Black screen after P35 NEO-F BIOS Flash to v2.1

Hey Out There
I just upgraded my motherboard P35 Neo-F to bios version 2.1. With the tool from this forum.
After that the PC shows a black screen when booted, I have then tryed to clear the CMOS by removing the battery and switching the jumpers place.
After that i booted, and came up with wrong CMOS. F1 to run setup, F2 to load defaults CMOS settings. I then pressed F2 and booted into Windows.
I then found out that my 3Ghz processor was only running at 2Ghz. I then rebooted to check the bios settings, but it only shows a black screen when it tryes to boot.
I have to clear the CMOS to get into windows...
What could be wrong???
Hope one out there can help me.
Regards
Rantzaus

Quote from: Rantzaus on 07-October-11, 13:21:21
Hey.
Sorry for that.. I will then flash my bios back to 1.A..
But since it is that way that P35 Neo-F uses the bios from G33 Neo-F it should go wrong a lot of times. I dont know how many of the P35 Neo-F users that knows that.
MSI should make a discription on the P35 Neo-F site, that tells: PCB rev.x uses bios xxxx and so on.
But thanks for the help.
So far arround 10 users/cases crashed to the same.
Quote
But since it is that way that P35 Neo-F uses the bios from G33 Neo-F it should go wrong a lot of times. I dont know how many of the P35 Neo-F users that knows that.
Not a lot as 2.xx BIOSes are normally not available for manual download, but only from "Live Update"
Quote
MSI should make a discription on the P35 Neo-F site, that tells: PCB rev.x uses bios xxxx and so on.
I notice them many times, but they don't listen

Similar Messages

Black screen after BIOS update

Hi there,
After updating BIOS with regular HP software (i forgot the name now), the computer shut down and from that moment when i turn it on the screen stays black (with computer apparently running). I read so many posts with similar problems and i tried few things but without success. I know that i am very close to solve the problem but from all the suggestions i am now simply confused. I would like to ask, if someone can guide me through step-by-step procedure, i figured out that i need to install a BIOS version on USB-stick, but exact details i am obviously missing.
I have HP Pavilion dv 6700 Entertainment PC and new HDD inside without HP_TOOLS on it.
Thank you veeeeeryyyy much!

Hello @milence,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that your computer is experiencing a black screen after updating the BIOS, and I would be happy to assist you in this matter!
To return the BIOS back to factory default settings, I recommend following the steps in this document on Restoring the BIOS. If the issue persists, please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

M5400 - Black screen after updating BIOS

As the title says, I've got this unwanted black screen after updating BIOS with update utility from here http://support.lenovo.com/us/en/downloads/ds037429
What I've tried :
- power / battery out, pressing power button several times for short / long and longer time
- BIOS battery out for about half an hour
- wincrisis with USB bootable stick and BIOS extracted from BIOS update utility from support.lenovo
- different combinations of keys such as : FN + B / F / R +/- win key
What should I do next except finding a hammer ?

Hey,
I am having the same problem, I was updating my bios.. followed all directions which is necessary to update them.
And then when it was almost ready it said "Bios update is not responding" so I waited... and waited because I did not want to abort it but then Vista aborted it for me.
Well at first it did not seem to be a problem but then I noticed that I could not click anything (was still in windows @ that time did not reboot yet) then I wanted to reboot but nothing worked.. Pressing off button for a time to shut down did not work.. So eventually power was out. And it shut down.
So I hooked it up again but nothing happened. Pressing the "on" button made it start.. The DVD-drive loaded for a second but... that is it just a black screen :S
Going to bring it back to the shop tomorrow.
Suxors

GTX670 - Signal lost/black screen after windows loading icon

Hello,
I hope I am posting this in the correct forum area. If not I do apologize.
Here are my specs:
Board: MSI Z97-G45 Gaming
Bios: ?? whatever pre-installed on mobo
VGA: MSI GTX670 OC
PSU: Corsair HX750 750W
Intel Core i7-4790K
MEM: 12 GB Kingston HyperX DDR3 1600 2x 4GB, 2x 2GB sticks
HDD: SSD Kingston 120 GB (Win7), HDD 1 TB WD 7200 RPM (Win7), HDD 1.5 TB WD 7200 RPM (storage)
COOLER: Corsair Hydro Series H60 Water Cooler
OC: no overclocking done by me..default settings
OS: Windows 7 64bit Professional
So to keep this as direct and as short as humanly possible here is my situation.
Had a gtx670 card that I had to send back to MSI under RMA. They sent me what looks like a new gtx670 card (no dust) that I received yesterday (4 Aug). Last night I removed temporary old card (9800gt) and plugged in new 670gtx. Things seemed to be ok, reinstalled driver after card was recognized. Played one round of Battlefield 4 for testing purposes and all seemed good.
Upon exiting the game things went south in a hurry. Moving the mouse cursor around was extremely slow and choppy. Mouse clicks were not recognized. I could not bring up ctrl-alt-del to get to task manager. At this point the cursor turned to spinning circle as if things were happening. However, after 5+ minutes of nothing changing I did a hard boot.
Restarted and after the windows loading screen the signal appeared to be lost to the monitor and I was left with black screen. This was with the SSD. I then attempted to load into the HDD windows OS that I hadn't logged into yet with this card and was greeted with the same issue.
I can load into Safe Mode with no issues. In safe mode I removed all nvidia drivers and was then able to load into windows normally using basic windows vga drivers. The moment I load the Nvidia drivers and restart the computer I then have the issue again. This happens with both drives.
I have reset the video card in the PCI-Ex16 slot and still received the problem. I have tried a different PCI-Ex16 slot and still had the issue. I put the old 9800gt card back in and windows loaded perfectly and without issues on both drives. I put the 670gt in and try to load into normal windows and I lose signal and get black screen after the windows loading screen.
I'm at a loss at the moment. I think it's the drivers, but could it be the card?
Doing some research I've come across some people saying there may be issues with the nvidia HD audio drivers that are installed with the video drivers. Could it be as simple as uninstalling or unchecking that particular driver?

Flashed the BIOS last night to the latest version and attempted to launch windows with the GTX670 card. I still experienced the same issue where as soon as windows finishes it's loading animation (with Nvidia drivers) and it goes to the login screen, the monitors cut out.
At this point I feel like it has to be the card. The moment I install the video drivers and restart, I have the problem of losing the signal/black screen.
What I have done:
1) Completely wiped any/all video related drivers from the computer and started from scratch. No success.
2) Ran Memtestx86 to see if it's a problem with my memory sticks. No problems found.
3) Put the card in a different PCI-Ex16 slot to see if there was a problem with the slot. No success.
4) Flash updated the BIOS on the motherboard to the latest version. No success.
I have a dual boot computer with Windows 7 64-bit installed on an SSD and a HDD. The problem happens on both drives. Yet, the moment I install my old 9800GT the problem disappears and I can login to Windows just fine.
I will be sending the card back today on another RMA.

MSI R9 270X - Black Screen after Win7 logo

Hello there.
About a week ago I upgraded my PC, buying several components and putting it to work. Here's the specs.
Main Board: M5A97 EVO R2.0
Bios Version: Latest
Video Card: MSI Radeon R9 270X TwinFrozr OC Edition 2Gb
PSU: Don't know
12v rail Rating of listed PSU:
CPU: AMD FX 8350 4.0Ggz BE SkAM3+
Memory: 8Gb Crucial Ballistix DDR3-1600Mhz
SSD/ HDD: Western Digital WD10EZRX-00A8LB0 1TB
CPU COOLER: The one that came with the CPU
Raid Card: Onboard
Sound Card: Onboard
OC: (Yes / No) Don't know
Operating System: Win 7 SP 1 64
So, it worked just fine for about 3 days. Last Saturday night I tried to open Google Chrome after some gaming and the the system froze. I got a screen with vertical black and white stripes. I had to reboot the system and it gave me a black screen, crashing again, after the Win Logo at start up. At this time I was running either 14.7 or 14.9 ATI drivers.
I could only start the PC on Safe Mode. Removing the drivers and getting Windows general VGA card settings would allow me to use Windows in normal mode though. Once I installed the Graphic Card's drivers it crashed on reboot, always with the black screen after Win logo. I installed several ATI drivers, namelly 14.9, 14.11 beta, 13.12... and nothing worked.
I flashed the Mother Board BIOS to the latest version, formatted the HDD doing a fresh install of Win 7, installed Catalyst first and then the drivers, the drivers without catalyst, etc. and nothing worked, always getting a black sreen on reboot once the Graphic Card's drivers were installed. I even swapped the Graphic Card to a different slot to no avail.
Right now I'm using my old Radeon HD 5670 with the latest drivers and everything works just fine. It even works fine if I keep both Graphic Cards installed with the monitor plugged to the older card. I find this odd since to do so, Windows loads both cards drivers with no errors. But once I switch to the new card everything goes black.
Can someone help me out? I've tried to contact my vendor's technical support through mail but they're not answering. I fear that I'll have to report it as DOA and swap it out, which will take quite some time taking into consideration the way things tend to work around here.
EDIT - I don't have a 2nd system to test it on.

Nope. Not driver issue at all. I tested at least 3 different drivers, all with the same result. Besides, I used both Driver Fusion and Driver Cleaner and CClean to remove any non-deleted registry entries. Always got the same problem. Went as far as formating the drive and doing a clean Win install. The problem persisted.
Tried installing drivers without Catalyst to no avail. Tried installing Cataltst first and then the drivers. Nothing. It always crashed omce the drivers were installed.

270X Gaming - Black screen after driver install

I just recently purchased an MSI R9 270X Twin Frozr Gaming.
I physically installed the board and booted my PC. Windows started fine, albeit in VGA mode. I then proceeded to install the latest AMD drivers for the card (13.11 Beta). I made it through installation and then rebooted. When I rebooted, I got a blank, black screen after the "Starting Windows" screen. I was unable to boot windows, so I restored to last known configuration and tried again with different drivers (13.9) with the same result.
Does anyone know why windows hangs when it loads the display driver? Any help would be much appreciated.
Thanks
Windows 7 x64 SP1 (fresh install)
ASRock Z77 Extreme4
Core-i5 3570K (no overclock)
4x4GB Corsair Vengeance (stock profile)
Rosewill CAPSTONE 550W ([email protected])
MSI R9 270X Twin Frozr Gaming (S/N 602-V303-03SB1309077057)

Hi everyone. I just wanted to give you an update. It seems I have resolved the problem.
After attempting other fixes (fresh Windows install, MB BIOS update, etc), flashing the BIOS of the video card fixed the problem. I used the BIOS version
015.040.000.000.002887. I believe the BIOS the card shipped with is 015.039.000.000.002887. Anyway, there are no problems now. I was able to install Catalyst 13.11 Beta 9.5 with no problems and no black screens.
I got the BIOS and ATIWinflash from TechPowerUp. I'd post links, but I am too new to the board.
Thanks guys.

Lenovo G560 - Issue with won't boot and black screen after HDD upgrade

Lenovo G560 - Issue with won't boot and black screen after HDD upgrade.
What happen: My laptop was working fine, no blue screen issue, no funny business at all. I bought a new SSD Intel 120 GB and thought it would be a good idea to replace the HDD. I shutdown and disconnected the power adapter, waited a couple of minutes and removed the battery. I opened up the back case and replaced the HDD. And put all the screws back and put the battery back in.
Problem: The very first time I turned the power on, nothing happens besides a black screen. I pressed the dvd drive it works and opens up and closes. I waited for about 30 mins and still has blac screen. When I mean black screen, no bios menu, no logo, just a black screen with the fan sound on.
I have tried these:
1. Unplugged everything - battery, adapter, and pressed the power on button for about 60 seconds, nothing, the laptop turns on with the LED display on for both on and battery LED's. But nothing but black screen, no sound of windows loading just the fan and black screen.
2. I tried putting back my old 2.5" and nothing but black screen.
Thoughts and suggestions?
Solved!
Go to Solution.

Hi Autoexit173,
Welcome to Lenovo Community!
As per the query we understood that you are facing issue with system not booting in your Lenovo G560 laptop.
As you have mentioned that the system not booting, please try to remove the RAM and turn on the system and check if you can hear any beep sound. Also try to clean the RAM slots and check for the issue.
Click here for the steps to remove the RAM and refer page number 40.
Hope this helps. Do post back if issue persists!
Best regards,
Ashwin.S
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Qosmio X870-149 - Black screen after Update to win 8.1

After an update to win 8.1 I got a black screen after login , the only thing I could do was to press zero during startup and make a recovery installation .
It took 40 houres , I do not know why it took so long , but when it was over, the HDD was completely empty , so I installed win 7 instead , since I had not made ??a recovery CD . The problem now is that I still get black screen in between , and thinking that it might be a heat problem , I still have warranty , but I do not know if it applies when I installed win 7 on the machine.
I still have a warranty on my toshiba Qosmio

Hi
Well, the warranty covers the hardware related problems. It does not cover any issues related to the software.
Now the open question is: why the black screen appears?
Is it hardware or software issue?
What happens if you access the BIOS?
Can you see anything on the screen?
Is something visible on the external monitor?

WINDOWS 8 BLACK SCREEN AFTER LOGIN PROBLEM

Please help me i have a problem with my computer it goes black screen after i login
my desktop is hp pavilion a5055d my os is windows 8 i dont know what the problem
i have a ati radeon xpress 1100 for videocard ..
I tried to restart many times.

Hi,
Did this issue occur before?
Try to logon with Safe Mode to see if the same issue occurs.
Furthermore, you can try to update BIOS for your machine?
You can refer these article to update BIOS if your machine cannot boot:
http://www.ehow.com/how_7356859_update-bios-windows-won_t-boot.html
http://www.wikihow.com/Fix-a-PC-Which-Won't-Boot
Hope that helps.
Leo Huang
TechNet Community Support

Black Screen After Upgrading to Windows 8

Hi
I'm experiencing a black screen after upgrading a Dell N5050 B890 to Windows 8.
Tried to refresh the installation but the problem persited. re-installed the Windows 8, the machine logged in successfully but the problem arose again after reboot.
Urgent assistance needed

This problem is solved...
I guess the problem is concerned with the display module controller in the BIOS which is having a slight compatibility issue with windows 8.
This issue is solved by updating the BIOS of your Laptop/PC to the latest version. You can download the latest BIOS from the website of the Laptop company/Motherboard Company.
But for updating the BIOS, you have to start your computer/Laptop for at least one time in Normal Mode. So here are the steps to do so...
1) Boot the Laptop/PC.
2) After the boot screen (The Circle Animation & Windows 8 logo), you will be presented by the lovely & awesome blank screen.
3) Wait for 1 minute so that drivers load into the memory.
4) Press the Power button of your laptop/PC for only a moment (Just Press and release it quickly. Don't hold. We don't want to shut down).
5) This will force the laptop/PC to go into Sleep mode.
6) When the laptop/PC goes in sleep, the laptop fan & other sounds will stop.
7) After 4-5 seconds, press the power button again & release it quickly.
8) Voilllaa!!! The laptop/PC starts & you are presented with the lock screen. Now..... Login! What are you waiting for! :P
This is not the permanent solution. It just lets you start you Laptop/PC.
After updating the BIOS, I strongly suggest that you must download the latest graphics driver for your Computer/Laptop to avoid any further issues.

IOS adhoc displays black screen after launch

Hi,
my iOS application displays black screen after slash screen.nothing happens and couldn't see any proper errors on debug utility.
I can build adhoc using flash builder and it's works fine but problem occurs when I create ipa using dumped config file on command line(ant)
I'm using flex sdk 4.6 and AirSDK 15.0(overladed) .my application includes few native extensions.
mxmlc
mxmlc -load-config app-config.xml src/mobapp.mxml -output myapp.swf
adt
<target name="build-release-adhoc-package-ipa">
    <echo>::building captive-runtime release-adhoc ipa..</echo>
    <exec executable="${FLEX_BIN}/adt" failonerror="true">
        <arg line="-package" />
        <arg line="-target ipa-ad-hoc" />
        <arg line="-storetype pkcs12" />
        <arg line="-keystore ${provision.dir}/release-adhoc.p12" />
        <arg line="-storepass 12345" />
        <arg line="-provisioning-profile ${provision.dir}/release_adhoc.mobileprovision" />
        <arg line="${adhoc.dir}/ios-adhoc.ipa" />
        <arg line="${src}/mobapp-app.xml" />
        <arg line="myapp.swf" />
        <arg line="${icon.dir}/applicationIcon16.png" />
        <arg line="${icon.dir}/applicationIcon32.png" />
        <arg line="${icon.dir}/applicationIcon36.png" />
        <arg line="${icon.dir}/applicationIcon48.png" />
        <arg line="${icon.dir}/applicationIcon57.png" />
        <arg line="${icon.dir}/applicationIcon72.png" />
        <arg line="${icon.dir}/applicationIcon76.png" />
        <arg line="${icon.dir}/applicationIcon114.png" />
        <arg line="${icon.dir}/applicationIcon120.png" />
        <arg line="${icon.dir}/applicationIcon128.png" />
        <arg line="${icon.dir}/applicationIcon152.png" />
        <arg line="${base.dir}/[email protected]" />
        <arg line="-extdir ${src}/ane" />
        <arg line="-platformsdk /Applications/Xcode.app/Contents/Developer/Platforms/iPhoneOS.platform/Developer/SDKs/iPh oneOS.sdk" />
    </exec>
    </target>
please help.

Hi,
my iOS application displays black screen after slash screen.nothing happens and couldn't see any proper errors on debug utility.
I can build adhoc using flash builder and it's works fine but problem occurs when I create ipa using dumped config file on command line(ant)
I'm using flex sdk 4.6 and AirSDK 15.0(overladed) .my application includes few native extensions.
mxmlc
mxmlc -load-config app-config.xml src/mobapp.mxml -output myapp.swf
adt
<target name="build-release-adhoc-package-ipa">
    <echo>::building captive-runtime release-adhoc ipa..</echo>
    <exec executable="${FLEX_BIN}/adt" failonerror="true">
        <arg line="-package" />
        <arg line="-target ipa-ad-hoc" />
        <arg line="-storetype pkcs12" />
        <arg line="-keystore ${provision.dir}/release-adhoc.p12" />
        <arg line="-storepass 12345" />
        <arg line="-provisioning-profile ${provision.dir}/release_adhoc.mobileprovision" />
        <arg line="${adhoc.dir}/ios-adhoc.ipa" />
        <arg line="${src}/mobapp-app.xml" />
        <arg line="myapp.swf" />
        <arg line="${icon.dir}/applicationIcon16.png" />
        <arg line="${icon.dir}/applicationIcon32.png" />
        <arg line="${icon.dir}/applicationIcon36.png" />
        <arg line="${icon.dir}/applicationIcon48.png" />
        <arg line="${icon.dir}/applicationIcon57.png" />
        <arg line="${icon.dir}/applicationIcon72.png" />
        <arg line="${icon.dir}/applicationIcon76.png" />
        <arg line="${icon.dir}/applicationIcon114.png" />
        <arg line="${icon.dir}/applicationIcon120.png" />
        <arg line="${icon.dir}/applicationIcon128.png" />
        <arg line="${icon.dir}/applicationIcon152.png" />
        <arg line="${base.dir}/[email protected]" />
        <arg line="-extdir ${src}/ane" />
        <arg line="-platformsdk /Applications/Xcode.app/Contents/Developer/Platforms/iPhoneOS.platform/Developer/SDKs/iPh oneOS.sdk" />
    </exec>
    </target>
please help.

HP Pavilion DV3 41700-EE Problem-Black Screen after installing graphic card driver

Hi,
Laptop Model : HP Pavilion DV3 41700-EE Entertainment series.
I download the latest official driver for my lap top from this link : http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-93326-1&cc=us&dlc=en&lc=en&...
After the installation i rebooted my device and after the windows loading i got a black screen ! i went to safe mode and unistall the video card and also it's driver from device manager and when i came back the black screen was gone but i have only my onboard Integ graphic which is very slow.
also i went to AMD web site and get AMD Catalyst from their web site but nothing happened after the installation and i think they don't provide an appropriate driver for my lap top.
i also tries to go to device manager and with right click on my display adapter and update driver point to the display driver location on my syste but this time it does not take time the black screen after restart, and in the middle of installation i got a black screen.
Also i upgraded my BIOS Firmware from 16 to 24, but nothing changed.
i just wanna know is it a software problem or hardware problem ? how can i find out that ?
also i don't want this switchy manner and i don't care about the power efficency. i just want to my device work on maximum performance.
What you suggest i do ?

Use the recovery manager to reinstall the original AMD graphics driver and Catalyst Control center.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

T410 & Windows 8 Pro 64bit - display black screen after wellcome screen

I'm using T410 and Windows 8 Pro 64 bit.
Sometime, when i boot start Windows, after Wellcome , the screen is black.
But when i press Ctrl+Alt+Del, its' appear Task Maneger...vv.v...... but when i try lo login, after then, it's re-appear Black Screen (with cursor)
I updated BIOS.
Display was updated by Windows 8 (not manual)
Please help me fix this issue.
Thanks !!!

Did you upgrade to Windows 8 or do a clean install?
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

Z77 mpower replaced, black screen after post.

Ok so I've loved my setup for a year solid, until the other day when my Z77 Mpower started smoking from under one of the heatspreaders. I'm all set for an RMA, but in the meantime I had to buy another Mpower board. This is my work PC, and I cannot wait the 2+ weeks for a replacement. So I bought another mobo of the same model and just got done swapping everything out. Now I get post fine, but when loading windows I just get a black screen.
I've:
Updated bios to latest
Taken out all but one stick of RAM
Tried both on-board and discreet GPU
Tried safe mode (stops at "please wait" and doesn't go any further)
Tried startup repair (black screen)
Tried reinstalling windows (freezes after "Windows is loading files..." at the "Starting Windows" screen.
My drives and such all show up fine in bios. No errors on the board. I don't hear the windows chime when trying to boot windows normally.
4 or 8gb ddr3, MSI 670GTX, mushkin 240gb SSD(boot), 640gb WD HD(data)
Please help, as this PC is my Iivelyhood and sanity.
Matt

Update: after clean memtest and trying everything under the sun including a new PSU, I've finally made a discovery. I can finally boot to OS if I enable only 1 core of the procesor. This is under CPU features of the overclock menu.
Now I'll reseat the CPU, check for bent pins, etc. If this changes nothing, do I assume that my CPU is damaged or there's something wrong with the new board? I guess the only way to know for sure is to have another CPU or board, of which I have neither at this time.

[SOLVED] Black screen after GRUB

Hello everyone
I was setting up a machine with E17 and was trying various DM's since none seemed to work. After attempting to use LightDM, I get a black screen after GRUB. I was trying to read the various logs at /var/log/ but I cannot understand them properly. I tried reinstalling entrance and LightDM with no luck. I even tried editing grub's entry appending '1' or 's' and still no dice. Any help would be appreciated.
Last edited by Linoman (2014-01-20 09:22:33)

Hi tnx for both answers.
I missed something important in Xorg.log. As you can see, fbdev and modesetting aren't loading as usual. I didn't check grub stuff, I don't think it's related, since loading in level 3 (text mode) I get a black screen but I can login as root and turn off the computer blindlessly.
[ 2.969] (II) LoadModule: "modesetting"
[ 2.969] (WW) Warning, couldn't open module modesetting
[ 2.969] (II) UnloadModule: "modesetting"
[ 2.969] (II) Unloading modesetting
[ 2.970] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 2.970] (II) LoadModule: "fbdev"
[ 2.970] (WW) Warning, couldn't open module fbdev
[ 2.970] (II) UnloadModule: "fbdev"
[ 2.970] (II) Unloading fbdev
[ 2.970] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 2.970] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
GM45, 4 Series, G45/G43, Q45/Q43, G41, B43, HD Graphics,
HD Graphics 2000, HD Graphics 3000, HD Graphics 2500,
HD Graphics 4000, HD Graphics P4000, HD Graphics 4600,
HD Graphics 5000, HD Graphics P4600/P4700, Iris(TM) Graphics 5100,
HD Graphics 4400, HD Graphics 4200, Iris(TM) Pro Graphics 5200
[ 2.970] (II) VESA: driver for VESA chipsets: vesa
[ 2.970] (++) using VT number 7
[ 2.974] (WW) Falling back to old probe method for vesa
javex wrote:Post the content of the following files:
Also does disabling LightDM again help resolve the issue, i.e. can you get it to work without LightDM?
No, I can't get it to work changing DM's. I'm not sure if I pacman -Syu before changing DM's another time. Maybe it wasn't LightDM's fault afterall.
Spider.007 wrote:Additionally; try booting without the 'quiet' entry that is in the kernel line by default; and disable https://wiki.archlinux.org/index.php/Ke … de_Setting too
Thanks for pointing out that. I didn't knew I had it on.
Last edited by Linoman (2014-01-11 21:34:08)

Black screen after P35 NEO-F BIOS Flash to v2.1

Similar Messages

Maybe you are looking for