hp usb flash drive v195b

I have a lot of problems with flash drives and card readers which plug into my usb ports being detected, I have just bought a new 16 gb flash drive (HP) as above which says on it plug and play, but when I plug it in I can't find it, there is no prompt and if I go to remove usb it does not show there either, I have about six card readers and they worked when I first used them but now I think there is only one that works. Can you help please?
This question was solved.
View Solution.

Hi
Please find the weblink given below might help you to fix the issue.
USB Device Troubleshooting
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Sdatellite M100 does not recognise CD/DVD drive in Windows XP

In device manager it is listed but with a yellow explanation mark.
No mention of it in my computer.
No icon.
I am able to open the drawer and i have put several types of cd/dvds in their with no results.
The light flashes orange on the drawer door. The drive is listed as 'Mat****advd-ram uj-841s-(sm) ' in the bios under boot devices.
I am trying to figure out how to remove the drive and replug but it seems i have to take the thing apart to do it and am hesitant without a diagram.
There is only a user guide in the downloads on this site so any help is appreciated :0)
Oh i also downloaded the driver from this site for the drie. Previous to that i uninstalled the drive in device manager but there was no change when i installed the downloaded driver.
Just using a Ubuntu Linux live cd and it is running.
Unfortunately its going to be hard to know for sure what is the issue this way as i don't want to install ubuntu on this machine as it is someone elses machine and they are far from ready to try linux.
I am in a live session now.
Ah ok when i go into the media folder there is no mention of the cd/dvd drive.
So there really is a problem unless i can physically unplug it from the mb and replug :0( Oh wait here it is...under 'cdrom' folder' but only files with a relevence to installing side by side with windows are mentioned...exe files, wubi etc.
Ah ok this is beyond my experience.
Can anyone give this amateur a tip?

First of all remove the ODD (CD/DVD) drive from the list in device manager.
Then access the registry and remove the Upperfilters and Lowerfilters values completely from the following registry key:
HKEY_LOCAL_MACHINE \ SYSTEM\ CurrentControlSet \ Control\Class {4D36E965-E325-11CE-BFC1-08002BE10318}
Finally you should reboot the unit.
After that windows will recognize the ODD again

My 2010 imac does not recognise my time machine since I had the Seagate replacement hard drive. Any thought from anyone? The External hard drive is a 1 TB seagate

My iMac (2010 intel model) does not recognise or communicate with my external seagate drive as a time machine for back ups since I had the 1TB Seagate replacement hard drive as part of the replacement prgram with OSX LION 10.5.8 installed.
Is this because I need to update the time machine drive itself?

This excellent Support article may help you solve that TM problem:
http://pondini.org/TM/Troubleshooting.html

My external hard drive does not recognise password

Hi,
I had formatted an external drive with a password security recently and using it as my portable time machine for backups. For some reason, the drive cannot be mounted as it does not recognise the Password. Can anyone please help me on this matter?

Does the drive show up under 'Devices' in Finder?

Bios does not see hard drive

My hard drive failed, and the bios in my T-40 does not recognize the new hard drive.
The new drive works fine in my T-30.
Johnsfo

The drive did not come with a jumper, but I did use one from another drive. When I placed the jumper in one position and booted, I was able to come to the BIOS and try to auto detect drive with no success. Then I switched to the second position and booted, a message showed "Scan devices, Please wait". The next message said "Hardware initiate failed, Please check device!!! The BIOS does not be installed. Press (g) to continue". When I pressed g it went to boot from the CD drive. So I put the Windows disc in, but it came to a point where it noted no hard drive detected.
Saying all this this is my first SATA drive, perhaps there is a motherboard jumper switch that I am unaware of.

Error code 43 with message 'one of the USB device attached to this computer has malfunctioned, and Windows does not recognise it'.

i have suddenly got this message 'one of the USB device attached to this computer has malfunctioned, and Windows does not recognise it'. it says error code 43. the usb drives (2 in no.) have stopped working as in they dont recognise the external hard drive
or pen drive. I have a HP pavilion dv4 series notebook. the usb drives were working fine - however suddenly yesterday this strange message cropped up. life has taken a drastic turn! please help.
in device status is says: Windows has stopped this device because it has reported problems. (Code 43)
location: Port_#0002.Hub_#0005
driver provider: microsoft
date of driver: 21-06-2006
driver version: 6.1.7600.16385
HELP!!!!!!!!!!!

Hi ameet2005,
Please check if the following suggestions help:
First, please disconnect all USB devices and then perform the following steps:
1. Click "Start" button, type “devmgmt.msc” (without quotation marks) in the “Search” bar and press "Enter". Click “Continue”
if necessary.
2. In Device Manager, double click to expand "Universal Serial Bus controllers", right click on the Host Controller, click "Uninstall" and click "OK".
3. Repeat the step 2 to uninstall all items under "Universal Serial Bus controllers".
Then, restart your computer and Windows 7 will reinstall all USB controllers automatically.
If the issue persists, please check if it can be resolved by running
System File Checker.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ”

Can some one help me reinstall my MP640 software on my Imac and macbook pro? as the software does not recognise os 10.7.5

My Imac and macbook pro stopped accessing my MP640 via the home wifi set up, so I sent all the canon software to the trash on both computers, thinking I should reinstall the software I got with the printer, but the software does not recognise os 10.7.5. I am using a netgear modem. I also use time machine to back up to time capsule.

Your Canon Pixma MP640 driver:
http://support.apple.com/kb/DL899

Lightroom 5.7.1, Yosemite OS X - Synchronise Folder function doesn't work in Lr. Is there a compatibility issue? I can see the folders/images in Finder but when trying to synchronise folders in Lr it does not recognise that there are any images and theref

Lightroom 5.7.1, Yosemite OS X - Synchronise Folder function doesn't work in Lr.
Is there a compatibility issue? I can see the folders/images in Finder but when trying to synchronise folders in Lr it does not recognise that there are any images and therefore unable to import to catalogue. Anyone has any idea how to make it work. Thanks a lot.

Hi Elba,
Thank you very much for your reply. Not sure, however, that we are talking about the same problem.
I am trying to perform the same function in Lr that I have been doing for many years in the past and has only been a problem in the last few days (possibly coinciding with upgrading to Yosemite, trying to find out whether that is the problem)
I am not intending to sync any files with Creative Cloud but only trying to use 'Synchronize Folder' function in Lr. Normally, I would right click on a particular folder in Lr catalogue and click on that function to check that the Lr Catalogue is perfectly matching my drives where the original photos are actually stored.
The problem that I only started to encounter is that I can see the files on the actual drives but they do not appear in my Lr Catalogue and they are completely invisible to Lr. I simply can not get Lr to recognise them and then import them to catalogue.
If for example, I export images to Ps and then save and close them, they do appear on my drive but are invisible to Lr and I can't get them imported into the catalogue. Import to folder also not producing any results as they are still invisible to Lr.
Completely baffled by it. Any idea what could be the reason?
Kind regards,
Nik

Itunes does not recognise CDs................please help

i've had my ipod for a few months now and it hasnt been a problem before as it has always imported CDs fine onto my ipod but recently whenever i insert a CD into the drive itunes does not recognise that i have put a CD in and it cant be the CDs that i put in as i have leant one of them to my friend and she said its worked fine on her itunes, when i insert the CD and go onto run CD diagnostics this comes up,
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
FUJITSU SIEMENS P5SD1-FM2
iTunes 6.0.4.2
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.2
UpperFilters: GEARAspiWDM (2.0.4.3),
Video Driver: NVIDIA GeForce 6200SE TurboCache(TM)\GeForce 6200SE TurboCache(TM)
IDE\DiskST3160023AS____________________________3.00___, Bus Type ATA, Bus Address [0,0]
IDE\CdRomHL-DT-STDVDRRW_GWA-4164B_______________1.03___, Bus Type ATA, Bus Address [0,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
Current user is administrator.
D: HL-DT-ST DVDRRW GWA-4164B, Rev 1.03
Drive is empty.
The last failed audio CD burn had error code -128(0xffffff80). It happened on drive D: HL-DT-ST DVDRRW GWA-4164B on -128(0xffffff80) media at speed 0X.
i dont even understand what this means, please help!!!!!!!!!!!! thanx xxxx

Well the report just tells basics of your setup and errors going on in short. Error -128 means either you or iTUnes cancelled the burn before it even started.
Your issue tho is you have no lower filter. you should have 2, and upper filter and a lower filter. Now Im not that good with the filter thing just yet, but I think if you reinstall itunes it will install the lower filter you need.
You will want to remove itunes AND quicktime in the control panel>Add/remove. Dis able any antivirus/security programs so they do not interferr with iTUnes and then download and install the latest iTunes from www.apple.com

6500slide does not recognise bluetooth headsets

i am having a nokia 6500 slide model. it does not recognise bluetooth headsets. i tried with samsung and motorola bluetooth headsets. i tried bluetooth->search audio enhancement menu. have any one experienced same? does 6500s work with only nokia accessories?
- Jayaraman

I have the same problem withe Kensington dongle. Here're the driver details:
Broadcom
6/7/2006
5.1.0.1700
I can transfer files back and and forth using OBEX FTP, no problem, but PC Suite can't find the stack:
Operating system:
Microsoft Windows XP
Build 2600
Service Pack 2
Language: English
Language for non-Unicode programs: English
Locale: English
Input language: English
Nokia PC Suite:
Version 6.83.14.1
Language: English
Connectivity Cable Drivers:
Version 6.83.9.0
PC Connectivity Solution:
Version 7.7.10.0
Microsoft Outlook:
Version 12.0
Build 1014
No supported Bluetooth stack found
I'm using the drive that came with the dongle. I also have a Microsoft Bus Enumerator listed, is that a problem?
Any help is most appreciated!
There's someone in my head, but it's not me
-- P. Floyd

Itunes does not recognise the ipod after update to itunes 8.2.0.23

Hi, Now find, after putting new songs in my play list, that when I plug in ipod to update songs on ipod itunes does not recognise the ipod.
The version of iTunes I updated to was 8.2.0.23 - everything worked fine until then. I see there is a newer version 8.2.1 now available - do you think by installing this the "unable to recognise" problem would be fixed???
Thanks for your thoughts!

I have a similar problem with the iPhone. Tried everything you can think of and then some. There is apparently some devastating bug 7.6 introduced into normal USB device recognition. I've been able to force the phone into recovery mode; the boot recovery USB driver does still work. Restoring the phone every time I need to sync is both scary and time-consuming.

Bios does not recognise cr52-m drive

Similar Messages

Maybe you are looking for