Black screen after stuck in lenovo logo

When I was shutting my computer down, the lights and the power didn't turn off so I forced it to shutdown. The next day I tried booting it up, and I was stuck in the lenovo logo for a while. When the lenovo sign is gone the screen is.just black no log in option whatsoever. My.laptop is the lenovo u410

hi pezza1979,
Welcome to the Forums.
Your issue might be similar to this thread.
Can you try the following:
1. Follow this guide on how to enable Legacy Safe Mode
2. When done, try to boot the machine in Safe Mode. If everything's working fine on Safe Mode, perform a clean boot and observe the machine in normal mode.
If same problem, try to disable graphics switching:
3. Boot into the BIOS by pressing F2 on bootup or by pressing the OneKey Recovery button > BIOS Setup
4. In the BIOS, navigate to the Configuration Tab and set Switchable Graphics to UMA Only.
- LInk to picture
Let me know how it goes.
Regards
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Similar Messages

Lenovo G560 - Issue with won't boot and black screen after HDD upgrade

Lenovo G560 - Issue with won't boot and black screen after HDD upgrade.
What happen: My laptop was working fine, no blue screen issue, no funny business at all. I bought a new SSD Intel 120 GB and thought it would be a good idea to replace the HDD. I shutdown and disconnected the power adapter, waited a couple of minutes and removed the battery. I opened up the back case and replaced the HDD. And put all the screws back and put the battery back in.
Problem: The very first time I turned the power on, nothing happens besides a black screen. I pressed the dvd drive it works and opens up and closes. I waited for about 30 mins and still has blac screen. When I mean black screen, no bios menu, no logo, just a black screen with the fan sound on.
I have tried these:
1. Unplugged everything - battery, adapter, and pressed the power on button for about 60 seconds, nothing, the laptop turns on with the LED display on for both on and battery LED's. But nothing but black screen, no sound of windows loading just the fan and black screen.
2. I tried putting back my old 2.5" and nothing but black screen.
Thoughts and suggestions?
Solved!
Go to Solution.

Hi Autoexit173,
Welcome to Lenovo Community!
As per the query we understood that you are facing issue with system not booting in your Lenovo G560 laptop.
As you have mentioned that the system not booting, please try to remove the RAM and turn on the system and check if you can hear any beep sound. Also try to clean the RAM slots and check for the issue.
Click here for the steps to remove the RAM and refer page number 40.
Hope this helps. Do post back if issue persists!
Best regards,
Ashwin.S
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

[LENOVE G460] Stuck at Lenovo Logo Screen when a Boot-able USB plugged in

The subject says it all.
I was thinking of doing a Live Install of a Linux Distribution using a Bootable USB.
So I plugged the Boot-able USB and then Power the Laptopn ON and then press F2 to enter the BIOS SETUP
But even after a few minutes the screen doesn't even budge from the Lenovo Logo... It just says "Entering Setup..."
First I thought something was wrong with my Boot-able USB so I checked it by using another laptop and TADA!!!! I managed to enter the bios setup screen, change the boot order and then start the Linux Installation without any problem.
And then I decided to do it again on the Lenovo G460 and then... The same Stuck at The Lenovo Logo Screen happened again.
Could Anyone shed some light on this problem?
Thanks XD

Hi Warnbroom,
Welcome to Lenovo Community!
As per the query we understood that you are facing issue with system stuck at Lenovo logo in your Lenovo H500s laptop.
Try to remove the hard drive(HDD) and check for the issue if the system is able to boot to BIOS.
Hope this helps. Do post back if issue persists!
Best regards,
Ashwin.S
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

MSI R9 270X - Black Screen after Win7 logo

Hello there.
About a week ago I upgraded my PC, buying several components and putting it to work. Here's the specs.
Main Board: M5A97 EVO R2.0
Bios Version: Latest
Video Card: MSI Radeon R9 270X TwinFrozr OC Edition 2Gb
PSU: Don't know
12v rail Rating of listed PSU:
CPU: AMD FX 8350 4.0Ggz BE SkAM3+
Memory: 8Gb Crucial Ballistix DDR3-1600Mhz
SSD/ HDD: Western Digital WD10EZRX-00A8LB0 1TB
CPU COOLER: The one that came with the CPU
Raid Card: Onboard
Sound Card: Onboard
OC: (Yes / No) Don't know
Operating System: Win 7 SP 1 64
So, it worked just fine for about 3 days. Last Saturday night I tried to open Google Chrome after some gaming and the the system froze. I got a screen with vertical black and white stripes. I had to reboot the system and it gave me a black screen, crashing again, after the Win Logo at start up. At this time I was running either 14.7 or 14.9 ATI drivers.
I could only start the PC on Safe Mode. Removing the drivers and getting Windows general VGA card settings would allow me to use Windows in normal mode though. Once I installed the Graphic Card's drivers it crashed on reboot, always with the black screen after Win logo. I installed several ATI drivers, namelly 14.9, 14.11 beta, 13.12... and nothing worked.
I flashed the Mother Board BIOS to the latest version, formatted the HDD doing a fresh install of Win 7, installed Catalyst first and then the drivers, the drivers without catalyst, etc. and nothing worked, always getting a black sreen on reboot once the Graphic Card's drivers were installed. I even swapped the Graphic Card to a different slot to no avail.
Right now I'm using my old Radeon HD 5670 with the latest drivers and everything works just fine. It even works fine if I keep both Graphic Cards installed with the monitor plugged to the older card. I find this odd since to do so, Windows loads both cards drivers with no errors. But once I switch to the new card everything goes black.
Can someone help me out? I've tried to contact my vendor's technical support through mail but they're not answering. I fear that I'll have to report it as DOA and swap it out, which will take quite some time taking into consideration the way things tend to work around here.
EDIT - I don't have a 2nd system to test it on.

Nope. Not driver issue at all. I tested at least 3 different drivers, all with the same result. Besides, I used both Driver Fusion and Driver Cleaner and CClean to remove any non-deleted registry entries. Always got the same problem. Went as far as formating the drive and doing a clean Win install. The problem persisted.
Tried installing drivers without Catalyst to no avail. Tried installing Cataltst first and then the drivers. Nothing. It always crashed omce the drivers were installed.

IPhone 5s goes black screen after the Apple logo is displayed

Recently, my iPhone 5s keep restarting when I am using it and a blue screen appeared before the restart process. But worse, this time, my iPhone stays on the black screen after the apple logo is displayed and it is turned off automatically after a couple seconds, what happened and what should I do?

Hi CarltonKwok,
If the screen on your iPhone turning on completely, you may find the following article helpful:
iOS: Not responding or does not turn on
http://support.apple.com/kb/ts3281
Regards,
- Brenden

Black screen after windows logo problem

Hi people, i have the HP Probook 4530s LH306EA and i have been using it for 3 years without any problems but this week after i did a restart on my laptop i got a black screen after the windows logo.
The problem is whenever i install the AMD Display driver it says that there were some errors during the install and the pc freezes and restarts into a black screen...
AMD Display drivers 13.152-130830A-162882C(18 Oct 2013)
Windows 8.1 64bit
Is there any solution to this or some other drivers?

you wouldn't by chance be attempting to use a Sandforce controller using SSD?
please list your components >>Posting Guide<<!
See my signature below for guidance
--------------------vvvvv--------------------

IPod 4G black screen, unresponsive, stuck during restore

Hi there, I would like to know if anyone has had this problem and if it has been resolved. I've encountered myself to be stuck in this loop of "waiting for ipod" when trying to restore the ipod to ios 6.1.3. It was previously on ios 6.1.2. This is my GF's ipod and she had told me she was using it just fine, but once putting it into her bag, and checking it again the screen had gone entirely black. She'd charge it assuming it was dead but it had gone into a recovery/DFU mode loop. Everytime I plug it into my computer I receive a message that it is in recovery mode and must be restored. I remind you again that no combination of buttons will cure the screen at this point. Holding home + power button for a few seconds for a soft reset just shows the same message when plugged in. Anyway, as I try to update, the screen turns on showing the apple logo and loading bar, but then once the step gets to "waiting for ipod" nothing works. I've tried letting it sit there for over 2 hours, but nothing. I have yet to find a solution, and it's become quite frustrating. Please let me know if you have any idea how to fix this. I've tried messing around using different methods such as iRec, TinyUmbrella, Redsn0w recovery, messing with hosts files, firewall, etc.

I think you are experiencing a fake DFU mode you are always on black screen and iTunes prompt recovery mode.
I think links below can help on how to put it to proper DFU mode, avoid error 1600 and 1601 when restoring, and proper update or restore.
How to Fix: iDevice Black Screen after Update or Restore
DFU over DFU

My ipod 5th gen ios 7.0.6 crashed and keeps going from the apple logo, going to a black screen, back to the apple logo, then back to the black screen and so on. Furthermore, my laptop doesn't recognise that the iPod is connected. What do I do?

My ipod 5th gen ios 7.0.6 crashed and keeps going from the apple logo, going to a black screen, back to the apple logo, then back to the black screen and so on. Furthermore, my laptop doesn't recognise that the iPod is connected. What do I do?
Please help me out as this is very irritating. This has been happening for the last 20-30 minutes. It had roughly half battery left.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Black Screen After Upgrading to Windows 8

Hi
I'm experiencing a black screen after upgrading a Dell N5050 B890 to Windows 8.
Tried to refresh the installation but the problem persited. re-installed the Windows 8, the machine logged in successfully but the problem arose again after reboot.
Urgent assistance needed

This problem is solved...
I guess the problem is concerned with the display module controller in the BIOS which is having a slight compatibility issue with windows 8.
This issue is solved by updating the BIOS of your Laptop/PC to the latest version. You can download the latest BIOS from the website of the Laptop company/Motherboard Company.
But for updating the BIOS, you have to start your computer/Laptop for at least one time in Normal Mode. So here are the steps to do so...
1) Boot the Laptop/PC.
2) After the boot screen (The Circle Animation & Windows 8 logo), you will be presented by the lovely & awesome blank screen.
3) Wait for 1 minute so that drivers load into the memory.
4) Press the Power button of your laptop/PC for only a moment (Just Press and release it quickly. Don't hold. We don't want to shut down).
5) This will force the laptop/PC to go into Sleep mode.
6) When the laptop/PC goes in sleep, the laptop fan & other sounds will stop.
7) After 4-5 seconds, press the power button again & release it quickly.
8) Voilllaa!!! The laptop/PC starts & you are presented with the lock screen. Now..... Login! What are you waiting for! :P
This is not the permanent solution. It just lets you start you Laptop/PC.
After updating the BIOS, I strongly suggest that you must download the latest graphics driver for your Computer/Laptop to avoid any further issues.

LENOVO G50-30 stuck at lenovo logo and cant even enter bios

Hello
I yust got my lenovo G50-30 and wanted to install win 7 on it. after the first BsoD I went to bios and changed the AHCI to legacy mode. Got the same BsoD. After that I changed the Os mode from win 8 to win 7 ... loaded the factory default settings and putted from AHCI to legacy mode again.
After that the laptop turns on, but it stucks at lenovo logo. I cant access the bios anymore to make any other changes. If I insert a win7 instalation disc, it start to spin but with no sucess. also cant acess the boot options anymore.
Any help greatly apreciated

I suggest removing battery and AC, holding the power button for more than 15 seconds to reset the BIOS back to default settings then see if the issue remains.
Make sure to post the results.
Good luck.

Boot Camp Windows 7 Black Screen After Graphic Driver Installation

Hi,
I have MacBook air (2012 model i think). I tried to install windows 7 64 bit using bootcamp. On the first windows boot and before installing boot camp drivers windows was fine. After installing bootcamp drivers and windows restart the windows came up to a black screen and stuck forever. When I uninstall graphic driver (intel HD 4000), windows is good again. Tried to reinstall different graphic drivers versions - didn't work. searched internet everywhere and didn't find any solution.
please help!

I have solved this issue now but seem to have encountered another one. I solved the above issue simply by keep on trying time and time again, partitioning the hard drive and trying to install windows 7.
Anyway, I have encountered this error: windows setup could not apply the configuration set. The WINDOWS folder cannot be found.
Please help!

Black screen after Mavericks update ?

Hi everybody,
First of all, I want you to know that I'm French so I want to apologize for my potential mistakes
A few weeks ago, I updated Mavericks (because my mac told me to do that every single day .. ) on my Macbook Unibody bought in September 2010.
After that update, I had a black screen after the "Apple logo" and couldn't do anything. I went to a Genius Bar in Paris and the technician told me that the unique solution was to format the laptop. I decided to accept this because I needed my laptop for work. However, I lost all my data (documents, pictures ...)
Apparently, I'm not the only person in that case and the problem comes from Mavericks.
So I want to know if someone else is also in that case, and I think that it's unacceptable that Apple does not communicate about this.
Thank you

Connect the MBP to a monitor. If the monitor fails to produce an image, the GPU is suspect. If the monitor produces an image, the display or the display connection is faulty.
Ciao.

Black screen after startup - Satellite A105-S4334

it gives me black screen after windows logo display right after the appearance of the cursor, and nothing i can do except hold on the "Turn off" button, and then restart again, it shows the menu to whether to start in safe mode ... network mode ... normally or lastest know good windows start ....
when it starts for the second time it works fine, it does this all the time and now i'm reinstalling windows for the 2nd time (factory-state) any solution or explanation for this issue?

no, i didn't, nothing connected to it yet.
what trials i did:
i reinstalled my own windows XP and it didn't show this, but because the PowerSaver error msg. and returned back to the manufactuer state CD, and same black error occurs.
Notices:
1- when i do restart it doesn't happen
2- right away after it happens and hold on the power button till it shuts down and turn it on again, and it works fine.
3- i don't know is this has nothing to do with DVD/CD rom message comes after start up asking to disable DVD-Ram option or not? but i always answers NO
hope these info helps you helping me :)

TS3274 My ipad2 is not responding..I want to restart it but i can get nothing but a black screen with only the apple logo and a small gear icon. It occasionally beeps but no other response. Any ideas as to what may be wrong and what I can do?

My ipad2 is not responding..I want to restart it but i can get nothing but a black screen with only the apple logo and a small gear icon. It occasionally beeps but no other response. Any ideas as to what may be wrong and what I can do?

Try:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPad fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

Black Screen after computer boots to Win XP With NX6600 VTD 256

My son recently purchased a new computer and gave his old one to me to salvage what I wanted.Since he just a few months ago purchased my NX6600 VTD 256 from me I naturally salvaged that first. I tried to install the NX6600 in my other son's computer without success. First the particulars:
MSI 845 Pro2 Mobo, 512 mb 133 Mhz Ram, 1.7 Ghz Intel CPU, Aopen AO350 12A PNF power supply, 350 watts with 18 amps on the 12 volt rail.
I did a fresh install of winXP on a freshly formatted HDD. Installed service pack 2, the latest intel drivers, and 5 different versions of the driver packages including ver 77.77 all with the same results.
After the computer boots I am intermittantly faced with a black screen after the WinXP logo disappears. This sometimes happens 3 times in a row before I get a working screen. After a good boot the NX6600 benchmarks good with very good marks!
I am at this point strongly suspecting the power supply is not up to the task, even though the specs for the NX6600 recommend a 350 watt power supply. Before I start removing all the hardware from the computer except for the NX 6600 to see if I have a hardware conflict, I doubt this because with the NX6600 installed without drivers I get a good boot every time.
I'm open for suggestions.

Thanks for the reply boss killer.
I tried what you suggested with a CRS power supply 300 watts with 15 amps on the 12 volt rail.
with the exact same results.
I then put the crs powersupply back into #1 son's old case reinstalled the nx6600 and gave it a go
Particulars for the old computer ECS K7VTA3 ver. 1 Mobo with 512 Mb DDR, nx6600VTD256 vid card and the CRS Power supply 300 watts with 15 amps on the 12 volt rail , and win XP pro service pack 2.
Funny the card works great without any problems with this setup! And the powersupply is 50 watts less and only 15 amps as compared to the other with 18!
I then pulled all the hardware out of #2's computer and tried it with only the memory, cpu, and NX6600 connected.
I had to boot 5 times before I had a working screen.
Now I'm thinking that there is somthing amiss with the NX6600 and the MSI 845 Pro2 ???
I'm thinking that I would be better off installing the K7VTA3 in #2 son's computer with the NX6600, since this works fine. When I did a benchmark with this setup it outperformed the *45 Pro 2 NX6600 combination By 300 points 2600 as compared to 2300 aqua mark points.
Isn't this fun?

Black screen after stuck in lenovo logo

Similar Messages

Maybe you are looking for