BIOS settings for a AMD 2100+ in K7N2 Delta ILSR

Hi can some one tell me what i set the bios settings too for a AMD 2100+ and PC3200 DDR ram in the bios of a K7N2 Delat ILSR.
I dont want to over clock the system just run it at the stock speeds.
Cheers

set FSB to 133 and FSB/Dram ratio to 1:1 you will be underclocking your ram but you will get more peformance running in sync

Similar Messages

Need help with jumper settings for k7n2 delta ilsr

I have a k7n2 delta ilsr and I'm using a AMD 2800+ barton 333 fsb. I'm not sure what the jumper settins are for this cpu. The users guide only shows 133/166 and 200, can anyone help me with the jumper settings.
Thanks, Ron.

Hi,
As your processor is 333FSB - the jumper should be set to 166FSB as should the BIOS. As your RAM CPU combination runs at 2x166=333 or thereabouts.
Basically, as a general rule, if you halve the FSB speed of your processor you'll get the setting for both BIOS and Jumper. 200FSB=100, 266FSB=133, 333FSB=166 etc. etc.
Axel

Suggested K8T Neo BIOS settings for CL 3 Kingston Value RAM

G'evening!
I'll be putting together a system with the Athlon 64 3000 and K8T Neo board and had a question about optimal BIOS settings for paired Kingston non-ECC DDR 3200 RAM (2x512mb) that's CAS 3. Should have gotten some CAS 2.5 probably but this is what I have for now so in it goes. I'm reading the quick users guide and noticed that you can manipulate the CAS, TCRD, TRAS, and TRP.
First question: Will the board's auto detect do a good job in picking out a stable configuration?
2nd question: If you had to or wanted to make manual settings, what would you suggest? The CAS value is rather easy since I guess it should be set to 3 but what settings would one pick for the others?
And if I still have your attention...
The other things that will be going in the system are the infamous Maxtor 120 gig SATA HD, a XFX 5900FX video card, Lite-On combo burner. Powersupply is an Antec Solution Series 400W PS. After reading the forums for a bit I get the impression that you shouldn't forget to load the SATA Promise drivers so the HD will get recognized. My SATA drive will be the only drive in the system and will of course be the boot drive. Any other possible pitfalls or problems I should know about with the Maxtor SATA's and the K8T Neo board?
Also, I had thought I read from a review that the Zalman Al-Cu CPU heatsink/fan will fit on this board. Of course after seeing it in my hands for the first time I thought that it was a pretty damn big heatsink. Anyone else using this heatsink? (haven't taken it out of the packaging yet so that's why I wanted some impressions).
Thanks for any advice you can give me. It's been a bit of time since I built a computer and I'm sure there's alot of basic things I'm relearning along with the fact that the Athlon 64 is fairly new technology. On the other hand, when it's running smoothly...

Cant offer anything on the Timing, (sorry as I am Intel Fodder ), But I can assure you that the Zalman 7000-AlCu, Will Indeed Fit onto your Motherboard (With Room To Spare!) :biggthumbsup:I can attest to this because My buddy just installed the Zalman 7000-AlCu on his K8T ....And He loves it! As do I ....It's about the only thing that we have in common as far as PC'S Go .........Sean REILLY875

New Modded BIOS for K7N2 Delta ILSR

MSI K7N2 Delta ILSR Modded BIOS based on Official v. 7.80 BIOS
download here:

Description: Access through interface which is on insecure interfaces list detected. Request aborted.
Interface/Client IP address:
Date: Wed, 18 May 2005 13:11:17 GMT
Doesn't work for me
By the way did u put the bios to vork with 1.3 vcore like the braziliantech one that does't exist anymore ?
EDIT: Thanks it's working now

Best BIOS settings for Kt3 Ultra2 and Geforce4?

Hi,
Can someone tell me what the best BIOS settings would be for my KT3 Ultra2 running a Geforce4 ti4200?
I get crappy scores in 3dMark2001 SE and I have the infamous stuttering/crashing problems in 3D games. I've tried pretty much every configuration of settings and drivers I can think of.
I saw on these forums that the Kt3 Ultra2 can be a bit fussy with GF4 cards. If someone could post the best BIOS settings for performance and stability I'd be eternally grateful.
Alternatively, email me at [email protected] with them.
Thanks in advance

very very similar as far as i can make out

Bios Settings for 785GT-E63

Where can I find BIOS settings for the 785GT-E63 that will give me the most optimum performance for my system? My system consists of:
Nvidia GeForce 7300GT graphics card-256MB memory
G.Skill-4GB DDR2 PC2-6400 Memory
Phenom X3 8600-2.3 GHZ
Coolermaster case with 2-120MM fans
Coolermaster 500 watt PSU
Stock cpu cooling fan
Can someone tell me what I need to do to optimize this system? Would like to buy another CPU, but not sure if I am getting the most out of this one. Help!!

Quote
Would like to buy another CPU, but not sure if I am getting the most out of this one.
How do you mean? If your CPU is correctly recognised, and operates at its native speed of 2.3ghz, then you're getting the most out of it.
Does your system work without issues? Does it do everything you require of it, and do it well?
If yes, and yes, then stop fretting and enjoy your system, instead of trying to look for problems that aren't there.
Of course, if you want to try and push your system further, then you'll have to start overclocking. But we have a whole seperate area for that here, and you should post your questions there.

Bios Settings For MSI K8N Neo4/SLI Platinum MB

Hello all... Has anyone came up with the best and most stable bios settings for the MSI K8N Neo4/SLI Platinum motherboard yet. Specifically under the CPU and Memory menus.
If anyone has seen any, please post them. or post a link.
Thanks
DaaDoctor

Well that depends on the installed CPU and memory, doesnt it? So I find that question kinda odd.
One thing though: Dont use Cool n Quiet.

Default Bios Settings for RS480MS-IL2

Hi all
I am just wondering if there is some hidden key that loads some Default Bios Settings for this board? I know there is an Optimized Settings option, but i haven't seen a Default one.
I am using version bios version 3.8
Thanks.

have you tried a better psu
a 128 mb ram consumes around around 8 to 10 watts
http://www.blueowltechnologies.com/pmConsumption.asp
volts x amps =watts
3.3v feeds ram
so at most you have 46 watts on a good day

Help! amd xp3000+ barton temp's.... k7n2 delta ilsr

Hi all, (sorry for the lengthy post)
Ive recently built a new system based on the K7N2 DELTA ILSR, great mobo, however my cpu temps are extremely high! on idle 48C and on load nearly 60C. the mobo temp hits approx 40c on load and 34 on idle.
I had an issue with cooling as the cpu heat diode would freeze my pc as it was hitting temps of 58c on idle. i was using the coolermaster aero 7+.... no good at all!!!!! even when on full rpm. Now im using a vantec 80mm fan on a Thermalright SLK-800A. much improved, however still extremely hot.
after reading this review (section headed: Heat Dissipation: Thermal Conditions and S2K Bus Disconnect) :
http://www.xbitlabs.com/articles/cpu/display/athlonxp-3000.html
......on "S2k bus disconnect" created by AMD for the barton range.
As the article states, it reduces Cpu temps ALOT!! but im not too sure ion how to activate it or even if my MSI motherboard supports it....
Can anyone shed some light???
system:
Radeon 9800
1GB 3200 Ram
xp 3000+ Barton
Sound Audigy 2
Thanks, Sav

Sorry about the long reply!!! the first thing i would like to say is why does this happen at 58C even with the bios temp settings diabled??? pehapes MSI could Answer this?
I have spent countless hours trying to fix this problem and a lot of £££. A bit of background to me I am a design engineer and i like my PC to work well. I have the following main components
xp3200+ based system (Max die 85C)
with dual 512ddr sticks running at 400mhz
Matrox Parphilia
10K SATA hard disk
7,200 133ATA hard drive
Plus motherboard Nvidia chipset
these all kick out a lot of heat the (CPU contributing 76.8w).
first i started out with a very cheap case and standard amd heatsink. I found after about 5 minutes my pc kept crashing i automatically thought that it was probably the case temperature so monitored this found every time cpu reached 58C it crashed on the dot. The only conclusion i can draw from this that this MB has some thermal protection that can not be switched off but i am guessing perhapes MSI would like to answer this.
I quickly decided as an engineer that the best thing would be to go and buy a aluminuim case with lots of case fans (Basically a big heatsink itself). After a lot of searching i settled for a Coolermaster ATC110. It has four case fans all run at full speed all the time. Now this stoped the crashing problem it only now crashes if i put it under continous loading. Then i went out and bought a new cpu heatsink to replace the amd standard one. This had a minor effect on cpu temp but again under high loads the system crashed at 58C. Obvoiusly as an engineer i satred to think that the amount of noise the system with all its fans going at max is like being put in a wind tunnel.
I then turned to looking at the thermal diserpation requiremnts of all the bits in my system. I worked out that i need to disserpate 281Wmax of heat with my current setup. The kind of heat a small electric fire produces!!!. I begun to wounder if i could shift enough air through the two exhaust fans at the rooms ambient temp to do this. After some calculations I found that my case exhaust case fans are only just surfficent to disspate this amount. Which could explain this the crashing. because the higher the case temp the lower the capability of the heatsinks to conduct heat away from the item.
In the end i gave up with active cooling methods (heatsinks and fans) and realised my only option was to go for external cooling. I now have the system setup with a koolance exos cooling both hardisks graphics card cpu and MBchipset. I know this is very extreme but the case fan noise got to me now i have disconected all case fans except for the ones in my thermaltake power supply which are virtually silent. After about 12 evenings of testing and installation I now have a system which is not only stable but the CPU temp is only 32C.
Obvoiusly getting the heat out of the case is a good idea. The Exos is only running at it's lowest setting which means the fans arnt making any noticable noise.
MOST IMPORTANTLY IT DOES NOT CRASH ANY MORE. AND THERE IS THE PSSIBILTY OF OVERCLOCKING.
The question still remains though why 58C?

MSI K7N2 Delta ILSR - RAID BIOS Option ???

hi ho,
i have my 2 storage devices pluged into the promise 376 onboard controller. they are not connected as a real raid (not mirror nor real stripe). my OS is win2k on the first sata device and everything was fine for a long time.
but now when my system boots, it detects the ide drives and then i see the irq board.
right after that the system stops and tells me 'disk boot failure'. so i don`t get the chance to configure my raidcontroller or my sata devices.
it is as the controller is deactivated. i remember a bios version where you could activate and deactivate the sata controller. but in my bios (right now it is v7.8) there is no such option.
i have tested so far:
- reset cmos
- flash bios v7.5 to 7.8
- disconnected sata drives
anyone with similar problems or any suggestion?
> MoBo : K7N2 Delta-ILSR Bios v7.8
> CPU : AMD Barton 2500+ (not overclocked)
> Ram : TwinMos 1GB 3200 400Mhz
> Sata : 2 x Maxtor 120GB Sata (as single Devices on Raid-Controller)
> Ide : 60GB IBM DeckStar
> Gra : ATI 9600 pro 128MB
> Aud : SB Audigy 2 ZS
> Pow : SilverPower 350W, +3,3V/+5V@25A and 12V@18A
> OS : win 2000 SP4 + Security Updates 31.07.04 + DirectX 9.0c

watch the bottom of the screen after pressing Enter on the "Welcome to Setup" screen. There will be some moments of files being loaded, and then you should see a message appear which says "Press F6 if you need to install a 3rd party SCSI or RAID driver". This message will only stay on the screen for a couple of seconds, so press F6 as soon as you see it appear. After this is done, you will see other messages appear, and it will act as though nothing is happening, but eventually a screen will appear which will allow you to install the drivers for the sata controller.
specify a device press S, select "win 2000 promise fasttrak 376 controller" it will read floppy and load, dot not remove floppy yet, continue win2000 install it may nead to access floppy to finish installing raid driver, did you do it like this.
try making some floppy boot disks and boot to floppy instead of cd.
http://freepctech.com/pc/002/files010.shtml
when you say there not listed, where did you see this? they wont be listed, windows will search for fasttrak controller so it will see sata's conected to it with out you knowing, so long as you load the controller from floppy that came with mobo as above.

MSI K7N2 Delta ILSR Bios v.7.6 ??When??

Hello,
I just asked myself when MSI is going to publish a new Bios Update above the 7.6 for the K7N2 Delta ILSR mainboard !!! I think it's time for a new Bios update, because of the few problems with this mainboard !!!!

Quote
He has confirmed the ports are present on the board....
I have seen this in earlier Nf2 Pre Delta boards where it was there but if you had disabled it, and then flashed the BIOS, it would dissapear. The only way to get it back was to flash to an earlier version, make sure it is enabled, then you can flash to the latest.
That is why I always clear the CMOS when starting a new build. You may have a board that may have been fiddled with, believe it or not, it does happen from time to time.
Have you tried the Default BIOS Settings Option in the BIOS? Perhaps you loaded the Performance option and that is why it is hiding?
this worked, thx a lot

FLASH BIOS MSI K7N2 Delta-ILSR ????????

I am trying to flash the BIOS of my K7N2 Delta-ILSR board. I follwed all the instructions from the MSI Web but I can't get it going. I booted from Win ME & Win98 but could not get into C: drive. So I used Command Prompt from Window to get into the C: drive and follwed the Flash Bios Procedures. I keep getting the message: AwdFlash No Support WinNT/2000/XP OS
I got problem with the temp after I updated the BIOS. I wanted to flash it back to the old Bios. Please help me out
Thank you
My system:
WinXP Pro
MSI K7N2 Delta-ILSR
AMD 2500+
1 GB DR3200
Seagate 160 SATA

http://www.msi.com.tw/html/support/bios/note/ntfs.htm

MSI K7N2 Delta-ILSR Wont boot up (no display no bios)

Hi
i bought a AMD Athlon XP 3200+ & MSI K7N2 Delta-ILSR.
unfortuntly i can't boot it. it wont show anything on screen.
i have tried anything i red in this forum (clear cmos... safe mode jumper...strip all parts...)
all i get is :
blank black display, no beeps and keyboard lights flashes over and over (when connected to a KVM hub), when conected directly to keboard the lights flashes only once but stil black display and no beeps (i hear on speake,when powering up PSU, a silent short noise, no beep).
power suply turns on (new one 500w), i tried agp video card and replaced with pci video card.
memory is kingstone 512mb pc3200 400MHz x2, i tried only one of them and both in diferent sockets.
cpu: AMD xp 3200+ 400fsb.
i did succed to go into bios only once, after lots of resets and shutdowns and bios clear (after ouers)
i choosed in the bios: load bios defaults, and thats it. i hoped it starts up but nothing.
i did all testing i know (checked all pins, cables, clear cmos...all, you name it)
all parts are brand new (except motherbord. it's seconds hand from eBay. i've bean talled that it works fine)
i also e-mailed MSI support that question. (2 days ago. no answer yet)
oh...and i have a pci POST diagnostic card and its 7seg display don't shows any numbers, only when once i succed to get into bios. i don't have the msi original D-Breket addon diag.
can you help me?

hi guys
here is my PSU specs:
Colors-It 500w-Max Silent ATX Power Supply
Voltage 115/230V
Current 10A/5A
Frequency 60/50Hz
+3.3 +5 +12 -12 -5 +5SB BLK GRN GRY
30A 50A 15A 1.0A 1.0A 2.5A COM P-ON PG
connectors:
ATX-2.03 Connector: 1
ATX-12V Connector: 1
CD-Rom/HD 4 Pin connector: 6
Floppy 4 Pin Connector: 2
Serial ATA Connector : 1
cpu: AMD Athlon XP 3200+
MotherBoard: MSI K7N2 Delta-ILSR More: http://www.msicomputer.com/product/p_spec.asp?model=K7N2_Delta-ILSR&class=mb
Memory: kingstone 512mb pc3200 400MHz x2 More: http://www.ec.kingston.com/ecom/configurator/PartsInfo.asp?ktcpartno=KVR400X64C3A/512
i have other brand of memory moduls (micron pc2300) i tried them too. no go.
i tried other PSU, i pulled from my brothers pc (amd xp 1400+).
as i said before, i have pci POST diagnostic card so it could tell me any problem. iguss it's the mobo, posibly bios upgrade.
but if mobo not showing bios, i can't update bios from floppy.
and the tested the mobo out side the case on a antistatic mat and i useed an antistatic strip.
as i said i could get into the bios once, after many resets....choosed 'load bios defaults..', restarted and.....no go.

AGP Setup For k7n2 delta ilsr

I have a k7n2 delta ilsr mb, in display properties on desk top setting tab then advanced button then GeForce tab under adapter information is Bus and memory. To the right of Bus it reads AGP (PCI mode) shouldn't that read AGP (8X), how can I change this. Ron.

Hi,
No, leave it at 64 or 128.
Go here for an explanation:
http://www.rojakpot.com/default.aspx?location=7&var1=18
Then - Click on: "Free Access To the BIOS Optimization Guide" near the bottom of the page - then click on "AGP Aperture Size"
Axel

Temperature reading for K7N2 Delta ILSR

I have a 2500+ Barton (333 FSB) to work with K7N2 Delta ILSR and 2x256 MB Samsung DDRAM(400 FSB).I use MBM to read my CPU temperatures.Usually 45-47 C idle and 54-58 C under full load.I overclock CPU to 400 FSB and I get LOWER TEMPERATURES!!!!!
I use 1:1 bios setting for CPU and DRAM speeds either 333 or 400 FSB.
How can this by possible?

I use Speedfan which seems to follow the temp in the bios. I've heard that MBM is also accurate. As far as your temps going down on a OC that is very odd indeed.

BIOS settings for a AMD 2100+ in K7N2 Delta ILSR

Similar Messages

Maybe you are looking for