Black screen while booting [solved]

After rebooting for the first time in a couple of weeks I get a black screen and I'm unable to do anything.
I'm using a lenovo t60 with an intel graphic chip.
Things I've already tryed:
Adding MODULES="i915" to my mkinitcpio.conf and then regenerating initramfs.
booting into arch with a usb stick and updating all packages
reinstalling udev, mkinitcpio
video=SVIDEO-1:d
I found a work around but it's quite annoying.
If I uninstall xf86-video-intel then install xf86-video-vesa then reboot and set video=SVIDEO-1:d then I'm able to boot but once I start run startx my screen goes white.
To fix the white screen I have to do everything I just said and before running startx I have to install xf86-video-intel again. Then everything works fine.
All of this makes me suspect that xf86-video-intel is the cause ( there has been an update on 2013-02-23 ) but I'm not sure seeing as I'm not an expert.
Here is a photo of my xorg.log (sorry it's a photo I didn't know about sprunge when I made it)
Last edited by 3rt (2013-03-08 20:52:57)

I had the same issue. Try installing linux 3.8 from testing, which fixed the problem for me.

Similar Messages

Upgraded to Maverick, now MBP 2011 has black screen while booting

I just upgraded from Mountain Lion to Maverick, and I am already regretting it. Upon installation, my MBP (2011) was running slow, so I restarted it. Now, when my Mac is trying to boot, the brightness is at (roughly) 25%, and I can barely see what's happening. It looks like the loading cursor is present onscreen. The good news is that I can hear the startup chime. However, after 10-15 seconds, the screen fades to black. When I press any key, I can hear the default error sound. I tried Command+R, but that didn't do anything. Any help would be greatly appreciated!

Not sure what happened. Upon the umpteenth time restarting the laptop, the scree is now at 100% brightness. I was able to log in as well. All is good.

F.E.A.R. 2 black screen while using Soundblaster X-Fi

This is my second attempt to get some support for a problem that is plaguing many trying to play F.E.A.R 2 with a Soundblaster X-Fi. We have been on the official forums for WBGames now for the past two weeks asking for help. Many were able to find solutions by updating their codecs however there are many of us that still cannot get into the game. WBGames official response it as follows...
Dear, xxx
Regarding your sound acceleration error and the sound cards you have used, we apologize for the inconvenience you have experienced.
At the moment, we have been noticed that certain Creative sound cards (X-Fi, Sound Blaster and Audigy) and Realtek are presenting incompatibility issues with the F.E.A.R. 2 application. Unfortunately, Creative Labs have not yet released a patch to solve this situation, as other companies like Nvidia have worked on.
F.E.A.R. 2 is designed to function with Windows XP/Vista compatible graphics and sound cards. Drivers for these devices are provided by Windows itself or the respecti've card manufacturers and may occasionally result in incompatibility problems beyond our control.
If there is anything else we can do to assist you, please do not hesitate to contact us by email at [url=mailto:[email protected]">[email protected] m[/url] or by phone 080-0664-9456 (in Germany) during the hours of EST :00 pm - 0:00 pm, PST: 0am- 8pm MON-FRI.
Thank you for contacting Warner Brothers and have a great day.
Refund option
If you are not satisfied with the performance of this product on your PC, you may return it with the receipt of purchase to the store from which it was purchased within 90 days from the original purchase date for a refund.
If you purchased this product as an electronic download, please visit the following site for refund details:
[url="https://support.steampowered.com/kb_article.php?ref=4938-WTDF-9465">https://support.steampowered.com/kb_...4938-WTDF-9465[/url]
I thought that someone with creative labs would be interested in either responding or releasing some kind of a statement in regards to this.
The current problem for us is when we try to launch the game a small animated orb runs at the bottom right of the screen while the game loads. At the end of the animation we hear a small chime and the screen goes black as though it is about to load the intro videos. But we get nothing. The screen remains black. I have exhausted all of their solutions, I have updated drivers and tried the latest beta drivers from Creative. I have removed, replaced, and updated codecs. Video card drivers are updated, etc.
Basically we are faced with the following dilema. We can disable the sound card in Windows and the game plays however with no sound. We can run the game in safe mode which manually disables the sound card and the game plays but with no sound. Leave the sound card enabled and run the game in normal mode and we get a black screen.
PLEASE, can someone with Creative Labs respond to this? We are looking for answers and would very much like to play this game.Message Edited by djdouglas on 02-20-2009 09:39 [email protected]

Re: F.E.A.R. 2 black screen while using Soundblaster X-Fi?
solace wrote:
Pardon me but i'm looking your Quad SLI setup a potential culprit to your problems. Have you tried disabling SLI mode to see if the problem can be resolved?
That was my first thought when I encountered this problem. I took the steps troubleshooting video. Disabled SLI, Physically removed one video card. Updated drivers, etc. I am currently running the 82.06WHQL drivers which are suppose to be enhanced for F.E.A.R.2 and other games.
My next step was to try uninstalling codecs as their support team had suggested for people running into issues with the demo version (which btw worked perfectly for me). There were tons of reponses by the devs and community managers before the release of the game in response to people having issues (these same issues) on the demo. So they released a patch the day before the release of the game and when everyone installed the game the patch automatically installed. So for me and many others that enjoyed a smooth gameplay in the demo our rigs are now not working with the official release.
Since release we have yet to see a response or fix or suggestion from a dev. There have been many others in the community that have helped each other out by posting their solutions. For most updating their codecs using Klite or Ace Mega codec pack has fixed their problem but for a select few of us these solutions have not worked.
Basically I can launch the game successfully in safemode which disables sound. I can also disable the sound card and launch the game successfully although without sound. The codec that has seemed to be effecti've when replaced by others is the Microsoft IMA ADHCP codec. However for me I can disable that codec and get a hardware accelration error but still get a black screen. Re enable it and get black screen with no error. So I do not believe this to be the issue plaguing me. Ultimately it is coming down to a conflict with my sound board and the game.

Mac Pro intermediate black screen at boot after installing mountain lion

I have a 2008 Mac Pro tower, but since installing Mountain Lion I now get a random black screen at boot. Unplugging the apple cinema 20' power supply for 15 minutes seems to clear the fault. Have had no such problems with other OS until Mountain Lion, seems OK when booting to Snow Lepoard on my other drive?
Anyone have the same fault?

Thanks for trying the help! I tried every version of start up, but with no screen it was no good..
Finally solved the problem, it was the ATI HD 2600 XT graphics card that was dying a very slow death.
Replaced it this morning with a GT120 Nvidia.
Anyone with this card should Google it, as apple did a big recall on these..
http://www.itproportal.com/2011/02/21/apple-extends-warranty-mac-pro-video-cards /

Win 7/Z580: Black screen on boot up, before login screen?

Win 7/Z580: Black screen on boot up, before login screen?
=======================================
I find some interesting posting in this forum. Thanks for keeping this forum to help windows/Lenovo community. I like to pick up the brain of this forum to resolve the black screen issue. I am not sure, whether it caused by virus. I use Microsoft Security Essentials. I am not able to run this in command prompt.
I started my laptop this morning & login screen showed up. Once I entered my login credentials, I heard the sound that usually plays once a login is successful, but I ended up with a black screen. After this occurred, I had to hold down the power button to manually shut down the computer. Once I started it up again, I was prompted to do a system repair, which eventually ended up with all successful outcomes, but I now have a black screen with a cursor before the login screen now. I have no idea what caused this to happen. My laptop is a Lenovo Ideapad Model Z580 (500 GB HD, 6GB RAM).
I am not able to get into safe mode or any other mode, which all leads to a black screen described above. I am able to use the "Repair Your computer" tools after pressing F8 during booting only . All other options leads to Black screen with cursor in the middle
Last Known Good Configuration leads to same
Enable Low Resolution Video (640x480) leads to same My Z580 is not responding to CTRL+ALT+DEL Windows Logo keys as well.
**** I tried SAFE Mode. It loaded couple of drivers and paused at CLASSPNP.SYS load. It went to Black screen with cursor at center.
I am able to invoke control pannel from Command prompt of working PC by typing control.
Z580 PC is not responding to control from command prompt (under Repair Your computer) either.
Z580 is able to use the "Repair Your computer" tools after pressing F8 during booting .
Under local user login it provided Start Repair option. As I pick this option, I got the following. Problem signature
Startup repair offline
1 - 6.1.7600.16385
2 -
6.1.7600.16385
3 - unknown
4 - 21200332
5 - autofailover
6 -
4
7 - NoRootCause
os v - 6.1.7600.2.1.0.2561
locale id – 1033
Under Admin user login, it provided system recovery options. It is not picking up the recovery point created a while ago.
Windows Memory Diagnostics is not launching and shows a black screen without cursor.
I am able to get into command prompt. I tried the following there.
I am not able to run cmd as admin
I reviewed the past posting of this forum on this subject.
Windows 7 boots to an unresponsive black screen with mouse cursor...
System File Checker: Run sfc /scannow & analyze its logs in Windows 7 / 8
Windows Resource Protection could not start the repair service
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program generates in Windows Vista
Force SFC to Run in Windows 7
Windows Resource Protection found corrupt files but was unable to fix some of them
SFC /SCANNOW showed up
"Windows Resource Protection could not start the repair service
I did "net start trustedinstaller"
"Windows Resource Protection detected pending repair restart the computer"
I ran repair options using sfc /scannow /offbootdir=x:\ /offwindir=D:\windows
and got "Windows Resource Protection found corrupt files but was unable to fix some of them "
I did findstr /c:"[SR]" %windir%\logs\cbs\cbs.log >sfcdetails.txt I will be glad to attach the zip file that contain CBS.LOG & [SR] tag extract (xxx.txt).
I did not any find ERRORS there, SFC ended with message saying "found corrupt files but was unable to fix some of them" . It is misleading. There is no [SR] tag pointing to corrupt files. Does SFC through false positive like this?
I ran chkdsk. ResultsFile verification completed.
0 bad file records processed.
0 EA records processed.
CHKDSK is verifying indexes (stage 2 of 5)...
Index verification completed.
0 unindexed files scanned.
0 unindexed files recovered.
Windows has checked the file system and found no problems.
0 KB in bad sectors.
Failed to transfer logged messages to the event log with status 50.
It is puzzling me.
Thanks for helping.

I tried these steps 8/7/2015. I ran chkdsk. Results for D:\
File verification completed.
0 bad file records processed.
0 EA records processed.
CHKDSK is verifying indexes (stage 2 of 5)...
Index verification completed.
0 unindexed files scanned.
0 unindexed files recovered.
Windows has checked the file system and found no problems.
0 KB in bad sectors.
Failed to transfer logged messages to the event log with status 50.
Updated on 8/7
============
Here are my HDD config:
Volume ### Ltr Label Fs Type Status Info
Volume 0 F WDO_Media64 UDF DVD- Healthy
Volume 1 C NTFS Partition Healthy
Volume 2 D Windows7_OS NTFS Partition Healthy
Volume 3 E LENOVO NTFS Partition Healthy
Volume 4 G FAT Removable Healthy
Volume 5 LENOVO_PART NTFS Partition Healthy Hidden
I ran CHKDSK /F /X for C, D, E. All resluted to "Windows has checked the file system and found no problems."
F8 ===> Repair Computer===> Command Prompt ===> Works OK
F8 ===> Repair Computer===> Start up Repair ==> Results into "Startup repair could not detect a problem"
F8 ===> Repair Computer===> System Restore ===> "No restore points has been created on yout computer system drive"
F8 ===> Repair Computer===> System Image Recovery ===> "Windows cannot find a system impage on this computer"
F8 ===> Repair Computer===> windows Memory Diagnostiyics ===> "Black screen with Cursor in the middle"
After getting into Command prompt
I run net user
User accounts for \\
Administrator Guest
The command completed with one or more errors
It did not list other users in my laptop. I do not know why? I tried under F8 ===> Repair Computer===> Command Prompt ===> Works OK
Here is the result:
- Boot with Last Known Good Configuration (F8 menu) ===> Black screen with cursor in the middle
- Restore to a prior date (System Restore) - System Restore ====> Already reported in previous reply
- Try a clean startup Troubleshoot Application Conflicts by Performing a Clean Startup results in
Clean Start up
D:\Windows\System32>runas /user:administrator msconfig
Enter the password for administrator:
Attempting to start msconfig as user "MININT-84TH5FG\administrator" ...
RUNAS ERROR: Unable to run - msconfig
1060: The specified service does not exist as an installed service.
- Try loading defaults in BIOS - F2 ==> f9 ==> f10 ===> Black screen with cursor in the middle
Check if explorer.exe is running and start from CTRL+ALT+DEL (task manager - new task) ===> CTRL+ALT+DEL not responding
Is anybody in this forum point me to fix? Thanks for looking into this issue.

Familiar Story - tx2000 - lights and fan on, but black screen at boot up

I've been reading around that there's a common problem with the 1000 series of tablets. After 1 1/2 years, the sucker gets a black screen at boot up, yet the lights are on.
Well, almost a week to my tx2000's 1 1/2 year date (and now out of warranty), I tried to take my tablet out of hibernation. The screen was black yet the lights were on and I could hear the fan.
I tried basic troubleshooting with the online tech, but to no avail. It doesn't work, and they tell me it'll cost about $400 for it to be picked up and repaired. Anybody got a viable solution, or do I just need to go ahead and start saving for a Mac?
Thanks HP for reselling such faulty merchandise.
http://www.mycheaplaptop.net/2009/03/never-buy-hp-laptop/

So this most likely does not apply to the tx1000 problem, but I believe the tx2000 recent problem is not related.
For those getting lights and fan on.. or perhaps on for a second or so but no boot screen or logo it maybe related to your video card driver.
Sounds crazy right? Well your video card driver controls how your computer goes into hibernation and sleep. If the drivers are incorrect the system may not handle this process correctly when you try to reboot it.
I'm not certain on how to get the system to boot up again, but I've done it quite a few times while trying to revive the machine.. pulled the battery.. the ram.. held the power button.. lots of cussing.. the solution seemed different each time, but eventually if you can get back into windows you'll find that either by not using hibernation/sleep or by loading the original video card drivers from the hp site, you'll avoid this problem again.
This problem started occurring for me after microsoft made available a driver update on windows update this past summer.. then suddenly everyone started having issues at the exact same time.. I've seen it blamed on simultaneous heat issues around the world caused by exactly 1 year and 2 months of dust collection on every tx2000 laptop... however I'm quite certain it's the new video drivers in combination with hibernation/sleep.
But don't take my word for it. For more information on how video drivers can affect the boot process check this site: http://articles.techrepublic.com.com/5100-10878_11-1046825.html

R7870 TF III 2GB OC edition Black Screen while gaming (Guild Wars 2)

Hello there mate,
1st time post for me,
i'm from Indonesia, and i just got my r7870 recently
and i'm using it now for playing Guild Wars 2.
1st i'm using the "auto detect" mode in Guild Wars 2
where give me "high" setting for the graphic
but after a few minutes i got a black screen.....
that force me to shut down my system by press and hold the power button,
then i try with "low" setting for the graphic (in Guild Wars2)
but still got the black screen after another few minute..
and i'm using CCC ver. 12.8
i have been search and found some post with similar issue with this (black screen while gaming with r7870)
what can i do to solve this prob ?
Note : before using r7870, i used r4870 1GB, and have no problem playing Guild Wars 2 (in low setting)
here is my rig :
Main Board : MSI - Z68MA - G45
CPU : I3 - 2120
RAM : 2x4GB GSkill
PSU : 650 Watt Seasonic
HHD : 2x 500gb Seagate
Graph Card : MSI - r7870 TF3 OC edition
sorry for my bad English, hope you all still can understand.

Quote from: Svet on 08-September-12, 07:20:56
have you tried msi vga drivers for your card?
do you have such issues elsewhere?
well i haven't tried using the drive that come within the bundle yet
but as i mentioned before, i did not have any problem playing GW2 and other games
with my previous card (4870) and using exactly the same rig,
so i don't think the problem lies elsewhere,
but i think ill try msi vga driver that i got in the cd 1st,
thanks for your suggestion, ill report again the result later.
tried the msi vga drive (ver. 8.95) that come within the budle
and well... still got the black screen problem.. (tested with guild wars 2)

970 GAMING black screen when boot on cold start, have to clear CMOS everytime

I have 970 GAMING w/ FX8320, it shows black screen when boot on cold start, have to clear CMOS everytime to enter default.
I have updated it to the up to date M11 bios. Once it boot up, it functions OK no matter whether you reboot or reset it. But after turned off a few hours (cooled down), it shows on black screen again on boot, all LED lights up OK, but I can hear the fan like keep rebooting, any idea?
PSU seasonic 430W, GPU HD7750.

In what DIMM slots did you insert your memory? I just got and at this moment building a new computer with a 970.
A horrible experience I had with my last build reminded me of it. My board was am MSI A88XM-E45. DIMM1 is blue, DIMM2 is black, DIMM3 is blue, & DIMM4 is black. When using two sticks of RAM, it says to install one on DIMM1 & the other in DIMM3 (Makes sense... After all, it's color colored that way).
Well it would not boot. I reseated every component and for HOURS tried almost everything. Finally I decided to place my two sticks of RAM in the first two DIMMS and viola!
I think I will begin this build the same way.

Black screen on boot & Diagnostic errors

Hi,
I've a HP g62 notebook pc that has some problems when is booting.
Sometimes the screen is black when i try to boot or i've a BSOD related with the atikmpag.sys.This PC doesn't have warranty, but i don't know if the problem is only because of the SO or if there is any hardware failure.
The PC model is the: g62-b10sp. Product id XF293EA#AB9
System ID 143A
I tried the HP diagnostics wich I retrieved the some test menssages: Memory Test: PASSED
SMART CHECK : PASSED
Short DST : PASSED
Optimized DST : PASSEDHard disk test: PASSED
Battery Test : Primary - Replace
Failure ID: MBQ3W8-5667NG-9XL03F-C0F403 Start-Up Test : FAILED
Failure ID: MBQ3W8-5667NG-9XL03F-X0F403 Run-In Test: FAILED
FAILURE ID: MBQ3W8-5667NG-9XL03F-C0F403 System Tuneup: FAILED
FAILURE ID: MBQ3W8-5667NG-9XL03F-C0F403
Someone from the HP support team could help me?
I wanna know what those failures id are related... They are failures from motherboard/graphics?
Thank you for you attention
Best regards

Hi , Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!
I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your HP G62-b10SP Notebook and an Black screen on boot showing. Thank you for the error messages and the explanation. Very helpful in diagnosing the issue. The first error Battery Test : Primary - Replace
Failure ID: MBQ3W8-5667NG-9XL03F-C0F403 the Real Time Clock battery needs to be replaced. All the others are the same error message as one can not perform as the Real Time Clock battery needs to be replaced. I recommend to replace the Real Time Clock battery and run the tests again. Here is a link to show you the part number and what you need to do to replace Real Time Clock battery. Page 51 for the part number and shows you how to replace it. I hope this helps, please let me know how it goes. Thanks.

Black screen while working

last few days my mac got a black screen while working once ort twice a day. no idea why. it's only the screen and there is no way to wake him up. but the cpu didn't shut down and it sounds like he is working correctly. any idea? would make me happy!

Hey enderci,
Thanks for using Apple Support Communities.
If you are not getting video, this articl has as section for no video that should help.
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573#1
Have a nice day,
Mario

Black screen at boot MSI Z77A-G43 with HD7850

Hi,
I've tried everything You suggested in this topic. I've upgrade and downgrade bios (official 2.3, 2.4, 2.8, 2,9 / beta 256, 281,296) few times but still is black screen at boot. Now i'm on the newest beta bios 296 and still same issue on Sapphire HD 7850 with my Z77a-G43 board. I know for sure that sapphire working well because I've checked on other mobo with even worst PSU (400W instead 550W Volcano). Before hd 7850 I had gtx460 and swith those few times and always gtx460 works fine, so I don't understand anything right now.
Tried different slots, also clear cmos.
Board: MSI Z77A-G43
Bios: Version 296
VGA: Sapphire HD7850 1GB
PSU: Modecom Volcano 550W
Intel Core i5-3570k
MEM: Kingston 4GB 1600MHz
HDD: 2xSSD
Without OC
OS: Windows 7 64bit Professional
Can You help me somehow, maybe I did not check something else?

Quote from: The CPU Whisperer on 22-April-13, 16:06:05
Do you see the same problem on bios 2.90?
The Z77A-G43 seems the have difficulties accepting HD7xxx AMD VGA cards lately.
It seems that the problem is gone. I thought of it being an ATI driver issue ~ but not even the latest didn't fix it. But since I flashed to BIOS 2.9 I haven't encountered the problem anymore. So I believe something is fixed between 2.3 to 2.9.
However my problem was a bit different that the OP has.
Oh, and I said this on other thread so I say it here too: MSI and Asus 7xxx cards haven't faced the kind of issues Sapphires are having. I'm so glad to my choice... as I almost picked Sapphire but then read comments on Newegg which weren't in favor for Sapphire.

S930 stuck at Lenovo screen while boot up.

My S930 stuck at lenovo screen while boot up.
I tried to leave the phone while waiting for it to boot until the battery drain out.
Then charged till full , try to boot again and it still stuck at the same lenovo screen..
What to do? How to reset / factory default ?
Please help. TQ

Issue :- G500 Lenovo laptop screen gets stuck at lenovo screen and does not allow to do any thing alternatively need to power off laptop.
I am also having this same problem occasionally. In that case if my screen stuck at lenovo screen then I turn off my laptop, After while when I turn it on then problem go off. But today same method did not help me, finally I removed my batter for a while then plugged it again which again resolved the issue.
I purchased my G500 lenovo laptop 4 or 5 months ago , it had been working fine for first 3 months but after it I encountered with this probelm.
I updated my bios with latest available version but that also not helped me
My concern is that why this problem is occuring occasionally. Request you to share valuable steps and guide us to get rid off from this problem.
Thanks and Regards
Ashok Dewan

Quad Channel RAM Black screen on boot

So i can run my computer with Duo channel RAM DIMM slot 1 & 3, but if i add DIMM slot 5 & 7 my computer screen just stays black forever. the computer starts up and stays powered on, but no signal to screen. i have tried all 4 ram pieces alone in DIMM slot 1 and the computer boots just fine and it says 4gb ram in both BIOS and my computer properties. I have also tried just adding just one ram piece in DIMM slot 5 and the same problem occurs, just a black screen on boot.
my specs are:
MOBO:MSI X99S SLI PLUS, Socket-2011-3
ATX, DDR4, 4xPCIe-x16, USB3.0, SLI/CFX, M.2
CPU: Intel Core i7-5820K, Socket-LGA2011-3
6-Core,3.3GHz,15MB,140W,22nm,28 PCIe lanes,Haswell
RAM: HyperX Predator DDR4 2133MHz 16GB
4x4GB, DDR4 Non-ECC CL13 DIMM (Kit of 4) XMP Preda
GPU: MSI GeForce GTX 980 Gaming 4GB PhysX
PSU: Cooler Master GX 750W PSU
ATX 12V V2.31, 80 Plus Bronze, Standard, 4x 6+2pin
I have Flashed the BIOS to 1.5, swapped around on the RAM pieces to no avail.

Quote from: badboy2k on 24-December-14, 13:20:22
some people are having problems with that board! (no idea what is going on with it)
just for the sake of problem checking can you take out your CPU and look at the pins in the cpu socket with a bright light and a magnifier (check multiple angles) to see if any of the pins are bent?
a few of the pins are indeed a little bent out of position, would it be best to return the board or should i be able to bend them back into the correct position?

Black Screen on Boot using mac pro os snowleopard 10.6.6

I get a black screen on booting my macpro with os 10.6.6 after the booting is done the screen activates automatic. i do hear the startup sound but dont get the startup screen with the apple logo.
also my mouse does strange things like not responding on a mouseover juming around the screen and pressing buttons i don't press. Never had these problems before until this morning whenn i booted my mac pro. Please help

Could be your monitor power supply is going. could also be 10.6.6 so first try to get back to a OSX which did not give you problems.

Fixed black screen on boot, passwords not working now

After fixing black screen on boot with the advice provided by the great community. (Here: https://bbs.archlinux.org/viewtopic.php … 9#p1501989 )
I followed the method outlined in the post I reference. Booting from live USB, mounting my root home and usr partitions, arch-chrooting into the root partition and then setting modeset=0 in radeon.conf and putting radeon in MODULES in mkinitcpio.conf then running mkinitcpio -p linux. Afterwards I exited the chroot and unmounted all partitions.
This fixed the blank screen, but all of my passwords are changed. The root and my user account passwords don't work. So again I booted into hot usb, mounted partitions, arch-chrooted in, and ran passwd to change root pw and then su to get to my user account to run sudo passwd. After doing so, I exit the chroot and try to unmount the partitions. I can unmount /dev/sda2 (home) but no sda1 (root) or sda3 (usr). It says: cannot umount /mnt/arch target is busy or cannot umount /mnt/arch/usr target is busy. It suggest lsof(8) or fuser(1) but either I use them wrong or they don't help. If I just reboot at this point my passwords still don't work. Why can I not unmount usr or root partitions? It says they're busy but ps -ax shows nothing. Any ideas? If more info is needed I will promptly supply it, I want to get my arch box up and running again asap
Take care fellow archers

Forgot to mention when I boot into Arch normally, it does systemd-fsck on all the partitions they all pass but after checking /dev/sda2 (home) it freezes. The messages displayed are:
running hook [udev]
Triggering uevents
performing fsck on /dev/sda1 /dev/sda1 clean xxxx/xxxx files, xxxx/xxxx blocks
mounting /dev/sda1 on real root
running late hook [usr]
mounting /dev/sda3 on /usr
running cleanup hook [shutdown]
running cleanup hook [udev]
Welcome to Arch Linux!
kvm: disabled by bios
systemd-fsck[252]: /dev/sda2 clean, xxxx/xxxx files, xxxx/xxxx blocks
and it freezes here if I switch TTY's none of my passwords work.
Thanks in advance
Last edited by cshenkan (2015-03-03 04:37:00)

Black screen while booting [solved]

Similar Messages

Maybe you are looking for