Black Screen Problem after/durning installing MSI Driver CD (ATI 4780 1 GB)

Hi,
I've recently purchased a your (MSI) Radeon 4870 1GB video card from Newegg. And I've installed it and I have the latest drivers (from windows) for it. But ever time I try and install the MSI CD on my computer the screen goes black (could possibly freeze but I don't know cause the screen is black) when installing it or upon the restart my computer. Do you have a solution for this problem? I've tried pretty much everything I can think of so far. I have SP2 Vista, I've tried to install it with and without anti-virus on also. I know this is the problem because when I go into safe mode and uninstall it my computer works fine again. I also built this computer a couple of weeks ago too FYI. On another note when the MSI CD is not installed the graphic are spectacular and very game that I've tried works at full setting.
Spec:
MSI R4870-MD1G Radeon HD 4870 1GB
ASRock M3A780GXH/128M AM3 AMD 780G HDMI ATX AMD Motherboard
AMD Phenom II X4 810 2.6GHz
Crucial 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1333
Sunbeam PSU-BKS580-US 580W ATX Power Supply (output: +3.3V@30A,+5V@36A,+12V@25A,[email protected],[email protected])
Western Digital Caviar Blue WD5000AAKS 500GB 7200 RPM
Thanks, Adam

Quote
And I've installed it and I have the latest drivers (from windows) for it
Quote
On another note when the MSI CD is not installed the graphic are spectacular and very game that I've tried works at full setting.
Well if its working very well for you, then don't install from the CD.

Similar Messages

Black Screen Problem after installing MineCraft MCedit

After installing MCedit, the problem starts with frequently whole black screen. At first from time to time, few seconds. Then within around two days it went worse, that means more often and longer black screen. By now (three days later) while booting I just get the screen for some seconds or half a minute... then just black screen... Mac is running. Apple support say it's most likely a hardware problem. I'm not sure about... any idea what to try about? I tried all the boot options I found :-) doesn't help (iMac 27'' / Lion)
Thanks

Quote
And I've installed it and I have the latest drivers (from windows) for it
Quote
On another note when the MSI CD is not installed the graphic are spectacular and very game that I've tried works at full setting.
Well if its working very well for you, then don't install from the CD.

Screen Problems after Leopard install.

When I first installed Leopard, I got a black screen full scrolling white text after only 10min of use.
I did a clean install and that problem is gone, but I'm still getting very odd screen problems. The Apple logo and translucent part of the menu bar go away at times and it freezes some times too.
I was wondering if any other iMac G4 users have had these problems... ???

I believe the default settings for labels and text in Finder windows, if that's what you mean, is 12 point. You you can change font size through View Options. Text sizes for menus, etc. is fixed; I don't know what the size is specifically. For Firefox, text size for web pages is specified by the web site generally, but you can change the size Firefox will default to in the Firefox Content preferences.
I hope I've answered the question you were asking. Regards.

How to How to install ATI Radeon HD2600 driver on bootcamp 3.0 windows 7 partition w/black screen problem

Ok....so i've posted this question in a different way, and i gotten several "scratch the surface" answers from people just saying to install "Ati catalyst", or insert the os x dvd and run set up.exe, and update to boot camp 3.1 or 3.2...while these all seem like great suggestions, I am finding myself needing more specific direction or "hand holding" so to speak.....here is the MAIN problem...
The Background/history
I used boot camp (3.0, and i found updates for 3.1 for imac and for windows, but can't find for mac pro, AND they all are ".exe" files which run on windows..which as you'll see is the big part of my problem...So I recently updated my mac pro (with the ATI Radeon HD2600 graphic PCIe card with 10.6.7 from 10.5.8. I created a single partitioned drive to install windows 7 professional 64 bit. The download software function didn't work (Thanks, APPLE for that poor level of support) so have to select the option that i have already downloaded, or have other media with the drivers already on it....i restarted with the windows 7 disk in....
The installation of Windows 7 Pro 64-bit
So the installation of windows 7 seemed to go flawlessly, was able to use my existing 23" hd apple cinema display (so somehow it has drivers that work with the graphics card, or maybe the motherboard's on board video components) and i select english, and install now, custom, blah, blah, blah...installation causes a few reboots, then restarts ultimately back in os x since that is the default boot os i use on this desk top and have to do the "opt" button to select booting in windows....so when i try restarting in windows, now using the actual boot drive on which i am installing it, it ran through another reboot or two, but then after that, my display goes black.... in the communities, the solution sounds super simple... "go download the ATI catalyst for the black screen problem....windows 7 doesn't have device drivers that work with the ATI radeon hd2600...no problem, just go download and install...."
The problem, re-emphasized : I cannot even finish the install for windows, because of this driver problem....i cannot see anything....I have tried to reboot in safe mode, and that then seems to invoke whatever basic drivers that do work, likely through the motherboards onboard video vs the actual graphic card, and the screen works and says that it's wanting to complete the installation, so i'm thinking awesome this is gonna work....and then.. "windows installation was not completed and cannot be completed in SAFE MODE, need to restart, blah, blah, blah" pops up...and forces reboot...so Safe Mode allows me to see, but won't allow me to finish the install of windows 7...and without completing the install i can't run (ranther I DONT KNOW HOW TO) any of the various .exe files everyone is telling me are the solutions to my problem...like update 3.1 and 3.2 bootcamp...they're all .exe files? not sure why, because bootcamp runs in 10.6.7 i thought, but whatever...it needs running Windows to execute...then the ATI radeon hd2600 driver for windows 7 that i downloaded from the site has an installation program that is an .exe file, which needs windows to run... Does this make sense, why i can't just use these fixes, that seem to be the only fixes out there....so can someone school me step by step here (not just the highlights) of how to update bootcamp, and how to install the ati radeon driver without having been able to complete the windows 7 installation because the monitor goes and stays black????
This is so very frustrating for the record...and any substantial help "not just go download this..." would be immensely appreciated.
Some other things i've been told to try that i've tried and nothing seems to happen as i'm told it will....
---I've been told to install the osx dvd and run "setup.exe" - AGAIN...it's an exe file...and 2 - when i put in the os x file it just wants to re install 10.6...so need more help if this is even a real solution to understand how to make it work...
---I've been told to update boot camp to 3.1 and/or 3.2 from 3.0, using Apple Software Update....Well, my software update is saying everything is up to date and there is nothing new to download at all, and when i reverify the bootcamp version it is still only 3.0.2...and again downloading the updates from www.apple.com/support/ for 3.1 and 3.2...all of those are .exe files...need windows to run them...again, refer to the problem described in detail above...
---I've been referred to the black screen on imac early 2011 thread saying it should fix my problem...and reading it it SEEMED like the most promising resolution...it involves creating a boot flash drive for windows 7 and an xml file that sets the imac drivers to auto install during the windows installation..and it got me farther than anything else..but still ultimately ended up in the darned black screen...my assumption is that it's because it's for imac and not mac pro so not ati-radeon specific drivers....ok....that's enough..please...anyone who thinks they can help...your help is desperately needed...thanks so much in advance!

hey Hatter, thanks so much for getting back...so just to be super clear...is there no way to install the drivers using an exe file given my current state? no way to do it with command prompt or something? if can make work with existing card, i'd prefer it...now when you say it's 'toast' how do you mean? it works well with the os x partitions and always has...so i'm not sure i follow, just want to be clear...
Now to your point of starting with only the one drive installed...so i would put that bootcamp drive in bay 1 and disconnect the rest...i'm not totally sure what you're suggesting the effect should be of doing this? just that i'm just installing windows without the bootcamp deal...but if windows 7 doesn't support the ati radeon hd2600, it still will go black screen no? or you're saying it will run video through the motherboard if it's the only bootdrive, and will run all the way through the windows install without trying to switch over to the hd2600? (slrry flr these questions..just really want to make sure i understand what you're telling me..thanks so much for your patience and help by the way...it's very greatly appreciated...your support is priceless!
So now, assuming none of the above is possible...referring now to the ati 5770 that you referred to...you mention it works with 10.6 well, and that windows 7 supports it ...2 questions on that
1) Windows 7 supports" meaning, out of the box windows 7 supports it? or will i have to install drivers still through some update, because again, if that's how i have to do it, then won't work, cuz can't start windows to see anything to install any drivers or run any thing at all...so it would have to just work with initial installation.
2)hardware wise for my Mac Pro 3,1...intel dual quad core xeon, blah blah....will this card work? it's a PCIe and should fit on my board no prob, etc?

MSI 290X LE Lightning Edition black screen problem

I recently bought the above graphics card, only to run into problems with black screen, furmark blackscreens when it reaches just over 70c & games that push the card ie Crysis 3 also causes black screen problems, I'm also sometimes getting desktop corruptions, usually after it black screened.
My PSU is a 850watt EVGA SuperNova G2 so i know it's not that what causing the problem.
rest of my setup as follows
3770K @4.2Ghz
MSI Z77 Mpower
8GB corsair memory
ect ect.
Any idea's as to the cause of the problem?
edit here what it doing I've uploaded it to youtube.

First of all remove any oc. Then list specs more detailed: >>Posting Guide<<

Black Screen Problem on my Toshiba Portege M800-A330

I own a Toshiba Portege M800-A330 for more than a year now. Whenever I have problem on it, uhmm.. for example: virus, or corrupted operating system, all I do is to format my laptop or recover it using system recovery from the hard disk or using recovery disc which is inserted in the DVD drive. But, recently I'm having a problem with my laptop. My problem starts after I compressed the Drive C:, but I don't think that may cause the black screen problem that I'm encountering since then.
Here goes my problem: When turning on my laptop, the first thing I can see is the "TOSHIBA" logo and then after it fades it just gives me a black screen. I don't know why it's just black screen, perhaps its system has been corrupted. I've tried using the system recovery for the Nth times, but sadly the ability to run the system recovery from the hard disk partition also FAILED and just gives me a black screen again. When pressing "number 0" it does not direct me to the recovery features of the notebook but instead it only put me on a black screen. Likewise when I use the recovery disc, it also put me on a black screen upon entering in the DVD drive, and so as when I'm trying to reformat my laptop with Windows7.
I can't even access the safe mode options of my notebook. All I can access is the CMOS/BIOS setup features of the notebook when pressing F2.
Please help, I don't know what or where the problem maybe and what could be the possible solution on this. Any help is greatly appreciated.
Thank you,
Selene

selene wrote:
thanks for your input wkitty.. I have the same problem with this guy who post this > http://laptopforums.toshiba.com/t5/Video-Display/Blank-screen-after-BIOS/td-p/79923
I dont know how can i recover the the HD partition with vista installed.. do this mean I really have to send my laptop to Toshiba service center? It will cost a lot of money, my laptop's warranty already expired.
while i understand that the outlooking symptoms may appear the same, you report that you compressed your C drive but the poster in the linked thread does not... sadly, the underlying problem may or may not be the same even though the surface symtoms appear to be so...
unfortunately, i don't know what to recommend and i feel that i must leave further answers to other support members who have better knowledge than i :?
in my own case, i've finally determined that i must purchase the reload disks from toshiba and hope that they are able to restore my machine to the original factory condition... in you case, i can't say that this is the way to go or not... it really sounds like something either BIOS or OS oriented... since the BIOS reset didn't take care of the problem, it may be something deeper (ie: video broked) or something else...
have you tried booting a *nix live CD like ubuntu? the idea here is that if a live CD of another OS boots, then there may be something wrong with your HD...
along those lines, have you tried running memtest86+ and/or a HD testing util for the drive in your unit? it is possible that memory has gone uuck or the HD may have a section of bad sectors...
=================================================================================================================
I'm a user, just like you but i'm here on a volunteer basis without compensation from toshiba or anyone else... my crystal ball is in the repair shop and i cannot look over your shoulder to see what you are doing. the more specific you are, the better the answers can be

What is the technical 'cause' of the infamous iMac black screen problem?

Can anybody shed some light on what technical malfunction exactly causes the infamous iMac black screen problem? The common solution seems to be a logic board replacement. But what exactly is broken on the logic board? Is it the Geforce chip? Some kind of external driver circuitry? Or something completely different?

I was referring to the many problems also described in this thread (and also in many other places):
http://discussions.apple.com/thread.jspa?threadID=196774&tstart=0
In specific I am referring to machines where all of this applies:
- internal monitor stays black after power-on
- computer boots normally
- external display works normally
- internal display backlight works and can be adjusted in brightness, but all pixels are black
- PRAM reset doesn't help
- NVRAM reset doesn't help
- PMU reset doesn't help
- reinstalling OS / booting from CD doesn't help
- machines with this problem sent to repair come back with a replaced logic board
I'm looking for more information on the technical cause of the exact problem as stated above. So I can attempt to repair my iMac

Thunderbolt Firmware 1.1 will not update from 1.0.9 to fix Black screen problem

Can't install the firmware 1.1 fix for black screen problem. I get the following: Has anyone solved how to get around this?

Restoring often solves these problems - sometimes requiring as a new phone. The settings a sometimes data get currupted during update. If you go back in the archives of this forum, you find the same problems reported after EVERY update since the original iPhone was released.
Note that if you "modified", unlocked or hacked your phone in any way - a reason many stayed on 3.0.1 - updating USUALLY does theses things, if not completely bricking the phone.

Black Screen problem on Acer Aspire 5733Z.

The screen on my aspire stays black on switch on. I am able to use a remote monitor. On the odd occassion whilst using the laptop the screen wil suddenly come on, but does not come on again following a switch off?? I have posted this problem before, but in attempting to thank a subscriber's answer using kudus the solution case resolved ticks showed in error. Therefore I still have the black screen problem. Have tried the suggestion of uninstalling adaptor with no success. Any further suggestion much appreciated.

Barnov,
One of the easiest ways to attempt to rule out a hardware problem........is to save all of your important files to a USB backup drive. And then reset your computer to factory condition. It can be a pain to do something like that, but it can save you hours of troubleshooting.
Your computer should have pre-installed Acer software that allows you to reset your PC. There's several videos on this website and also on Acer's YouTube channel that shows you all the different ways to reset your computer.
You should also make a USB recovery drive too. It shows you how to do that too.

Fifa 12 airplay via appletv, black screen problem

FIFA12 Appletv airplay black screen problem.
Hello, i wanted to play fifa 12 iOS with tv via airplay. But it dint work, i see game picture for half second then tv goes black screen. Audio still working and game i can go to play, but i cant see the game picture. This is very sad because every other game works with tv via airplay. The only game which would be really great with airplay doesnt work :( We tested it with two different tv and two different iPad 3's. And the tv is 40" the other one was much smaller and apple tv is the newest one with newest software.
Has someone else had this problem? is the apple tv problem or maybe fifa 12 have bug or something? i hope we can get this working, iv seen fifa 12 via airplay working very nice in few youtube videos so why it doesnt work for us.
also where would be best place to contact fifa12 makers for this problem.
Sorry for my bad english, it's not my national language.

EA sent me the following anwser:
Please try any the following that you have not tried as of yet:
- Exit the game, then turn off and reset your device. Then try starting the game again.
- Ensure you are running the most current version of the game (check to see if there is an update available for the game through iTunes).
- Access the iTunes Store within your device and download the game again. It may prompt you to 'Buy' the game, but once you click it, it should allow you to download for free since you already paid for it through iTunes. Please note that we at EA have no access to your iTunes account. If you have any disputes, please contact iTunes (Apple) directly.
- Make sure your device has the latest software:
1. Download the latest version of iTunes from http://www.apple.com/itunes
Note: If you already have iTunes installed, open it and select Help > Check for Updates. Then install any available updates.
2. Connect your device to your computer with the USB cable, select your device in iTunes, and click the 'Update' button or 'Check for Update' button. Install the software update if available.

Not happy with Mac book pro retina because of black screen problem.

I am not happy with Mac book pro retina because of black screen problem. This screen failure appears after one year. I was fan of APPLE now I do no support any apple products. When they expires I will renew them with the other products belong to the other companies.

You are entitled to 90 day telephone support from Apple. Try contacting them.
Apple Support Contact
Apple Support contact - Telephone

My Late 2009 27" iMac i7 wake up problems after LION installed

About 5 or 6X, My iMac has had wake up problems after I installed LION. The screen wakes but the trackpad or mouse are frozen. I have to do a hard shut down (pressing the power button) for system to work correctly. When I power on the Mac, then everything functions. NEVER had this issue with Safari!

Exatly the same problem here with Lion on iMac 27" C2D late 2009.
more discussion about the issue here: https://discussions.apple.com/message/15757182#15757182

My iMac will not boot up. It's stuck in the black screen right after the apple logo. I ow

I Own a brand new iMac 5k with retina display. It gets stuck in the black screen right after the apple logo And all of a sudden shuts down.

You can return a new Mac within 14 days of purchase.
A new Mac is in warranty for 1 year from the date of purchase.
A new Mac comes with 90 days of free tech support from AppleCare.
AppleCare: 1-800-275-2273
Call AppleCare or take it to the Apple store to have it checked out.
Genius Bar reservation
http://www.apple.com/retail/geniusbar/
   Reset PRAM.   http://support.apple.com/kb/PH18761
Reset SMC.     http://support.apple.com/kb/HT3964
Choose the appropriate method.
   Start up in Safe Mode. http://support.apple.com/en-us/HT1564
Best.

Black screen appears after exporting to Quicktime movie

I'm having trouble exporting a time-lapse video to a QT movie. The screen is always black when I try to watch the finished product. Here's what I'm doing:
I import the jpeg files into QT 7 Pro using "Open Image Sequence." At this point I'm able to watch the video in QT. Now I want to export it to a QT movie so I can import that file into iMovie. From "File," I choose "Export>Movie to QuickTime Movie." I check the Options button to view the Settings and Size. Settings show compression is Apple Intermediate Codec, with Frame Rate set to "Current." Size is HD 1280 x 720, with the "Preserve Aspect Ratio" box checked. I give the file a name, hit "Save" and it begins to export.
When that's done, I go to my desktop and click on the newly created movie file, which opens in QT version 10.1. However, the movie shows up as a black screen.
Can anyone spot the error in what I'm doing? It's got to be something simple. I've created a time-lapse using these steps (I think) before, so I don't think there's a bug in the program anywhere. Any help appreciated. Thanks.
Btw...My OS is 10.7.4. I'm also not trying to create a movie with an audio component -- this is only video.

Can anyone spot the error in what I'm doing? It's got to be something simple. I've created a time-lapse using these steps (I think) before, so I don't think there's a bug in the program anywhere. Any help appreciated.
Not exactly an error, but I do have a question. If you are sourcing JPEG images to an image sequence file which creates a QT Photo JPEG compression file which is already import/edit compatible with iMovie and currently plays in the QT 7 Player correctly without a "black screen" problem, why are you exporting the data to the AIC compression format instead of simply saving the Photo JPEG sequence file and importing it directly to iMovie?

I bought my Mac Air 13' in August. Black screen problems constantly happens. I asked some of my friends who also use Air. They share the same experience. Overall, it is a pretty good computer. But it bothers me when I do work and it suddenly goes black.

I bought my Mac Air 13' in August. Black screen problems constantly happens. I asked some of my friends who also use Air. They share the same experience. Overall, it is a pretty good computer. But it bothers me when I do work and it suddenly goes black. What should I do about it?

without more information, I assume you mean a blackout from sleep issue.
Go to system preferences > energy settings > raise the "turn display off" setting up to as needed, say 5 mins. or 10 mins.
AND ...
unchecked the "Put hard disks to sleep when possible" in both the battery and power adapter tabs.
test it and check back

Black Screen Problem after/durning installing MSI Driver CD (ATI 4780 1 GB)

Similar Messages

Maybe you are looking for