BIOS Problem with 915P Combo

Hi there...
I have one MB 915P Combo and i have problems in BIOS configuration.
I go to: Advanced BIOS Features / BOOT SEQUENCE
And have one option Boot from other Device, it have No.
I change to Yes, and reboot and now it is possible to use pen disks.
The problem:
If i install a program and at the end of installation (for example update IDE/Raid utility) it is necessary to reboot windows , i restart the windows and when go to windows, now is not possible to use pen disks...
To solve the problem temporaly:
It is necessary to go to the BIOS configuration and Change the Boot from other device to "No" and reboot... and Change again to "Yes" to work with Pen disk.
And sometimes appears a blue window in Windows with a Device Driver error.
How to solve the problem ?
I have the latest BIOS 1.6
Thanks.

What if you just normally reboot windows without any new installation? Does it happen the same way?

Similar Messages

Problem with 915P Combo

i have 915P Combo motherboard it always power on automatically while the ethernet cable is pluged.
so how can i avoid this?
it seems like wake up on lan
how can i stop this

ok where can i found this option in bois i search alot on it but i didn't find it please help me to avoid this

A few bios problems with my 915p Neo2 platinum board

I'm wondering af anyone here can help me.
I just got a new system and a friend of mine helped set up the bios for me, afterwards he failed to tell me how he had configured the bios (my first big mistake).
Since the buidling of the system there have been 3 short beeps at the beginning of startup. I was told that it was a warning system of some sort and when i looked it up, the informations pointed towards a problem with the RAM.
I ran memtest86 and it found no problems with the RAM, so i contacted the site i bought the parts from and they suggested i reset the bios.
I did so and the beeps remained, but my DVD and DVD-writer drives arent being detected anymore.
I took my PC around to another friends house with only his keyboard and monitor connected. The beeping had stopped before we changed anything. Bringing it back around to my house resulted in the beeping returning.
From this i gathered that the only things different may have been his power source and the peripherals i have attached to the back of the case. (speakers, printer, kb/m, etc)
Going by the manual map, my 2 HDDs are connected as slave/master in IDE port 1 and my two DVD drives are connected to the yellow IDE port that is closest to IDE port 1 (it's either IDE 2 or 3, the map isnt too clear on which is which).
Long story short, can anyone help me in identifying the source of the beeps and their meaning, an optimum setup for my bios and how to get my DVD drives to work.
Thanks in advance to anyone who can help me. I'm fairly new to building computers and my friends are the type to suddenly become unavailable as soon as a problem arises.
edit: just noticed i missed the spec description part menitoned in the rules.
MSI s775 915P-Neo2-Platinum
Version 1.4 of bios
Pentium 4 540 LGA775 3.2GHz
Corsair VS 1GB DDR2 240 pin RAM
256 MSI PCI-express GF6800GT, latest drivers
600W 3XS-EzCool PPFC
Western digital WDC WD1600JB-00EVA0 (160GB) (master)
Seagate U series 5 HDD ST340823A (40GB) (slave) Both on IDE slot 1
Liteon DVD-ROM (spec unavailable)
MSI 4x DVD-RW +/- (part no: G57-CB00243, this is all i could find on this part form the box)
Sound Blaster Audigy
Windows XP SP2
second attempt at clearing up the garbled mess from above.
Motherboard is making 3 short beeps on startup. Indication of a problem with memory. I've established that it's something external that causing the beeps as the memory has checked out fine with memtest86. Hence i will be checking all the attached devices.
I was guided to reset the bios in an attempt to clear up this problem above. Doing so has resulted in my bios being unable to detect my DVD drives.
My DVD-drives are connected to IDE port 2/3 (manual is unclear on which is which).
Everything was in working order (with the exception of the beeping) before the bios was reset but due to my lack of knowledge/involvement with the original configuration of the bios, i'm at a loss as to how to fix it.
If anyone could recommend me any updates for the bios, or could advise me on how to configure my bios accordingly to the parts i have i would be most appreciative. Also, if osmeone would be abel to shed some light on the beeping issue i would be thankful also.

Quote
Originally posted by Danny
The board uses a Via raid controller for the IDE 2 and 3 channels, and you do have that enabled.
Under SATA devices configuration you should select Enhanced instead of compatible. But this should effect your problem.
I see there is a 1.5 bios released that mentions the via controller
http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=601&kind=1
Maybe someone with this board will pitch in and help.
I saw this and was wondering if i should install it. It would be the equivelent of resetting the bios again wouldnt it? So it wouldnt be that much of a step back from where i am at the moment and it might be able to sort my IDE problems.

Performance and bios problems with K8T

Hi, I recently installed a new graphics card (6800 LE) but when I went to benchmark it the scores were way down, 6377 in 3dmark 03 and 28,421 in Aquamark, and that was after I had installed the latest bios and mobo drivers from MSI, unlocked the cards pipelines to 16 and shaders to 6, installed the latest XG Nvidia drivers (80.40 ) and checked about everything else I could think of.
I looked at RivaTuner and in the Northbridge info it said AGP status - disabled and in the Display Adaptor info, AGP status - disabled. In the bios the setting for AGP is greyed out ( or blued out ) so I am unable to set it to 8X or even check what it is set for.
Just to add the icing on the cake I now find that I can't get into bios with my existing keyboard as it's a USB model. I refitted my old ps2 keyboard and got into bios where I enabled the setting for legacy devices but there was no setting for usb 1.1 port 64/60 Emulation as listed in the manua.
Any assistance on any of these problems would be gratefully received. Tal

I reloaded the 4 in 1 drivers and the XG 80.40 graphics drivers and my bechmarks soared. Thank a lot Tiresmoke.

Problem with editable combo box and creating dynamic table values using js

Hai
I have used jquery.jec.js to make my dropdown list as editable... I need to create dynamic table values on the onChange event of dropdown using javascript.
Now am facing the problem in it...
I am getting duplicate rows in the table... think(assumption) this jquery.jec.js is calling the dropdown again creating duplicate values...
Please help me out.... Any help is appreciable... Thanks in advance

Thanks elOpalo, for your valuable response....
I have found the correct way of doing.
Before i had my code like this,
<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=ISO-8859-1">
<title>test</title>
<script type="text/javascript" src="js/jquery-latest.js"></script>
<script type="text/javascript" src="js/jquery.jec.js"></script>
<script type="text/javascript">
$(function(){
$('#list').jec();
function giveAlert(){
alert('hello');
</script>
</head>
<body>
<form>
Combo Box:
<select id="list" name="list" onChange="giveAlert();">
<option value="1">one</option>
<option value="2">two</option>
</select>
</form>
</body>
</html>
Now i have changed as the following,
<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=ISO-8859-1">
<title>test</title>
<script type="text/javascript" src="js/jquery-latest.js"></script>
<script type="text/javascript" src="js/jquery.jec.js"></script>
<script type="text/javascript">
$(function(){
$('select.combo').jec();
$('select.combo')
.change(function() {
alert($(this).val());
}).change();
</script>
</head>
<body>
<form>
<table>
<tr>
<td>Combo Box:</td>
<td><select class="combo"><option value="b">banana</option><option value="a">apple</option></select></td>
</tr>
</table>
</form>
</body>
</html>
The problem is with the function i have called on the onChange Event.. Now i have defined it inside the jquery function of dropdown to make it as editable...

Problem with insignia combo TV/DVD

http://www.consumeraffairs.com/home_electronics/insignia.html
I have the same problem ... 2 and 1/2 years after purchase.
also told it was the 2 year Insignia warranty + 1 year from Best Buy
so.... do I take it back or ???

Thanks for the quick reply ... guess I should have ready how unhappy most people
were with the DVD portion:
http://reviews.bestbuy.com/3545/9789734/insignia-32-class-1080p-60hz-lcd-hdtv-blu-ray-disc-combo-rev...

BIOS problem with m2n61-ar Acacia

Hi, I have recently updated my CPU, but I can use it, motherboard throws "error CPU not supported", I have installed the last BIOS update but i still having this problem, could you send me a BIOS update for amd 6000+?
Thanks

Hi,
Welcome to the HP Forum!
thongil wrote:
Hi, I have recently updated my CPU, but I can use it, motherboard throws "error CPU not supported", I have installed the last BIOS update but i still having this problem, could you send me a BIOS update for amd 6000+?
Thanks
The following CPU's are the only supported processors for your motherboard. Please identify your "amd 6000+" with its complete AMD designation, including family and wattage.
Athlon 64 X2 with Dual Core technology up to 65 Watt
Athlon 64 up to 65 Watt
Sempron up to 65 Watt
Athlon 64 X2 with Dual Core technology up to 65 Watt
Athlon 64 up to 65 Watt
Sempron up to 65 Watt
regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

BIOS problems with 7030 - powering off?

I just tried to flash the new 2.1 BIOS for Neo Platinum and it failed with a checksum error in the windows flash program.
I made a boot disk with the award flash and the 2.1 / 1.9 binary and autoexec.bat as per bios rescue instructions. The disk boots on another machine but on the broken one it reads the first 5 spins and then powers off. There are no beeps and I tried disconnecting all USB / IDE / SATA cables.
If I unplug the floppy drive it beeps, complains about no floppy then powers off.
If I don't put the floppy disk in the drive - it boots, complains about no system disk then powers off.
I tried resetting the CMOS with the cable unplugged but I still get the same problem.
The only component left to remove is my Nvidia 6800 (AGP).
Messages on the screen:
Award Bootblock Bios v1.0
BIOS ROM CHECKSUM ERROR
Detecting floppy drive A media
Drive media is 1.44... [wait about 2 seconds - powers off]
Can anyone explain why it is powering off and how I could fix this?
Thanks,
Graham

Thanks Kwea for giving me some hope!
I just found this thread:
https://forum-en.msi.com/index.php?topic=89737.0
I will try this evening with the memory and AGP card removed. Fingers crossed...

BIOS problems with K8T Neo2

K8T Neo2, AMD64 3400, 2x 512 3200 DDR (slots 1 & 3), PNY nVidia Quadro FX500, WD Caviar 60GB.
The system will not boot (cold or warm) without first clearing the BIOS via the JBAT. If I try to restart the system, the LED panel shows four red (processor error). If I clear the CMOS, it will post then say that there was an error in the BIOS. It will then ask if I want to enter the setup (F1) or load defaults and continue (F2). If I go into the setup, make any changes (even just the date and time) and restart the system, it won't post until I clear the CMOS again.
The owner is getting fed up and is threatening to go buy a Dell, so any help would be very much appreciated!!!
- Justin

Pete,
Quote from: Pete67890 on 16-March-05, 07:53:07
Not sure how good the beta version is, after flashing I am unable to get the system to post.
Have you tried bootblock-programming, as described somewhere on MSI website? FDD is needed for that.
Quote
Talked with MSI and they are sending me another board and instructed me to re-flash with the same file (3.34). Apparently it resolves an issue with endusers using an AMD 64 3400+ chip
This is a CPU that is intended to be sold to OEMs like HP/Medion only. It runs only with 600MHz HTT. Maybe you should ask your dealer to replace that with a retail CPU, e.g. 3200+ with Winchester Core.
Quote
and more importantly (see my thread) will fix my problem of not being able to save CMOS settings.
That might be a problem related to the "wrong" CPU, IMHO.
Quote
*One other note, MSI said that I need to change the front side bus to 800 for these processors not 1000 as the default would have it.... If its not changed the system wont post.
Indeed - had you been able to enter BIOS setup previously? If yes, then try flashing BIOS 3.30 using the Boot Block method and set your HTT to 800. Maybe then you will be able to save your BIOS settings.
Quote
If you still want the file, I could send it to you, but use it at your own risk..just post your email.
I am still interested, just use the "PM"-or Mail-button on the left. Thanks in advance.
Greets,
Michael

Problems with a combo box in dynpro

Hi guys, im creating a combo box in a dynpro, but is not showing anything.
the code is the following:
AT the screen painter..
MODULE USER_COMMAND_0100.
   PROCESS ON VALUE-REQUEST.
FIELD TI_COMBO MODULE create_dropdown_box.
*then the module in the main program.....
module create_dropdown_box input.
TYPES: BEGIN OF type_carrid,
         op1(20),
         ID TYPE N,
       END OF type_carrid.
DATA ti_combo TYPE STANDARD TABLE OF type_carrid WITH HEADER LINE.
ti_combo-op1 = 'Not processed'.
TI_COMBO-ID = 1.
append ti_combo.
ti_combo-op1 = 'Duplicated.
append ti_combo.
ti_combo-op1 = 'For Payroll'.
append ti_combo.
CALL FUNCTION 'F4IF_INT_TABLE_VALUE_REQUEST'
       EXPORTING
        RETFIELD = 'ID'
        DYNPPROG = SY-REPID
        DYNPNR = '100'
        DYNPROFIELD = 'TI_COMBO'
        VALUE_ORG = 'S'
       TABLES
            value_tab       = ti_combo
       EXCEPTIONS
            parameter_error = 1
            no_values_found = 2
            OTHERS          = 3.
IF sy-subrc <> 0.
ENDIF.
endmodule.
Edited by: javier santana on May 7, 2008 5:47 PM

Hi,
Check the below code.
TYPE-POOLS: VRM.
DATA:V_NUM TYPE I.
DATA:NAME TYPE VRM_ID,
     LIST TYPE VRM_VALUES,
     VALUE LIKE LINE OF LIST.
DATA:I_WORKPATTERN LIKE ZWORKPAT OCCURS 0 WITH HEADER LINE.
DATA:ZPATTXT(60).
MODULE WORKPATTERN_LISTBOX OUTPUT.
NAME = 'P9434-ZWORKPATTERN'.
    IF V_NUM IS INITIAL.
    CLEAR I_WORKPATTERN.
    REFRESH I_WORKPATTERN.
    SELECT *
           FROM ZWORKPAT
           INTO TABLE I_WORKPATTERN.
    IF NOT I_WORKPATTERN[] IS INITIAL.
      LOOP AT I_WORKPATTERN.
        VALUE-KEY = I_WORKPATTERN-ZWORKPATTERN.
        VALUE-TEXT = I_WORKPATTERN-ZWORKPATTERN.
        APPEND VALUE TO LIST.
      ENDLOOP.
    ENDIF.
    CALL FUNCTION 'VRM_SET_VALUES'
      EXPORTING
        ID                    = NAME
        VALUES                = LIST
     EXCEPTIONS
       ID_ILLEGAL_NAME       = 1
       OTHERS                = 2.
    IF SY-SUBRC <> 0.
      CLEAR SY-SUBRC.
    ENDIF.
    V_NUM = V_NUM + 1.
    ENDIF.

BIOS Problems with NEO 875 FISR2

I have a NEO 875 FISR2 motherboard I am trying to install. At initial bootup a line comes up saying "BIOS not installed". Of course windows XP will not boot up if their is no bios but a screen will come up saying that windows has noticed hardware changes and asks if i want to start the computer normally or in safe mode. When i press delete and enter the AMI bios screen I set it to normal low performance factory defaults through the default bios settings button. I save and exit but still no luck, windows still asks if i want to start in safe mode and auto reboots when it cannot start windows whereupon the same message "BIOS not installed" pops up again. I've tried everything I can think of with no luck. the mobo didnt come with a BIOS reinstall disk either. Thanks in advance for any help on this topic.

:wall:YEP; TRY TO REPAIR I know it stinks, but this USUALLY HAPPENS when installing such a critical componant like a MO-BO. That is why it is recomended to do a clean install when swapping a MO-BO..Sean REILLY875

Bios Problems with S10e and 14cn97ww

I updated my s10e to the new Bios version 14cn97ww (through the automatic update service from lenovo thinkvantage). Now i can´t access my Bios anymore by pressing F2 or in fact any other button during start up.
I can´t access system recovery too for that matter and splashtop doesn´t boot either (but it is activated in the lenovo quick start tool).
Windows XP boots fine and still works, but it bothers me that i can´t access Bios and Splashtop anymore. Is there any help for that problem ? I tried changing the Ram, tried removing the battery and pressing the power button and tried to downgrade the Bios which sadly didn´t work.
Please help.
Thanks in advance.
Solved!
Go to Solution.

Hi
The latest BIOS for MY S10e 4068 46G is 14CN67WW - according to:
http://consumerdl.lenovo.com.cn/UserFiles/Driver/en/Downloads and Drivers/S9eS10e/14cn67ww.txt
Versions Rev. Issue Date
14CN67WW 01 2009/05/14
14CN66WW 01 2009/04/17
14CN57WW 01 2009/04/07
14CN51WW 01 2008/11/20
14CN47WW Initial release
http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-72740
Versions Rev. Issue Date
14CNA0ww 01 2010/10/22
14CN98ww 01 2010/07/20
14CN97ww 01 2010/03/19
14CN96ww 01 2009/11/13
14CN95ww 01 2009/09/21
14CN94ww 01 2009/07/06
14CN88ww Manufacturing Initial
14CN96ww or higher seem to be made for S10e 4068 as well - search for other KalvinKlein forum entries
Support models IdeaPad S9e/S10e, S10 wiht 3G (4329, 4333)
Version 14CN96ww

BIOS Problems With CD\DVD Rom Drive. Not a Filter Problem

My Hp Laptop Was Messed up for a while with ramdom 2 sec restarts so i had a tech guy that i know and it was fixed. sadly after a few weeks my CD\DVD Rom drive quit working and was not (and still is) registered in Bios. i reset the BIOS Back to factory settings and had some luck. i worked fine but then when i woke up the next day i was gone again. i does do this often but im getting quite annoyed.. can someone help me with this issue.

Well, I now have the same symptoms as described in this discussion group. I'd put the CD in the superdrive for iTunes to burn, the computer accepts it, makes it's whirring noise (louder than a couple days ago), nothing comes on screen that says its able to read it, and around a minute or two it ejects the CD.
These larger 24inch iMacs are NOT the easiest to lug over to the Apple store, especially if taking mass transit! I have not found any solutions described here that works ...short of apple support.
I am a rather tidy and tech savvy person. No dirty CDs, no warped CDs, no inappropriate force to the drive, etc. Based on the number of similar postings, HAS APPLE ACKNOWLEDGED THIS AS A DRIVE DEFECT YET?

Problem with installation 10.5.4 Combo

Hello everyone,
I'm trying to update my Powerbook from 10.5 to 10.5.4. I downloaded the Mac OS X Update Combo 10.5.4. Then it asked me to restart but during the installation, it stucked at "Configuring Installation". Did also run DU and repair HD, permissions. All fine. What should I do now?
Thank you

My MacBook did exactly the same thing. I did notice that Software Update said it was a 59 MB file and what I downloaded was only 57.7 MB.
I'm going to download the combo file, http://www.apple.com/downloads/macosx/apple/macosx_updates/macosx1054comboupdate .html , when I get to a high speed connection. I've never had a problem with the combo updates.

FYI: MS-7125 BIOS has problem with Hard Drives withNative Command Queuing (NCQ)

For those the have messed my two treads on which both ended up being cause by K8N Neo4 BIOS problem with HD's with NCQ.
Will wonders never cease? MSI Support finally conceded the BIOS has a problem with Hard Drives with NCQ and they have forwarded the problem to their programming department.
However, do not look for any results for above two weeks.
Roger

The problem that this thread has been trying to follow is the incapability of the nVidia RAID Controller with Serial ATA Type 2.5 drives. I know the threads has been hard to follow and part of that is because when I started the thread I had what appeared to be three totally un related problems, but all three were traced down the common problem of the incapability of RAID Controller with Serial ATA Type 2.5 drives.
The title of this thread is MS-7125 BIOS has problem with Hard Drives with Native Command Queuing(NCQ). The statement was true at the time it was written and has nothing to do with memory problems.
Sense the thread was started MSI has fixed the BIOS part of the problem, but we have sense learned the nVidia RAID Controller Command software and its driver has problems too. I have been working MSI Support, they have been using me to test pre-beta BIOS and Drivers soon. Of the testing I have done the pre-beta BIOS worked and the Pre-beta 32-bit driver works. I am assuming that the latest BIOS V1.B had as part of it included fixes was the needed fixes for working with the nVidia RAID Controller as I have test the pre-beta RAID Driver with BIOS Version V1.B as the Raid array function fine windows XP Pro 32-bit Edition. As I have had no communications with MSI support of over a week now I am hoping for a release of 32-bit and 64-bit RAID Drivers. But, nobody should get the hopes up, because through other backdoor sources nVidia is having a hell of a time. One reason for this I heard is that the nVidia RAID Controller is fully software, no hardware other than the electrical drive interfaces. Their problem started when they tried using the old 32-bit code Controller with new 64-bit hardware drivers and now they are having to totally rewrite the controller core in 64-bit code. But, knowing my source, it may all be fiction.
The RAID Array you say is up and running, are the drives full specification SATA 2.5 in other words do the both have 3Gb/s speed and NCQ. If you send me the full part numbers I will check the specifications a get back to you. Because if you have nVidia RAID 0 Array you working you will be the first to have done it and there about 230 people around the world that would like to know how you did it, even MSI, who's pre-beta nVidia RAID Drivers that will work with BIOS V1.B for 32-bit Windows only and nothing for Windows XP 64, would like to know.
Roger

BIOS Problem with 915P Combo

Similar Messages

Maybe you are looking for