Bios "pcie 3 support" setting is not working?

Hi All,
When I dissable pcie 3 support in bios, it does not seem to turn it off.
I just got this mobo (z77 mpower) with a 3770k and I am having issues with my two Gigabyte 670 in sli (they seems to run fine not in sli). These same cards were fine in my other computer which is a Z68 mobo and 2600k.
I did some reading on a number of forums and there seems to be an issue with many of the Gigabyte 670 cards runing on pcie 3.0. A known fix is to turn off pcie 3.0 in the mobo bios and have them run in pcie 2.0. This sounds right since I was not having any issues on my z68/2600k pcie 2.0 setup. The crappy thing is if you have a mobo that does not have the option to turn of pcie 3 support in the bios... you are screwed and stuck with having ussues.
So my problem is... when is dissable PCIe 3.0 support in the z77 mpower bios and in win7, it still shows that my cards are running in pcie 3.0, I have checked in two places both nvidia ctrl panel and also in gpuz and I continue to have the problems with the cards. When I go back into the bios to double check afterwards, it still shows as off.
Has anyone dissabled the pcie 3 support in bios and can confirm that it does infact actually turns it off and makes the the slots pcie 2.0? Any help would be appreciated as I need to somehow make these cards run in pcie 2.0 and not 3.0
Thanks,

Quote from: flobelix on 24-February-13, 05:42:22
What issues are you talking of?
Issues I am having are only happening is sli. I know its not a PCIe slot on the mobo, I ran a single card in each slot without issues. I also know that these two same cards ran in sli for the past 8 months without any issues on my Z68 board, this only started when I put them into the Z77.
Weird thing is, lets say I put card A in top slot and card B into the other slot.... I get random slowdowns , not only in games but also when browsing and even just looking at the desktop. The computer would freeze up (not freeze completely just everything would become bogged down for up to myb 10 seconds.. then gone for two or three then same freezing again again. Benchmarks like 3dmark11 results would be randowm, I ran 5 tests consecutively and they all ranged from 4000 - 14500 (14500 is what the system should be getting)
Now if I switch the cards and put card B into slot A and card A in the other, those same slowdowns and freezes now become complete system lockups... bsod and or video driver crashes (nvidia kerner stops respondong)
I know its not a driver, bio or software issues. I am having same symptoms under old and new bios on both mobo and vod cards. Also tryed many different versions of vod drivers. I have also dissabled on board sound, wifi and bluetooth to rule those out.
Quote from: fulwider8 on 24-February-13, 07:31:54
Not sure if this might be your issues...Would like to know some of your symptoms. But I have a post here on Ix boards. I was having a slight issue with my driver crashing, and not running great in SLI. Not a blue screen or anything like that. I really thought my video cards were defective. Come to find out. I had one stick of ram that was making all the issues happen. My symptoms.... Every-time I ran my cards in sli..it would cause a stop driver error in Nvidia control panel. If I ran the cards without sli or by themselves. no errors. One of the guys here suggested taking ram out and using only the second and 4th dimm. I took out 2 sticks of ram and it cleared right away. Found out that one of the sticks I took out was bad...Not bad enough to stop working..But just enough to cause these issues. Just a thought or a suggestion-check your ram? I would have never thought the ram was causing my problems..
Not sure if I am speaking out of place..But I only own the z77a-gd65...I have owned other z77a boards too. I have only tried to disable the pci-e 3.0 on this board with no issues. Hope you figure it out. Would like to know what is causing your issues. I plan on purchasing this same board in the future.
Thanks for the feedback fulwinder, I thought the same at first and tryed another manufacturers ram and the results did not change:(

Similar Messages

HT5634 The "automatic Install" in the windows support software does not work. I cannot see the USB in Windows to manually start set uo

The "automatic Install" in the windows support software does not work. I cannot see the USB in Windows to manually start set up.
I have downloaded windows support software from Apple 3 time with the same result. Where can I get a clean copy of the Windows support software?

Did you correctly format your usb stick in accordance with the Boot Camp installation instructions? Go here to the Boot Camp System Requirements page, http://support.apple.com/kb/HT5634, look for your computer model/year and download the correct version of Windows Support software.

X-Fi Titanium PCI Express front pannel connection not working

I can not get any signal to or from the front pannel connector of my X-Fi Titanium PCI Express. (The rear jacks are working fine.)
The front header cable from my Antec P-80B worked perfectly with my onboard motherboard sound. Now that I have it connected to my X-Fi I get nothing from the jacks on the front of my case. (The onboard sound is disabled in my BIOS.)? I've double and tripple checked the connection and it is properly keyed and fitted. Is there a step or a setting that I'm missing somewhere to get this working? Can anyone confirm that the front pannel connection is acti've on the X-Fi Titanium PCI Express?

Re: X-Fi Titanium PCI Express front pannel connection not working? I was truly hoping that would help and I wanted to give you some additional hope. I have a coolermaster case, and it has the AC97 jack on the inside with all my other other front panel connectors for hard dri've activity light, reset, and power on. Three inches down from the AC97 jack, the INTEL HD *which works beautifully with the X-FI, only differs by three wires in different locations and the two pinouts configurations match those of the INTEL site identically.
Please tell me what happens as I would like to post a step by step guide for the others here in the forum. You will know when you have successfully adapted the connector because in VISTA and Windows 7, your sound applet in control panel will have a display of the connectors "lit up" when they are successfully connected. Mine shows FP microphone in the applet when its plugged in, and grayed out when its not. Its great for telling if I am connected on the rear of the soundcard of the front.
Best of luck and .......
Message Edited by jmacguire on 07-06-2009 :09 PM

The ringer setting is not working on my iPhone 4s

My iPhone fell into my pond for less than 10 secs. I pulled it out in time to dry it off and shake some of the water out. I made sure the screen was still working and sounds were functioning then I turned it off and left it in a bag or rice for 24 hrs. The next day I took it out and it was working fine. Now suddenly today, the ringer setting is not working. When I go into settings>sounds I press on ringtone and it seems to be working. Speakers are fine and when someone calls I have no problem. I can also hear the ringtones. But when someone txts me or when I get notifications it doesn't have any sound? The alarms don't work and the sounds in apps don't work. When I put the charger in, it doesn't make a sound. It vibrates only except when someone calls me... My headphone jack seems to be working fine because I can hear everything even the text tones and sounds in apps... What should I do? How much will I have to pay to get someone at apple to fix this problem? I'm assuming there is still some moisture in the phone maybe? It was working for a week until today I'm not planing to upgade to the iPhone 5 anytime soon. Btw, the volume buttons do work it's just when I press on it, it doesn't show the bars when you press up or down... it's just blank.

If it's physically stuck it might be best to bring it into the Apple store at George Street Sydney.
Set up an appointment with the Apple store via the website http://www.apple.com/au/support/contact/

Dynamic rooting (User Record) setting is not working in Nakisa OrgChart SP3

Dear All
The Dynamic rooting setting is not working in the Nakisa OrgChart SP3.
It is giving an error message - "Cannot find the root of your orgchart. The orgchart box may have been deleted or incorrectly specified, or no valid org structure can be found for the selected effective date. Please change the root of the chart or select another effective date."
We followed the same steps as given in the Admin guide of SP3 (P.no. 109 - shown below)
In Orgchart --> General Settings:
* Select the Org chart root value source.
User Record: Retrieves the record specified in the next step from the employee data element.
*Do one of the following to define the org chart root:
If User Record was selected in the previous step, select the field containing the ID of the required organizational object in the employee data element from the User record field drop-down list. For example, if you wish to root the org chart at the org unit of the logged-in user, select the field containing the org unit ID. Hence, we have selected the Org unit ID.
Note:
We had enabled single sign-on with logon tickets
Retained the standard settings in Security Settings --> Employee Source
Had provided full authorization to the roles
If we use the "OrgChart Root" option available in 'Orgchart root value source', the org structure gets displayed correctly from the root object defined.
As this is an standard functionality, Kindly guide us in resolving the issue.
Regards
Ravindra

Ravindra.
You don't have to and shouldn't always include the username and password parameters for the SAP Connection string. When you omit them it will use the user's login credentials.
Remember though that:
The SAPRoleMappingConnection will need them included in order to get the details for the user in the first place.
Without the username and password specified in a connection string you can't click the option to test the connection and result in a successful connection. Remember unable to connect does not necessarily equate to wrongly configured.
I've filtered the log file for errors and the following entries were flagged up:
26 Jun 2012 10:00:06 ERROR com.nakisa.Logger - com.nakisa.framework.utility.Files : deleteFile : java.io.IOException: Unable to delete file: E:\usr\sap\D15\J00\j2ee\cluster\apps\Nakisa\OrgChart\servlet_jsp\OrgChart\root\.system\Admin_Config\__000__THY_SAP_Live_RFC_01\AppResources\attr.txt
26 Jun 2012 13:13:52 ERROR com.nakisa.Logger - com.nakisa.framework.utility.Files : deleteFile : java.io.IOException: Unable to delete file: E:\usr\sap\D15\J00\j2ee\cluster\apps\Nakisa\OrgChart\servlet_jsp\OrgChart\root\.system\Admin_Config\__000__THY_SAP_Live_RFC_01\AppResources\attr.txt
26 Jun 2012 13:43:49 ERROR com.nakisa.Logger - java.lang.reflect.InvocationTargetException
26 Jun 2012 13:55:09 ERROR com.nakisa.Logger - com.nakisa.framework.utility.Files : deleteFile : java.io.IOException: Unable to delete file: E:\usr\sap\D15\J00\j2ee\cluster\apps\Nakisa\OrgChart\servlet_jsp\OrgChart\root\.system\Admin_Config\__000__THY_SAP_Live_RFC_01\AppResources\attr.txt
26 Jun 2012 14:32:03 ERROR com.nakisa.Logger - com.nakisa.framework.utility.Files : deleteFile : java.io.IOException: Unable to delete file: E:\usr\sap\D15\J00\j2ee\cluster\apps\Nakisa\OrgChart\servlet_jsp\OrgChart\root\.system\Admin_Config\__000__THY_SAP_Live_RFC_01\AppResources\attr.txt
26 Jun 2012 15:47:44 ERROR com.nakisa.Logger - BAPI_SAP_OTFProcessor_LinkedDataElement : The dataelement ( SAPPositionVacancyDataElement ) is not defined.
26 Jun 2012 15:47:44 ERROR com.nakisa.Logger - BAPI_SAP_OTFProcessor_LinkedDataElement : while trying to invoke the method com.nakisa.framework.data.Command.getType() of an object loaded from local variable 'p_cmd'
26 Jun 2012 15:47:44 ERROR com.nakisa.Logger - com.nakisa.framework.webelement.charting.data.ChartingData : createNodesFromData : Notes Error: NullPointerException
26 Jun 2012 15:47:44 ERROR com.nakisa.Logger - BAPI_SAP_OTFProcessor_LinkedDataElement : The dataelement ( SAPPositionVacancyDataElement ) is not defined.
26 Jun 2012 15:47:44 ERROR com.nakisa.Logger - BAPI_SAP_OTFProcessor_LinkedDataElement : while trying to invoke the method com.nakisa.framework.data.Command.getType() of an object loaded from local variable 'p_cmd'
26 Jun 2012 15:47:44 ERROR com.nakisa.Logger - com.nakisa.framework.webelement.charting.data.ChartingData : createNodesFromData : Notes Error: NullPointerException
26 Jun 2012 15:47:48 ERROR com.nakisa.Logger - com.nakisa.framework.webelement.charting.data.ChartingData : createNodesFromData : Notes Error: NullPointerException
26 Jun 2012 15:47:55 ERROR com.nakisa.Logger - BAPI_SAP_OTFProcessor_LinkedDataElement : The dataelement ( SAPPositionVacancyDataElement ) is not defined.
26 Jun 2012 15:47:55 ERROR com.nakisa.Logger - BAPI_SAP_OTFProcessor_LinkedDataElement : while trying to invoke the method com.nakisa.framework.data.Command.getType() of an object loaded from local variable 'p_cmd'
26 Jun 2012 15:47:55 ERROR com.nakisa.Logger - com.nakisa.framework.webelement.charting.data.ChartingData : createNodesFromData : Notes Error: NullPointerException
At the very least it looks like SAPPositionVacancyDataElement is missing and whilst the other errors around it are unfamiliar I wonder if it might be a good first step to see if you can track down the reference to and existence of this data element? That being said it looks like your last test occurred well over an hour after this (so you may have already resolved it) and resulted in nothing but information messages. If that is the case it might be worth "rolling" your log file or manually trimming it to the right time frame when posting it? Otherwise it can be misleading as people could flag up issues you have already resolved.
So assuming you haven't tried Luke's suggestion (which should only take a couple of minutes to do) I think you should go back and do so right away .
Regards,
Stephen.

How do i make a tab active and make it stay that way always. If i put a website in my home page in order for the tabs to open automatically in that same homepage , this setting is not working, every time I open a tab , a white window appears .

How do i make a tab active and make it stay that way always. If i put a website in my home page in order for the tabs to open automatically in that same homepage , this setting is not working, every time I open a tab , the window appears white .

By default Firefox opens a blank page for a new Tab, there is no setting to change that action without installing an add-on.
New Tab Homepage extension: 
https://addons.mozilla.org/en-US/firefox/addon/777

HT201269 one fine day, my i phone just hangup lost all contact detail. The screen only show a picture depicting cable connection to iTune. I have tried to restore iphone to factory setting but not working . May i know how to proceed to recover lost conta

one fine day yesterday, my i phone just hangup lost all contact detail. The screen only show a picture depicting cable connection to iTune. I have tried to restore iphone to factory setting but not working . May i know how to proceed to recover lost contacts.

I have taken it back to the Apple store genius bar, but they say they don't see anything wrong. Well unless you use it all day and experience the problems when they happen, you wont see anything wrong. But there are lots wrong with it. But this would be the same store as I purchased the phone. And they backed up my old Iphone 4, but were not able to get anything to load back onto my new phone. So, I lost pretty much everything. But over time, some of my contacts have started showing up, although i am still missing over 800 of them.

My HP Support Assistant is not working?

My HP Support Assistant is not working?

Hi,
Try the following
First of all, uninstall your current version of HP Support Assistant by using the Microsoft 'Fixit' on the following link - this is particularly useful in correcting issues that may prevent reinstallation on machines running a 64bit OS.
http://support.microsoft.com/mats/Program_Install_and_Uninstall
When this has completed, restart the PC.
Next download and install the latest version of HP Support Assistant from the page on the link below - the download links are towards the bottom of the page.
http://h18021.www1.hp.com/helpandsupport/hp-support-assistant.html
After the installation, restart the PC again.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

I have PCI-4452-this card does not work with XP. Are there fixs available?

I have the PCI-4452, i fould that when i installed XP on my system, the card does not work. Does this card have any drivers for ir to work on XP. Or do i have to stay on NT.

Hello,
This card is actually supported under XP for use with drivers since 6.9.2 and above (only traditional driver).
Kind Regards
Steven Bird
Applications Engineer
National Instruments

SET/GET not working when I submit one program into Main program.

Hi All,
I am using set/get parameter as follows but somewht it is not working.. Please help.
IF ( uf_instn = 'ACEFR' and uf_messg <> 'BSP' ).
 set parameter id 'AJN' field lf_jobname.
 set parameter id 'AJC' field gf_jobcount.
ENDIF.
SUBMIT zace_interface
 USER sy-uname
 VIA JOB lf_jobname
 NUMBER gf_jobcount
 WITH SELECTION-TABLE lt_seltab
TO SAP-SPOOL
 AND RETURN.
in the zace_interface program I have another submit program
 submit zrsbdcsub and return
 user 'ZACE_INTERFACE'
 with mappe eq lf_group
 with von eq sy-datum
 with bis eq sy-datum
 with fehler eq space
 with logall eq co_true.
ad inside this submit im using
 get parameter id 'AJN' field v_jobname.
 get parameter id 'AJC' field v_jobcount.
but i am not able to get the values into v_jobname & v_jobcount.
Can you please help me in this regard. how i will get the values in v_jobname & v_jobcount.
Thanking you in advance
Regards,
Prashant

Hi..,
any way u r executing the programs in the same session but between diff. internal sessions u can use the IMPORT and EXPORT options ( ABAP MEMORY )
or do one thing...
In the first program Copy these fields into a file in the application server,, and in the Second submit program u retrieve these variable values from the Application server file into these two variables!!
just now i have solved one of the issues of this Kind by using an Application server file.
In the first program..
IF ( uf_instn = 'ACEFR' and uf_messg <> 'BSP' ).
OPEN dataset 'FILE' for output in text mode encoding default.
transfer lf_jobname to 'FILE'.
transfer gf_jobcount to 'FILE'.
CLOSE dataset 'FILE'.
ENDIF.
and instead of using the GET parameters in the second program ..
OPEN dataset 'FILE' for input in text mode encoding default.
read dataset 'FILE' into v_jobname.
read dataset 'FILE' into v_jobcount.
CLOSE dataset 'FILE'.
This has solved my problem !!!!! hope this helps u also!!
regards,
sai ramesh

Why does set font not work in report generation toolkit?

I would like to change font and underline when inserting text into a Microsoft Word document. I have tried using the
"Set Report Font" vi directly in front of an "Append Report Text" vi in my own application. The inserted text at the bookmark is always in the default text mode
of the document. Is this a bug?
I also tried the find and replace vi with the same result. Font will not change.
I also cannot find any examples of this usage that work. See example vi file below.
Save at C:\ or adjust the template location accordingly in the vi.
Can anyone help me out?
Thanks,
Chris
Attachments:
ChassisTestAutomatic (6.1).vi ‏39 KB
TestPlan.dot ‏34 KB

Dhubbell wrote:
That's a cool tool Ben! However, with a bookmark, you know the location on a Word Template, and if you know the location in MS Word, you can then set the fonts you want in Word.
Do you know how to change the fonts in a string?
Example, How do you insert this block of text on a SINGLE MS Word bookmark?
PART NUMBER: 1234567890
DESCRIPTION: These lines are formated dynamically, some orders may have 1 PN, and other orders many have 500 PNs.
I'm formatting my line details and inserting them on a MS Word bookmark. After the initial bookmark I have no more control of the fonts for the entire string block. I'd like to dynamically change the fonts in a string and I'd like to use MS Word. I saw HTML report writing, but, in my particular application, HTML reports will not work.
Doug
I don't have the time to try anything but as a suggestion I would experiment with the range start end properties (e.g. from start =0 to end =
12 bold is true, from 13 to 23 bold is false, ....) You first insert text without formatting then you use the range start and end to format the text.
I'm not sure it will work but it's worth a try.
Ben64
note: I would create a 2D array of start and end index of your string and auto-index a for loop that contain the range property node.

Hp envoy m6 sound card, simmple pass application and support assistant is not working properly

i have hp envoy m61204tx.
after upudate using hp support assistant sound card is not working properly also when i run hp simple pass or hp support assistant only start window appears then it hides nothing happend next.
please guide me what is the problem and how to solve it.
any help will me much appriciated.
Thanks.

@alki,
I understand that sound has quit working after support assistant ran a few updates.
Press Windows Key + X and select device manager. The sound card should be listed in the sound section. What status is displayed for the sound card?
What is the status of the mute key on the notebook? Does it have an amber light?
What happens if you try to install this driver?
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Silverlight 5 binding on a property with logic in its setter does not work as expected when debug is attached

My problem is pretty easy to reproduce.
I created a project from scratch with a view model.
As you can see in the setter of "Age" property I have a simple logic.
public class MainViewModel : INotifyPropertyChanged
public event PropertyChangedEventHandler PropertyChanged;
private int age;
public int Age
get
return age;
set
/*Age has to be over 18* - a simple condition in the setter*/
age = value;
if(age <= 18)
age = 18;
OnPropertyChanged("Age");
public MainViewModel(int age)
this.Age = age;
private void OnPropertyChanged(string propertyName)
if (this.PropertyChanged != null)
PropertyChanged(this, new PropertyChangedEventArgs(propertyName));
In the MainPage.xaml
<Grid x:Name="LayoutRoot" Background="White">
<TextBox
Text="{Binding Path=Age, Mode=TwoWay}"
HorizontalAlignment="Left"
Width="100"
Height="25"/>
<TextBlock
Text="{Binding Path=Age, Mode=OneWay}"
HorizontalAlignment="Right"
Width="100"
Height="25"/>
</Grid>
And MainPage.xaml.cs I simply instantiate the view model and set it as a DataContext.
public partial class MainPage : UserControl
private MainViewModel mvm;
public MainPage()
InitializeComponent();
mvm = new MainViewModel(20);
this.DataContext = mvm;
I expect that this code will limit set the Age to 18 if the value entered in the TextBox is lower than 18.
Scenario: Insert into TextBox the value "5" and press tab (for the binding the take effect, TextBox needs to lose the focus)
Case 1: Debugger is attached =>
TextBox value will be "5" and TextBlock value will be "18" as expected. - WRONG
Case 2: Debugger is NOT attached =>
TextBox value will be "18" and TextBlock value will be "18" - CORRECT
It seems that when debugger is attached the binding does not work as expected on the object that triggered the update of the property value. This happens only if the property to which we are binding has some logic into the setter or getter.
Has something changed in SL5 and logic in setters is not allowed anymore?
Configuration:
VisualStudio 2010 SP1
SL 5 Tools 5.1.30214.0
SL5 sdk 5.0.61118.0
IE 10
Thanks!

Inputting the value and changing it straight away is relatively rare.
Very few people are now using Silverlight because it's kind of deprecated...
This is why nobody has reported this.
I certainly never noticed this problem and I have a number of live Silverlight systems out there.
Some of which are huge.
If you want a "fix":
private void OnPropertyChanged(string propertyName)
if (this.PropertyChanged != null)
//PropertyChanged(this, new PropertyChangedEventArgs(propertyName));
Storyboard sb = new Storyboard();
sb.Duration = new Duration(new TimeSpan(0, 0, 0, 0, 100));
sb.Completed += delegate
PropertyChanged(this, new PropertyChangedEventArgs(propertyName));
sb.Begin();
The fact this works is interesting because (I think ) it means the textbox can't be updated at the point the propertychanged is raised.
Please don't forget to upvote posts which you like and mark those which answer your question.
My latest Technet article - Dynamic XAML

My iphone 4s setting is not working i can,t access it, what should i do.

my iphone 4s settings is not working.I hold home +power button for 15sec to solve this problem but it didn,t work,now what should i do.I am confused what to do b/c if i can,t access to my phone setting how could i oprate it.Plzzz do something for me thnx.Faisal.

need more information, when you say not working, is it frozen, is it powered off and not comming on, "NOT WORKING" is not going to help us help you.

Standard Enhanced PCI to USB host Controller not working

Plz help me its suck i can't find any driver for this USB port its suck all my usb ports are not working they not accepting any usb or some thing or intel managment interface also not working plz help me . Thankyou
Us Device PCI
Device PCI\VEN_8086&DEV_1E26&SUBSYS_17F8103C&REV_04\3&11583659&0&E8 was configured.
Driver Name: usbport.inf
Class GUID: {36FC9E60-C465-11CF-8056-444553540000}
Driver Date: 06/21/2006
Driver Version: 6.2.9200.16384
Driver Provider: Microsoft
Driver Section: EHCI.Dev.NT
Driver Rank: 0xFF2005
Matching Device ID: PCI\CC_0C0320
Outranked Drivers:
Device Updated: false
Intel Mangagment interface
Device PCI
Device PCI\VEN_8086&DEV_1E3A&SUBSYS_17F8103C&REV_04\3&11583659&0&B0 was configured.
Driver Name: null
Class GUID: {00000000-0000-0000-0000-000000000000}
Driver Date:
Driver Version:
Driver Provider:
Driver Section:
Driver Rank: 0x0
Matching Device ID:
Outranked Drivers:
Device Updated: false

What is the installed operating system?
In which region of the world are you located?
Try the following Intel Management Engine software
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-113870-1&cc=us&dlc=en&lc=en...
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Bios "pcie 3 support" setting is not working?

Similar Messages

Maybe you are looking for