Blank page between printed page

Does anyone know why a blank page comes out between my printed pages? i AM USING vISTA WITH A HP Photosmart C7250 all-in-one
Diane

Check this page out:
Blank sheets
007OHMSS
I was a support engineer for HP.
If the advice resolved the situation, please mark it as a solution. Thank you.

Similar Messages

Reader XI, placing blank page between document pages?

I have Adobe Reader XI, Version 11.0.2. In the last two weeks one our agents readers started placing a blank page between document pages. We have re-installed the product a couple time, reset standard defaults, and it is stil placing blank pages between document pages. Any ideas to rectify the problems. Every document he pulls up this happens.

Can you give us a link to a document with these pages?
Reader cannot insert pages into a PDF file so something must be up with the PDF's themselves.

Can I add a new chapter page between existing pages?

I would like to divide the last chapter I've written into two chapters. I didn't think of this at the time, now it seems logical. I have added a new chapter page with photo template, it appears at the bottom of the "book navigation" pane, but I can't drag and drop it between the pages it needs to separate. Do I need to erase 8 pages and begin again? I hope not!

If you're used to fluid, non-linear editing, iBA can be quite the headache until you get in sync with how it expects us to work .
You may find it beneficial to experiment with throw-away books first, so that you find out what will/won't work for your content - that way you may reduce time wasted learning the hard way later. I find it's better to spend time rough drafting my content on paper, or in Pages, before laying it out via iBA. Once you get into the habit of linear editing, you'll have an easier time of it - I hope.
Good luck in any case.
Ken

Insert PDF page between PDF pages

I've asked this over on the acrobat forum but no response so I'm trying my luck here.
I've got a 500 page pdf that's 4 up.
And I"ve got a 1 page pdf 4 up that's the reverse for the 500 pages.
I'd like to insert the 1 page pdf in between each of the pages in the 500 page pdf, effectively giving me a 1000 page pdf.
I've tried Multipage importer along with another script to insert a master page between pages but honestly - it takes far too long to process a 500 page multipage import then insert a b master with the page and export back to PDF, taking well over 45 minutes.
Especially when I tried job no.2 with a 1500 page pdf where a pdf needs to be inserted between each of those pages.
Plus it ties up the entire computer.
Does anyone know of a way to insert 1 page pdf in between a multipage pdf?

the script can be found here: Re: How can I merge even and odd pages of a PDF? (8th post down posted by jbaitis) - copy and paste the script into a text editor and call it "collate.js" (without the quote marks of course)
to install it, close acrobat, and then copy the script into this location (assuming you work on a mac using Acrobat XI)
/Applications/Adobe Acrobat XI Pro/Adobe Acrobat Pro.app/Contents/Resources/JavaScripts/collate.js
restart acrobat and when a file is open, there should be two new options available under "undo" in the edit menu: collate and reverse. collate works by getting file A and interleaving it with file B, so both files need to be the same page length. In Eugene's case, this would have meant creating a common back file that was as many pages as the front, but that isn't too hard to do via the finder and the "combine files into a single PDF" function in Acrobat.
That said, my earlier "bonkers" approach using the split feature worked too, but the collate script is far, far easier.
Colin

Blank spot in printed page - CP1518ni

My CP1518ni has always worked well, except for one new problem. About one page in five includes a small (c. 1" long, 1/4" wide) blank space on the left side. And a small amount of nearby type is slightly smudged. The appearance is as though a single piece of shredded paper covered that part of the page. But I've searched thoroughly and found nothing in the printer. Is there anything to be done?

Hello, I see that you are getting a blank space on the left side of the page. I will certainly do my best to help you. Make sure the printer is connected directly to a wall outlet. (don't use a power hub or a surge protector) This ensures the printer is receiving full power and may help this situation. Inspect the toner cartridge for damage:
1. Remove the toner cartridge from the product and verify that the sealing tape has been removed.
2. Check the memory chip for damage.
3. Examine the surface of the imaging drum on the bottom of the toner cartridge.
CAUTION: Do not touch the roller (imaging drum) on the bottom of the cartridge. Fingerprints on the imaging drum can cause print-quality problems.
4. If you see any scratches, fingerprints, toner or other damage on the imaging drum, replace the toner.
5. If the imaging drum does not appear to be damaged, rock the toner cartridge gently several times and reinstall it. Print a few pages to see if the problem has resolved. You can calibrate and run a cleaning right from the printer's control panel. Calibrate the printer.
On the printer select the OK button/arrow to main menu system setup/print quality/calibrate color/calibrate now.
Run a cleaning.
On the printer select the OK button/service/cleaning mode/OK.
Print a Diags page.
On the printer select the OK button/main menu report/diagnostics page.
Check the alignment. Please try the steps in this document if you are still having issue. Resolving Print Quality Issues. Are you using Genuine HP Toner?
What are the toner levels?Let me know the results of the Diagnostics page. If you appreciate my efforts, please click the 'Thumbs up' button below.If there is anything else I can help you with, just let me know. Thank You.

Blank flash between SWF pages

Hi all!
I am building my first Flash website and have a small
problem.
I am building it using individual SWF files for each page.
However, when I click a button to navigate from one page to
another, I am getting a flashing blank screen for just a split
second. What i mean is, it doesn't quite flow from one page into
another - just for a split second, a blank screen appears.
Anyone got any idea why this is and how to get rid of it???
THANKS ALL!
Liam

"liamfahy" <[email protected]> wrote in
message news:e80fg1$7tg$[email protected]..
> Hi all!
>
> I am building my first Flash website and have a small
problem.
>
> I am building it using individual SWF files for each
page. However, when I
> click a button to navigate from one page to another, I
am getting a flashing
> blank screen for just a split second. What i mean is, it
doesn't quite flow
> from one page into another - just for a split second, a
blank screen appears.
>
> Anyone got any idea why this is and how to get rid of
it???
>
> THANKS ALL!
>
> Liam
Instead of replacing your current object with a completely
new one, load it into a movieclip or a level instead
tralfaz

Reducing blank area around printed pages doc....

After printing a pages document, based on the 'Flyer' template, the white border around the document is massive. In fact the actual printed area matches very closely the size of an A5 page. I have checked the page size, and unless there is a setting for it I have missed, it is A4 sized. In fact, I can show Pages' rulers to confirm it thinks the page is 21.0 x 29.7cm.
Retrying with a new tempplate, before editing it, prints as I would expect, right up to the very edges of the paper.
I have been through all the Instector pages and I can't see anything I recognise as the fault, that doesn't necessarily mean that it definitely isn't there somewhere though. I think I may have messed around with the little blue arrows in the rulers at one stage but finding them again doesn't answer it.
The only clue I have is it displays the page, when I'm editing it, with a large grey space to the left of the document, which looks about the same size as the missing page area. This document concerns the sale of a very expensive piece of property so it is quite important to me.
I enclose this picture hoping it will make answering the question easier...

Perfect answer!
That's fixed it... thanks Peter!

D7460 Printing empty page between each page

I've tried just about everything...test pages, Word & Excel docs and I have been through and changed almost every parameter in printer preferences and properties GUIs....?

Hi,
I'm sure I'm pointing to the obvious answer, but have you checked that there is no page break before of after both blocks. Probably you have one more than you need.
If you have defined one block in one logical page you do not need page breaks.
I hope this helps you.
Elisa

Why does my HP LaserJet 4 Plus put out blank page after print page?

why does my laser Jet 4 Plus put out a blank sheet after every print page

This sounds like an issue that could result from having A4 sized paper but having the printer settings set for A size. Please check the paper settings.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Is it possible to INSERT a blank page Between existing pages? Everytime I try it inserts the page at the END of the document.

Everytime I try it inserts the page at the END of the document. The HELP is no help, and I can't find any other documentation on being able to do this. Appreciate the feedback. Thanks! - ph

AP,
As Fruhulda notes, a Section Break is an Inline character that will move all text below it to the next page. With a combination of graphics and text, and with the graphics having the property of Object Causes Wrap turned on, you will get these apparently odd behaviors. This is why I often favor the Page Layout mode myself. As many experienced users will say, you can do anything in a WP doc that you can do in a PL doc, but in my opinion the WP features often get in the way of simple operation when graphics are involved.
Glad you are on track now.
Jerry

Printer printing blank sheets between printed ones

I have a HP Officejet 6210 all in one, running windows XP. My problem is when I am printing something I made up in microsoft word, it puts out a blank sheet first than it puts out a blank sheet in between the printed ones. I don't want to have to babysit it if I have a lot of copies to print.It seems to only do it on certain ones. I have an older version of word.

This article should help resolve your blank pages:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01892627&cc=us&dlc=en&lc=en
Give the steps listed under your operating system a try and let us know if it helps.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

1 horizontal page between vertical pages

I'd like to add one horizontal page in a document with vertical pages. I can only change all to vertical or horizontal but how can I achieve what I want? Or is it iWork that can't do this? (Microsoft Office is able to do this )

Pages has the same size and orientation to its pages, throughout a document, which is generally a good idea, I'm not a great fan of the way Word does it.
Pages does let you rotate the contents of a page and unrotate it for you to edit it. this may meet your needs.
More expensive DTP apps let you have "spreads" which span several pages (as in a fold out section). Maybe some day Pages might do this.

Alternating Printed Page then Blank Page, Deskjet 950C

MY Deskjet 950C suddenly decided to start alternating printed pages with blank pages, when printing any amount of pages or copies (blank comes second).
Operating this on Vista, connected via USB using the Vista driver (since HP doesn't offer Vista driver for older printer), the one that gives printer name as "Deskjet 950C/952C/959C".
I'm using Letter size paper, have tried all Paper Source settings (Auto, Upper Tray, Manual) and have set Scale To Paper Size to both Letter and No Scaling. Have tried Print Page: 1 and Print Current Page, still prints a blank after the printed page.
I use this as a 'workhorse" printer for bulk jobs. My HP C7250 All-In-One is working perfectly normal.
I've run out of ideas, and it's a pain to keep taking out those blanks.
Any ideas anyone?

Ok, strangely enough it stopped.
I went in to Media (paper Type) and changed it to HP Brightwhite Inkjet paper, then changed it back to Plain Paper, and it's not doing it anymore.
Strange. Very Strange.

How to avoid TEST PRINT page

Dear All,
How to aviod the test print page in printing. I am getting SAP cover page(test print page) for every time I am printing. I ma using the following code.
CASE sy-ucomm.
    WHEN 'PRNT'.
      DATA: l_params TYPE pri_params,
            l_valid TYPE c,
            l_arc_params TYPE arc_params.
          l_params-prsap = 'X'.
      CALL FUNCTION 'GET_PRINT_PARAMETERS'
        EXPORTING
          destination            = 'LPIN'
          copies                 = 1
         list_name              = 'TEST'
         list_text              = 'Test NEW-PAGE PRINT ON'
          immediately            = 'X'
          layout                 = 'X_65_132'
          line_count             = 65
          line_size              = 220
          release                = 'X'
          mode                   = 'CURRENT'
          no_dialog              = 'X'
        IMPORTING
          out_parameters         = l_params
          valid                  = l_valid
        EXCEPTIONS
          archive_info_not_found = 1
          invalid_print_params   = 2
          invalid_archive_params = 3
          OTHERS                 = 4.
      NEW-PAGE PRINT ON   PARAMETERS l_params NO DIALOG.
      PERFORM display_data.
      NEW-PAGE PRINT OFF.
ENDCASE.
Thanks,
Ranjan

Hi,
Just check it out. I m printed report directly instead of display.
w_destination = 'LOCL'.
    CALL FUNCTION 'GET_PRINT_PARAMETERS'
      EXPORTING
        destination    = w_destination
        layout         = 'X_58_170'
        no_dialog      = 'X'
      IMPORTING
        out_parameters = params
        valid          = valid.
    IF valid <> space.
ALL DISPLAY PARAMETER RIGHT ON PRINTER
      NEW-PAGE PRINT ON PARAMETERS params NO DIALOG.
    ELSE.
GIVE ERROR PRINTER DESTINATION IS NOT VALID
      MESSAGE s208(00) WITH text-010.
    ENDIF.
ENDIF.
User write stament, That will dirctly go for print.
OFF THE PRINTING AFTER REPORT IS DISPLAY
IF valid <> space.
    NEW-PAGE PRINT OFF.
ENDIF.
it may sortout ur problem.
Regard,
Vinod

LASERJET 1160 PRINTER RUNS A BLANK PAGE BETWEEN EVERY PRINTED PAGE AFTER UPGRADING TO WINDOWS 8.1

Laserjet 1160 printer runs a blank page between every printed page after upgrading to Windows 8.1

I am sorry, but to get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial printer. You can do this at Printers - LaserJet.
Click on New Post.
I hope this helps.
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Blank page between printed page

Similar Messages

Maybe you are looking for