Blank screen after i reset help please

my screen is white blank i tried resetting and restoring numerous times also plugged it in to computer wont recongnize device please helpit is the iod nano

Hi RexGenius,
I understand that you are cannot boot up your HP ENVY Sleekbook 4-1117nr. I will try my best to help you resolve this issue.
In this document for Troubleshooting Black Screen Displays with No Error Messages During Startup or Boot that may resolve this issue.
Since you were in the system recovery when the issue started, I am also sending this document for Troubleshooting HP System Recovery Problems (Windows 8).
I hope this information helps, please let me know.
Thank you,
I worked on behalf of HP.

Similar Messages

  • Blank Screen after factory reset 7911 phone

    Hello guys,
    I had a weird issue on an 7911 ip phone. It was connected to my network and on the display of the phone was saying "ethernet disconnected".
    What i did was a soft and a hard reset using 123456789*0# and then 3497672850*# following the guidelines of a conversation in the forum
    https://supportforums.cisco.com/thread/2166581
    After the factory reset the device has a blank screen (I left it for more than an hour connected on the network bearing in mind that some processes might be loading in the background and the firmware will load at some point..that didn't happen) and it is unable to receive an ip address ("show ip dhcp bindings", shows nothing related to the mac address of that device).
    To eliminate the possibility that the problem might be on the network card of the phone, i've factory reset a working phone using the above described procedure.
    I had the same problem with that phone too.
    Are there are any log commands that i can use to further investigate my issue?  (I can't see any logs using "terminal monitor"command)
    I am using call manager express 4.3.0 on a cisco 2800 router.

    Dragan,
    I tried what you suggested with no luck.
    What i noted is that, when i plug the power adapter on the phone and connect the ethernet cable on the switch port of the phone (the other end goes to a d-link small switch) the light on the small d-link switch doesn't come up. However if i plug the ethernet cable on the pc port of the phone the light goes green. I checked it with two phones that i've factory reset and it is the same problem.
    What i understood from this, is that the pc is unable to retrieve an ip from the dhcp server and the necessary option 150 to locate the tftp server and retrieve the necessary firmware.
    Gordon, due to the above mentioned problem i can't proceed with wireshark since i don't have network connectivity between the phone and my workstation.
    Guys, do you have any alternatives that i can give a try?
    Thanks a banch!

  • X79A-GD45(8D) Blank screen after CMOS reset

    I had a bad switch and a bad GPU that came on my Black Pearl
    from Cyberpower. They sent replacements and I thought I would
    add a hard drive I had and a sound card. I was adding the
    sound card because after I got replacement the GPU the sound was bad.
    I must have hit the on board system with the card.......
    I put the hard drive and switch in and tested the system.
    It worked fine but the spalsh screen didn't come up.
    I was going to disable the onboard sound in BIOS but the Boot screen
    nor BIOS would come up. If I hit DEL or f11 I got a blank screen.If I
    did nothing it went straight to the Windows screen with the users on it.
    I checked on the forum and found the thread about reseting the CMOS to
    fix that problem. I shorted the jumper as the manual said, removed the
    battery and hit the reset switch. The system came up, sounded like it
    was hitting the floppy then the blue LEDs went out and it came up again.
    It would keep coming up and shutting down until I pulled the plug.
    Is it looking for a boot disk? I have a repair disk from CyberPower
    I tried in both drives while it was cycling with nothing happening.
    Any suggestions?
    CPU: Intel(R) Core™ i7-3820 Quad-Core 3.60 GHz 10MB Intel Smart Cache LGA2011 (All Venom OC Certified)
    FAN: Asetek 510LC Liquid Cooling System 120MM Radiator & Fan
    HDD: 240 GB Intel 335 Series SATA-III 6.0Gb/s - 500MB/s Read & 450MB/s Write (Single Drive)
    LG 14X BLU-Ray Rewriter
    MEMORY: 16GB (4GBx4) DDR3/1600MHz Quad Channel Memory
    MOTHERBOARD: (SLI/CrossFireX Support) MSI X79A-GD45(8D) Intel X79 Chipset Quad Channel DDR3 ATX Mainboard
       w/ Winki 3, OC Genie II, 7.1 HD Audio, GbLAN, 3 Gen3 PCIe X16 & 4 PCIe X1
    OS: Microsoft(R) Windows 7 Home Premium [+0] (64-bit Edition)
    OVERCLOCK: Extreme OC (Extreme Overclock 20% or more)
    POWERSUPPLY: 1,000 Watts - Cooler Master Silent Pro Gold 80 Plus Power Supply ( 80 Plus Gold)
    SOUND: HIGH DEFINITION ON-BOARD 7.1 AUDIO
    VIDEO:  Two AMD Radeon HD 7970 3GB 16X PCIe 3.0 Video Card (MSI)

    Since the board is part of a Cyberpower PC you have to ask Cyberpower about that issue as they cover support for that machine.

  • 3rd gen iPod touch. I just get a blank screen (after a few secs of the apple symbol) when it is switched on or when connected for charging. I know the connections are OK. Suggestions/help please

    3rd gen iPod touch. I just get a blank screen (after a few secs of the apple symbol) when it is switched on or when connected for charging. I know the connections are OK. Suggestions/help please

    I took the iPod to the local Apple shop. The guy put the iPod onto a docking station and checked it - answer "connections are OK". I have used the link before but have not gone through all its suggestions (although picked on the most relevant ones). I may have to go back. Thanks again for your suggestions

  • After upgrading to the newest version of firefox my Juniper J-web web-gui showing a blank screen after login.

    Hi.
    After the newest version of firefox the browser only show a blank screen after doing the login on all Juniper SRX devices.
    Some one who can help me here?
    Kind regards
    Jonas (Denmark)

    Jonas,
    Please see:
    *[https://support.mozilla.org/kb/Server+not+found]
    *[https://support.mozilla.org/kb/Firewalls]
    *[http://kb.mozillazine.org/Error_loading_websites]
    *[http://kb.mozillazine.org/Browser_will_not_start_up]
    It could be that you need to reset Firefox to its defaults, however there could also could be something going wrong with the login request. Please check the Firewalls and loading websites to see if anything is blocking a request.

  • Laptop only coming up with a blank screen after set-up?

    Ok, so. My parents bought me a brand new hp laptop for christmas. On christmas day i went through the whole set-up process and did all the steps it told me to do. When i'd been through all the steps, i got a loading symbol and ever since, all it comes up with is a blank, black screen and a mouse icon that i can move. I'm not 100% sure of the model though (appologies). What do i need to do??
    Cheers

    Hello @15_,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I have read your post on how your notebook is coming up with a blank screen after setting it up. Is the power on the computer on? Is there an error message on the screen? I would be happy to help you, but first I would encourage you to post your product number for your computer. Below is a is an HP Support document that will demonstrate how to find your computer's product number. In addition, it will also help if you indicate which operating system you are using; and whether your operating system is 32 or 64 bit. The more information you can provide, the better!
    How Do I Find My Model Number or Product Number?
    Which Windows operating system am I running?
    Is the Windows Version on My Computer 32-bit or 64-bit?
    Please re-post with the necessary information, this way I will be able to research this further for you. I look forward to your reply!
    Cheers!
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • Bootcamp goes blank screen after startup sign.

    I'm unable to start up my bootcamp. It just goes blank screen after the startup moving icon and stays blank screen. Can anyone help? Thank you in advance!!!

    @MT1 
    ‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
    If you are unfamiliar with the Forum's private messaging please click here to learn more.
    Thank you,
    Omar
    I Work for HP

  • Blank screen after setting back to Factory Default Setup

    After setting an HP Pavillion laptop with Windows XP back to the default factory setup, I get nothing but a blank screen after turning the laptop on.  The HP screen doesn't appear, there is just a blank screen.

    I have also gotten the blank, black screen, after using the Recovery CD's from HP on THREE different computers, please, if anyone knows how to help, HELP. I get nothing, tried hard off, new memory, new hard drives, no battery, battery, new battery, new a/c adapter, etc. Only one is still under warrenty, a HDX-16t, the other two, an HDX 16 and a Pavilion -1135nr

  • Blank screen after KitKat update

    I just completed the KitKat update on an Ellipsis 7 tablet that's connected to Verizon's network, but now I'm only getting a blank screen after the welcome screen displays. Fyi: the first part of this update went smoothly. Can anyone can help me resolve this issue? I really like this tablet and use it everyday.

    I contacted Verizon support and a couple of techs attempted to walk me through alternate boot methods. However, as bassclarinetl2 noted, "pressing the power button to turn the device off results in the device powering up by itself and both 'safe mode' and 'factory reset' are inaccessible via their button combinations." Therefore, I'm sending my tablet in to be repaired or replaced under warranty. Depending on how long you've had your Ellipsis 7 tablet, you may be able to do the same.
    Incidentally, I have another (seemingly) identical Ellipsis 7 tablet and was able to successfully install the KitKat upgrade on this second tablet, which I'm using now. The sooner Verizon determines why the upgrade worked on one tablet and not the other, the better.

  • BLANK SCREEN AFTER WINDOWS 7 LOGIN

    Hi, I am getting a blank screen after i login. -I have no available restore points-safe mode works fine-Explorer.exe works but some programs play up and i dont really want to do a clean install  Please help !

    Same problem  I've found a solution.
    #1 Hit fastly 5 time the left shitf button on your keyboard.
    A windows will appaers to know if you want to caps lock. Keep it open
    #2 Alt-CTRL-Del
      You have know your desktop
    #3 Go on add-remove programme
    3a) Go on windows add-remove
    3b) Remove internet explorer
    ok-ok-ok - untill it's remove and ask to restart
    #4 No more problem. You have to go on the net with chrome or firefox.

  • Blank Screen after 703HP3 (Linux)

    Hi,
    after update a VMWare-SLES10SP2-Server with DOM and Webaccess HP703HP1 to
    HP703HP3 I got a blank screen after starting the machine.
    All logs look got but I can't login in. Only a blank web page. No login. No
    picture. Nothing.
    Any idea?
    Have anybody the same problem?
    I went back to my snapshot. So my user can login.
    Now I will try it at another server.
    Andreas

    Hi Massimo,
    the login web page for webaccess for the user...
    Andreas
    "Massimo Rosen" <[email protected]> schrieb im Newsbeitrag
    news:[email protected]..
    > Hi,
    >
    > Andreas Schild wrote:
    >>
    >> Hi,
    >>
    >> after update a VMWare-SLES10SP2-Server with DOM and Webaccess HP703HP1 to
    >> HP703HP3 I got a blank screen after starting the machine.
    >
    > What do you mean "a blank screen"? A blank screen where?
    >
    >> All logs look got but I can't login in. Only a blank web page. No login.
    >> No
    >> picture. Nothing.
    >
    > I'm sorry, but it's totally unclear what you're talking about. What web
    > page?
    >
    > CU,
    > --
    > Massimo Rosen
    > Novell Product Support Forum Sysop
    > No emails please!
    > http://www.cfc-it.de

  • Blank screen after login in SAP CRM 2007

    hi,
    we are experienceing blank screen after we login to crm2007 web client.
    what we have done
    - implemented sap note 168941, 612670, 1045941, 1144511
    - assign PFCG role to business role
    is there any other step we missed?
    Thanks.

    Hi friend,
    Please, check if in your pfcg profile you have the objects:
    uiu_comp
    CRMCONFMOD
    with value *
    Regards,
    Lalas

  • Blank Screen after Hibernate

    Hi,
    On my DV6-3085 I sometimes power up by opening the lid and get a blank screen after a few seconds.
    The screen will say Starting Windows, flash and then go blank. At this point the finger print scanner is still working and responds but you cannot obliviously see anything.
    I fairly suspicious this happens after the laptop has not been used for a little while (overnight) after a lid close, so the Sleep light has stopped flashing and the laptop is in hibernate mode.
    My guess is it is something to do with switching graphics adapters. I've not yet decided if plugging the power in first does or does not make a difference or being on battery or AC when the lid was closed.
    I've got the latest drivers according to the HP driver update utility.
    Anyone with the same problem or have a solutions?
    Thanks,
    Dean.

    Hi,
    On my DV6-3085 I sometimes power up by opening the lid and get a blank screen after a few seconds.
    The screen will say Starting Windows, flash and then go blank. At this point the finger print scanner is still working and responds but you cannot obliviously see anything.
    I fairly suspicious this happens after the laptop has not been used for a little while (overnight) after a lid close, so the Sleep light has stopped flashing and the laptop is in hibernate mode.
    My guess is it is something to do with switching graphics adapters. I've not yet decided if plugging the power in first does or does not make a difference or being on battery or AC when the lid was closed.
    I've got the latest drivers according to the HP driver update utility.
    Anyone with the same problem or have a solutions?
    Thanks,
    Dean.

  • SAP BPC 10.0 Web Client Blank Screen after login

    Hi ALL,
    We are using SAP BPC 10.0 Web Client with Adobe Flash Player 13.0.0.214 with IE 9.0 on Windows 7.0.
    We face strange error where on only on certain PC, the BPC web client working.. On other getting Blank/Blank Screen after login (with "movie not loaded" on the adobe flash player).. Both PCs are having the same setting.
    Even one of PC which previously working, starting this week suddenly getting the same error.. I have created OSS message and got feedback with also share this problem on this forum.
    I have done several actions as mentioned on several SAP notes )1624267, 1664889, 1681147, 1694871, 1752971, 1798336, 1804221, 1806371, 1811218, 1820505, 1918631, 1968584), but still no luck..
    If you have the same issue, kindly share..
    Thanks and regards,
    Hery

    Yes .. Compatibility View also checked.. in several PCs, it is working well. both failed and working PCs have the same setting.
    Just found another weird: in one working PC, 2 different windows local-admin users login to the same PC for BPC-web and getting different result (1 Ok ; 1 failed) ..seems it is related with the user profile and login-domain servers (we have multiple login-domain servers with load balancing mechanism).
    Thanks and regards,
    Hery

  • Mouse buttons no longer work for iTunes playback (play/pause, next, previous) after update! Help please!

    Mouse buttons no longer work for iTunes playback (play/pause, next, previous) after update! Help please!

    When you say "mouse button", do you mean clicking on the controls in the upper left of the iTunes window or do you mean that you have special media keys on your mouse?

Maybe you are looking for

  • Problem centering in a Panel

    In the following code, I can't figure out how to center the Button and Text components that have been added to a Panel. I can move things vertically by using a Spacer, but I can't figure out how to move them horrizontally. I want to center them in th

  • Updating Drivers

    Hello, I have a macbook air with windows 7 installed on boot camp. Recently, i have been having trouble connecting to some WIFI networks. Since i already had similar problems with a macbook, i think it is hardware related. I would like however to upd

  • How to create a collaboration room of the SAP Portal from EJB tier.

    Hi. I have created a EJB Stateless Session Beans, and I want to create a room using the API of KM. I have used the code mentioned in this URL: http://help.sap.com/saphelp_nw04s/helpdata/en/7d/c69c42d706c66ae10000000a155106/content.htm It works fine i

  • Microsoft ADO retrieval of output parameters

    I have the following C++ code:      int rc = 0;      CString QueryStr = "{ CALL PR_TROUBLE_CALLBACK_REQUESTS(?) } ";      CommandPtr          pCommand(_uuidof(Command));      _ParameterPtr     pParam;      _RecordsetPtr     pRecordset;      try{     

  • Automatic appending of file extension of downloaded files

    Hello, When downloading files with certain extensions (.doc, .xls, .ppt, .tar.bz2), Safari will append an extension to the file after the download is finished (.dot, .xla, .pot, .tar). I don't know what exactly is the case of the problem, but I know