BIOS update, then will not boot from any drive

This old laptop, 3000 C200 8922 was acting very clunky when on wireless.
Downloaded Bios Version 63ET62WW and flashed it into the bios.
Now, even though I can get to the bios screen, and it shows the hard drive, DVD/CD drive, it will NOT boot from either.
It will also "see" a usb installed, but will not boot from it.
I have removed all power and cleared the CMOS several times and I still have nothing. Tried two different hdd's which have been in the machine and same results. 
HELP!! I should have never messed with it......

hi k4pew,
One rule after a BIOS update is to Load optimize deafults after updating.
   Try that go inside BIOS Hit F9 to load defaults then F10 to Save and Exit.
If not
Try turning on the computer and start hitting F1 to load the Recovery Menu and see if that will push then Try Reseting the PC.
If still the same Im afraid that the BIOS needs to be reflashed.
Im not aware of any flash tool or a your Previous BIOS Version Firmware available for download.
You can try calling Lenovo Technical Support for any options available for repair.
Im sorry to hear what happened
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Similar Messages

  • IMac will not boot from any mode except Target Disk

    I have an Early 2008 Penryn iMac 24" MB398LL/A running OS X 10.7.4 (see specs below) that will not boot from ANY mode, It also has several strange vertical bars from top to bottom on the screen. They are about 10 px wide, with some pixels empty and looks a bit like a barcode if you squint at it.
    I have tried Safe Boot, Force Boot, DVD Boot, FireWire/USB Boot,  and it always gets to the same point. It gets to the apple screen with the spinning gear and then after about 8 seconds it freezes. The only way it works at all is in Target Disk Mode. It pops right up on my Macbook Pro and I was able to grab all my info!
    I have run Disc Utilities and Tech Tool on it many times from my MBP and it passes every test.
    I reformatted the HD and installed 10.7 again, it still freezes up at the same point. 
    I have tried using Single User mode and every time have had to run /sbin/fsck -fy twice because it always says the disk is ok but it was modified on the first pass.
    I thought maybe it had a bad video card or logic board but and I ran the Apple Hardware Test on many occasions and it always passes. Recently I was told about Loop Mode and just completed running the AHT for just over 30 hours without any errors at all.
    UPDATE...
    Strange Part… I tried installing Mountain Lion in Target Disk Mode and everything went smoothly. When it restarted on its own the lines on the screen were gone for the moment, but the Mac still freezes up on the spinning gear and immediately restarts on its own.  I have run every thing listed above on it and still nothing. Sometimes the lines reappear then in two more starts they are gone.
    I did manage to have it start one time got a copy of the  the error report (its at the bottom too) The Mac ran for at least 30 minutes with no problems, then the screen went crazy a few seconds and it became unresponsive. The mouse moved but that was all it could do. Now my iMac continually restarts itself, I don't have any more ideas, HELP!
    Specs...
    The iMac "Core 2 Duo" 3.06 24-Inch Aluminum (Early 2008/Penryn) features a 3.06 GHz Intel "Core 2 Duo" processor (E8435), with two independent processor "cores" on a single silicon chip, a 6 MB shared level 2 cache, a 1066 MHz system bus, 2 GB of RAM (800 MHz DDR2 SDRAM, PC2-6400), a 500 GB (7200 RPM) Serial ATA hard drive, a vertically-mounted slot-loading DVD±R DL "SuperDrive", NVIDIA GeForce 8800 GS graphics acceleration with 512 MB of GDDR3 memory, a built-in iSight video camera, and built-in stereo speakers underneath the 24" glossy TFT Active Matrix LCD (1920x1200 native) display.
    Error Report…
    Sat Sep  1 17:13:12 2012
    panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
    CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
    RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
    RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
    R8:  0x0000000000000000, R9:  0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
    R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
    RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS:  0x0000000000000008, SS:  0x0000000000000010
    Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0

    Here is the complete error log...
    Sat Sep  1 17:13:12 2012
    panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
    CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
    RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
    RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
    R8:  0x0000000000000000, R9:  0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
    R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
    RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS:  0x0000000000000008, SS:  0x0000000000000010
    Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0
    Backtrace (CPU 0), Frame : Return Address
    0xffffff80602db800 : 0xffffff801a41d5f6
    0xffffff80602db870 : 0xffffff801a4b7b95
    0xffffff80602dba40 : 0xffffff801a4ce4ad
    0xffffff80602dba60 : 0xffffff7f9bab8654
    0xffffff80602dbb60 : 0xffffff7f9baa218c
    0xffffff80602dbbb0 : 0xffffff7f9baa20e2
    0xffffff80602dbbd0 : 0xffffff7f9ba73554
    0xffffff80602dbc00 : 0xffffff7f9aa8d470
    0xffffff80602dbc40 : 0xffffff7f9aa8d3df
    0xffffff80602dbc60 : 0xffffff7f9aa926ec
    0xffffff80602dbcf0 : 0xffffff7f9aa8af20
    0xffffff80602dbd20 : 0xffffff7f9aadacc7
    0xffffff80602dbd70 : 0xffffff801a833b9b
    0xffffff80602dbdc0 : 0xffffff801a862d57
    0xffffff80602dbe30 : 0xffffff801a497cef
    0xffffff80602dbe80 : 0xffffff801a420abd
    0xffffff80602dbeb0 : 0xffffff801a410448
    0xffffff80602dbf00 : 0xffffff801a4195fb
    0xffffff80602dbf70 : 0xffffff801a4a5ad6
    0xffffff80602dbfb0 : 0xffffff801a4ced13
          Kernel Extensions in backtrace:
             com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000->0xffffff7f9aab8fff
                dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
             com.apple.NVDAResman(8.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aad8 000->0xffffff7f9addafff
                dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
                dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
                dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
             com.apple.GeForce(8.0)[4B9BE287-5251-398E-96B0-BB16C9BFB2D9]@0xffffff7f9ba72000 ->0xffffff7f9bb34fff
                dependency: com.apple.NVDAResman(8.0.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aa d8000
                dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
                dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
                dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
    BSD process name corresponding to current thread: WindowServer
    Mac OS version:
    12B19
    Kernel version:
    Darwin Kernel Version 12.1.0: Tue Aug 14 13:29:55 PDT 2012; root:xnu-2050.9.2~1/RELEASE_X86_64
    Kernel UUID: 3005059E-270B-3B9F-940D-7A66C05DDC9D
    Kernel slide:     0x000000001a200000
    Kernel text base: 0xffffff801a400000
    System model name: iMac8,1 (Mac-F227BEC8)
    System uptime in nanoseconds: 26349024446
    last loaded kext at 22534854703: com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2 (addr 0xffffff7f9c489000, size 12288)
    loaded kexts:
    com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2
    com.apple.driver.AppleHDA          2.3.0f2
    com.apple.driver.AppleTyMCEDriver          1.0.2d2
    com.apple.filesystems.autofs          3.0
    com.apple.iokit.IOBluetoothSerialManager          4.0.9f8
    com.apple.iokit.IOBluetoothUSBDFU          4.0.9f8
    com.apple.driver.AppleLPC          1.6.0
    com.apple.driver.AppleMuxControl          3.2.6
    com.apple.driver.AppleBacklight          170.2.3
    com.apple.driver.AppleUpstreamUserClient          3.5.10
    com.apple.driver.AppleMCCSControl          1.0.33
    com.apple.GeForce          8.0.0
    com.apple.driver.AppleSMCPDRC          1.0.0
    com.apple.iokit.IOUserEthernet          1.0.0d1
    com.apple.Dont_Steal_Mac_OS_X          7.0.0
    com.apple.driver.ApplePolicyControl          3.2.6
    com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
    com.apple.driver.AppleIRController          320.15
    com.apple.iokit.SCSITaskUserClient          3.5.1
    com.apple.driver.AppleFileSystemDriver          3.0.1
    com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
    com.apple.BootCache          34
    com.apple.driver.XsanFilter          404
    com.apple.iokit.IOAHCIBlockStorage          2.2.1
    com.apple.driver.AppleFWOHCI          4.9.5
    com.apple.driver.AppleUSBHub          5.1.6
    com.apple.driver.AirPortBrcm43224          600.36.17
    com.apple.iokit.AppleYukon2          3.2.3b1
    com.apple.driver.AppleAHCIPort          2.4.0
    com.apple.driver.AppleIntelPIIXATA          2.5.1
    com.apple.driver.AppleUSBEHCI          5.1.5
    com.apple.driver.AppleUSBUHCI          5.1.5
    com.apple.driver.AppleEFINVRAM          1.6.1
    com.apple.driver.AppleRTC          1.5
    com.apple.driver.AppleHPET          1.7
    com.apple.driver.AppleACPIButtons          1.6
    com.apple.driver.AppleSMBIOS          1.9
    com.apple.driver.AppleACPIEC          1.6
    com.apple.driver.AppleAPIC          1.6
    com.apple.driver.AppleIntelCPUPowerManagementClient          196.0.0
    com.apple.nke.applicationfirewall          4.0.39
    com.apple.security.quarantine          2
    com.apple.driver.AppleIntelCPUPowerManagement          196.0.0
    com.apple.driver.DspFuncLib          2.3.0f2
    com.apple.iokit.IOAudioFamily          1.8.9fc9
    com.apple.kext.OSvKernDSPLib          1.6
    com.apple.kext.triggers          1.0
    com.apple.iokit.IOSerialFamily          10.0.6
    com.apple.driver.AppleSMBusPCI          1.0.10d0
    com.apple.driver.AppleBacklightExpert          1.0.4
    com.apple.driver.AppleSMBusController          1.0.10d0
    com.apple.nvidia.nv50hal          8.0.0
    com.apple.NVDAResman          8.0.0
    com.apple.iokit.IOFireWireIP          2.2.5
    com.apple.driver.AppleHDAController          2.3.0f2
    com.apple.iokit.IOHDAFamily          2.3.0f2
    com.apple.iokit.IOSurface          86.0.2
    com.apple.iokit.IOBluetoothFamily          4.0.9f8
    com.apple.driver.AppleGraphicsControl          3.2.6
    com.apple.iokit.IONDRVSupport          2.3.4
    com.apple.iokit.IOGraphicsFamily          2.3.4
    com.apple.driver.AppleSMC          3.1.3d11
    com.apple.driver.IOPlatformPluginLegacy          1.0.0
    com.apple.driver.IOPlatformPluginFamily          5.2.0d16
    com.apple.iokit.IOUSBHIDDriver          5.0.0
    com.apple.driver.AppleUSBMergeNub          5.1.5
    com.apple.driver.AppleUSBComposite          5.0.0
    com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.5.1
    com.apple.iokit.IOBDStorageFamily          1.7
    com.apple.iokit.IODVDStorageFamily          1.7.1
    com.apple.iokit.IOCDStorageFamily          1.7.1
    com.apple.iokit.IOATAPIProtocolTransport          3.5.0
    com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.1
    com.apple.iokit.IOFireWireFamily          4.5.5
    com.apple.iokit.IOUSBUserClient          5.0.0
    com.apple.iokit.IO80211Family          500.15
    com.apple.iokit.IONetworkingFamily          3.0
    com.apple.iokit.IOAHCIFamily          2.2.0
    com.apple.iokit.IOATAFamily          2.5.1
    com.apple.iokit.IOUSBFamily          5.1.6
    com.apple.driver.AppleEFIRuntime          1.6.1
    com.apple.iokit.IOHIDFamily          1.8.0
    com.apple.iokit.IOSMBusFamily          1.1
    com.apple.security.sandbox          220
    com.apple.kext.AppleMatch          1.0.0d1
    com.apple.security.TMSafetyNet          7
    com.apple.driver.DiskImages          344
    com.apple.iokit.IOStorageFamily          1.8
    com.apple.driver.AppleKeyStore          28.18
    com.apple.driver.AppleACPIPlatform          1.6
    com.apple.iokit.IOPCIFamily          2.7
    com.apple.iokit.IOACPIFamily          1.4
    com.apple.kec.corecrypto          1.0
    Model: iMac8,1, BootROM IM81.00C1.B00, 2 processors, Intel Core 2 Duo, 3.06 GHz, 2 GB, SMC 1.30f1
    Graphics: NVIDIA GeForce 8800 GS, NVIDIA GeForce 8800 GS, PCIe, 512 MB
    Memory Module: BANK 0/DIMM0, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
    Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
    AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.131.36.16)
    Bluetooth: Version 4.0.9f8 10405, 2 service, 18 devices, 1 incoming serial ports
    Serial ATA Device: WDC WD5000AAKS-40YGA1, 500.11 GB
    Parallel ATA Device: MATSHITADVD-R   UJ-875
    USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd400000 / 2
    USB Device: BRCM2046 Hub, 0x0a5c  (Broadcom Corp.), 0x4500, 0x1a100000 / 2
    USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x820f, 0x1a110000 / 5
    USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x5d100000 / 2
    USB Device: Hub in Apple Extended USB Keyboard, apple_vendor_id, 0x1002, 0x1d100000 / 2
    USB Device: Trackball, 0x046d  (Logitech Inc.), 0xc404, 0x1d120000 / 4
    USB Device: Apple Extended USB Keyboard, apple_vendor_id, 0x0204, 0x1d110000 / 3

  • G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD

    We have a DP 1ghz Quicksilver PowerMac G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD that came with the machine.
    We were in the process of installing 10.4 Tiger before placing it for sale.
    The Mac was originally OSX Server 10.1 that we later converted to a worksation running 10.3 Panther.
    It has 1 GB of memory, 80GB hardrive, 250MB Zip Drive and a Radeon 7500 video card.
    Since this machine only has a CD-R drive and not a DVD-R, we installed Tiger using another Mac via Target Disk Mode. The installation process went well, but when I tried to reboot I got a Kernel Panic right after startup screen with the grey Apple logo.
    On some reboots we get to the blue startup screen, others it stops at the grey Apple logo, others a black box like the a Kernel Panic - but with no text. Twice it went directly into Open Firmware.
    We have done the following during our troubleshooting:
    - Reseat RAM, Video Card, Hard Drive, Zip & CD-R connections
    - Remove RAM 1 stick at a time and reboot
    - Replace RAM with RAM from another working Quicksilver
    - Replace Video Card with one from another working Quicksilver
    - Zap PRAM
    - Reset CUDA switch
    - Unplug the MAC and remove everything (RAM, Battery, etc) for 30 minutes and try to reboot
    - Tried booting from the Macintosh Server G4 Software Restore CD
    - Tried booting from Mac OS X Server CD
    - Tried booting from AppleCare Protection Plan CD with TechTool
    - Tried booting from Diskwarrior CD
    - Tried booting from an external FireWire drive with a disk image of Tiger OS Install
    - Tried booting with the hard drive disconnected
    The Mac WILL boot from the Apple Hardware Test CD and will pass ALL of the extended tests.

    Conventional wisdom says that any Mac that will not boot up from a System/Install CD OS 9 or an Install CD Mac OS X, has a Hardware problem.
    The diagnostic CD is a red herring because it uses a very primitive method of reading the CD, and so does not properly represent the machines general ability to read CDs.
    I would look at the CD drive cables, etc, and see if another drive gives different results.
    You have not mentioned using the Startup Manager (option key at Startup) to do any checking:
    HT1310- Startup Manager: How to select a startup volume

  • Power Mac G4 400 MHz (AGP graphics) will not boot from hard drive

    I have a Mac G4 400 MHz (AGP graphics) Machine Model: PowerMac 3.1 CPU Type:PowerPC G4 (2.8)
    When I try to boot from the hard drive I get the folder with the flashing question Mark. The Machine will start up from the OSX 10.4 installer disk.
    The system was running OSX 10.4.9 fine. I began to have problems with the hard drive, so I replaced it with an old Maxtor 5T040H4 40Gig Apple branded drive that I had sitting around.
    The drive is jumpered (r50) for Master/Single.
    I erased the drive in the old G4 using disk utility and wrote all zeros. I then used my store bought Tiger 10.4 install disk to install 10.4 on the drive.
    After restarting I still get the flashing question mark. If I leave the Install disk in the DVD drive the system will attempt to install again.
    I have zapped the PRAM, pressed the CUDA button, removed the battery and let the system sit unplugged for over and hour and it still will not boot from the hard drive.
    To test the drive I removed it and put it in a Granite Digital firewire enclosure and connected it to another mac. The drive shows up and the system appears to be installed correctly.
    What am I forgetting to do? Does anyone have any suggestions.
    Thanks in advance.
    Wesley G.

    Hi! If Tom's solution doesn't work I would reboot from the install disc and then partition the drive as 1 partition instead of erasing it. Sounds like the driver on the disk is too old and installing a new partition map should write a new driver to the drive that is compatible with Tiger. Other than that it is possible that the drive has a spin delay jumper enabled and the drive isn't spinning up fast enough and the computer isn't looking long enough for the drive. Tom

  • After 10.5 upgrade Mac will not boot from hard drive

    I just upgraded to 10.5 Leopard but my mac will not boot from the hard drive even after selecting my hard drive as the startup disk. The mac will start to boot but will cut itself off before the boot is complete. I have to leave the Leopard disk in the mac and hold down C to get the mac to turn on but it only allows me to install the software again.

    instead of archive and install you might first want to try restoring your system using TM to some time point before your failed 10.5.1 upgrade. Then try upgrading to 10.5.1 again. I would suggest downloading the full 110 MB upgrade and installing it manually rather than doing it through the software upgrade menu.
    You can download the upgrade here:
    http://www.apple.com/downloads/macosx/apple/macosx_updates/macosx1051update.html

  • Satellite P300-1A8 will not boot from disc drive

    Hi,
    I had a little play with start up programs, partitioning the hard drive and marking as active and deleting programs i thought i did not need.
    I obviously had no idea what i was doing!
    Laptop will go to toshiba screen then goes blank, i can not boot from the disc drive.
    I put the hard drive into another laptop and it works fine.
    I put the hard drive of that laptop in the buggered one and that works fine.
    How the hell do i put the original one back with it working??
    Really really stuck with this!!!!!
    Any help would be appreciated.
    Only thing i havent tried is the recovery disc but im not paying for one if it wont boot as itl be a waste of money.
    Seems like its a compatability problem with cpu and hard drive as they dont want to be friends anymore!!
    Thank you in advance

    Hi!
    Can you boot in the safe mode?
    If you dont have a recovery disk, use the Microsoft installation disk and try to boot from it.
    And you said that you cant boot from disc drive, did you tried different disks?
    Maybe some are not readable or not bootable.
    The best way would be a recovery disk. The installation takes a few minutes and you have a clean installation with all drivers and tools from Toshiba.
    Bye

  • Mac will not boot from hard drive or install disc

    Hello All
    In dire need of advise...my intel Mac will not boot, even tried booting to the Snow Leopard install disc and all I'm getting is the white screen, apple logo and the wheel.
    Just before this happened there was a buzzing sound like the fan was about to fail but that is only a guess on my part. Is there a keyboard shortcut to boot to a terminal window or similar to force the computer to boot from the install disc.
    Thanks in advance for any help offered.
    Warren

    Hi Warren
    Try holding the Option key and see if it will boot into Startup Manager, where you should be able to choose from a good Drive or your install Disk.
    http://support.apple.com/kb/HT1533
    or the D key and run the Apple Hardware Test.
    http://support.apple.com/kb/HT1509
    Also note: key commands may require a USB Keyboard if your using a wireless and it has become unpaired.
    Dennis

  • Macbook Pro will not boot from internal drive

    I have a macbook pro model indentifier: macbookpro 7,1. The system would not boot what I have tried is first running apple diagnostics and all test fine, I tried booting from a snow leopard cd to re-install and it would not boot from the cd, however it does boot from the techtool pro 6 cd. I did run the test in techtool pro and all check out ok.
    I removed the drive from the system and connected via usb to test and it boots fine from usb, put back internal and same result no boot. I did some research and I see that someone had a similar problem and it was the sata cable, but since the diagnostics test ok I am not sure that would be the problem.
    Any Suggetions, this is driving me crazy
    Thanks in advance
    Bret

    coffee would not HAVE to do anything except mechanically. It would not have any effect now since it has dried out, well short of corroding some components.
    Check the points where the HDD casing "meets" the Macbook casing. How much pressure is there?
    What about the pressure pins "pogo pins" are they all functioning?
    What about pressure on the cables?
    Please describe how it wont boot? What exactly does it do / happens

  • Macbook Pro will not boot from any source after upgrade

    Hi,
    I have a late 2011 Macbook Pro - standard issue other than more memory as I recall. It has a 750MB hard drive with more than half still free. All the checks given below are done with the computer stand-alone with no hardware attached - other than the power cord and of course WiFi.
    2 weeks ago I upgraded to Yosemite having taken all the right precautions before upgrade - thanks to Take Control. It worked fine and I was getting a good experience until last Wednesday when I put it to sleep by closing the lid. Later in the day I opened it up again but only got a grey screen. After leaving it several minutes to see if it cleared I shut down by holding the on button for several seconds then tried to re-boot. The computer starts and gets as far as the grey screen then shuts down again after several minutes. Sometimes it will continue to restart after shut down and keeps doing this until I again hold the on  button in until it finally shuts down for good.
    I have two bootable drives - one is a cloned backup of the previous version and all the data, the other is an 8GB thumb drive with a bootable version of the Yosemite installer. For the record I also have a Time Machine backup and a second full clone backup and recovery drive on a Synology NAS device -  I just haven't figured out how to boot from this device as yet.
    I can get to the boot up selection screen (hold option key) and select an external drive to boot from but it makes no difference - I still get the same grey screen. Same thing if I use Command +R to boot from the Mac HD recovery partition.
    I have also tried to boot into safe boot mode (hold the shift key down). This seems to slow everything down but ultimately has the same result - a grey screen.The only difference I can see is that this grey screen does not shut down after a time. Seems to just continue until I shut it down manually.
    I can hold Command +V to remove the grey screen and see the action being written to the screen while logging on (white text on a blue screen) - up to a point.  After some time I just get the same grey screen and it shuts down after more time. I can also use Option +D (I'm told it should be just hold the 'D' key to do this but that has never worked for me and Option +D does) to get to the hardware check and I have run this both before upgrading and after having the problem. Before upgrading I got one error - 4ETC/1/40000002. I looked this up on the Internet and could find nothing specific to identify the problem and the general consensus seemed to be it was nothing major. After upgrading and running the hardware check again (after this problem occurred) it returned no errors.
    I have reset the PRAM with the same result as before - all I get is the is the Apple logo and a progress bar that increases to around 50%, then both disappear and I get just a grey screen. After a time the computer shuts down and then restarts again and goes through the same process.
    I've done pretty much everything I can think of and find in books and on the Internet. Hoping that someone out there will find this problem interesting and help me to resolve it.
    Tony

    Problem resolved. I took the machine into an authorized repair facility where, for around $30, I had it checked and the logic board replaced. Picked it up yesterday and seems to be working OK. No cost to replace the logic board even though the machine is over 3 years old. There seems  to be some sort of dispute with Apple over a class action that has worked in my favour. Great. I'm happy.
    Tony

  • Touchsmart 610 will not boot from CD drive or USB device.

    Hi all
    I have a TouchSmart 610 and I performed a standard restart but it would not boot. I tried the various options in restart recovery to no avail.
    I made a win 7 recovery disk on another win 7 64 bit machine to try and repair the Windows os but I cannot get the PC to boot from the CD drive.
    I have altered the boot order in BIOS so that CD is first. But when I try to boot up it goes to the windows recovery screen again.
    I have an "ultimate boot" disc and tried to boot from that but same problem.
    If I look at Bot order in BIOS it still says CD is first.
    Anyone got any iddeas?
    Thanks in advance.

    Hello Grasper,
    Welcome to the HP Forums.
    I understand that you're having an issue with the computer booting from CD Rom. I will do what I can to help with this.
    Check the BIOS and make sure "legacy devices" is enabled.
    You can also try and manually boot to the CD ROM. On start up if you press F*(F8/ F9/ F11/ or ESC. it varies per computer) It will bring up a menu with the devices you can boot from. If the disk drive is listed select it and see what happens.
    If nothing happens it could be an issue with the CD ROM itself. You could try another drive in that case. If its still not working at this point, then it could mean an issue with the motherboard itself.
    I hope this was able to help you out. Thank you for posting on the HP Forums.
    I worked on behalf of HP.

  • Macbook Pro will not boot from USB drive or Macintosh HD

    The Mac in question:
    Macbook Pro mid-2009
    2.4GHz Core 2 Duo
    4GBs RAM
    OSX 10.8.4
    Basically I did a fresh install of OSX 10.8.4 and Installed Windows 7 Home Premium 64bit via Bootcamp.
    All software was up to date, I had the newest version of bootcamp for windows software, and everything was working fine.
    I lent the computer to my dad
    fast forward 3 months.
    Windows boots fine and works for about 15 minutes then Blue Screens and restarts. Endless loop.
    I did everything conveiveably possible for the Windows side before deciding to work on the Apple side.
    Come to find out, my dad had not booted into the Apple side for almost 3 months. So on holding option and selecting the Macintosh HD icon, I got the apple logo with a spinning wheel under it. The wheel spun for about a minute then stuck. No response, so I held the power button down and restarted.
    held option, and selected "Recovery 10.8.4" same deal minus the spinning wheel. stuck on the apple logo.
    so i plugged in my bootable mountain lion usb (has been used countless times and works, its not the usb) and selected the usb. Same stuck apple logo.
    I am at a loss as to what to do now. I dont care about any information on the drive, so i dont mind formatting and such.
    But i am at a loss as to how to repair it if i cant access and bootables to do a disk repair or a clean install
    Any suggestions would be helpful, thanks.
    (btw, ive reset SMC and PRAM and all the usuals and ive internet searched out the whazoo, so yall are my last resort *grin*)
    -Dusty

    New info:
    Selected Recovery disk in boot options menu and it loaded.
    Disk recovery disk verification says there are errors with Macintosh HD but it cannot repair them.
    Tried Reinstalling mountain lion from the Recovery screen and followed the instructions, signed into my Apple ID and it started installing mountain lion on Macintosh HD.
    It immediately said 4 hours to complete and the blue progress bar started moving slowly.
    it says it is "Downloading additional components, your computer will restart automatically"
    about an hour later i checked it and the bar was full, but the estimated time was 1 hour 59 minutes and it has been almost 12 hours now.
    Just trying to give a play by play so yall have something to work with.
    making a Mountain Lion bootable USB as i type, will try that as soon as its done.
    Dusty

  • Mac Mini Will not boot from external drive or install disk

    Hi,
    I just bought a new 2.0 ghz mac mini 1 gb ram. 120gb hdd.
    I have a separate external HDD attached and wanted to boot from this. It works with my MBP and IMAC.
    When i plug it into the Mac Mini and start up with Option key. It recognizes it.
    I then click on it. It automatically reboots.... then grey screen comes on. It goes black after about 10 seconds. then boots into original operating system.
    I also tried to use the MAC install Disk, thinking it might be a corruption in the shipped software. It does the same thing.
    I have MAC Install DVD on an external drive too. Same issue.
    I partitioned the HDD and installed a copy of the Mac install disk onto that with disk utility... Same thing grey screen, then black then back to original operating system.
    Not sure what is going on?
    thanks
    Chris

    Hi,
    Thanks.
    It is running 10.5.8.
    I am trying to boot up an external drive with 10.5.8 on it. It works on my Macbook Pro which is running 10.5.8, runs on my IMAC running SL. But doesnt work on the mac mini?
    It had been running SL, however there are a number of programs I have like Windows Live Sync which are not yet compatable with SL so i downgraded to 10.5.6 which came with the Mac Mini then loaded all updates.
    It seems to just go into an auto reboot as soon as i click on it.
    i thought it might be the firmware? Is it possible to downgrade them and then re-install?
    I have reset the PRAM.
    Any help would be appreciated.
    Thanks

  • IBook will NOT boot from Combo Drive

    Hi all,
    I'm trying to boot from my Tiger install DVD using the usual method - holding down "C" while pressing the power key. The DVD drive never even spins up. All I get is a gray screen with the apple - no spinning bars.
    This occurred after the latest security update trashed all logins on the machine (G4 iBook, 512 MB RAM, 80 GB HD, 10.4.9) Immediately after entering a user password, loginwindow would crash, followed by mdimport, followed by crashserver I could briefly boot using command-S, but that stopped working (blue screen).
    I then booted of the Tiger DVD, ran Disk Utility, Hardware Profiler, and used terminal to do "nvram boot-args="-v". Disk utility showed no permission or disk problems, and the profiler showed everything was there that was supposed to be there.
    Next, I did an archive-and-install. The Tiger DVD passed its verification, the installation appeared to proceed normally, the system rebooted at the end, and up came the gray screen.
    All subsequent boots only came up as far as the gray screen. I reset the parameter ram (alt-command-p-r-power), waiting for three beeps. I then tried to boot off the DVD, and now the machine doesn't even spin the drive up.
    I have also reset the PMU following the directions on the apple knowledge base.
    Is there something I've missed? I do not have another mac to try Target mode. Any suggestions would be welcome!
    TIA,
    dan
    white iBook G4 Mac OS X (10.4.9)

    Another opton is to pop in the disk, restart, holding down the OPTION key, select the disk, and click the lower-right arrow. http://docs.info.apple.com/article.html?artnum=106178 has the details.

  • MBP slow to boot and WILL NOT boot from external drive

    I have two problems. First my friends MacBook Pro which is less than a month old is taking long to load. So I did a clean install without installing anything other than what came. Still slow to boot. Sometimes I see a light blue screen for a while before getting into the desktop. She complains of the beachball far too often. She says my MacBook is faster than her Pro, which is not right.
    So I came down with my external LaCie drive, which I cloned from my iMac 24". I wasn't able to boot from the external (firewire) drive using her MacBook Pro. I thought my LaCie drive was bad or soemthing, but when I got home, I hooked it up to my MacBook and booted from the external drive just fine. I use SuperDuper to make a bootable clone.
    So as it stands now, her computer is slow to boot into the OS, and it won't let me boot from my external drive. Does anyone have any idea what this could be? I did a clean install, used cocktail, etc. If it persists, I'll tell her to take it in.
    Thanks,
    Bryan

    Robert,
    I have no idea what you mean by Apple is not responsive to the issue. If you want help, please start a new topic thread so someone can help you identify the problem without the distraction of other people's problems around yours. Blaming people does not solve problems.
    This is the link to post a new topic on this board:
    http://discussions.apple.com/forum.jspa?forumID=1149&start=0
    This is a user to user board. If you need help from Apple, call AppleCare directly here:
    http://www.apple.com/contact/phone_contacts.html

  • Mid-2009 MacBook Pro sees internal SATA hard drive, but will not boot from or format

    I inherited a Mid-2009 MacBook Pro (15-inch, 2.53 GHz model) with a very strange issue.
    It first presented itself as not being able to boot from the internal SATA hard drive that came with the computer. Nothing I tried could get it to boot, so I assumed the file system was corrupted beyond repair and booted from a CD to try to format the drive. Disk Utility on the CD would not format the drive, giving me strange error messages like "Unable to write to the last block of the device".
    At this point I figured the drive itself must be toast, so I pulled it out and put another known-good SATA hard drive in, booted from CD, and attempted to format. Again, same error messages and an unsuccesful format.
    So I had the bright idea of formatting one of the drives in an external enclosure and then putting it in the MBP to see if OS X would even install. No dice. Get a cryptic error message before installation even begins.
    So I installed OS X on the drive in the external enclosure and put it in the MBP, and it attempts to boot, but never goes anywhere.
    So to sum up, the symptoms I'm seeing:
    MacBook Pro CAN see internal SATA hard drives.
    MacBook Pro WILL NOT boot from any internal SATA hard drive and cannot format or install OS X to any internal SATA hard drive.
    MacBook Pro WILL boot from any CD or external device and seems to work properly otherwise.
    At this point I'm thinking it's one of two things: the hard drive ribbon cable or the SATA controller on the logic board.
    Since the MacBook Pro seems to work completely fine other than this one issue, and will boot properly from both external devices and the CD (also a SATA device), I'm thinking and hoping that it's just the hard drive ribbon cable. From my searches online, I've heard that this batch of MacBook Pros is known to have issues with the hard drive ribbon cable, but it seems in most cases this manifests itself by the Mac not being able to see a drive at all.
    I've done quite a bit of troubleshooting to get to this point, but right now I'm just looking for any feedback at all. Specifically I'd love to know a way I can easily test to see whether it's the logic board or the cable.

    UPDATE: An interesting development!
    I just tried a third known-good SATA hard drive, one which I believe supports SATA I only (but I'm not sure), and unlike the other drives that the Mac sees but cannot properly interact with, the Mac can't even see this one when I put it inside.
    Frustrating as this may be, I believe I'm actually getting closer to a solution since my symptoms now appear to be closely aligned with people having SATA ribbon cable issues.
    Onward!

Maybe you are looking for