Bios wont boot up new memory

Does has anyone have any idea what I need to do.I have a MS-6334 motherboard ,pIII 800mhz intel cpu.Its currently running with 128mb memory.I am trying to increase the memory to 512mb.I have 2 modules of 256 mb SDRAM pc133 3.3vunbuffered.Everytime I time I boot up with this Ram my pc gets stuck in the POST, not even getting past the first beep.I have tried it with different Ram.My original ram seems to be working.

Quote
Originally posted by wonkanoby
crucials ram selectoe came up with this
http://www.crucial.com/store/listparts.asp?Mfr%2BProductline=MSI+%28Micro+Star%29%2BMSI+%28Micro+Star%29+Motherboards&mfr=MSI+%28Micro+Star%29&cat=RAM&model=MS-6334+%28815M+Pro%29&submit=Go
SDRAM, PC133 • CL=2 • Unbuffered • Non-parity • 7.5ns • 3.3V • 32Meg x 64
how does yours compare is it 32megx 64 or some thing else
It is Samsung M366S3253 [URL=http://www.samsungelectronics.com/semiconductors/search/partnumbersearch.jsp?pageno=1&partnumber1=M366S3253DTS&partnumber2=C7A
it is SDRAM,pc133unbuffered .Non parity.

Similar Messages

Laptop wont boot with new memory installed please help

Hi I am trying to upgrade my laptop memory to two gigs When putting in the I gig modules in each slot the laptop will not boot. When I put in the original 256 memory module in slot one and the 1 gig in slot two I get it to boot and it only recognizes the 1 gig slot. Even with belarc it shows only slot one with 1042.
Sys TOSHIBA Satellite A105 PSAA2U-01T018B
Enclosure Type: Other Processor a Main Circuit Board b 1.60 gigahertz Intel Celeron M
64 kilobyte primary memory cache
1024 kilobyte secondary memory cache
Not hyper-threaded Board: ATI SB450 Rev0.4b
Bus Clock: 100 megahertz
BIOS: Phoenix Technologies LTD 2.30 09/30/08 Drives Memory Modules c,d 59.75 Gigabytes Usable Hard Drive Capacity
39.74 Gigabytes Hard Drive Free Space
TSSTcorp CDW/DVD TS-L462C [CD-ROM drive]
FUJITSU MHV2060BH [Hard drive] (60.01 GB) -- drive 0, SMART Status: Healthy 896 Megabytes Usable Installed Memory
Slot 'M1' has 1024 MB
Slot 'M2' is Emptytem Serial Number:
Enclosure Type: Other Processor a Main Circuit Board b 1.60 gigahertz Intel Celeron M
64 kilobyte primary memory cache
1024 kilobyte secondary memory cache
Not hyper-threaded

Satellite A105-S101
When putting in the I gig modules in each slot the laptop will not boot. When I put in the original 256 memory module in slot one and the 1 gig in slot two I get it to boot and it only recognizes the 1 gig slot.
That sort of thing is typical of incompatible modules. Turns out that unless you order your add-on memory from Toshiba or buy memory made by Kingston, you'll likely as not have that difficulty.
-Jerry

Z77MA-G45 wont boot up new system

dear folks,
I just built my PC and with the test build everything did it alright, but now when I have it installed in my case it wont boot up.
Everytime i boot you will see in the down right corner B4 / 99 / A2 then it gonna reboot. Ive tried with 1 ram in all the 4 slots but still got the same problem.
Theres no troubleshoot on the website so i cant check out what A2 means. Please help me

that is weird! starting to look like the board is faulty!
a thew other thing you could give a go : do a CMOS clear >>Clear CMOS Guide<< and plug unplug the PSU and hold the power button in for 30 seconds with the power switch turned on at the back of your PSU!

NF 750-G55 Wont boot on new build

Hi guys
OK, Just assembled my new PC in its bare bones state. I'm using tested DDR3 corsair 2x2GB 1600MHz, a brand new phenom 955 and a well used and reliable 650 watt Ernmax? PSU
I'm getting no action on start up, just the 4 blue LED lights. The CPU fan slows after a while, is this normal on this board even if it hasn't booted?
I have checked the output from HDMI DVI and VGA. Also all 4 LED's stay illuminated.
How can I check what bios edition my mobo shipped with? There is a very suspicious code that looks like the bios version on the side of the box it reads 911-7578-002
The mobo is in an empty case fastened in. It has the atx connector securely fastened, and the 4 pin power connector. I have reseated the ram a few times and the CPU once.
Any ideas welcome, as my old PC is now sold off over eBay So im desperate to get going again

CPU brand, model and speed
AMD Black Edition AMD Phenom II X4 955 / 3.2 GHz processor
Motherboard model (full marketing name, not just MS-xxxx) - >> How to identify your motherboard and BIOS version <<
nf750-g55 - The closest I can see to a sticker says "L090716177"
Memory brand, type/speed, size, number of sticks
CMX4GX3M2A1600C8 - 4GB (2x2GB) Corsair XMS3 Classic DDR3 PC3-12800 (1600), Non-ECC Unbuffered, CAS 8-8-8-24, XMP, 1.65V
Video card brand, chipset type, memory size
- N/A - (will be 2x evga 8800 gts 320mb, when the motherboard and CPU working. Both are watercooled)
Hard drive(s) brand, size, type, speed
Seagate SATA 500GB x 3 (don't have the model to hand)
Any other peripheral cards and devices
Operating system and version (including if 32 or 64bit!)
Windows 8 64, dualbooting into XP (neither installed as yet)
Power Supply Unit brand and output in watts and DC output (amps
Rails EG701AX-VE SFMA 2.0
+12v1 18A 35A
combine pw
+12v2 18A
-12v 0.8A
+5v 45A
+5v sb 2.5A
+3.3v 36A
I didn't actually realise how old my PSU was,. But it still kept stable voltages in my old overclocked PC with sli Gcards as of 2 days previous.

BIOS wont boot after install X

So I install the May drivers. Get the sound card to at least play sound. I then turn the computer off ( EVGA 680i, QX6700, 8800ultra, 2gigs PC28500,X-fi FPS Gamer Fatalty, Vista Ultimate32bit) Next day I turn it back on and it wont even go to bios. I then have to reset my whole CMOS which is annoying as hell and then it boots again. I have had to do this twice so far...which is everytime since I install this card.
Im thinking of just yanking the **bleep** card out. I got 5. to work, but when i play music sound is coming out of one speaker, DOH. All in all I wouldn't be so piss if there wasn't the bios problem. Any way to fix this? The funny part was the main reason i got this card was cause of the dri've bay console looks fetching in my black brushed aluminun TJ09 Silverstone case.

Satellite A305-S6916
tried .. every option on F8
Try this. Download a repair disc from here.
   Windows Vista Recovery Environment ISO X64 version (64 bit)
If you can reach the Recovery Environment by booting that, try the Startup Repair and let us know what happens. Sometimes you need to run it more than once.
   Startup Repair: frequently asked questions
Also try a System Restore.
   What are the system recovery options in Windows Vista?
-Jerry

Macbook wont boot from new hard drive.

I installed a new Western Digital 500GB hard drive into my Macbook Pro (2006 edition). The computer boots up, but it just stays at the screen with the apple and the thing circling underneath it. It won't go any further than that. I have to boot from my external hard drive to get to the Operating System.
Also it won't shut down nor restart unless I hold down the power button.
I installed Snow Leopard 10.6 on the new hard drive. The longest I waited was like 10 minutes. Should also note that there is a CD stuck in my CD/DVD optical drive (I used an external drive to install snow leopard)...I don't know if that's interfering. It didn't interfere with my old hard drive.
I've also used Disk Utility. It says the disk needs repairing, so I repair it, and it says successfully repaired, but I can't shut down or restart the computer, so I have to shut it down by holding the power button. When I turn it back on, it says it needs repairing again. Maybe it's not saving because of the improper shut down?
Please help

Welcome to Apple Discussions!
Did you format the new drive before trying to install the OS?
http://discussions.apple.com/thread.jspa?threadID=1885474&tstart=60
Try that, and if still no joy, you might have a defective drive. If so, WD will replace it under warranty.
Good luck!

975x wont boot - new parts

Hi all, im new to this forum but it seems great, i read around abit and found some useful posts.
However, i have the following setup :
Msi 975x
c2d 6400
2gb corsair xms 6400 c4 ( 2*1gb )
7900gs PoV
Aspire 550 psu
I just put the parts toghether again, after having the parts returned to vendor, he claims the first cpu didnt work, and returned the motherboard while i waited for a new cpu to arrive. When i got it i tried the system again, but the following error is still there ;
The system wont boot, other than the fans will spin up but no screen at all, just stands there, when i use the usb led thingy, it shows 4 red dots.
I saw some posts about OCZ memory that wont work, but those were reported as memory issues by the led if im correct, and as i can see it arent 4 red dots the code for CPU , or can the code be wrong and its still the memory ?
The new cpu i got was in an unopened box so it was really new, but i refuse to believe i have broken 2 cpus or have recieved 2 dead cpu from vendor.
Any ideas would be very much welcome.
Cheers // Baboon

Baboon,
You're not the only one surprised.
I bought THREE 975X PUEs and every time I have re-visited the MSI website I have found new caveats for something the board won't do, or for something that won't work, or for something not included . . . no fixes, mind you, just oddly worded "escape clauses".
Here are some examples:
MSI Reminds You...
• DDR2 800 needs to work with Intel Conroe CPU with FSB1066.
• The default memory frequency is DDR2 667, you can set to 800 in BIOS settings.
• Due to the BIOS limits, the Intel RAID and the JMicron RAID functions can not be enabled at the same time, which will cause the system unable to boot up.
• The RAID setup floppy disk is optional depending on the districts. You can download the files from the website to make the setup disk.
• To enhance IDE transfer speed, you may install JMicron IDE/SATA Driver. You may download the driver by clicking the "Driver" icon at the left side.
• The floppy disk cable will be optional.
Yep, the first one was a big surprise to a lot of us sticking in our P4s. Hello? Well, OK, maybe the "CPU Support Chart" should have been the "CPU Semi-Support Chart".
OK, I'll even give MSI the first one. But the third bullet! Now that one just flat makes me laugh!
Beta Board! MSI didn't design this Board, it just kinda "happened".

MOVED: HELP PC wont boot up after bios flash

This topic has been moved to Older MSI motherboards.
https://forum-en.msi.com/index.php?topic=184216.0

bump removed, >>Please read and comply with the Forum Rules.<<
Quote
I downloaded a newer version of the bios made a bootable usb and flashed the bios all went ok than i restarted the pc and now it wont boot and I clear my Cmos it didnt helped me .. Changed Ram slots alternatively .. didnt help
have you removed power cord from the PSU before do >>Clear CMOS Guide<< ?
Quote
MEM: 2gb RAM DD2
what memory stick exactly? brand, model
is it 1 memory stick or 2?

K9N Diamond - Wont boot after BIOS update

Just attempted to update the BIOS on my PC and it now wont boot. Used LiveUpdate with the Windows flash option (don't have FD drive). The lights on the D-Bracket 2 get as far as LED 2 Green, 1,3,4 Red. I have already tried to Clear CMOS with no joy.
Any suggestions on how to proceed much appreciated - and yes, I already know, I've probably done something stupid
Thanks
Grant.

Quote from: BOSSKILLER on 25-March-07, 19:22:15
power down PC, remove power cord from the PSU, push several times power button to drain capacitors, then Clear CMOS and leave only one memory stick into DIMM slot close to CPU socket. pull back power cord and try to boot.
in a future do not update the BIOS for no reason....(only becouse its new, only becouse new BIOS maybe got a new logo and e.g...)
Looks like I'm back in business now. I found similar instructions at this location http://www.bosamar.com/K9N/trouble.html and followed the First Procedure.
Booted ok with one mem stick, in bios fail safe mode. I counted 7 short beeps while booting then one long beep. Not sure if this is ok. Read about bios beeps here https://forum-en.msi.com/index.php?topic=82221.0 and the final long beep seems to indicate a pass???. Anyway, Vista appeared to come up ok and I checked everything in the hardware device manager and all looked fine.
Proceed to reboot with all mem sticks back in place, again same beeps but Vista coming up ok.
Next I switched bios to optimized defaults, but now 6 short beeps - no long beep. Windows looks ok. 6 beeps appear to indicate a keyboard problem, but kbd seems to work fine???
System looks ok now, but not sure if i should look into those beeps a bit more? BIOS now at 1.3, should I leave as is or revert to an earlier revision?
One thing I know that I am going to do is to install the FD drive from my old PC
Thanks for all the help.
BTW, the reason I did the BIOS flash was as a last resort to get my sound to work. Tried the various creative driver as suggest elsewhere on this forum but without success (as of yet there is no official vista compatible audio driver for my mb from MSI). The JAUD1 connector looks to be connected as specified in manual (but no audio from either the front nor real panel audio connectors).

Installed new memory and Macbook Pro wont start.

I bought a total of 8GB from PNY for my mid 2009 MacBook Pro (2.8GHz Intel Core 2 Duo). I installed it and my macbook wont turn on. When I press the power button it just beeps. The LCD doesnt turn on. I reinstalled it a few times to make sure that it is sitting correctly with no luck. I reinstalled my old memory (2x2gb) and it works fine.
The new memory I bought is PNY 8GB (2x 4GB) Bual Channel DDR3 PC3-10666. The package says that it is compatiable with 1333MHz and 1066MHz. This is the listed memory on the PNY website for Mac laptops.
Am I using the worng type of memory? I'm pretty sure my MacBook Pro can take 8GB...right?
THANKS!

One beep indicates no RAM installed. See http://support.apple.com/kb/HT1547.
What happens when you reinstall the old original memory? Does the computer boot then?
You might want to read the information at macsales.com (OWC). Certain models had to be updated to take additional memory.
Specifically the NOTE: on this page: http://eshop.macsales.com/shop/memory/Apple_MacBook_MacBook_Pro/Upgrade/DDR3

After v1.90 BIOS update Satellite Pro A300-1EA wont boot up

I have just upgraded my laptop to the new BIOS as stated in the title but after doing it my computer now wont boot up at all. I just get a blue screen with it asking me to do a CHKDSK because there might be a virus or that the hard drive isn't connected properly (when it is), and it just keeps rebooting.
It wont start in safe mode either. Anyone else had the same problem and if so, how do I get my laptop back?? :(
Thanks for any replies.

Please don't be mad on me but I think you really didn't read users manuals you got with your notebook. There is exactly described how you can have factory settings again.
So, now you are 100% sure that recovery image is not on the HDD but you don't know how to have factory settings again. Strange.
Remove battery, connect AC adapter only and disconnect all attached external devices.
Start your notebook and enter BIOS settings. Set it to default settings and try to start OS again.
What happen exactly?

New board wont boot, help please

Hi.
I have just bought MSI K9A2 Platinum with a quad core phenom 9950 black edition cpu. and ati 4850 pcs 1GB gddr3 pci-e 2x 2BG corsair ram.
I built the rig but when i push the power button everything seems to work, fans spin, cpu warms up graphics card warms up (the heatsinks) but the monitor says no signal.
Sometimes the monitor goes into standby and other times it stays on but with no picture.
Has anyone come across this problem and does anyone have any ideas why this is happening?
I have cleared bios, unplugged all usb pins etc. tried with 1 mem stick and 2 , and un plugged hard drives.
Many thanks for any help.

Thanks for all the suggestions.
The board is now booting. one of the memory sticks is dead, wont boot with it in, take it out and its fine
The problem i am having now is i cannot create an array.
in the create an array options, option 1,2,3 don't do anything but 4 does.
I managed to format the drive and the OS is loading as i type, but when pc boots it says no array created, so if I am getting the Sata speed right, if an array isn't created then it wont be running at full speed.
Ive tried changing bios setting in sata control bit... IDE, Raid and a....... cannot remember other options, but none of them work.
OS is now up and running, everything seems to be working. just strange that it wont allow me to make an array.
Any ideas thanks

Satellite A105-S2001 wont boot after memory upgrade

I just tried to upgrade my memory from 512mb to 2 gb using 2 1gb memory chips from crucial. When i insert both memory chips at the same time my laptop wont boot, it'll attempt to but stop in the middle of the process and try again 5 or 6 times. Nothin shows up on the screen. The same thing happens when i put only one 1gb chip in. When i put my old 512mb chip in and one 1gb chip the computer boots but only recognizes 960mb or ram. i also updated my bios.
thanks

Sounds like incompatible memory. Fortunately, Crucial is very good about honoring their compatibility guarantee so you should be able to get them exchanged. You can get very strange results with incompatible chips due to the differences in timing specs. That would account for what you're seeing. I assume it works normally if you have just the original 512MB chip in place.

New Neo 4 Platinum Wont boot past WIN XP :(

Hi, Im hoping someone can help me, I just built my system, its
MSI K8N Neo4 Platinum
AMD 64 3200+ 939 0.09
2 x PC4000 Crucial Ballistix (running at 200mhz)
4 Lighted Fans, Lighted case,
DVD RW, CD ROM ,
Floppy with Multimedia,
XFX Geforce 6600GT 128mb
Antec Trupower 430w 26a on the 12V, 36A on the +5V and 28A on the +3.3V
Ok, Everything works fine, till WINDOWS boots up ... And it wont boot, before the windows XP loading screen, it stays black, and freezes.. now.. to me it seems like memory/ power supply issue. lowered timings, raised Memory to 2.8v (Crucial suggest this voltage for the ram) ... no go... now my power supply is a good power supply.. but its only 20pin, and the nforce 4 ultra (well MSI) is 24pins ATX 2.0.. mine is a standard ATX12V... its supposed to still work, but Ive had mixed bagss of peopel saying it worked for them, and others that said it didnt.. but with this power supply, shouldnt I have been fine.. PLEASE someone help me, this is eating me alive...

Oh man this sounds familiar., i'm having some of the same probs. I just redid the install of XP Pro sp2 cause i needed the nvidia raid drivers for the NCQ on the Seagate i got.
The first install went fine but i couldn't oc more then 220fsb with this Corsair pc4400, so
i was like ok let's just get everything running sweet and then play. So after i added the
printer a usb scanner and a usb memcard reader for the camera, it would just hang after the boot logo for xp then it would hang on the Platinum screen sometimes too.
So i played with the voltages which seemed to help for a little bit., i went 3.3%+ on the cpu, 1.5 on the north bridge, and 2.70 on the mem. So i reformatted and used the 6.39 chipset drivers and the latest vid drivers from the manufacturer and everything seemed ok. So i proceeded to add the printer, scanner and card reader again 1 at a time and it seems like it's after the mobo gets warmed up is when it hangs on booting XP after the bootscreen., Cpu temps are at 35C and this mobo in a Cooler Master Cavalier case runs kinda warm for me like at 36 - 37C (According to Cool n Quiet) after it gets all warmed up. So i'm kinda at a loss here too. I got the same psu as the first poster. Memtest 86 ran for 4hrs, with no errors, and Sandra burned in for a couple hours with no problems.
Oh and the mobo say's the bios is the 1.1 dated 1-12-2005
So i'm hoping it's a bois thing that will be resolved soon, or is it this psu. Seems like some other fellas have had no probs with lesser psu's. Oh and do those 20 to 24 pin adapters make a difference?

MSI GT628(-455NL) new memory, doesn't boot

Hi there,
I have a MSI GT628 Gaming Notebook, and 2 days ago I decided to upgrade the RAM modules, because I need more memory for school (need to run multiple virtual machines at the same time on my laptop).
The stock memory is 4GB = 2x2GB Samsung SO-DIMMs, DDR3 PC3-8500 running at 1333MHz and 1,5V (also confirmed with CPU-Z)
2 days ago I bought 2 new SO-DIMMs, 2x8GB Kingston ValueRAM DDR3 PC3-12800 1600MHz 1,5V (CL11)
Normally if you buy faster memory in the same class it should crank it down to 1333MHz and msot of the tiem work normally, but I can't boot up my laptop with this new memory.
When I start my laptop, you hear the fan blowing for a second, then it stays on black screen with only the pwoer light on and scroll-lock light.
I've tested both 8GB modules oen by one seperately, on both slots. With only 1 of them installed it's the same. With the second one seperately it's also the same, and also tested on the other memory slot.
It keeps booting into black screen.
When I put the old stock memory back in, it works instantly, so the sltos are fully working.
With 1 of the old sticks and 1 of the 8GB, it also doesn't work. Same result.
I've reset my BIOS to factory defaults (via the BIOS menu) with the stock modules in, turned my laptop off, and put in the new RAM. Still the same result.
Does anyone have an idea what's wrong?
Can't my laptop run PC12800 modules and should I really buy PC-8500 ?
Maybe a BIOS jumper reset/CMOS battery reset would do the trick?
Thanks in advance,
-Wicked Vibez

New RAM specs:
Part Number: KVR16S11/8
Specs: DDR3, 1600MHz, Non-ECC, CL11, 1.5V, Unbuffered, SODIMM, 204-pin,
MSI GT-628-455NL specs:
Algemeen
   Merk    MSI
   Productnaam    GT628-455NL
   Productcode    GT628-455NL
   EAN code    4719072134624
   Toegevoegd op    dinsdag 13 oktober 2009
   Apparaat type    Zoek producten op basis van specificatie
   Apparaat type    Laptop
   Processor / Chipset / Geheugen    Zoek producten op basis van specificatie
   Processor serie    Intel Core 2 Duo
   Processor type    Intel Core 2 Duo P8700
   Processor klokfrequentie    2,53 GHz
   Chipset    Intel PM45
   Geheugen capaciteit    4 GB
   Type geheugen    DDR3
   Geheugen klokfrequentie    1.066 MHz
   SODIMM sloten    2
   Geheugen uitbreidbaar tot    4 GB
   Scherm    Zoek producten op basis van specificatie
   Scherm diagonaal    15,4 inch
   Resolutie    1680x1050
   Scherm type (mat/glans)    glanzend
   Graphics    Zoek producten op basis van specificatie
   GPU type    Nvidia GeForce GTS 160M
   Geïntegreerde / losse GPU    Losse chip
   Videogeheugen    1.024 MB
   Opslag    Zoek producten op basis van specificatie
   Totale opslagcapaciteit    500 GB
   Harddisk toerental    5.400 rpm
   Harddisk/SSD 1 soort    Harde schijf
   DVD branden    Ja
   Connectiviteit / Netwerk    Zoek producten op basis van specificatie
   LAN snelheid    1.000 Mbit/s
   WLAN / WiFi standaard    802.11n
   Modem    Ja
   Bluetooth    Ja
   Bluetooth-versie    Bluetooth 2.0 + EDR
   Infrarood    Nee
   3G (HSDPA/UMTS)    Nee
   Aansluitingen    Zoek producten op basis van specificatie
   PC-Card Type II    0
   Smartcard    Nee
   USB 2.0    2
   FireWire - Totaal    1
   eSATA    1
   Cardreader - SD    Ja
   Cardreader - MS    Ja
   Cardreader - XD    Ja
   TV-uitgang    Nee
   DVI-uitgang    Nee
   VGA-uitgang    Ja
   HDMI-uitgang    Ja
   Aansluiting dockingstation    Nee
   Camera    Zoek producten op basis van specificatie
   Ingebouwde camera    Ja
   Camera resolutie    2 MPixel
   Overige hardware    Zoek producten op basis van specificatie
   Geïntegreerde microfoon    Ja
   Maten en gewichten    Zoek producten op basis van specificatie
   Gewicht incl. accu    2.700 gram
   Afmeting - Breedte    35,8 cm
   Afmeting - Diepte    26 cm
   Afmeting - Hoogte    3,1 cm
   Software    Zoek producten op basis van specificatie
   Besturingssysteem    Microsoft Windows 7 Home Premium
   Besturingssysteem (serie)    Microsoft Windows

Bios wont boot up new memory

Similar Messages

Maybe you are looking for