BIOS Request for 2 R9 280X, One PCB V1.0, another PCB V1.2 (BF4 edition)
Hi there, I have flashed both my cards to the 015.040.000.000.003435 (113-3865000-X77) BIOS that is found on tomshardware.
However, whilst my original card came with an older BIOS than this, my new card came with a newer version. (These will be shown below)
Whilst my cards have both been working fine, I have noticed that my PCB V1.2 card has a strange "voltage lock". Every piece of monitoring software I have tried to use says the voltage is always 1.2, or 0.950 based on load levels. These are the values that are inside the X77 BIOS when inspected with VBE. However, in MSI afterburner, the voltage is displayed as a different value. After having checked allow voltage control and monitoring in MSI AB. My voltage is not shown as a number, but rather a + and - modifier, much like PowerTune is. This modifier does work, after having played around, I have figured out that each integer in this modifier is in fact a single mV (or around that). MSI AB then displays my new card's voltage as a varying number, whereas my old card is shown as a flat line. As shown here
I have no idea where MSI AB is getting this "pseudo-voltage" value from, since both HWiNFO and GPU-Z both report that it is always 1.2v when under any load. However, it worth noting that this value, whilst I do not believe it is the typical VDDC value, does in fact have some impact on the card's voltage, as I have tried running benchmarks with this card, and with a lower voltage according to MSI AB the card does indeed run cooler.
I have also noted that HWiNFO does in fact, show that the new card is missing a whole load of sensors, labelled as "ChiL/IR PMBus" as seen here. I can only assume that this particular sensor module was removed from later PCB's, or that this card is faulty?
Please note. I have only experienced unlocked voltage control on both my old and new card whilst using the X77 BIOS.
If I use the BIOS that comes with the card, which for my old one is:
And for my new one is this:
Then I am unable to modify either the "pseudo-voltage" found on card 1, or the voltage found on card 2, regardless of MSI AB options.
The reason I am still running the X77 BIOS is that I want the ability to modify voltage, as it very important to me.
My S/N's are
PCB V1.0 card: 602-V277-19SB1309097475
PCB V1.2 (BF4) card: 602-V277-28SB1311072756
The PCB revision numbers (1.0 and 1.2) I have gotten from the bottom of the PCB, right next to the PCI Express connector. However I have not inspected the PCB to actually confirm they are different, and this maybe just be an identifier.
Hey there, the 330 BIOS is the exact same as the one my second card came with when I purchased it (same MD5 hash), I have flashed the 302 BIOS to my old card and switched my BIOS on the second card back to stock and now I cannot change voltages in afterburner. Are these cards by any chance voltage locked by design and the X77 BIOS enables voltage changes?
Since I need the ability to change my cards voltage I have since switched back to the X77 BIOS until I can resolve this issue. Thank you.
Similar Messages
-
"Legacy Mode" BIOS request for MSI R9 280X GAMING 6G
"Legacy Mode" BIOS request for MSI R9 280X GAMING 6G
S/N: 602-V277-310B1407096530
Installed BIOS: TV277MS.3A0
Hi,
I have the annoying problem with my new video card: a screen is periodically blinking in 2D. Probably that problem already solved in a newest BIOS?
I have to use "Legacy" mode because of my PC does not start otherwise.
Related hardware: MB: MSI P67A-GD65 B3 (BIOS 1.19), CPU: i7-2600K, Monitor: HP ZR2440w (DP connection).
Thank you.here is .3A1
TV277MS.3A1 legacy
TV277MH.3A1 uefi
flash guide:
Quote
Decompress the attached .rar archive with Winrar: http://www.rarlab.com/download.htm
Create a bootable usb stick (https://forum-en.msi.com/index.php?topic=165175.0).
Then unpack the previously provided archive (xxx.rar) and put the included file (TVxxxxx.zzz) on that stick.
Rename TVxxxxx.zzz to zzz.rom.
Put the atiflash.exe from: https://www.techpowerup.com/downloads/2306/atiflash-4-17/
on the USB stick too. Now boot from the stick.
Type atiflash -p -f -noaper 0 zzz.rom [ENTER] and let it flash the vbios. -
UEFI/GOP BIOS Request for MSI R9 280X Gaming OC Edition
Requesting a UEFI/GOP Bios update for my R9 280x Gaming.
S/N: 602-V277-19SB1309119942
BIOS Pic:
Thanksthe card should have dual BIOS chips,
turn off your computer, then switch it to second BIOS chip
and check if will be GOP compatible -
UEFI bios request for N780 TF 3GD5/OC
UEFI bios request for N780 TF 3GD5/OC
S/N: 602-V298-010B1308089788
ROM: 80.10.37.00.15 (P2083-0020)Quote from: Marski69 on 14-May-14, 01:44:02
Hi Svet
Any chance that my Bios is the same?
And i can use it?
Can i post my Bios.rom?
Tnx for reply!
Em, we don't have a second sight... You need to at least supply some info on your card namely S/N and a copy of your vbios saved to file (that you uploaded to some file hoster and added link here). -
GOP / UEFI BIOS request for MSI 280X
S/N:602-V277-250B1407011905
http://www.filedropper.com/tahiti_2
i would like you to make if you can a board power settings managment + 150 and Voltage increase unlock or just unlocked voltage , Fan settings min 30 max 100
thank you . I know u allready gave me one bios but could you modify this one pls .thank you guys ,
-
GOP /UEFI bios request for GTX N770 TF 2GD5/OC
Symptoms: System will not POST after ASUS Z9PE-D8 WD mobo update to latest BIOS. Worked fine previous. System will POST and run fine with other graphics cards.
The card will POST and run fine in ASUS MAXIMUS V GENE mobo with not current bios. With which I have pulled GPU-Z info as required for a BIOS request.
Prompt response greatly appreciated! There is work I need to be doing! Thank you so much.
S/N: 602-v282-220B1308092571
NVIDIA Firmware Update Utility (Version 5.141)
Adapter: GeForce GTX 770 (10DE,1184,1462,2825) H:--:NRM B:01,PCI,D:00,F:00
The display may go *BLANK* on and off for up to 10 seconds during access to the EEPROM depending on your display adapter and output device.
Identifying EEPROM...
EEPROM ID (EF,3012) : WBond W25X20A 2.7-3.6V 2048Kx1S, page
Reading adapter firmware image...
IFR Data Size : 1112 bytes
IFR CRC32 : 189B4216
IFR Image Size : 1536 bytes
IFR Image CRC32 : 4552879D
IFR Subsystem ID : 1462-2825
Image Size : 99328 bytes
Version : 80.04.C3.00.21
~CRC32 : D6321A32
OEM String : NVIDIA
Vendor Name : NVIDIA Corporation
Product Name : GK104 Board - 20050000
Product Revision : Chip Rev
Device Name(s) : GeForce GTX 770
Board ID : E12D
PCI ID : 10DE-1184
Subsystem ID : 1462-2825
Hierarchy ID : Normal Board
Chip SKU : 425-0
Project : 2005-0000
CDP : N/A
Build Date : 06/03/13
Modification Date : 06/18/13
UEFI Support : No
UEFI Version : N/A
UEFI Signer(s) : Unsigned
Board: Asus Z9PE-D8 WS
Bios: Version 5206
VGA: MSI GTX 770 2GB/OC
PSU: Corsair TX750
CPU: Intel Core E5-2687W Default CPU settings, no OC
MEM: Crucial 2133Mhz 16GB
HDD: Kingston HyperX 250GB SSD
COOLER: Thermaltake
OS: Windows 7 64x Pro
Sign-On Message : GK104 P2005 SKU 0000 VGA BIOS
MSINV282MS.352Quote from: flobelix on 19-November-13, 16:07:12
Don't bump your posts: >>Please read and comply with the Forum Rules.<<
I guess you mean ASUS Z9PE-D8 WS and not WD. That is a dual cpu socket XEON workstation board not meant for gaming (hardware). The NV282MS.352 vbios the vga uses is a current one. Contact Asus and report the compatibility issue and maybe they can help you with.
My use of my system is video editing. It uses gpu heavily for encoding. Hence, the hot GFX card I just purchased. I have been in contact several times with Asus, since they also produce an N770 card, and they do not have any known compatibility issues with their own products, at least. The card worked perfectly with this N770 card when it had the previous BIOS. It was when I upped the BIOS to the latest version that I had the issue. Other GFX cards do work. The N770 wont finish POST. 100% fail. I ended up purchaseing a new BIOS chip with the previous bios flashed, since they could not produce a procedure for me to downgrade. However, I will not be able to use new CPUs with the later micro-codes until I find a way to update the BIOS. Otherwise, I would be FD&H with the old one.
Thanks for the reply,
Rod -
UEFI Bios Request for MSI Twin Frozr III HD 7950 O/C Non Boost card, has 7970pcb
Its this one Version: 015.020.000.000.001083 You make this forum far to complicated to navigate for old people , could not figure out how to insert an image, and you can't post external links either. So i linked the bios version, great cards by the way i have two of them, purchased a new motherboard that supports UEFI so I wanted to try. Thanks. More info:
GPU Device Id: 0x1002 0x679A
113-C3861300-X01 113-MSITV277MS.202 TAHITI B0 PROH C38613 GDDR5
3GB 500E/150M
(C) 1988-2010, Advanced Micro Devices, Inc.
ATOMBIOSBK-AMD VER015.020.000.000.001083
C3861300.101 PowerTune Limit: 175 to 260
CCC Overdrive Limits
GPU Clock: 1100.00 MHz
Memory Clock: 1575.00 MHz
Clock State 0 Core Clk: 880.00 MHz
Memory Clk: 1250.00 MHz
Flags: Boot Clock State 1
Core Clk: 880.00 MHz
Memory Clk: 1250.00 MHz
Flags: Optimal Perf Clock State 2
Core Clk: 880.00 MHz
Memory Clk: 1250.00 MHz
Flags: UVD Clock State 3
Core Clk: 300.00 MHz
Memory Clk: 150.00 MHz Flags:S/n : 602-v277-05sb1205073711 first card S/n 602-v277-05sb1206017147 for Msi Twin Frozr III Hd 7950 o/c regarding UEFI bios request.
-
REQUIRE One spool request for n copies in one print command in smartform
Hii Friends,
I created a smartform..I require 5 copies of that form..There is a text which needs to be changed in evry copies...eg Original in first copy
Duplicate in second copy
Triplicate in third copy....n so on
So i used a loop n i am calling smartform 5 times....The problem is i need one spool request to be created..
Note: By default sometimes it create one spool request and sometimes 3 spool request...
Pls share your inputs ............
Thanks,
Regards,
Sujit.hi,
this is more complicated see below description from help
regards,darek
Printing Several Forms in One Print Request
Use
You want to bundle several forms into one print job.
Print Request vs. Spool Request
SAP Smart Forms allows you to bundle several forms to form one output unit. This output unit is called a print request. A print request is different from a spool request:
Whether a new spool job is created in the spool depends on the settings in the spool dialog.
Whether a new print request starts depends on the standard parameters of the generated function module you set in SAP Smart Forms. For each print request, the spool dialog is called only once. If you suppress the dialog, you can pass parameters for spool processing only at the beginning of the print request.
This means that a print request gathers several forms before submitting them to spool processing. Thus they cannot be spread over several spool requests. Vice versa however, you can include several print requests into one spool request.
Procedure
Use function module SSF_FUNCTION_MODULE_NAME to retrieve the name of the function module generated from the Smart Form (see also: Integrating the Smart Form Into the Application).
Call the Smart Form for the first time and set the NO_CLOSE parameter of the control structure. This prevents the print request from being closed after accepting the output of the Smart Form and allows you to include all other form output into this print request as well. Leave the NO_OPEN parameter empty.
Instead of calling the Smart Form for the first time you can also call function module SSF_OPEN .
If you want to start a new spool request for the print request, set the TDNEWID field of the Output Options in this first call.
For all other form output of the application program that you want to include into the print request, use a loop to set both the NO_OPEN field and the NO_CLOSE field of the control structure.
To close the print request, in the call of the last Smart Form set the NO_OPEN parameter and unmark the NO_CLOSE parameter.
Instead of calling the Smart Form for the last time, you can also call function module SSF_CLOSE .
Result
The forms you called in the steps described above are included into one print request. If in the first step you started a new spool request, you can now view its status in the spool request overview (transaction SP01 ). -
HELP: Customizing ESS Leave Request for multiple entries in one submission
Hi experts,
I appreciate help on this urgent problem. We're on ECC6 with EP7. My customization requirements are below:
1) Allow multiple leave entries to be submitted at one go. Standard ESS only allows one date range entry per submission. We've customized the Webdynpro Leave request form to allow multiple entries in table form.
Assuming there's 3 requests:
R1 ~ 01-Oct-2007
R2 ~ 03-Oct-2007
R3 ~ 05-Oct-2007
Whenever user clicks 'New Entry' button, Webdynpro will call bapi PT_ARQ_REQUEST_PREPARE to generate a new request ID.
When user clicks on 'Review' button, I will loop at the requests internal table and check each of the entries, which is an individual request, via BAPI PT_ARQ_REQUEST_CHECK. Am I doing correctly so far?
The checks return no error. Next comes the problem. When I click the 'Send' button, I will loop at the request IDs (in ascending order) into BAPI PT_ARQ_REQUEST_EXECUTE. I will get a dump, saying that the object cannot be found. Debugging shows that it cannot find the first request ID (R1) in the memory. I found that if I sort the request IDs in descending order, it will be able to find the last request (R3) and could process it. However, when it comes to the 2nd last request (R2), it will give me the same dump saying that object can't not found. Both R1 and R2 cannot be found whereas only R3 can be found.
In overview, the logic we adopted is like this:
1) PT_ARQ_REQUEST_PREPARE-CREATE (R1)
2) PT_ARQ_REQUEST_CHECK (R1) upon clicking 'New Entry' Button
3) PT_ARQ_REQUEST_PREPARE-CREATE (R2)
4) PT_ARQ_REQUEST_CHECK (R2) upon clicking 'New Entry' Button
5) PT_ARQ_REQUEST_PREPARE-CREATE (R3)
6) PT_ARQ_REQUEST_CHECK (R1, R2, R3) upon clicking 'Review' Button
7) Loop PT_ARQ_REQUEST_EXECUTE ( R3 - Returns OK, R2 - Returns object not found and terminates, R1 - not processed because execution terminated by R2).
Can anyone please advise me how I should go about changing the BAPIs? Or are the CLASSes/BADIs to be changed?
<b>Points will be rewarded for helping with this urgent requirement.</b> Thank you.
Regards,
DamienHi Kiran,
Thanks for replying. My guess initially was also that the requests are overwritten.
I heard of another company's implementation who did the same concept and was able to do it. Unfortunately, I'm unable to get any information from them.
Initially, my frontend programmer and I thought of adopting the 'dummy checks' methodology. i.e. Do dummy checks when clicking 'New entry' or 'Review' button. This is to ensure that the entries were entered correctly at front end. Only when the user clicks on the 'Send' button, my BAPIs take in a table of request entries and perform the Request_Prepare&Request_Check&Request_Execute one at a time.
This may be expensive as there will be double the processing needed. One set for dummy checks and one set for the actual backend processing.
Is there any way that I can create multiple requests in 'transcient' state so that it won't be overwritten and I can still find it when I call the BAPI PT_ARQ_PREPARE_EXECUTE? PT_ARQ_PREPARE_EXECUTE only takes in request IDs instead of request structures.
Thanks again, Kiran, for replying. Have a good weekend.
Regards,
Damien -
BIOS Request for G580 Model 2189 Windows 7 x64
Hello, could someone please provide an original BIOS for G580 Model 2189 x64 Windows 7? Thank you!
Not to difficult to find... Why the "original" BIOS request? Usually not a good idea to backstep BIOS unless directed to by support professionals. Also, BIOS updates are independant of Windows Versions, the installer or "flashing": program used to install the BIOS file is sometimes Windows version dependant.
Either way - check this page for BIOS files: http://support.lenovo.com/us/en/products/laptops-and-netbooks/lenovo-g-series-laptops/lenovo-g580-no...
Good luck. -
Custom BIOS requested for the MSI GP60 2PE Leopard
Hi,
Is it possible to generate a BIOS update, for allowing the notebook to have 32 GB (2x16 GB) SODIMMs. It seems that the Memory Reference Code needs some adjustments to allow this. I got currently the MSI GP60 2PE Leopard (i7-4700HQ • 16 GB DIMM).
The currently available modules are IMM2G64D3LSOD8A-B15E or the IMM2G64D3LSOD8A-C15E from Intelligent Memory.
With kind regards,
Rolandnope, can't do such modifications
-
GOP / UEFI BIOS Request for MSI R7950 Twin Frozr III
I am looking for a GOP / UEFI compatible BIOS for my GPU. I believe my 7950 has the 7970 PCB.
S/N: 912-V803-685B1101002350
Current BIOS: h-t-t-p://up.ht/18pwh6B
More Info:Quote
GPU Device Id: 0x1002 0x679A
113-C3861300-X03
113-MSITV277MS.270 TAHITI B0 PROH2 C38613 GDDR5 3GB 500E/150M
(C) 1988-2010, Advanced Micro Devices, Inc.
ATOMBIOSBK-AMD VER015.031.000.001.001867
V27717S.SB
PowerTune Limit: 200 to 300
CCC Overdrive Limits
GPU Clock: 1100.00 MHz
Memory Clock: 1575.00 MHz
Clock State 0
Core Clk: 960.00 MHz
Memory Clk: 1250.00 MHz
Flags: Boot
Clock State 1
Core Clk: 960.00 MHz
Memory Clk: 1250.00 MHz
Flags: Optimal Perf
Clock State 2
Core Clk: 880.00 MHz
Memory Clk: 1250.00 MHz
Flags: UVD
Clock State 3
Core Clk: 300.00 MHz
Memory Clk: 150.00 MHz
Flags:
Thank you!Ah, yes you are correct. I just double checked everything and I uploaded the wrong BIOS file and BIOS info (I was messing around with different BIOSes and upped the wrong one). My serial number is 100% correct, though. This is the current one I have:
015.020.000.000.001083 (Download link: https://mega.co.nz/#!31gBjJ7A!Yr3bX088I8I5aSK0CbEF3hSAm3dhWgVfbb0rvw2 kVVQ)
Just out of curiosity, what is the difference between that version and the version of the one I linked which was "015.031.000.001.001867"? Is it a newer version? Or is there a newer version for my particular card? -
Hey all,
I'm kinda new to flashing bios on a video card so if I could get some tips that would be great, I have two r9 280x from msi and I'm wondering if they are on the latest build, also since I have 2 is there something I need to know about flashing both? I know I have a dual bios, what should I set them to in order to flash? Sorry for all the newb questions I attached a gpuz file of my current bios.
dropbox.com/s/4d2m36hctouu4fp/Tahiti.rom...
Thanks for all the help really appreciated!!>>GOP / UEFI Vbios requests - Read Here First<<
-
GOP/UEFI BIOS Request for N660GTX Twin Frozr III OC(2013-11-14)
I request GOP/UEFI BIOS for N660GTX Twin Frozr III OC.
S/N is : 602-V287-050B1301155833
BIOS Version is:80.06.28.00.39 (P2030-0000)
Current BIOS is uploaded in this URL.: htt p:// pc-diary.com/temp/GK106.zip
thank you.There it is: https://forum-en.msi.com/index.php?action=dlattach;topic=174110.0;attach=12237
-
UEFI GOP BIOS request for GTX 760
HI, I'd like to request a GOP bios for my twin frozr gtx 760:
s/n: 602-V284-440B1407039912
BIOS download link: h**ps://www.sendspace.com/file/f29lal
thanks!oh right! My computer still isn't doing UEFI fast boot properly - the BIOS post screen still shows up for 5-10 seconds (even though I've set the post screen time to 0) - after that it's a 4-5 second boot into windows 8. I figured it was the graphics card my BIOS was having trouble with, must be something else...!
Maybe you are looking for
-
Mi I Pod shows me that I need to plug it in to I Tunes. When I do I get a pop up stating that I need to enter my passcode in order to do so. Unfornuately my I pod Touch won't give the option to do so. Any suggestions anyone?
-
Trouble connecting Windows Vista to TC
I have a Windows Vista laptop that just received a new hard drive that will see my TC and says that it is connected at excellant strenght, looks it connects wirelessly to the TC but will not go out to the internet. Shows the conection as "local"? I h
-
BLOCKING THE PAYMENT TO VENDOR LINE ITEM IN APP
I am doing APP Run in F110. Here I want to block one vendor line item. In the Edit proposal button I tried to block the line item. But system is throughing a Error messeage saying that You cannot block the payment in proposal run. Can any one pls
-
SecureConnection in Java ME 3.0 problem
I'm trying to use SecureConnection to do a simple query, using www.google.com port 443 and sending a simple GET request. My test app code is at the end of this post. The behaviour I observe is that after the socket is open if I allow the thread to ge
-
Integrationevent.wsdl incomplete ?
Hi. I have to access to an Integration Queue created. In other posts, I 've read that I have to download the integrationevent.wsdl and generate a proxy, for example with jdeveloper. I 'm using jdeveloper 10.1.3.5. I 've downloaded others .wsdl from "