Black screen during starting up windows XP

Hi everybody I am using MBP.
Whenever I use BootCamp to start my Windows XP, after appearing the Windows XP logo and the loading bar, the monitor goes to near complete darkness, not 100% dark. After a minute or two, the login screen appears. I want to know why the screen was blackened was such a long time. I have the Parallel installed. This problem does not appear when I was using it in early stage.

It was the PRAM.

Similar Messages

  • Apples update didn't work for me: Boot Camp: iMac displays a black screen during installation of Windows 7

    Boot Camp: iMac displays a black screen during installation of Windows 7 - Apple Support
    I have followed each of the steps listed in the link above with no success.
    Prior to adding the extra drivers I was able to start the Windows install process up to reformatting the "Windows" Bootcamp drive. After that the computer would go through some instal processes and eventually restart. After the restart the screen would go black. The black screen lead me to the  Apple Support link above dated March 5 2015. After going through steps listed in the link above, I get an error message stating that the D:\Sources\instal.win. file cannot be located. I am forced to restart the computer at that point and theWindows install process attempts to start again but always ends up at the same point.
    Note: I am installing windows 7 Pro from a DVD. I scanned the AutoUnattend.xml file and noticed that it refers to "Windows 7 ULTIMATE" but not "Pro" or any others that I could see. (see below). Could that be part of the issue?
    Any feedback would be greatly appreciated.
    <cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
    </unattend>
    iMac (27-inch, Late 2009)
    2.66 GHz Intel Core i5
    16 GB 1067 MHz DDR3
    ATI Radeon HD 4850 512 MB

    Here is an over-simplified explanation of WIM and CLG files. Assume your DVD Media contains
    W7- Ultimate
    W7- Professional
    W7- Home Premium
    W7- Home Basic
    WIM Files
    File1
    y
    y
    y
    y
    File2
    y
    y
    y
    y
    File3
    y
    File4
    y
    y
    File4
    y
    y
    y
    The File .wim will contains a compressed image which contains File [1...5].
    The W7-Ultimate .clg will have 5 entries, with all set to 'Y'.
    The W7-Professional .clg will have 5 entries, with 'Y','Y','N','Y','Y'.
    The W7-Home Premium  .clg will have 5 entries, with 'Y','Y','N','N','Y'.
    The W7-Home Basic .clg file will have 5 entries, with 'Y','Y','N','N','N'.
    This allows a single .wim Image file on the DVD media to be used to install any of the 5 flavors of Windows. When you enter your product key, the Installer knows what specific W7 variant you have the key for and will tell the WIM to extract the specific files the installer needs to be extracted.
    The following line
    <cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
    is telling that a retail product key will be entered, which should go look for this specific .clg file (from the five you already have on disk).  You can test if it will work for you by changing this line to the following
    <cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 PROFESSIONAL" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
    If it does not work, the other issue can be related to device discovery. Typically A: and B: device names are reserved for Floppy Drives. C: is your internal HDD.
    D: can either point to the Optical drive, or the USB. The normal convention is that the removable media is named from Z: backwards. Y: and Z: are usually used for Network drives, so X: should be your USB. First try with the change to "Professional". If it does not work,

  • IMac displays a black screen during installation of Windows 7

    I tried to install windows 7 on my imac 27" but imac displays a black screen during installation of windows 7.
    I also tried to install it as apples instruction of http://support.apple.com/kb/ts3173 but it failed.
    Any solution please.. thanks
    I have a late 27" imac with OS X 10.85

    Here is an over-simplified explanation of WIM and CLG files. Assume your DVD Media contains
    W7- Ultimate
    W7- Professional
    W7- Home Premium
    W7- Home Basic
    WIM Files
    File1
    y
    y
    y
    y
    File2
    y
    y
    y
    y
    File3
    y
    File4
    y
    y
    File4
    y
    y
    y
    The File .wim will contains a compressed image which contains File [1...5].
    The W7-Ultimate .clg will have 5 entries, with all set to 'Y'.
    The W7-Professional .clg will have 5 entries, with 'Y','Y','N','Y','Y'.
    The W7-Home Premium  .clg will have 5 entries, with 'Y','Y','N','N','Y'.
    The W7-Home Basic .clg file will have 5 entries, with 'Y','Y','N','N','N'.
    This allows a single .wim Image file on the DVD media to be used to install any of the 5 flavors of Windows. When you enter your product key, the Installer knows what specific W7 variant you have the key for and will tell the WIM to extract the specific files the installer needs to be extracted.
    The following line
    <cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 ULTIMATE" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
    is telling that a retail product key will be entered, which should go look for this specific .clg file (from the five you already have on disk).  You can test if it will work for you by changing this line to the following
    <cpi:offlineImage cpi:source="wim:d:/sources/install.wim#Windows 7 PROFESSIONAL" xmlns:cpi="urn:schemas-microsoft-com:cpi" />
    If it does not work, the other issue can be related to device discovery. Typically A: and B: device names are reserved for Floppy Drives. C: is your internal HDD.
    D: can either point to the Optical drive, or the USB. The normal convention is that the removable media is named from Z: backwards. Y: and Z: are usually used for Network drives, so X: should be your USB. First try with the change to "Professional". If it does not work,

  • HT3986 i get a black screen during windows 7 installation on bootcamp 5.0.1

    i get a black screen during windows 7 installation on bootcamp 5.0.1 , it wont install

    Hi wb2009,
    I haven't found that the TV would be an issue, but did find an article that states to not have extra USB devices connected.
    Boot Camp: Windows installation boots to black screen with blinking cursor
    http://support.apple.com/kb/TS4536
    The Windows installation may boot to a black screen with a blinking cursor. This can occur if you use a USB optical drive or USB Flash drive for the Windows installation and another USB device is also connected to the computer.
    There's another article that mentions Windows XP or Vista that may apply.
    Archived - Boot Camp: Start up to black screen after installing Windows
    http://support.apple.com/kb/TS2600
    Thank you for visiting Apple Support Communities.
    Nubz

  • Black screen during windows 7 install on 27inch iMac

    My iMac turns to a black screen during windows 7 boot camp install. I can use the install disk on my wifes Macbook Pro so I know that the media is good.

    Please re-post in the Boot Camp forum.

  • Probelm while installing windows 7 on MacBook pro through bootcamp? I am getting a black screen during installation

    Probelm while installing windows 7 on MacBook pro through bootcamp? I am getting a black screen during installation

    Apple Support Boot Camp
    Is there any article in the above?
    did you read the pdf before beginning from Boot Camp Assistant?
    Did you upgrade to Lion or was it pre-installed?

  • Cannot reinstall windows 10 Technical preview after getting black screen at start. will not let format drive or install

    cannot reinstall windows 10 Technical preview after getting black screen at start. will not let format drive or install

    you may need to use a DVD from an earlier version of Windows or slave the disk to wipe it with disk manager
    Place your rig specifics into your signature like I have, makes it 100x easier!
    Hardcore Games Legendary is the Only Way to Play!
    Vegan Advocate How can you be an environmentalist and still eat meat?

  • Black Screen During Gameplay and not High Demand Renders?

    Hi, 
    The computer I own has been having issues with games that it previously had no problem with. 20-30 minutes within a session the screen will go black and audio will continue momentarily. The only way out of this issue is to hold down the power button for a reset. I have updated my drivers and cleaned out any dust with pressurized air. But the problem still continues. The strange thing is that I use Photoshop and After Effects for my work and there is no issue. Need help!
    Computer Specs:
    Model: HP Omni 220-1150xt
    OS: Windows 7 Home Premium 64-bit (6.1, Build 7601).
    BIOS: Ver: LAV_7 8.ROM vLAV7.08
    Processor: Intel(R) Core(TM) i7-2600S CPU @ 2.80GHz (8 CPUs), ~2.8GHz
    Memory: 8192MB RAM
    Available OS Memory: 8172MB RAM
    DirectX Version: DirectX 11
    Graphics Card name: AMD Radeon HD 6550A
    Card Manufacturer: Advanced Micro Devices, Inc.

    Hello masinic2,
    I understand that just recently you started getting freezing and a black screen during game play and are looking to resolve it. I am providing you with an HP Support document: Using Microsoft System Restore (Windows 7), which will walk you through restoring your computer back to a point in time where you did not have this issue. This will not affect your personal files, but it will affect any applications you have installed or settings you have changed between now and the time you restore back to. You will have to reinstall or redo the changes that are undone during that time frame.
    Please re-post if you require additional support. Thank you for posting on the HP Forums. Have a great day!
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    Dunidar
    I work on behalf of HP
    Find out a bit more about me by checking out my profile!
    "Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

  • BLACK SCREEN on start up with 3 beeps, FREEZES when power unplugged, IF IT BOOTS splash screen freezes, OVERHEATING REQUIRED TO BOOT - 0x7B, Event 41 kernel-power

    Issue: One day I unplug the power, the screen freezes and I get frozen music sound. I shut down, start up, I get 3 beeps (1 short 2 long), which indicates a Video failure according to the Thinkpad Laptop beep code list.
    How I solve the issue day-to-day: I turn the heat up - I disconnect the battery and hard drive and plug in the power then turn it on. I will wait until the underneath is searing hot with a blanket blocking the fan's flow of air, I mean way hot because any
    cooler and it won't start. Plug stuff back in, Hard drive first, Battery second, turn off with power button hold, unplug power, replug power. 
    I turn it on, no beeps, it goes past the first Lenovo screen, then gives me a prompt because it "didn't shut down properly" and continue regular startup. What happens next is the Windows logo appears,
    and just as the animated windows logo starts to move (you see 2 small colored dots on the screen), it freezes. I see this every time, I know naturally that it means that the laptop is still too hot to go past that point, so I shut it down and try again. After
    about 5 - 10 tries it will go past the splash screen and into the login area, then it's all fine. 
    Sometimes when I unplug the power from the back by accident it will freeze. By accident I mean that the connector wiggles it's self out easily. This unplug freezing thing started happening about 1 week before the 3 beep black screen problem started rolling,
    so I'm putting 2 together.
           Errors:
    I got a Blue Screen of Death the first time I started it up with the overheating ritual, but I never got it since. It was 0X7B.
    I got another Blue Screen of Death about a week ago, but came as it was on already and I had been using it, and said something about disabling Cache or Shadowing in BIOS. I never got it since.
           Event Viewer events found:
    1. Kernel-Power, Summary page.
    There are critical events for a few things like Kernel-Power, Event ID 41, Task Category (63). There are 19 of them, each day 1 or 2 of them but mostly 1, so this maybe corresponds to my daily ritual.
    "The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly."
    2. Kernel-Processor-Power - Event ID 37, task category (7)
    "The speed of processor 1 in group 0 is being limited by system firmware. The processor has been in this reduced performance state for 71 seconds since the last report."
    3. LMS - HCMI - Event ID 2, Task Category: none
    "LMS Service cannot connect to HECI driver".
    I came across a very sluggish performing control panel for Nvidia before and after this problem, and I tried installing a newer version, which I had to jump through a few hoops to do, like uninstalling first, not just updating. At first it said that the
    driver wasnt for the system, which was wrong. I made it work somehow, but it was still sluggish. I rolled it back to an earlier driver, and now it works fine. No sluggish performance / slight freeze window thing going on.
                 MSCONFIG.exe, Boot Advanced Options: I have tried twice to change this 1 setting, check box "Number of processors" and change to 2 processors, because I do have 2 processors. I have been able to change
    this in the past, but it does not save the setting now, and I believe this option was selected before I started having problems, and settings did not disappear then.
    What could this be. The small round BIOS battery? The video card like everyone presumes? (I.E. the entire motherboard replacement), Software? The wiggly power input area? (Not enough power getting in?), Firmware of some sort? The BIOS software being wrong?
    SYSTEM INFO:
    Thinkpad T61p 6457-A24, Intel core 2 duo (T7700) 2.4GHz, Intel 120GB SSD 6Gb/s, NVIDIA Quadro FX 570M (256 MB),
    Windows 7 64 bit Home Premium (6.1, Build 7601), BIOS Ver 1.00PARTTBLx
    Display: 1680 x 1050 (32 bit 60 Hz), Integrated RAMDAC, Main driver: nvd3dumx.dll,nvwgf2umx,nvwgf2,
    Version 8.17.12.9688, Date 5/31/2012, DDI version 10, Driver model WDDM 1.1
    Please excuse the small text at the beginning, there isn't an option to un-do that error.

    You are very wrong about that mystified. What do YOU think made my computer work without beeping at all hu? (I bet you're gonna tell me). I figured it out.
    RE-INSTALL WINDOWS 7 OS.
    SOLVED.
    DOESN'T BEEP ANY MORE.
    THAT IS A PART OF microsoft ISN'T IT.
    ::: EGO KILLER 9000 :::

  • MacBook stuck at gray screen during start up

    Lately my 2008 model MacBook has been freezing up. When I shut it down, it starts up just fine, however, the last two times I've shut it down, it gets stuck at the gray screen during start up. The first time, I was unsuccessful with a Safe Boot, however I was successful using CommandOption+PR to reset my NVRAM/PRAM. It has been working fine for the past two days, but it froze again this evening. I tried Safe Booting, removing peripherals, resetting the NVRAM/PRAM and I even was able to repair the disk and the permissions, but still, I am unsuccessful during a start up.
    When I did try to "Perform an Archive and Install installation of Mac OS X", it said my computer was not able to install 10.5 (I run 10.6) because it did not meet the system requirements.
    As a final effort, I tried doing another SafeBoot, this time viewing the status. It has been stuck at a console screen that reads "disk0s2: media is not present...." for about ten minutes now, if that helps at all.
    Any advice on how to fix this would be highly appreciated. And yes, I have read the Gray screen article
    Zach Irwin

    Your hard drive may be damaged or requires reformatting. You might try this to start:
    Repairing the Hard Drive and Permissions
    Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    If you still are unable to restart or if DU cannot repair the drive or the SMART status is not "verified" then you can try reformatting the drive to see if that fixes the problem, otherwise you will have to replace the drive.
    Extended Hard Drive Preparation
    1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.)
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
    And, you cannot do an Archive and Install of Leopard over a Snow Leopard installation. You have to reinstall using the Snow Leopard installer.

  • I'm getting the grey screen during start up and can't boot the computer. I did a cmnd R but worried it would automatically wipe my hard drive and reinstall OS.  Is there a risk at cmnd R will result in wiped HD without me actively making that choice?

    I'm getting the grey screen during start up and can't boot the computer - MacBook Pro with lion.
    I did a command r after doing some research but got nervous that it would automatically wipe my hard drive and reinstall OS.
    I was nervous because it asked me for language for software use before any options were presented (such as repair via disk utility). It looked similar to an OS install.So I powered off....Is there a risk at command r will result in wiped HD without me actively making that choice?

    Repair the Hard Drive and Permissions - Mavericks, Lion/Mountain Lion
    Boot to the Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
    Reinstall Mountain Lion or Mavericks
    OS X Mavericks- Reinstall OS X
    OS X Mountain Lion- Reinstall OS X
         Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is
                    three times faster than wireless.

  • What would cause a prolonged blue screen during start up?

    I have an iMac desktop.  Recently I've had trouble with a prolonged blue screen during start up (approx. 10 mins) before it finally takes me to the login screen.  Any ideas why this is happening?
    Jeff P.

    Hi Jeff,
    Open console in Applications>Utilities, check the system log for the date/time of the last problem Startup for clues.

  • I solve my problem of black screen when starting up my Mac pro, namely by the button lighting and then i saw the login screen. Hopefully it works for you too.

    I solve my problem of black screen when starting up my Mac pro, namely by using the lighting button and then i saw the login screen. Hopefully it works for you.

    It was the PRAM.

  • Macbook pro-Freezes with black screen at start up.

    Macbook pro-Freezes with black screen at start up. I've tried inserting the Mac OS X install disc to run the hardware test(Restart and hold down D), But it still does nothing. Just the black screen. Now I can't get the disc out. I've tried holding down the track pad key upon start up but that doesn't work neither.
    What do I do??? Please help.

    Remove the battery to find your serial number in the battery bay. Then you can look your MBP up on EveryMac.com:
    http://www.everymac.com/ultimate-mac-lookup/
    That will give you all the information on your Mac.
    This is assuming that you have the MBP with the removable battery and not the unibody. The unibody has different graphic chips.
    Good luck!
    Message was edited by: S.U.

  • MacBook Pro 2006 black screen on start up

    MacBook Pro 2006 black screen on start up

    Time to take a trip to the Apple store genius bar for a free diagnosis.  It could be a faulty GPU, faulty display or a bad display connection.
    Ciao.

Maybe you are looking for