Blackberry 9320 broken,9360 on the same route due to "battery to low for radio use" etc

My previous blackberry 9320 ,which I can't use anymore, aswell as my 9360 that's on the same route as the previous one started out in the beginning with
-battery to low for radio use(which I would turn back on)
Later my memory card couldn't be recognized, after some attempts of "fixing the broken files" as the phone would say, and then "repairing failed"
Problems got worse ,as if I allready can't use a memory card because all 3 got broken somehow,but after that it started saying "battery to low for radio use" then my battery would in a matter of seconds drain and then a message I get atleast 30 times a day "battery drained,shuttingdown handheld". It gets worse, then it says the same message ,but only this time the battery is full, because the phone must be pluged in too a charger to be able to start, and as I call it, then has to be on "life-support"(charging like 24/7). These problems seem to be activated by high radio use or just plainly to irretate a person. I'm very dissatisfied with blackberry and I seek answers. now here comes the catch, I took my previouse blackberry,the 9320, in 2 times to get the software updated and the last time they couldn't say why this is happening , aswell as try putting another(new) blackberry 9320 battery in the phone. It worked for 3 days,no kidding, and the same problems in their stages began.I fear my blackberry 9360 is on the same route and I'm dissatisfied with these products for its expensive and causing trouble. Please help me resolve this problem ???p.s both phones were newly bought since they are contract phones.

Hi and Welcome to the Community!
Given that you've already begun formal service for this issue, I recommend you continue with that. After all, they said it was fixed, but it's not...don't you want to challenge them on that fact?
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Similar Messages

"Battery too low for radio use" - Curve 9320

Since early on my curve 9320 has given me a "battery too low for radio use" warning at very random moments often times when the battery is still halfway into the white area. Sometimes this can be reset manually in the setting by turning radio back on, however this does cut into calls, messages and other activities.
I have changed the battery recently thinking this was the cause of the issue, however this did not help. I am still getting the error...not to mention the short battery life of this device...this is very frustrating.
Is this a common problem and if so how is it solved? Any help is appreciated!
BV

Hi and Welcome to the Community!
Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain directly connected to a known-good wall charger (not PC USB, not a cradle):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs.
It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem. Note carefully please that "new" and "know good" are not necessarily the same things. While rare, a "new" battery certainly could be defective. Rather, the simplest (and least costly, btw) method to conduct this test is to find someone with an identical BB who has no issues...trade batteries and see what happens.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Blackberry curve 9320 batt too low for radio use

I have had this fone since june and have constantly had probs with the battery life.its now sayin battery is too low for radio use even when there is half a white bar.keeps cutting out during calls.I've constantly got to do a battery pull!any ideas??

Hello guys,
I found the solution! I have 2 9320 and both developed this problem after 5 or 6 months. Battery too low for radio use even if nearly fully charged. I tried everything what described here- battery pulls, soft reload, deleting apps, pulling battery out with charger connected- nothing worked- just dont waste more time. The solution is easy and its not software problem! Just open your phone- if you dont know how check on youtube so you don't damage your phone and simply clean battery connector in a place where it is touching the mainboard. My bb board was black in that place- came off easily and connectors on mainbord looked like new after. I used zippo lighter fluid and clean cloth. Since then no problem on both my blackberries- never switched radio off again with battery not beeing red. I think there was not enoug power flow through this connector causing me going crazy. Now my blackberries are amaizing again! Hope it helps!

I have an IPA2 wifi 3g working fine with wifi up for 3 monthes then from two weeks it get connection but after 1 minutes stop to serf/download with signal and connection always present. With the same router are still connected others 3 pc working!

I all,
the scenario is the following:
WIFI connection with TISCALI operator. Encryption made by WPA2 EAS with router SITECOM or tested also with another router DIGICOM with WPA TPK.
From December up to end of March the IPAD2 working perfectly serfing and downloading.
By two weeks it has a very strange behavour without have changed any configuration on IPAD or network:
with WIFI turned on it discover about 4 different ntw among them the mine, I successfully authenticate with psw the my ntw,
the IPAD2 start to run with Safari without problems, but after about 1 minutes, it stop to serf or download and answer that the Server cannot be reached or the page cannot be open, at the same time the signal is present on the icon of WIFI and it is strong.
This problem is systematic: If I dissasociate the ntw and then authenticate again I start to serf again for 1 minutes (more or less) and then it stops again, this occurs every time I authenticate the ntw after a disassociation.
I made some test changing the encryption from WPA2, WPA and also without encryption but the result was always the same, after about one minute the server seems to be for the IPAD2 no more reachable while the others PC and netbook connected to the same router continue to serf/download without problems!
I also tried to change the router with a DIGCOM that I did not use generally, but the behavour is always the same.
Since the IOS was the 4.3 revisin, I made the upgrade by means Itunes to IOS 5.1 succesfully installed.
But unfortunatelly all test repeted have had the same negative result with the same behavour!
Yesterday I tried to do the complete restore of the System but the tests had the same rsult.
I really don't know how to proceed, the problem started suddenly without any action from my side....is there someone that can help me?
Thanks Massimo

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
 Cheers, Tom

Home Sharing not working between wireless PC's / devices and ethernet wired PC's on the same router.

Home Sharing is not working between wireless PC's / devices and ethernet wired PC's on the same router. I installed a new Verizon FIOS ActionTec MI424WR GigE wireless / ethernet router, replacing the original FIOS router. With the old router Home Sharing worked fine across and among all iOS and Windows wired and wireless devices. With the new router Home Sharing works between and among the Wired PC's but not between the wired PC's and the Wireless connected PC's or iOS devices. Home Sharing also works between and among the wireless connected PC's and iOS decices but not between them and the wired PC's.
Only the router was changed. No changes were made to any of the devices except all were updated with the latest version of iTunes 10.7.0.21 and the iSO devices were updated to iOS vrsion 6.01. Three PC's are wired and all are running Windows 7. There also is a Windows Home Server connected to the router by ethernet port. It does not run iTunes but does provide WebDAV services to my iOS devices. This works fine. Two PC's are wireless, one running Windows 7 and one running Windows 8. All of the PC's are connected to the same (new) router via it's ethernet ports and it's wireless access point. Two of the wired PC's are connected via a high-speed ethernet hup that is connected to the router (Home Sharing works fine between the two PC's on the hub and the PC on the router). All wired and wireless devices on the router are visible and members of the router's Home/Office virtual network.
All of the PC's are visible in the Windows network and all shared files are accessable from all PC's, both wired and wireless.
Obviously the router seems to be the issue, something between the ethernet and the wireless access point components. I checked the settings and found nothing that would prevent Home Sharing between the wired and wireless devices. There is no setting that isolates the wireless network. I have done the following:
Read the router user manual and checked all the settings
Rebooted the router and tested.
Turned off the router's firewall and tested.
Home Sharing is turned on all the devices and all use the same Apple ID.
Restarted iTunes and tested.
Verified iTunes is "Allowed" in each PC's firewall.
Again, I can Home Share between the two wireless PC's but not between either of the wireless PC's and any of the wired PC's. I can Home Share between my iPads and iPhones and either of the two wireless PC's but not with any of the wired PC's. I can Home Share between any of the wired PC's but not between any wired PC and a wireless PC or iOS device.
I hope someone may have had a similar problem and has a fix suggestion. I'm stumped! I have a;so contacked ActionTec and awaiting an answer.

Solution from ActionTec is:
Log into your router.
Click the Advanced icon
Cclick Yes
Click on the IGMP Proxy
Select Disable
Click Apply

Using ipad2 and airplay with appleTV; can I have the ipad2 on wifi and the AppleTV on a wired port of the same router in order to use airplay?

can I have the ipad2 on wifi and the AppleTV on a wired port of the same router in order to use airplay?

I belive you can, I think my friends Apple TV is connected to their internet via an Ethernet cable, and we use Airplay sometimes using our iPads that are connected to the same network via WiFi. It should work as long as they are both connected to the same network. However, I don't have an Apple TV of my own, so don't take this as a solid answer.

Can an infected XP system infect a Win7 computer on the same router.

Hi there....
I was just wondering if an XP system, once infected, can infect a Win7 on the same router. I know support for XP is dead, but I can't afford to upgrade the OS on the old XP system at this time. I have all available XP updates and Win7 (just did a full format,
and reinstall of XP).
I have no network set up, they are just on the same router, both on a cable, not Wi-Fi.
EDIT: Sorry for posting in the wrong forum....Please move, need be.

I am currently using AVG anti-virus on both machines.
Would that replace it? Or should I use both on my Win7 system?
I am a gamer, how does it affect gaming? If, at all. AVG has a gaming mode that limits its interference with games.
Thanks for your help!

(PBR) set next-hop to the same router?

Hi
I need to send some traffic to an external L2 device, and then get it back, to the same router.
I planned to use PRB, to set the outgoing interface, and the next-hop as the IP address of the incoming interface, from the same router.
Is that possible?
Can I set as the next-hop an IP address from the same router, forcing the traffic to go out, by specifying the outgoing interface too?
Thanks in advance
JM

JM,
Good catch, I did try the command on a router today, and it did show up in the running config. Its indeed a warning message, but I m not sure whether the router will route packet to itself..if I get some time today i will test it out.
Sankar.

When I share a video with fcpx and it goes to Quicktime, the last few seconds goes mute. I checked the clip and sent that the same route and all is fine. It is only when I send the whole 3gb video. Any ideas?

When I share a video with fcpx and it goes to Quicktime, the last few seconds goes mute. I checked the clip and sent that the same route and all is fine. It is only when I send the whole 3gb video. Any ideas?

paul71054 wrote:
... Any ideas?
add a few seconds black to your project.
Try again.
could be some really weird codec problem, with 'cut' GOPs', .. somethin'...

Hi i am working on my web site and it appears to have blocked the ip from my server i can't open my web sites and i cant open the server home page but can do this on my iPhone i have trend micro running on 2 other desk tops all from the same router please

Hi i am working on my web site and it appears to have blocked the ip from my server i can't open my web sites and i cant open the server home page but can do this on my iPhone i have trend micro running on 2 other desk tops all from the same router please help maybe its a firewall? Cheers Dave

All I can suggest is that you open that file on the MBA and save it as a new file, then see if you can open the new one on the iMac.

Why my iphone 4 connect to wifi, but when i open safari and search something it say i not connect.. but in the same house my sister using iphone4 too but she can online with the same router

why my iphone 4 connect to wifi, but when i open safari and search something it say i not connect.. but in the same house my sister using iphone4 too but she can online with the same router. i go and check over the detail of the network i connected, over the ip address and subnet mask have the numbers, but over the DNS and router don't have any number...isit the problem???? i can online at any other place but just my home cant...y????

Hey confuddled_chica!
Try the steps in the article below to troubleshoot this issue:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
Thanks for being a part of the Apple Support Communities!
Regards,
Braden

Using Crypto Maps and IPsec Static VTI's on the same router

Is it possible to configure both crypto maps and IPsec static VTI's on the same router? What platforms have this capability? What IOS version do I need?

Yes you can and as far as I know I dont think there is a hardware dependency.
VTI mode 'tunnel mode ipsec ipv4' was added in 12.3(14)T.
If you are mixing tunnel protection and crypto map ensure you use iskmp profiles to differentiate somehow that the tunnel IPSec connection is not prcessed on the crypto map!
Here is a rough example (fine tune it as needed):
crypto keyring key1
pre-shared-key address 1.1.1.1 key test123
crypto keyring key2
pre-shared-key address 7.7.7.7 key test777
crypto isakmp profile vpn1
   keyring key1
   match identity address 1.1.1.1 255.255.255.255
crypto isakmp profile vpn2
   keyring key2
   match identity address 7.7.7.7 255.255.255.255
crypto ipsec transform-set test esp-des esp-sha-hmac
crypto IPsec profile vpn-tunnel
set transform-set test
set isakmp-profile vpn1
crypto map mymap 1 ipsec-isakmp
set transform-set test
set peer 7.7.7.7
set isakmp-profile vpn2
match address 177
interface Tunnel0
ip address 10.0.51.217 255.255.255.0
tunnel source 2.2.2.2
tunnel destination 1.1.1.1
tunnel mode ipsec ipv4
tunnel protection ipsec profile vpn-tunnel
interface Ethernet4
ip add 2.2.2.2 255.255.255.0
crypto map mymap
Regards,
Uwe

What can I expect of my 4s with wifi connectivity. My 4s receive a signal from the same router I have always used. My 3G would pick up a signal throughout the house, and my 4s won't allow me out of the room. Is my new phone defective or just inferior.

What can I expect of my 4s with wifi connectivity. My 4s receive a signal from the same router I have always used. My 3G would pick up a signal throughout the house, and my 4s won't allow me out of the room. Is my new phone defective or just inferior.

4S at my house have stronger antenna than 3G iPhone. Reset Network Settings, tap Settings App>General>Reset, near bottom>Reset Network Settings. If still problem take to Apple for Warranty Coverage.

How can I use the "Copy and paste" tool in order get stamps in the same position in different pages (Acrobat XI for PC)?

With Acrobat 6.0 I was able to copy a stamp in the same position (I mean "exactly" the same one) of different pages just by using the "copy/past" tool.
Now I am using Acrobat XI and it seems like it is not possible anymore: I am copying a stamp and I am trying to past it in anoter page, but it appears in the center of the page (or wherever it wants to...).
Does anyone have a solution?
Thanks in advance.

Thank you very much. I'll be waiting for you message.
Messaggio originale----
Da: [email protected]
Data: 26/01/2015 17.56
A: "Umberto Gangi"<[email protected]>
Ogg: How can I use the "Copy and paste" tool in order get stamps in the same position in different pages (Acrobat XI for PC)?
    How can I use the "Copy and paste" tool in order get stamps in the same position in different pages (Acrobat XI for PC)?
    created by Gilad D (try67) in Creating, Editing & Exporting PDFs - View the full discussion
Well, I was in the same situation so I've developed a tool that allows one to do it. I will send you some additional information about it in a private message.
     If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7132586#7132586 and clicking ‘Correct’ below the answer
     Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7132586#7132586
     To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following"
     Start a new discussion in Creating, Editing & Exporting PDFs by email or at Adobe Community
For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624.

HT4314 I have a iPad and iPhone with the same Apple ID, but on Game Center I have used the same id for both devices and they are two different profiles and I was wondering how to have one of the accounts on both devices.

I have a iPad and iPhone with the same Apple ID, but on Game Center I have used the same id for both devices and they are two different profiles and I was wondering how to have one of the accounts on both devices.

Hi Jamesdwills,
Welcome to the Support Communities!
If you are using the same Apple ID on both devices, the Game Center profile should be the same.
Check out this information from the iPad User Guide. Try signing out of the Game Center on both devices and then sign back in with the correct Apple ID:
Using Game Center
http://support.apple.com/kb/ht4314
Game Center settings - iPad User Guide
http://help.apple.com/ipad/7/#/iPad9a13d039
Game Center settings
Go to Settings > Game Center, where you can:
Sign out (tap your Apple ID)
Allow invites
Let nearby players find you
Edit your Game Center profile (tap your nickname)
Get friend recommendations from Contacts or Facebook
Specify which notifications you want for Game Center. Go to Settings > Notifications > Game Center. If Game Center doesn’t appear, turn on Notifications.
Change restrictions for Game Center. Go to Settings > General > Restrictions.
Cheers,
- Judy

Blackberry 9320 broken,9360 on the same route due to "battery to low for radio use" etc

Similar Messages

Maybe you are looking for