Black screen and bulge-crack in bottom of case

My white MacBook will turn on and appear to run (by watching the power/sleep light on the front), but there is no activity onscreen. It stays black. There is no image at all, so it is not a matter of the backlight being off.
The only odd thing is that it has a small bulging, cracked area on the bottom of the CASE, between the right-hand side hinge and the near edge, and slightly toward the front of the machine. It looks as if something is trying to push its way out of the case. The bulge is only a mm or so, but its enough to have cracked the case in a star pattern.
The machine has never been dropped or mistreated in any way. Kid gloves handling.
Anyone else see anything like this?
Thanks

sounds like somethng has failed and in the process expanded/distorted enough to affect the case, probably got hot too
to avoid further damage, don't power it up, also remove the battery
is it still within warranty? if not look online for a repair service - apple's out of warranty service is usually expensive, you should be able to get a better price elsewhere
but if the damage is significant then it might be uneconomic to repair

Similar Messages

Blank Black Screen And Blue Screen. Do I Need To Do Reflow To Ati Chipset?

Hello i want to tell you my problems and what i did until now.
I have hp pavilion dv3 4150st. I was using win7 64 bit . and i was geting an error that says "display driver amd driver stopped responding and has successfully recovered".I started to get this eror often . And a few days later my pc startet to get blue screen errcor after a few second later than display driver error. . And after 2-3 blue screen error i lost my screen. It was blank black . when i restart pc the screen was blank black. there was no image. When i started to fix another monitor, i saw screen . And i installed the win 7 with another external monitor. Bu i had still black screen after install the windows.. Itand was still black after i remove the ectgernal monitor. I installed bios again but i had still black screen. And i tried the install ati display driver after installing windows . But after i installed the display driver, i had the blue screen error again. And now i have still both blank black screen and blue screen problem.
I cleaned the motherboard. I resetted bios. I installed bios. i installed windows again. i installed ati display driver.But these couldnt solve the problems. Please can you tell me what can i do now ?

Hi beginner_2012,
Thank you for your post, I will do my best to assist you.
I grasp that you were getting the error "display driver amd driver stopped responding and has successfully recovered" quite often. Then a few days later you got the blue screen then the above error message, after 2 -3 more errors the screen is now blank or black. Here is a document to assist you with this. Troubleshooting Black Screen Displays with No Error Messages During Startup or Boot.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

I use Safari as my browser. When on a site and I click on a PDF file I get a black screen and a notice that "Adobe Reader blocked for this website". However, this does not happen if I use Firefox.

I use Safari as my browser. When on a site and I click on a PDF file I get a black screen and a notice that "Adobe Reader blocked for this website". However, this does not happen if I use Firefox.

Back up all data before making any changes. Please take each of the following steps until the problem is resolved.
Step 1
If Adobe Reader or Acrobat is installed, and the problem is just that you can't print PDF's displayed in Safari, you may be able to print by moving the cursor to the the bottom edge of the page, somewhere near the middle. A black toolbar may appear under the cursor. Click the printer icon.
Step 2
There should be a setting in its preferences of the Adobe application such as Display PDF in Browser. I don't use those applications myself, so I can't be more precise. Deselect that setting, if it's selected.
Step 3
If you get a message such as ""Adobe Reader blocked for this website," then from the Safari menu bar, select
Safari ▹ Preferences... ▹ Security
and check the box marked
Allow Plug-ins
Then click
Manage Website Settings...
and make any required changes to the security settings for the Adobe PDF plugin.
Step 4
Triple-click anywhere in the line of text below on this page to select it, the copy the selected text to the Clipboard by pressing the key combination command-C:
/Library/Internet Plug-ins
In the Finder, select
Go ▹ Go to Folder
from the menu bar, or press the key combination shift-command-G. Paste into the text box that opens (command-V), then press return.
From the folder that opens, move to the Trash any items that have "Adobe" or “PDF” in the name. You may be prompted for your login password. Then quit and relaunch Safari.
Step 5
The "Silverlight" web plugin distributed by Microsoft can interfere with PDF display in Safari, so you may need to remove it, if it's present. The same goes for a plugin called "iGetter," and perhaps others — I don't have a complete list. Don't remove Silverlight if you use the "Netflix" video-streaming service.
Step 6
Do as in Step 3 with this line:
~/Library/Internet Plug-ins
If you don’t like the results of this procedure, restore the items from the backup you made before you started. Relaunch Safari.

HP G62 US-340, Black screen and flashing caps lock

HP G62 US-340, Black screen and flashing caps lock when i power it on, And some time it comes on like it should. I tried draining all power from unit to reset and that wasn't any help. Can you help me Please ?
This question was solved.
View Solution.

Hi @mikeyh25
Thank you for your query, I will do my best to help!
I understand that when you start up your notebook you get a black display with no error messages,but you see the Caps Lock light flashing.
Here is a link to assist you. Computer does not start and the LEDs blink or the computer beeps.
Best of Luck!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

A movie I bought a while ago will no longer play, instead it just shows a black screen and no audio. All of the other movies in my library play fine. Any ideas as to whats going on or how to fix it? Thanks for any help.

A movie I bought a while ago will no longer play, instead it just shows a black screen and no audio. All of the other movies in my library play fine. Any ideas as to whats going on or how to fix it? Thanks for any help.

Hi 22chill,
I recommend that we delete and re-download the movie from your purchase history:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
http://support.apple.com/kb/HT2519
Thanks,
Matt M.

Recently loaded Lion on my laptop and now my computer crashes often. Black screen and keyboard lights up. Any ideas on what's wrong and how to fix this?

Recently loaded Lion on my laptop and now my computer crashes often. Black screen and keyboard lights up. Any ideas on what's wrong and how to fix this?

Everytime this happens Ihave to power down and restart! Any ideas would be appreciated!

Screen problems - black screen and lock-up (plus HDMI issues)

Hi, I'm not sure if these are related to the same fundamental issue, but they are both serious problems that need resolution.
I have a new mid-2012 MBPretina. I am on all the latest updates (10.8.2).
The first problem is the most recent, and the most serious problem. Since I updated the Java a couple of days ago I've been experiencing random black screens and lock-ups. Essentially, what happens is that sometimes when I perform an action (opening an app, clicking a link on a webpage, performing other kinds of in-app actions, etc.) the computer screen will go black. About half the time I can, through my own memory, try keyboard combinations to quit or force quit the most recently used app (the one where the action was just performed), and I will get some glimpse of the underlying apps, while the menubar and other areas will remain black until I move a window on top of the black space. Sometimes no key combinations work and I am forced to perform a hard restart with the power button. This is a serious issue, obviously, since I will lose current work/progress in my apps. I'm not sure if this is because of the new Java update, or has to do with something else, but it started happening shortly thereafter, over the last 2 days. I work most of my waking day on my laptop, and this "black screen of death" has happened about 5 or 6 times a day.
The second problem I have been experiencing since I starting using my MBPr with external HDMI displays in August/September. The problem is that I will plug the MBPr into an HDMI display, the screen will temporaliy go black, and then bring me to the login screen (as if it's crashing, albeit softly). This happens about 1 out of 4 times nowadays.
How can I fix these problems, especially the first?

UPDATE:
Clearly there's a problem because a third of the way through a clean reinstallation from scratch it black screened again. Hmmmm.
Now this is not good. Problem is I can't rule out potential updates from Apple that might have caused this either.
The search for solutions continues.

My ipod 5th gen ios 7.0.6 crashed and keeps going from the apple logo, going to a black screen, back to the apple logo, then back to the black screen and so on. Furthermore, my laptop doesn't recognise that the iPod is connected. What do I do?

My ipod 5th gen ios 7.0.6 crashed and keeps going from the apple logo, going to a black screen, back to the apple logo, then back to the black screen and so on. Furthermore, my laptop doesn't recognise that the iPod is connected. What do I do?
Please help me out as this is very irritating. This has been happening for the last 20-30 minutes. It had roughly half battery left.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

How do you fix an ipod that has a black screen and it turns on but when it turns on the screen gets a lighter black but you still can't see the apps or anything?

How do you fix an ipod that has a black screen and it turns on but when it turns on the screen gets a lighter black but you still can't see the apps or anything?

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar
Apple will exchange your iPod for a refurbished one for this price. They do not fix yours.
Apple - iPod Repair price
A third-party place like the following maybe less. Google for more.
iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
Replace the screen yourself if you are up to it
iPod Touch Repair – iFixit

Ipod touch 2G is black screen and won't restore in Itunes (error 21)

I have aquired an Ipod touch 2g 16g that I was hoping to make a present to my daughter with. The device is I guess what is called "Black Screen of Death". I can't get any image to display on the Ipod when trying to charge (which it apparenlty accepts) the item or when trying to connect it to Itunes. Itunes recongizes the item in recovery mode, and attempts to restore the item and consistantly gives the error 21 message. I am using Windows 7 and have tried to restore the device on a laptop running Win XP with the exact same results. The screen will turn white during the process, and the machine will from what I have read and believe go into DFU mode, but it stops with error 21. I am a Noob and have googled and googled for a week now with no luck. I have tried the reinstallation of Itunes, all the updates to both Itunes and the machine, no security software, the works. I tried connecting it to older son's laptop running Win 7 which he uses for his Ipod 2g 32 gig without problems. My device was recognized on his machine, and he said on his Itunes he briefly saw songs on the device he did not have on his machine/device in his library before it hung again in the recovery mode loop. I have read different articles and tutorials on jailbreaking and tried loading just the 'oem" firmware from apple with Redsnow and thought i was successful. The device went through the process of white screen, several boots/dings of on my PC, and then an image appeared on the Ipod of "loading Jailbreak data". After a few moments/minutes it then began what I believe is displaying the "verbose" booting running the lines of text on the screen. I then notice it to stop and give me an error of something to the affect of init failed, and then a "lan error, watchdog timeout, giving up, a long pause, then quick scrolls down the screen and reboot back to white screen. Holding the power button or home/power button puts it right back to a black screen and in the Itunes recovery mode loop/error 21 again. Can anyone please help me resolve this issue before I pull what's left of my hair out. I would love to get this working for my daughter before her birthday. Thanks in advance to anyone who helps.

Common, no one has any ideas? Well, don't know if this will help, but here's some new data to process. I noticed that when I was trying to load the firmware with Redsnow w/o installing any options to include Cydia I got errors displayed on the Ipod such as WMR NAND format invalid; NANDLegacyFTL failed. Someone has got to know something. I would appreciate any ideas or thoughts from anyone with any idea. Thanks

My ipod touch has a totally black screen and is unresponsive, how do I fix it?

Long story short, my 3rd generation touch is completely unresponsive: black screen and everything. I've tried resetting, no go. Still black. I've tried charging, no go, still black. I can't even reset it because windows doesn't detect it when it's plugged in.
I worked fine an hour previous to its unresponsiveness.
How can I fix this?

If not successful try the remaining items of:
iOS: Not responding or does not turn on
If not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

Ipod nano black screen and isn't recognized on itunes

Ipod nano 7th gen was working fine then the music started lagging and after about 30 seconds it just stopped working. I now have a black screen and it wont turn on. It is not being recognizedin itunes. What do I need to do to fix this issue. Any and all help would be very helpful. Thanks

Have you tried doing a Reset (restart) in the iPod?
http://support.apple.com/kb/ht1320
In case the battery is low on power, you can try this while the iPod is connected to power.

All my downloaded(digital copy) movies will no longer play in itunes, i get a black screen, and no sound, but the time keeps going. how can i fix this?

All my downloaded (digital copies from dvds) won't play in itunes. I get a black screen and no sound, but the time keeps moving. How do i fix this?

Hi 22chill,
I recommend that we delete and re-download the movie from your purchase history:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
http://support.apple.com/kb/HT2519
Thanks,
Matt M.

After errors with disk partition, I removed Windows from my iMac. Now when I start my computer it goes into a black screen and not straight into the Mac area like it used to, unless I hold Alt straight away to give me the option. Any help?

Hi,
Sorry, I'm new to the community, so apologies if I'm repeating myself.
OK, so I tried to install Windows Vista onto my iMac with the disk partition. Everything was going fine and it wasn't until last minute, when it was installed that an error came up saying that this can only be done with Windows 7. After this error, I couldn't access any errors of my iMac and when I shut down and restarted my computer, it automatically logged into Windows.
So after a panic, I rang Apple Care and the lady helped me log into my apple area, delete Windows from my iMac, and all was restored.
However, now when I shut down my computer and boot it back up, I think my iMac is trying to log into Windows areas that no longer exist. It loads up a black screen and doesn't move from there. To log into my Apple area, I have to do the whole process of holding Alt immediately after I switch the power on and access the Mac drive and log in that way.
It's beginning to become a real pain and I'm paranoid this process is going to damage my computer. Any advice on how to restore logging-in back to it's former glory when I first purchased it?
Thanks

Solved it. Thank you very much for that!

My ipod has a black screen and will not turn on how can i fix it

I have tried everything that i can to get my ipod to turn on. It has a black screen and hasnt done anything atleast 2 weeks. Please help.

1. Can you get it to light up doing a hard reset and holding the buttons down for at least a minute?
2. Is it charged up?
3. Is the USB power cable good?
4. Can you get iTunes to recognize using recovery or DFU mode?
Basic troubleshooting steps
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
 In Memory of Steve Jobs 

Black screen and bulge-crack in bottom of case

Similar Messages

Maybe you are looking for