Blank/black 3/4 inch ribbon around edge of monitor

Recieved HP 23 all in one last Wednesday and the sceen displays were occupying the entire monitor, Now the displays are reduced so that there is 3/4 inch of blank/black screen all the way around the monitor. Screen resolution is set to 1920X1080. Spoke w/MS and they do not think it is a Windows 8.1 issue.

Hello , I have read your post on how your desktop monitor produces a loss of signal, or the screen goes black, and I would be happy to help you! Since you mentioned that you have completed all of the steps in this docuemnt, and the issue continues, please contact our technical support for further assistance in this matter by clicking the link below to get the support number for your region.
www.hp.com/contacthp/
I hope this helps!
Regards

Similar Messages

UltraSharp 2407FPW 24.0-inch Wide Flat Panel LCD Monitor Supports HDCP,

The Dell UltraSharp 2407FPW 24.0-inch Wide Flat Panel LCD Monitor Supports HDCP. I am going to order a Mac Pro and it has an Ati Radeon X1900 XT which is HDCP ready. But I really want an Apple Cinema 30 inch Display. Does anyone know how long it is going to take Apple to release the new displays with HDCP? And does anyone recommend the Dell Monitor> Is it better than the Apple Cinema Displays? Thank You.

looking at both up close I think the 3007WFP looks nicer than the apple 30 inch, it also supports HDCP.

RE: 2211x monitor. Removed clear film around edge but does the long sticker at the top come off?

RE: 2211x monitor. I have removed the clear film around edge of the black monitor but does the long sticker advertising features at the top come off? I don't want to try and realizes it is well and truly glued on.
This question was solved.
View Solution.

It should come off, and if you are scared you can use goof off if it leaves pieces behind, or just rub your thumb or finger over it until it becomes hot then pieces should come off.
Please give Kudos. What other kind of recognition could I get?
Have I solved your problem? Mark solution as accepted.
I try to hate Macintosh. I really do. But I can't bring myself to hate any electronic device.

Which Graphics Card for a 40 inch HDTV LCD or Plasma Monitor for the best

Which Graphics Card for a 40 inch HDTV LCD or Plasma Monitor for the best value and price?
Hi, I was wondering if I replace my current standard graphics card for a MacPro Early 2008 for a graphics card for a 40" HDTV, which was is the best for the price and value? My current card when used with such a large monitor/ TV isn't very good, I think? So thinking of updating...

This sounds like a price match question. Without knowing all the details, it sounds like a yes for the Westinghouse, but I would encourage you to read the price match policy link here:
http://www.bestbuy.com/site/Help-Topics/Bestbuy.com-Price-Match-Guarantee/pcmcat204400050011.c?id=pc...
If all you care about is 1080p definition and an HDMI input at a $300 price point then this tv should suit your needs. (As a bonus it has 120Hz refresh for smoother action scenes.)http://www.bestbuy.com/site/Westinghouse+-+40%26%2334%3B+Class+-+LCD+-+1080p+-+120Hz+-+HDTV/5772998....
Although I do work for the Best Buy, all comments and opinions are my own.

Pixel around edge on Chroma key

I have trouble to remove green edge around me. I add spill suprresor green. but it show gray on edge. i have to use soften edge that cause gray on edge.
I don't understand why bad pixels around edge. That cause me struggle to remove gray edge.
Why pixels?
I use DV on HDV camera but DV setting.
I use chroma keyer, color smoothing-4.1.1, spill supressor-green, FCP 7
I thought I have plenty light but apparently not. 5 lights. 2 dome on green, 2 key lights on me, one back light.
Thanks

yep your far too close
you must have a good separation between the subject and the background
as a rough guide in setting up; the subjects shadow coming from the main light should not be able to fall on the background, if it is, move the subject further away.
The chroma keyer in FCP is very basic and needs a very good lighting set up to make it function
good level of illumination, even flat lighting on the back ground, good 3 point lighting on the subject to separate from the background.

Macbook does not shut down or restart. It stops at an blank white screen with the cursor moving around it. Updated to the latest software

I have a Macbook Air 13.3" 2012 model. For a couple of days my Macbook does not shuts down. It just stops at a blank white screen with the cursor still hovering around it. I have to shut it down forcefully every time using the power button.

These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
For this step, the title of the Console window should be All Messages. If it isn't, select
          SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar at the top of the screen.
In the top right corner of the Console window, there's a search box labeled Filter. Initially the words "String Matching" are shown in that box. Enter "BOOT_TIME" (without the quotes.)
Each message in the log begins with the date and time when it was entered. Note the timestamps of the BOOT_TIME log messages, which refer to the times when the system was started. Now clear the search box and scroll back in the log to the last boot time when you had the problem. Select the messages logged before the boot, during the time something abnormal was happening. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
For example, if the system was unresponsive or was failing to shut down for three minutes before you forced a restart, post the messages timestamped within three minutes before the boot time, not after. Please include the BOOT_TIME message at the end of the log extract—not at the beginning.
If there are long runs of repeated messages, please post only one example of each. Don’t post many repetitions of the same message.
☞ When posting a log extract, be selective. A few dozen lines are almost always more than enough.
☞ Some private information, such as your name, may appear in the log. Anonymize before posting.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Step 2
In the Console window, select
          DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar.
There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A crash report has a name that begins with the name of the crashed process and ends in ".crash". A panic report has a name that begins with "Kernel" and ends in ".panic". A shutdown stall report has a name that ends in ".shutdownstall". Select the most recent of each, if any. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot. It's possible that none of these reports exists.
I know the report is long, maybe several hundred lines. Please post all of it anyway.
☞ If you don't see any reports listed, but you know there was a crash or panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
☞ Please don’t post other kinds of diagnostic report—they're very long and rarely helpful.

Laptop Blank/Blackscreen Issue

Hello guys.
I have a HP laptop Envy 17 3D. Yesterday As I was using it just browsing the internet, I went to shower when I came back to it about 15 mins later the screen was black you could see the white led but nothing on the screen. I turned it off assuming it jad just frozen when I turned it back on the screen just doesn't show anything not even a light. The led for wifi on the keyboard lights up and the harddrive led is flashing. The motion sensor the laptop has seems to work as the keyboard . lights up when I approach it. I already tried using an HDMI to connect to a tv screem. The TV detects that there is an hdmi plugged to something but nothing displays. I've also tried switching the RAM from different slots. I have no idea how anything could have happened to it while I was showering.
Note: I am NOT able to access anything on the screen including the BIOS.

Hi @jorgecar ,
Thank you for visiting the HP Support Forums and Welcome. I have read your thread on your HP ENVY 17-2090nr
3D Notebook and getting a blank or black screen on startup. Try performing a hard reset. When performing a hard reset please note remove any and all USB devices. Disconnect all non-essential devices.
Here is a document on computer will not start.
Hope this is helpful.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Macbook Pro 15 Inch, broken screen to external monitor

I have a 15 inch macbook pro that was stepped on and the screen was broken. I took it to genius and they said it was toast. Great help guys. I took it home and plugged it in from the mini display to HDMI and my desktop appeared on the television screen. Simple as that. Keep in mind this is a 42 inch panasonic TV. But when I plugged it into my vizio television that is in my personal room the desktop was to the left, (regularly you have to drag whatever you want to the right. It's a double screen) and what was appearing on the TV was just a blank desktop which is no help at all.
I need to see my desktop on my vizio television.
So i was reading about the mirror image option under >display >system preferences and I turned that on when I was doing work on the panasonic and now I can't access anything, from either television.
So I need to either
A. find a way to reset system preferences on my Macbook Pro 15 inch with no access to the desktop so I can get it working on at least the Panasonic television again.
Or
B. Find a way to get in up on the Vizio. (prefered.)
Any suggestions.
Thanks so much.

Its a keyboard shortcut to mirror or un mirror screen. Then you can use your mouse and what not. My macbook air fell about 1.5 feet to carpet and thanks to the thin design of the metal parts turned the dam n screen into a knife and sliced the wires for the screen, wifi, Bluetooth, and camera... Well one wire was still attached, the one that powered the screen. So all i had was a white screen. I know its accidental damage and all but to have it fall and break a week after my warranty ran out ***?!?! Apple must employ ninjas!

How can I print with black border around edge of image?

I'd like to add a black border around the edge of certain images I'm printing. I know it's fairly trivial in Lightroom, but I can't see where this option is in Aperture. Is this lacking in Aperture, or am I just missing it? Many thanks.
PS -- I'm aware there are some plug-ins that claim to do this, so if Aperture can't do this, please feel free to chime in with comments on the best plug-in for this task.

Rich Hayhurst wrote:
Here's what you need:
http://www.apple.com/downloads/macosx/aperture/apertureborderfx.html
Aperture BorderFX 1.1
Thanks, Rich. That's a good plug-in, and does cover what I need (with lots of other features, too). The problem, though, is it requires an export of the image, which I then have to either print from another application, or reimport to Aperture to print. I was hoping to find something that will either just apply the border to the print job, or that would serve as more of an Edit With . . . type of plug-in than an Export plug-in, so I can keep everything in one place. Thanks again.
Message was edited by: jeffd55

I have a white round spot about one inch in diameter on my monitor; how can i get rid of it?

I have a white spot, about one inch in diameter, on my iMac monitor. It does not go away even after I restart the computer. What is the cause and how do I get rid of it?

It has now disappered after I had shut down the computer. It was opaque and oval. All applications so it must have been a monitor problem. Thanks.

24 inch iMac with a second monitor (1920x1080)

I just purchased an HP w2338h and have it hooked up to my 24 inch iMac as a second display. I am using a VGA cable with the apple adapter. The problem is, it won't support the native resolution (1920x1080). Every resolution below this works fine but I obviously don't want to use a lower resolution. I have the option to choose 1920x1080 but when I do, it leaves a two inch black gap on the left side of the screen and puts strange bands down the part that does show up. Any help would be appreciated. Thanks.

In another topic thread,
http://discussions.apple.com/message.jspa?messageID=9184329
+JustCallMe Dude+ posted that this product worked well
http://www.amazon.com/PTC-Premium-Mini-DVI-adapter-6ft/dp/B001H0REVK
Seems to be the right adapter and cable for you as well.

Can't get rid of gap around edge

Hi there,
I'm struggling to get rid of the gap around the edge of the website I've just started building. I've got the margins set to 0 for the top, and the divs are 100% width. Does anybody have any ideas? I've attached a picture to demonstrate and also please see the code pasted in below, in case that's useful.
Thanks,
Mark
Code:
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=utf-8" />
<title>Untitled Document</title>
<style type="text/css">

</style>
</head>
<body>

<div id="header">
<div id="container_header"></div>
</div>

<div id="navbar">
<div id="container_navbar">SPRY MENU GOES HERE</div>
</div>

<div id="main_text">
<div id="container_maintext">MAIN CONTENT GOES HERE</div></div>
</div>

<div id="footer">
<div id="container_footer">FOOTER CONTENT GOES HERE</div>
</div>
</body>
</html>

Add the below to your css styles:
body {
margin: 0;
padding: 0;

White border around edge of pdf (not picture related)

I've been fumbling with this for days and can't figure it out. I guess that means it's probably something really simple.
I'm using CS5 and am trying to create a book cover for self-publishing.
The artboard is set to 17.28" wide and 11" tall with .125 bleed.
I created a blue rectangle (no stroke) as a background to cover the artboard and the bleed so it measures at 17.53" wide (17.28"+.25") and 11.25" tall.
Theoritically that should work? However, when I save as a pdf (or print to pdf), the document size is 17.53" wide and 11.25" tall, but there is a white gap around the top/bottom/right edge.
I've tried:
- making the rectangle larger than the bleed section
- making the artboard a little larger
- no stroke/with stroke around the rectangle (thinking it had something to do with what others have been experiencing with white lines)
- making sure smooth line art is selected
- a host of other things
.. but no change.
Image is attached, but may need to zoom in to see problem.
Any help is greatly appreciated.
Thanks.

Hi Jacob,
Thanks for the response.
I tried your suggestions - no change.
It's a simple file with not a lot of complicated items, basically just three rectangles to which I was going to add text later for the titles, etc.
The width of the artboard takes into account the size of the spine, which is calculated for each book since they have different number of pages.
I've uploaded the file if you want to take a look at it as it doesn't make much sense to me. The file can be downloaded from here:
http://www.ezref.com/wp-content/uploads/Book%20Cover%20-%208.5%20x11.ai
Thanks for your time and help.

Drop Shadow Around Edge of Website

I am trying to make a drop shadow all around the edge of a site in Dreamweaver CS4. I know I need to make a container around the wrapper and place it as a background image and repeat y. I know how to make the graphic in PS. What I can't figure out is how to make it look like it flows into the body background color. If the body has a sold background color it's not a problem, but what if the body backround is a gradient? If there is a gradient it doesn't look correct because I can't pic a color for my layer under the shadow in photoshop.
Also how do I get the background to show at the very bottom of the page.
Please help I have been trying to figure this out for hours

Also how do I get the background to show at the very bottom of the page.
If you are talking about a gradient, there are two ways to give that appearance.
1. Make the gradeint image longer that the page, for example create the gradient a size like 5px x 2500px. You will run into issues on differnet height pages.
or
2. And I thin a better suggestion. Create your gradient, then have it blend into the the background color. So for example if your gradient goes from black to light gray, make the background color the last light gray of your image...then it blends. On extra long pages you lose the gradient.
Gary

Fading around edge of images [cs3]

I've spent a fair bit of time a few times, using the eraser tool and soft brush to `fade' around the edges of photos so they don't appear hard but blend with the background in some smooth way near the edges.
I'm pretty sure this could be done using some kind of masking. I don't understand much about masking but wondered if someone might walk me through it, at least in broad outline.
I'm hoping I could create some kind of mask that could be used over any image of the right size. So that, if I had a bunch of same sized images I could make one mask and then tranfer the layer to all the pictures.
I'd like the end result to look something like the quicky sloppy job <ahref="www.jtan.com/~reader/vu/disp.cgi"> <b>HERE</b> </a>
where the top picture is unedited and I've used the big soft eraser around the edges of the bottom picture.
[ NOTE:
I can't seem to master the new controls on this forum so not sure how to enter a url and make it clickable... one failed attempt above.
Here is the site to copy and paste: www.jtan.com/~reader/vu/disp.cgi
Once more usging the insert tool:

if you are going to save your same sized picture in different names, like pic1, pic2 and so on:
drag all your pic to your main PSD
in the layer pallate, select them all
create folder for them
ctrl+click on one of the layers
you get the selection
select the folder
hit the create mask, now all your PICs are masked
select the mask and unlick the link sign
ctrl+T to control the size of the mask
feather it or blur it
thats it , you got one mask for all layers. you can delete, add and do anaything with one mask.
the idea of the mask is:
black and white, imagine you are in a dark room. you do not see any thing, since you turn on your tourch you see the ojects that stay under the spot light.
cheers

Blank/blac​k 3/4 inch ribbon around edge of monitor

Similar Messages

Maybe you are looking for

Blank/black 3/4 inch ribbon around edge of monitor