Bios Settings for 785GT-E63

Where can I find BIOS settings for the 785GT-E63 that will give me the most optimum performance for my system? My system consists of:
Nvidia GeForce 7300GT graphics card-256MB memory
G.Skill-4GB DDR2 PC2-6400 Memory
Phenom X3 8600-2.3 GHZ
Coolermaster case with 2-120MM fans
Coolermaster 500 watt PSU
Stock cpu cooling fan
Can someone tell me what I need to do to optimize this system? Would like to buy another CPU, but not sure if I am getting the most out of this one. Help!!

Quote
Would like to buy another CPU, but not sure if I am getting the most out of this one.
How do you mean? If your CPU is correctly recognised, and operates at its native speed of 2.3ghz, then you're getting the most out of it.
Does your system work without issues? Does it do everything you require of it, and do it well?
If yes, and yes, then stop fretting and enjoy your system, instead of trying to look for problems that aren't there.
Of course, if you want to try and push your system further, then you'll have to start overclocking. But we have a whole seperate area for that here, and you should post your questions there.

Similar Messages

Suggested K8T Neo BIOS settings for CL 3 Kingston Value RAM

G'evening!
I'll be putting together a system with the Athlon 64 3000 and K8T Neo board and had a question about optimal BIOS settings for paired Kingston non-ECC DDR 3200 RAM (2x512mb) that's CAS 3. Should have gotten some CAS 2.5 probably but this is what I have for now so in it goes. I'm reading the quick users guide and noticed that you can manipulate the CAS, TCRD, TRAS, and TRP.
First question: Will the board's auto detect do a good job in picking out a stable configuration?
2nd question: If you had to or wanted to make manual settings, what would you suggest? The CAS value is rather easy since I guess it should be set to 3 but what settings would one pick for the others?
And if I still have your attention...
The other things that will be going in the system are the infamous Maxtor 120 gig SATA HD, a XFX 5900FX video card, Lite-On combo burner. Powersupply is an Antec Solution Series 400W PS. After reading the forums for a bit I get the impression that you shouldn't forget to load the SATA Promise drivers so the HD will get recognized. My SATA drive will be the only drive in the system and will of course be the boot drive. Any other possible pitfalls or problems I should know about with the Maxtor SATA's and the K8T Neo board?
Also, I had thought I read from a review that the Zalman Al-Cu CPU heatsink/fan will fit on this board. Of course after seeing it in my hands for the first time I thought that it was a pretty damn big heatsink. Anyone else using this heatsink? (haven't taken it out of the packaging yet so that's why I wanted some impressions).
Thanks for any advice you can give me. It's been a bit of time since I built a computer and I'm sure there's alot of basic things I'm relearning along with the fact that the Athlon 64 is fairly new technology. On the other hand, when it's running smoothly...

Cant offer anything on the Timing, (sorry as I am Intel Fodder ), But I can assure you that the Zalman 7000-AlCu, Will Indeed Fit onto your Motherboard (With Room To Spare!) :biggthumbsup:I can attest to this because My buddy just installed the Zalman 7000-AlCu on his K8T ....And He loves it! As do I ....It's about the only thing that we have in common as far as PC'S Go .........Sean REILLY875

Best BIOS settings for Kt3 Ultra2 and Geforce4?

Hi,
Can someone tell me what the best BIOS settings would be for my KT3 Ultra2 running a Geforce4 ti4200?
I get crappy scores in 3dMark2001 SE and I have the infamous stuttering/crashing problems in 3D games. I've tried pretty much every configuration of settings and drivers I can think of.
I saw on these forums that the Kt3 Ultra2 can be a bit fussy with GF4 cards. If someone could post the best BIOS settings for performance and stability I'd be eternally grateful.
Alternatively, email me at [email protected] with them.
Thanks in advance

very very similar as far as i can make out

Bios Settings For MSI K8N Neo4/SLI Platinum MB

Hello all... Has anyone came up with the best and most stable bios settings for the MSI K8N Neo4/SLI Platinum motherboard yet. Specifically under the CPU and Memory menus.
If anyone has seen any, please post them. or post a link.
Thanks
DaaDoctor

Well that depends on the installed CPU and memory, doesnt it? So I find that question kinda odd.
One thing though: Dont use Cool n Quiet.

Default Bios Settings for RS480MS-IL2

Hi all
I am just wondering if there is some hidden key that loads some Default Bios Settings for this board? I know there is an Optimized Settings option, but i haven't seen a Default one.
I am using version bios version 3.8
Thanks.

have you tried a better psu
a 128 mb ram consumes around around 8 to 10 watts
http://www.blueowltechnologies.com/pmConsumption.asp
volts x amps =watts
3.3v feeds ram
so at most you have 46 watts on a good day

How to install Windows 7 in UEFI modeand what bios settings for D30

How do you install windows 7 in UEFI mode and what bios settings do I need to install it on a D30 workstation.

Not a ThinkStation guy, but FWIW, that can happen when installing Win 7 in UEFI mode when CSM support is not enabled in BIOS.
Is CSM support - either explicit or by selecting "other OS" and turning UEFI back on as suggested above - an option?
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Ideal BIOS Settings for online gaming

this is my 1st computer that i built. i have a lot of experience in wiring high-end electronics, so wiring this little rig with barely any visible wires/cables was a breeze. I bought the processor/mobo with the intention of only doing minor O/C as i dont really know all that much on the hardware side of improving performance. with that said, i've searched for timings and settings for my specific combination, and i cant find any. again, i dont really want to push the config past a safe level, as i will be selling this machine when the 64's come down in price. can someone help me set the proper frequencies/timings? i have a lot to learn, and even in the normal bios settings i don't know if certain things should be enabled or disabled for my main purpose, which is to simply play 3D online games very fast. i will be changing out the GeforceFX5200 PCI for a 5600 AGP in a week or so. I'm noticing that my old Comcrap PIII 1.0Ghz w/512SDRAM with this video card gets just as good a ping ingame as this rig does. the machine starts quickly, runs offline programs quickly, but online it isnt as fast as i'd hoped. from what i've read in the other forums, there are many settings in the bios that are enabled by default that don't need to be. can someone help me decipher which settings are useful and which are not. i loosely understand some of the settings but if someone could help with the questions below and/or do a walkthru for bios geared toward gaming i'd really appreciate it. The machine runs very cool (CPU 104*F/SYS 93*F) but i dont know what else needs adjustment. I simply want to make this machine go as fast and as hard as it can with the right config. i don't want to unlock the processor yet or do anything else major at this point.
1: Best yet safe Voltage for my processor and RAM
2: FSB clock; 133 or 166? had problems @ 200
3: S.M.A.R.T. on or off?
4: Best IRQ/PCI slot for video card
5: "GoodMEM" utility: how much should i safely allot?
6: Video BIOS Cacheable?
7: Multiplier setting for K7N2DeltaL & XP2600+
8: VGA Aperture (my card is 128MB but PCI. upgrading soon)
i'll be learning more as i go along, so i dont really need a full explanation of what's what, lol THIS TIME. all i need is a rundown where someone tells me what to leave alone, and what to change for a very fast yet safe gaming rig

OK I'm officially confused.
I bought the retail boxed AthlonXP2600+, which clearly states on the packaging "With 333 MHZ Frontside Bus". i bought the board over others, one reason being it supported 400MHz FSB. I go into "Advanced Chipset Features" and when i set the "System Performance" to "Manual", i can then go into the "CPU FSB Clock" settings, but the max it will allow me to go to is 233MHz (which won't boot and i have to flip the jumpers. when i had set it to 200MHz before, it failed to boot as well... PLEASE can someone look over these settings and tell me the OPTIMAL settings for taking this combo as fast as it can go w/o overclocking? What am i doing wrong? what multiplier do i need to be at. I'm under the impression that the combo works best when the clock speed of the board is at the same speed as the processor. here are the BIOS settings with which i need advice:
ADV. BIOS
Virus Warning [Disabled]
External Cache [Enabled]
Quick Boot [Enabled]
1st Boot [Floppy]
2nd Boot [HDD]
3rd Boot [CD]
Boot Other Device [Enabled]
Swap Floppy [Disabled]
Seek Floppy [Enabled]
Boot Up Num Lock LED [On]
Gate A20 Option [Fast]
Typematic Rate Setting [Disabled]
Security Option [Setup]
APIC Function [Enabled]
MPS Table Version [1.4]
BOOT OS/2 for DRAM>64MB [No]
HD S.M.A.R.T. [Enabled]
Video BIOS Cacheable [Enabled]
ADV. CHIPSET
System Performance [High Performance]
CPU FSB Clock [166MHz]
AGP 8x Support [Enabled]
AGP Fastwrite Support [Enabled]
System BIOS Cacheable [Disabled]
Video RAM Cacheable [Enabled]
AGP Aperture Size [128MB]
I do currently have a PCI GeForceFX5200 8o, but im getting an AGP FX5600 this week. i know my card has nothing to do with AGP, but i've left most of the AGP settings alone since i'll be using it later. is this creating a bottleneck or tying up system memory to have it this way for now?
FREQUENCY/VOLTAGE CTRL
AGP Clock Value [Default]
xAGP Clock Value [66]
AGP Voltage Adjust [1.5V]
DRAM Voltage Adjust [2.7V]
CPU Ratio [By H/W]
CPU Vcore Select [By H/W]
PCI Clock Auto-Detect [Enabled]
Again, I have an 333MhzFSB Chip and a board that will support up to 400MhzFSB. help!

Need help with bios settings for Neo4 Platinum

Hi. I've checked several guides on bioses and still have questions about my settings. I'm not an overclocker, so I'm looking for stability over anything else (although I don't want my computer to run like a pig . I'll post what I have and the parts of the bios that I'm unsure of. I also have saved pictures of a Cpu-z scan if that helps. Any suggestions are much appreciated!
Here's my stuff:
Motherboard: MSI K8N NEo4 Platinum (MS-7125)
Processor: AMD Athlon 64 3000+ 512K 90nm (Winchester socket 939)
   clock frequency: 1800mhz
   system bus: 2000
   operating mode: 32/64
   voltage: 1.40v
   max temp: 70 degrees C
   thermal power: 89w
   L1 cache: 128KB
   L2 cache: 512KB
   cmos technology: 90nm SOI
   memory controller: 128-bit
Award bios version: 1.9
Installed ram: Micron Crucial Ballistix 512MBx2 (1024MB total) (Crucial
part number BL6464Z402)
   PC3200 400mhz Dual-Channel DDR Dimm (184 pins)
   configuration: 64Meg x 64
   unbuffered/non-ecc
   voltage: 2.8v
   memory timings:   2-2-2-6
Here's my current bios settings (I've only listed sections that contained settings that I was unsure of):
ADVANCED BIOS FEATURES
quick booting: enabled
boot to os/2: no
ioapic function: enabled
mps table version: 1.4
full screen logo display: disabled
seek floppy: enabled
typematic rate setting: enabled
typematic rate: 30
typematic delay: 1000
security option: setup
ADVANCED CHIPSET FEATURES
--->>DRAM CONFIGURATION
timing mode: manual
memclock index value: 200mhz
cas# latency TCL:2
min ras# active time TRAS: 6t
ras# to cas# delay TRCD: 2t
row precharge time TRP: 2t
row to row delay TRRD: auto
row cycle time TRC: 8t
row refresh cyc time TRFC: 11t
read-to-write time TRWT:auto
write recovery time TWR:auto
write to read delay: TWTR:auto
refresh period TREF:auto
user config mode: auto
x bottom of 32-bit [31:24] io: D8
x 1t/2t memory timing: 2t
x read preamble value: 8ns
x async latency value: 9ns
s/w memory hole remapping: disabled
mtrr mapping mode: continuous
PNP/PCI CONFIGURATIONS
primary graphic's adapter: first pcie
resources controlled by: auto (escd)
x irq resources setup: press enter
maximum payload size: 4096
CELL MENU
current cpu clock: 1810 mhz
current ddr clock: 201 mhz
high performance mode: manual
aggressive timing: disabled
dynamic overclocking: disabled
adjust cpu fsb frequency: 200
ht frequency: 5x
ht width: (down arrow 16/up arrow 16)
cpu spread spectrum: disabled
sata spread spectrum: disabled
pcie spread spectrum: disabled
pcie clock: 100 mhz
sse/sse2 instructions: enabled
cool'n'quiet: disabled
adjust cpu vid: startup
extra cpu voltage: by cpu vid
cpu voltage 1.400v
memory voltage: auto
nf4 voltage: 1.50v
Thanks again. xpfshost

I'll do that, thanks. I guess I'm really mostly clueless about the following items:
memclock index value: 200mhz
row cycle time TRC: 8t
row refresh cyc time TRFC: 11t
current cpu clock: 1810 mhz
current ddr clock: 201 mhz
adjust cpu fsb frequency: 200
ht frequency: 5x
ht width: (down arrow 16/up arrow 16
pcie clock: 100 mhz
Do they look OK?? Thanks!
xpfshost
Quote from: Grayone on 19-April-07, 05:13:03
Change your user config mode in dram configuration to manual and change your memory timing to 1T. The 1T setting will speed up your memory slightly.

BIOS settings for a AMD 2100+ in K7N2 Delta ILSR

Hi can some one tell me what i set the bios settings too for a AMD 2100+ and PC3200 DDR ram in the bios of a K7N2 Delat ILSR.
I dont want to over clock the system just run it at the stock speeds.
Cheers

set FSB to 133 and FSB/Dram ratio to 1:1 you will be underclocking your ram but you will get more peformance running in sync

Ideal KT4V BIOS settings for XP2500+ Barton

I've read AMD's recommendations for the KT4V BIOS settings http://www.amdforums.com/showindex.php?s=&threadid=186506 , but they seem to be very generic. I would like to know the settings that would give me the highest performance, without causing any instability, using my present system and usage. My son does 3D animation and gaming on this computer. This is a stand alone computer (no network). The latest version BIOS for the KT4V offers an option in Power Management Features to enable CPU HALT Command Detection. I heard that this would work better than Cooler XP in cooling the CPU. I enabled it and my CPU Temp dropped 6-10 degrees C. Is this recommended? What is the down side of this action? My system is as follows: AMD Athlon XP 2500+ w/ Vantec VA4-C7040 CPU fan (w/Arctic Silver 3) MSI KT4V mobo Gainward Golden Sample Ti/450 TV w/ 128MB DDR (GeForce3 Ti 200) 2 - Kingston 512MB PC2700 DDR RAM Antec TRUE550 power supply 1 - 40GB 7200RPM hard drive 1 - 30GB 5400RPM hard drive 1 - CD-ROM 1 - CD-RW 1 - floppy drive Windows XP home Any help would be appreciated. Thank you, Barry

As a result of my research, these are the BIOS settings that I am using. My computer runs well and is stable.
* MSI KT4VL BIOS SETTINGS w/AMD XP 2500+ w/ Barton *
==================
Standard CMOS Features
==================
Time Set Correctly Upon first POST and after each BIOS Flash / CMOS Reset
Date Set Correctly Upon first POST and after each BIOS Flash / CMOS Reset
Primary IDE Master
Type AUTO
32Bit transfer Mode ON
Primary IDE Slave
Type AUTO
32 Bit Transfer Mode ON
Secondary IDE MasterType AUTO
32 Bit Transfer Mode ON
Secondary IDE Slave
Type AUTO
32 Bit Transfer Mode ON
Floppy Drive A Set Appropriately
Floppy Drive B Not Installed
Boot Sector Virus Protection Disabled
===================
Advanced BIOS Features
===================
Quick Boot Enabled
Full Screen Logo Show Disabled
Boot Sequence
1st Boot Device Floppy
2nd Boot Device CDROM/DVD whatever you use
3rd Boot Device IDE 0
Try Other Boot Devices No
S.M.A.R.T. for Hard Disks Enabled
BootUp Num-Lock On
Floppy Drive Swap Disabled
Floppy Drive Seek Disabled
Primary Display VGA/EGA
Password Check Setup
Boot to OS/2 No
Internal Cache Enabled
System BIOS Cacheable Disabled
C000,32k Shadow Disabled
APIC Function Enabled
MPS Table Version 1.4
=======================
Advanced Chipset Features
=======================
DRAM Timing Control
Current Host Clock Displays current FSB Frequency
Configure SDRAM Timing By SPD (Set to User first to change RAM timings)
SDRAM frequency 333 for PC2700 and above
SDRAM CAS# Latency 2
Row Precharge Time 2T
RAS Pulse Width 5T
RAS to CAS Delay 2T
SDRAM Bank Interleave 4-Bank
SDRAM Burst Length 8QW
SDRAM 1T Command Enabled
Fast Command Fast (start here and if Windows installs stable set to Ultra)
Fast R-2-R Turnaround Enabled
AGP timing Control
AGP Mode 4X
AGP Fast Write Disabled
AGP Aperture Size 256MB
AGP Master 1 W/S Write Enabled
AGP Master 1 W/S Read Enabled
AGP Read Synchronization Enabled
PCI Delay Transaction Enabled
========================
Power Management Features
========================
IPCA Function Yes
ACPI Standby State S1/POS
Call VGA at S3 Resuming Disabled
USB Wakeup From S3 Enabled
Power Management/APM Enabled
Power/Sleep LED Single LED
Suspend Time Out (Minute) Disabled
Display Activity Ignore
CPU Critical temperature 70 degrees C CPU HALT Command Detection Disabled
Power Button Function On/Off
After AC Power Loss Power Off
Set WakeUp Events
Wake Up on Ring Disabled
Wake Up on PME Disabled
Resume On KBC Disabled
Wake Up Key Any Key
Wake Up Password N/A
Resume on PS/2 Mouse Disabled
Resume By Alarm Disabled
Alarm Date 15
Alarm Hour 12
Alarm Minute 30
Alarm Second 30
===================
PnP/PCI Configurations
===================
Plug and Play Aware O/S Yes
Clear NVRAM No (Set One time only to Yes After Installing New Hardware or Moving PCI Cards Around)
PCI Latency Timer 64 (Set Higher for better PCI performance reduce if having sound or LAN problems)
PCI IDE BusMaster Enabled
Primary Graphics Adapter AGP for AGP card - PCI for PCI video card)
PCI Slot 1 IRQ Auto
PCI Slot 2/5 IRQ Auto
PCI Slot 3/6 IRQ Auto
PCI Slot 4 IRQ Auto
===================
Integrated Peripherals
===================
Floppy Disk Controller Auto
Serial Port 1 Disabled
Serial Port 2 Disabled
Serial Port 2 Mode Normal
IR Pin Select IRRX/IRTX
Onboard Parallel Port Auto
Parallel Port Mode ECP (For some Printers you may need to set as Bi-Dir or EPP)
EPP version N/A
Parallel Port IRQ Auto
Parallel Port DMA Auto
Onboard Midi Port Disabled
Onchip IDE Controller Both
Onboard LAN Enabled (Disabled if using PCI LAN card)
Onboard LAN PME Enabled (Disabled if using PCI LAN card)
AC’97 Audio Enabled (unless using PCI sound card)
MC’97 Modem Disabled
USB Controller All 6 USB Ports
USB Legacy Support Disabled (some people with legacy USB devices may need to enable)
Port 64/60 Emulation Enabled
===============
PC Health Status
===============
Chassis Intrusion Disabled
CPU Fan Detect Enabled (set to disabled BEFORE shutting down to install any PSU powered CPU fan)
======================
Frequency/Voltage Control
======================
Spread Spectrum Disabled (return to default setting to troubleshoot EMI problems)
CPU FSB Clock 166
CPU Ratio Auto
CPU Vcore (V) Auto
DDR Voltage (V) Auto (set to 1.6 if you have RAM instability)
Termination Voltage Auto
AGP Voltage (V) Auto

Bios settings for K9A2 v1.0 and PC2-8500 1066MH

My apologies in advance if this issue is like beating a dead horse but I have been looking for stable bios recomendations and proper settings for over a week now not only in this forum but the msi german board as well where I found my beta last year. I built my system a year ago and have never been 100% satisfied with it as it totally screams but intermittenly BSOD and reboots while gaming usually in heavy action :o(
I had a difficult time getting a working bios and configuration in Jan '08 but all I remember was it was in ganged, 128 bit mode, and had spread spectrum and other auto disable pci something setting disable and I have been able to run memory at 1066MHz.
after last crash a week ago I replace my beta 1.3 bios with A7376AMS V1.7B4 011309 out of desperation to correct the random booting issus as well as suspected over heating as I have tried removing the side panel to my coolermaster Cosmos to see if getting more air one components would help and I cant tell but I do know I cannot get the system back to 1066Mhz
currently runing unganged 64-bit and any attempt to change that and Cell settings causes BSOD in Vista 64-Bit, I cannot figure out how to adjust the voltage as the settings are greyed out. If anyone has a working bios could you supply me version info as well as how to set correct voltage and any other setting to stablize. yes, I have memory still in first two slots.
thanks for your time
Strato
AMD PHENOM 9600 BLACK EDITION 2.3 GHz
MSI K9A2 PLATINUM v1.0 | Bios v1.7B4 011309
GeIL Esoteria 4GB (2X2GB) PC2-8500 1066 MHz
ATI Radeon HD 3870 X2 1GB
Thermaltake Toughpower 750w
CoolerMaster Cosmos
Seagate 1000GB | Seagate 750GB
Vista Business 64-Bit

Stratoscape , i used untill now with K9A2 Platinum v2 BIOS-es like 1.2 ,1.5, 1.66 ,1.6 and i can say that this 1.7b4 seems better though i used it for only 2 days.DPC Latency checker shows a lot of improovement over BIOS 1.6.
I have used Geil RAM untill 2 months ago,but the board wasnt working properly with it so i changed to Kingston.Maybe you should barrow from a firend other brand modules and see how they work
Or maybe you should use them at 800 Mhz.
Leave the timings on auto and adjust only the voltage .

BIOS settings for 1 SATA + 3 IDE devices

Hi,
I'm a newbie to PC assembly so please pardon my ignorance.
I am trying to install 1 SATA harddisk + 2 IDE harddisk and a DVD Writer on my MSI 865PE NEO2-PLS. I have tried playing around with the BIOS but this does not seems to work. Can anyone advise on the possibility and the BIOS settings?
Thanks.
P4 3.0C HT enabled
PC 3200 TwinMos DDR400
MSI 865PE NEO2-PLS
MSI Radeon 9200SE 128MB
Maxtor 120GB @ SATA-1 no RAID
Seagate 40GB 7200rpm IDE
IBM 10GB 7200rpm IDE
LG 4160B 16x DvD Rewriter IDE

Until you get Windows installed, only hook up the drive you plan on running windows on.
Since you have 3 PATA devices you have to use Native mode. The Native settings given by NovJoe are for booting from a PATA drive. If you decided to use the SATA drive, change SATA only to PATA only and make sure both PATA Keep Enabled and SATA Keep Enabled are set to Yes

BIOS settings for MSI 770-c45 - overclocked with a Phenom II 550 Black Edition

Hi,
Wish I could say I knoew what these bios settings are, but I can't - I really need some help here. Anyone who has this m/b knows that there is a dip switch to help you get a 10%/20% perf increase, but it fails for me...
Anyone have some advice onthe appropriate settings?
Many thanks,
Sayer

here's mine:
Phenom II X2 550BE@4ghz
MSI 770-C45 bios 1.3B2
Team Xtreem DDR3 1866 C8 running DDR3 1550 7-7-7-21@1,8v
cooling Thermalright Ultra 120 extreme, dual fans
bios settings (Cell menu only, I dont think the others setting would affect)
* AMD Cool N' Quiet--->disabled
* CPU Fsb freq--->230mhz...might different with yours, depend on your CPU though
* CPU Ratio--->17.5
* CPU-NB Ratio--->x9
* EC Firmware--->normal
* Advanced Clock calibration--->disabled
* Auto Overclock--->disabled
* multi-step OC booster--->disabled
* HT link control--->x9
* vcore--->1,55v (must use good cooling with this voltage)
* vdimm--->1,84v
* NB voltage--->1,2v
* CPU-NB voltage--->1,33v
other setting are all auto

Best BIOS Settings for Performace?

Hi Guys,
I am new to all this PC stuff, i was a mac user for the last 8 years. At the moment i am learning all this stuff on the Bios - can anybody help me out give me the best settings for my PC (without overclocking)? I understand if i disable cool n quiet - i will get better performance.
my info:
AMD 64 3200+
K8T Neo FIS2R Mainboard
2 x 512MB DDR400 (1 gig totalling) Kingston
9600XT Bravo (powercolor) 128MB
550W Antec True Power Supply
TT Venus 12 CPU Fan
Idle - 36 - 37c
Full load - 41 - 45c
I ran the 3dmark03 (demo) and the score came up 4005 - i am not sure if this result is how it should be but i really think its slow compared to my mate's 2600 XP running 9700pro and getting a score of around 5500.
Any suggestions/tips would be appreciated.

Quote
Originally posted by NestyPops
Hi Guys,
I am new to all this PC stuff, i was a mac user for the last 8 years. At the moment i am learning all this stuff on the Bios - can anybody help me out give me the best settings for my PC (without overclocking)? I understand if i disable cool n quiet - i will get better performance.
my info:
AMD 64 3200+
K8T Neo FIS2R Mainboard
2 x 512MB DDR400 (1 gig totalling) Kingston
9600XT Bravo (powercolor) 128MB
550W Antec True Power Supply
TT Venus 12 CPU Fan
Idle - 36 - 37c
Full load - 41 - 45c
I ran the 3dmark03 (demo) and the score came up 4005 - i am not sure if this result is how it should be but i really think its slow compared to my mate's 2600 XP running 9700pro and getting a score of around 5500.
Any suggestions/tips would be appreciated.
3dMark03 is very GPU-demanding, and your mate's 9700pro is a faster card then your 9600XT.
Try runing 3dMark01 and it whill test the hole system more or less.
About biossettings I'm to new to A64 to give any suggestions, but memory timing have big effekt on preformens.

Best BIOS settings for K8N?

Can people post up their BIOS settings and give any tips? It'd be good to know how the ones having luck with the board are running them

Are you talking about settings for overclocking? Or just settings in general?

Bios Settings for 785GT-E63

Similar Messages

Maybe you are looking for