Blank screen on HP pavillion tx 2500

Hi, i have a Hp pavillion tx 2500 which came pre-installed with a windows vista 64 bits. i upgraded it to windows 732bit. The finger print sensor and bottons like screen rotation werent working after i upgraded. The screen began to flicker about 2 months after i had itupgraded then i noticed if i held the right corner of the system tight, the flickering would stop. until recently, i would have to keep it on for a long while to heat up while the lights keep blinking and then switch it on and back on for the system to come up. However that method doesnt work anymore even if i leave the sys on for two days. i have tested the memory and slot.

Hello @MaggieKate,
I just sent you a private message. If you are not sure how to check your forum messages, this post has instructions.
I worked on behalf of HP.

Similar Messages

Blank screen on older Pavillion

I got this request from a family member:
"Anyhoo - I have an older HP Pavilion entertainment....something. It's currently packed away. But, I'm thinking that I might be able to fix one of my old computers to give to [family member]. That Pavilion worked for years but, suddenly, the screen went black. I've looked up a couple of "fixes" but I thought, as an HP person, you might know of some quicker fix? When I turn it on, the computer seems like it works - hums, lights up, etc. but there is no display at all. I looked into a couple of recommendations that said I could hit some of the F keys - got me nowhere. Any thoughts?"
My response:
"I don’t know right off any easy answers to what you’re describing. Will have to involve some troubleshooting to figure out what the problem is. Have you tried it with a different cable and monitor? Do you get a series of unusual beeps when you turn it on? If you’d like, I can throw your question out on HP’s forum and see if some of the PC experts can help. If you had the model number, I could probably get some more specific help from people who are true experts in that area. What is {family member} intending to do with the PC? Just Internet browsing or more comprehensive work / games?
Reply to my email:
"My old computer is an HP Pavilion dv9000, probably 6 years or so old. It was my only computer for years but suddenly, I tried to turn it on and got nothing other than the little operating noises I mentioned, but the screen just stays black. It doesn't make any weird noises unless I hit the F keys. Then it beeps with each key. The only other notable thing I can think of is that, when I turn it on, there is a glow all along the bottom of the screen. No matter what keys I hit, I get nothing on the monitor.
No, I don't have a separate monitor to test it. Can I check it with my current laptop? It's a Lenovo and I do have various cables. What do I do to test the HP?
If I can resurrect the computer, I want to give it to [family memeber]. It is a gaming machine but I only ran movies on it and then various office work. [family member] does nothing on computers so, all he needs is a very basic computer - just for email and capable of handling the very basic functions of a simple web page. I would like [family member]to be able to do email.
My request:
Can I get some help on troubleshooting this problem? if I was there, I'd try a different cable and monitor to determine if the problem is caused by one of those. Failing that, I'd replace the video card and see if that solves the problem. She doesn't have spare cables, monitors, or video card to test with. Any suggestions? Any information I've missed that would help identify where the problem is?
I am an HP employee.

Hi,
Unplug the battery charger and remove the battery. Now hold down the power button for one minute. Now replace the battery and plug the chanrger back in and give it a go.
Some of the HP DV9000 series laptops did experience this problem. I have been fortunate not to experience this issue with my DV9700 laptop.
HP DV2xxx to DV9xxx video issues. You can also get GPU repairs here.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

I have blank screen, after windows 8.1 upgrade on HP Pavillion 15-e005sv.

I have blank screen, only mouse pointer working after
windows 8.1 upgrade on HP Pavillion 15-e005sv.
Any help please.
This question was solved.
View Solution.

First of all you need to get into safemode
for that press f8 or del key while starting the computer
then you will get many options there you must go to safemode
Secondly ,after getting to safemode go to 1.control panel ->2.Device Manager->3.Disable AMD HD Graphics
Thats all
then restart your computer to get into normal mode
May be if you upgrade your amd hd driver your black screen problem will be gone

HP Pavillion 11 X360 Doesn't start, Blank Screen

Hello,
I am using HP Pavilion 11-n010en x360 PC and all of a sudden I started my pc and it never went ON. I opened the back cover, unplug the battery, hard power off, took off the ram and put back. Nothing is happening. There is just a white colored LED light by Power button and no charger issues. But there is no Screen. It is blank screen. Do not feel any movement in anything at all. Please suggest me Solution.
Regards,
oct4v3

Hello oct4v3,
I have read your post on how your notebook computer is not powering on, and I would be happy to guide you towards a resolution!
Since you have already reseated the memory and the battery for your computer, I recommend following this document on Computer Does Not Start (Windows 8). This should help to power on your notebook.
If the issue persists, please call our technical support at 1-800-474-6836. If you live outside the US/Canada Region please click the link below to get the support number for your region.
http://www.hp.com/cgi-bin/hpsupport/index.pl
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Blank screen after setting back to Factory Default Setup

After setting an HP Pavillion laptop with Windows XP back to the default factory setup, I get nothing but a blank screen after turning the laptop on. The HP screen doesn't appear, there is just a blank screen.

I have also gotten the blank, black screen, after using the Recovery CD's from HP on THREE different computers, please, if anyone knows how to help, HELP. I get nothing, tried hard off, new memory, new hard drives, no battery, battery, new battery, new a/c adapter, etc. Only one is still under warrenty, a HDX-16t, the other two, an HDX 16 and a Pavilion -1135nr

New Install - startx results in blank screen with mouse cursor

I installed Arch on my desktop last week with no issues, so I wanted to install it on an old THinkpad R31. Everything with the installation went smooth, but when I try to 'startx' all I get is a blank screen with a mouse cursor that I can move around. I've installed xorg-xinit, xorg-twm, xorg-xclock, and xterm.
I'm not getting any significant errors in the logs, or even the terminal I issue 'startx' in.
I'm not sure what the problem could be...
Here is my output from 'startx'
X.Org X Server 1.13.0
Release Date: 2012-09-05
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.6.0-1-ARCH i686
Current Operating System: Linux x_00294-ibc 3.5.6-1-ARCH #1 SMP PREEMPT Sun Oct 7 19:33:50 CEST 2012 i686
Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ec6a9a60-8d8c-4de0-960b-9e2a044d0ca5 ro quiet
Build Date: 05 October 2012 02:01:30PM
Current version of pixman: 0.26.2
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Oct 13 09:26:12 2012
(==) Using config directory: "/etc/X11/xorg.conf.d"
Initializing built-in extension Generic Event Extension
Initializing built-in extension SHAPE
Initializing built-in extension MIT-SHM
Initializing built-in extension XInputExtension
Initializing built-in extension XTEST
Initializing built-in extension BIG-REQUESTS
Initializing built-in extension SYNC
Initializing built-in extension XKEYBOARD
Initializing built-in extension XC-MISC
Initializing built-in extension SECURITY
Initializing built-in extension XINERAMA
Initializing built-in extension XFIXES
Initializing built-in extension RENDER
Initializing built-in extension RANDR
Initializing built-in extension COMPOSITE
Initializing built-in extension DAMAGE
Initializing built-in extension MIT-SCREEN-SAVER
Initializing built-in extension DOUBLE-BUFFER
Initializing built-in extension RECORD
Initializing built-in extension DPMS
Initializing built-in extension X-Resource
Initializing built-in extension XVideo
Initializing built-in extension XVideo-MotionCompensation
Initializing built-in extension XFree86-VidModeExtension
Initializing built-in extension XFree86-DGA
Initializing built-in extension XFree86-DRI
Initializing built-in extension DRI2
Loading extension GLX
xinit: connection to X server lost
waiting for X server to shut down XIO: fatal IO error 0 (Success) on X server ":0"
after 554 requests (554 known processed) with 0 events remaining.
xterm: fatal IO error 11 (Resource temporarily unavailable) or KillClient on X server ":0"
xterm: fatal IO error 11 (Resource temporarily unavailable) or KillClient on X server ":0"
xterm: fatal IO error 11 (Resource temporarily unavailable) or KillClient on X server ":0"
Server terminated successfully (0). Closing log file.
xinit: unexpected signal 2
And my Xorg.0.log
[ 4955.478]
X.Org X Server 1.13.0
Release Date: 2012-09-05
[ 4955.479] X Protocol Version 11, Revision 0
[ 4955.479] Build Operating System: Linux 3.6.0-1-ARCH i686
[ 4955.479] Current Operating System: Linux x_00294-ibc 3.5.6-1-ARCH #1 SMP PREEMPT Sun Oct 7 19:33:50 CEST 2012 i686
[ 4955.479] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ec6a9a60-8d8c-4de0-960b-9e2a044d0ca5 ro quiet
[ 4955.479] Build Date: 05 October 2012 02:01:30PM
[ 4955.479]
[ 4955.479] Current version of pixman: 0.26.2
[ 4955.479] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 4955.479] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 4955.480] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Oct 13 09:26:12 2012
[ 4955.480] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 4955.480] (==) No Layout section. Using the first Screen section.
[ 4955.480] (==) No screen section available. Using defaults.
[ 4955.480] (**) |-->Screen "Default Screen Section" (0)
[ 4955.480] (**) | |-->Monitor "<default monitor>"
[ 4955.481] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 4955.481] (==) Automatically adding devices
[ 4955.481] (==) Automatically enabling devices
[ 4955.481] (==) Automatically adding GPU devices
[ 4955.481] (WW) The directory "/usr/share/fonts/TTF/" does not exist.
[ 4955.481] Entry deleted from font path.
[ 4955.481] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 4955.481] Entry deleted from font path.
[ 4955.481] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 4955.481] Entry deleted from font path.
[ 4955.481] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 4955.481] Entry deleted from font path.
[ 4955.481] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 4955.481] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 4955.481] Entry deleted from font path.
[ 4955.481] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 4955.481] (==) FontPath set to:
/usr/share/fonts/misc/
[ 4955.481] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 4955.481] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 4955.481] (II) Loader magic: 0x825a620
[ 4955.482] (II) Module ABI versions:
[ 4955.482] X.Org ANSI C Emulation: 0.4
[ 4955.482] X.Org Video Driver: 13.0
[ 4955.482] X.Org XInput driver : 18.0
[ 4955.482] X.Org Server Extension : 7.0
[ 4955.484] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 4955.486] (--) PCI:*(0:0:2:0) 8086:3577:1014:0505 rev 4, Mem @ 0x98000000/134217728, 0x90100000/524288
[ 4955.486] (--) PCI: (0:0:2:1) 8086:3577:1014:0505 rev 0, Mem @ 0x88000000/134217728, 0x80200000/524288
[ 4955.486] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 4955.486] Initializing built-in extension Generic Event Extension
[ 4955.486] Initializing built-in extension SHAPE
[ 4955.486] Initializing built-in extension MIT-SHM
[ 4955.486] Initializing built-in extension XInputExtension
[ 4955.486] Initializing built-in extension XTEST
[ 4955.486] Initializing built-in extension BIG-REQUESTS
[ 4955.486] Initializing built-in extension SYNC
[ 4955.487] Initializing built-in extension XKEYBOARD
[ 4955.487] Initializing built-in extension XC-MISC
[ 4955.487] Initializing built-in extension SECURITY
[ 4955.487] Initializing built-in extension XINERAMA
[ 4955.487] Initializing built-in extension XFIXES
[ 4955.487] Initializing built-in extension RENDER
[ 4955.487] Initializing built-in extension RANDR
[ 4955.487] Initializing built-in extension COMPOSITE
[ 4955.487] Initializing built-in extension DAMAGE
[ 4955.487] Initializing built-in extension MIT-SCREEN-SAVER
[ 4955.487] Initializing built-in extension DOUBLE-BUFFER
[ 4955.487] Initializing built-in extension RECORD
[ 4955.487] Initializing built-in extension DPMS
[ 4955.487] Initializing built-in extension X-Resource
[ 4955.487] Initializing built-in extension XVideo
[ 4955.487] Initializing built-in extension XVideo-MotionCompensation
[ 4955.487] Initializing built-in extension XFree86-VidModeExtension
[ 4955.487] Initializing built-in extension XFree86-DGA
[ 4955.487] Initializing built-in extension XFree86-DRI
[ 4955.487] Initializing built-in extension DRI2
[ 4955.487] (II) LoadModule: "glx"
[ 4955.488] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 4955.489] (II) Module glx: vendor="X.Org Foundation"
[ 4955.489] compiled for 1.13.0, module version = 1.0.0
[ 4955.489] ABI class: X.Org Server Extension, version 7.0
[ 4955.489] (==) AIGLX enabled
[ 4955.489] Loading extension GLX
[ 4955.489] (==) Matched intel as autoconfigured driver 0
[ 4955.489] (==) Matched intel as autoconfigured driver 1
[ 4955.489] (==) Matched vesa as autoconfigured driver 2
[ 4955.489] (==) Matched modesetting as autoconfigured driver 3
[ 4955.489] (==) Matched fbdev as autoconfigured driver 4
[ 4955.489] (==) Assigned the driver to the xf86ConfigLayout
[ 4955.489] (II) LoadModule: "intel"
[ 4955.490] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 4955.491] (II) Module intel: vendor="X.Org Foundation"
[ 4955.491] compiled for 1.13.0, module version = 2.20.9
[ 4955.491] Module class: X.Org Video Driver
[ 4955.491] ABI class: X.Org Video Driver, version 13.0
[ 4955.491] (II) LoadModule: "vesa"
[ 4955.491] (WW) Warning, couldn't open module vesa
[ 4955.491] (II) UnloadModule: "vesa"
[ 4955.492] (II) Unloading vesa
[ 4955.492] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 4955.492] (II) LoadModule: "modesetting"
[ 4955.492] (WW) Warning, couldn't open module modesetting
[ 4955.492] (II) UnloadModule: "modesetting"
[ 4955.492] (II) Unloading modesetting
[ 4955.492] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 4955.493] (II) LoadModule: "fbdev"
[ 4955.493] (WW) Warning, couldn't open module fbdev
[ 4955.493] (II) UnloadModule: "fbdev"
[ 4955.493] (II) Unloading fbdev
[ 4955.493] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 4955.493] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server,
Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2),
Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2),
Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2),
Haswell Server (GT2+), Haswell SDV Desktop (GT1),
Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+),
Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2),
Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1),
Haswell SDV Server (GT2), Haswell SDV Server (GT2+),
Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2),
Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1),
Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+),
Haswell ULT Server (GT1), Haswell ULT Server (GT2),
Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1),
Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+),
Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2),
Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1),
Haswell CRW Server (GT2), Haswell CRW Server (GT2+),
ValleyView PO board
[ 4955.496] (--) using VT number 7
[ 4955.508] (II) intel(0): using device path '/dev/dri/card0'
[ 4955.509] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 4955.509] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 4955.509] (==) intel(0): RGB weight 888
[ 4955.509] (==) intel(0): Default visual is TrueColor
[ 4955.509] (--) intel(0): Integrated Graphics Chipset: Intel(R) i830M
[ 4955.509] (**) intel(0): Relaxed fencing disabled
[ 4955.509] (**) intel(0): Wait on SwapBuffers? enabled
[ 4955.509] (**) intel(0): Triple buffering? enabled
[ 4955.509] (**) intel(0): Framebuffer tiled
[ 4955.510] (**) intel(0): Pixmaps tiled
[ 4955.510] (**) intel(0): 3D buffers tiled
[ 4955.510] (**) intel(0): SwapBuffers wait enabled
[ 4955.510] (==) intel(0): video overlay key set to 0x101fe
[ 4955.593] (II) intel(0): Output VGA1 has no monitor section
[ 4955.593] (II) intel(0): Output LVDS1 has no monitor section
[ 4955.594] (--) intel(0): found backlight control interface /sys/class/backlight/thinkpad_screen
[ 4955.676] (II) intel(0): EDID for output VGA1
[ 4955.677] (II) intel(0): Printing probed modes for output VGA1
[ 4955.677] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 4955.677] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 4955.677] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 4955.677] (II) intel(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e)
[ 4955.677] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 489 492 525 -hsync -vsync (31.5 kHz e)
[ 4955.677] (II) intel(0): EDID for output LVDS1
[ 4955.677] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 4955.677] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 4955.677] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 4955.677] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Printing probed modes for output LVDS1
[ 4955.678] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 +hsync +vsync (48.4 kHz P)
[ 4955.678] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz d)
[ 4955.678] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d)
[ 4955.678] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz d)
[ 4955.678] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d)
[ 4955.678] (II) intel(0): Output VGA1 connected
[ 4955.678] (II) intel(0): Output LVDS1 connected
[ 4955.678] (II) intel(0): Using exact sizes for initial modes
[ 4955.678] (II) intel(0): Output VGA1 using initial mode 1024x768
[ 4955.678] (II) intel(0): Output LVDS1 using initial mode 1024x768
[ 4955.678] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 4955.678] (II) intel(0): Kernel page flipping support detected, enabling
[ 4955.678] (==) intel(0): DPI set to (96, 96)
[ 4955.678] (II) Loading sub module "fb"
[ 4955.678] (II) LoadModule: "fb"
[ 4955.679] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 4955.679] (II) Module fb: vendor="X.Org Foundation"
[ 4955.679] compiled for 1.13.0, module version = 1.0.0
[ 4955.679] ABI class: X.Org ANSI C Emulation, version 0.4
[ 4955.679] (II) Loading sub module "dri2"
[ 4955.679] (II) LoadModule: "dri2"
[ 4955.680] (II) Module "dri2" already built-in
[ 4955.680] (==) Depth 24 pixmap format is 32 bpp
[ 4955.680] (II) intel(0): [DRI2] Setup complete
[ 4955.680] (II) intel(0): [DRI2] DRI driver: i915
[ 4955.680] (II) intel(0): Allocated new frame buffer 1024x768 stride 4096, tiled
[ 4955.680] (II) UXA(0): Driver registered support for the following operations:
[ 4955.680] (II) solid
[ 4955.680] (II) copy
[ 4955.680] (II) composite (RENDER acceleration)
[ 4955.680] (II) put_image
[ 4955.680] (II) get_image
[ 4955.680] (==) intel(0): Backing store disabled
[ 4955.680] (==) intel(0): Silken mouse enabled
[ 4955.681] (II) intel(0): Initializing HW Cursor
[ 4955.681] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 4955.684] (==) intel(0): DPMS enabled
[ 4955.684] (==) intel(0): Intel XvMC decoder disabled
[ 4955.684] (II) intel(0): Set up overlay video
[ 4955.684] (II) intel(0): direct rendering: DRI2 Enabled
[ 4955.684] (==) intel(0): hotplug detection: "enabled"
[ 4955.983] (--) RandR disabled
[ 4956.021] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 4956.021] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 4956.021] (II) AIGLX: enabled GLX_ARB_create_context
[ 4956.021] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 4956.021] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 4956.021] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 4956.021] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 4956.021] (II) AIGLX: Loaded and initialized i915
[ 4956.022] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 4956.023] (II) intel(0): Setting screen physical size to 270 x 203
[ 4956.124] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[ 4956.124] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 4956.124] (II) LoadModule: "evdev"
[ 4956.124] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 4956.125] (II) Module evdev: vendor="X.Org Foundation"
[ 4956.125] compiled for 1.13.0, module version = 2.7.3
[ 4956.125] Module class: X.Org XInput Driver
[ 4956.125] ABI class: X.Org XInput driver, version 18.0
[ 4956.125] (II) Using input driver 'evdev' for 'Power Button'
[ 4956.125] (**) Power Button: always reports core events
[ 4956.125] (**) evdev: Power Button: Device: "/dev/input/event4"
[ 4956.126] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 4956.126] (--) evdev: Power Button: Found keys
[ 4956.126] (II) evdev: Power Button: Configuring as keyboard
[ 4956.126] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event4"
[ 4956.126] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 4956.126] (**) Option "xkb_rules" "evdev"
[ 4956.126] (**) Option "xkb_model" "evdev"
[ 4956.126] (**) Option "xkb_layout" "us"
[ 4956.197] (II) config/udev: Adding input device Video Bus (/dev/input/event2)
[ 4956.198] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 4956.198] (II) Using input driver 'evdev' for 'Video Bus'
[ 4956.198] (**) Video Bus: always reports core events
[ 4956.198] (**) evdev: Video Bus: Device: "/dev/input/event2"
[ 4956.198] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 4956.198] (--) evdev: Video Bus: Found keys
[ 4956.198] (II) evdev: Video Bus: Configuring as keyboard
[ 4956.198] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A03:00/LNXVIDEO:00/input/input2/event2"
[ 4956.198] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 4956.198] (**) Option "xkb_rules" "evdev"
[ 4956.198] (**) Option "xkb_model" "evdev"
[ 4956.198] (**) Option "xkb_layout" "us"
[ 4956.200] (II) config/udev: Adding input device Lid Switch (/dev/input/event3)
[ 4956.200] (II) No input driver specified, ignoring this device.
[ 4956.200] (II) This device may have been added with another device file.
[ 4956.201] (II) config/udev: Adding input device Sleep Button (/dev/input/event1)
[ 4956.201] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 4956.201] (II) Using input driver 'evdev' for 'Sleep Button'
[ 4956.202] (**) Sleep Button: always reports core events
[ 4956.202] (**) evdev: Sleep Button: Device: "/dev/input/event1"
[ 4956.202] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[ 4956.202] (--) evdev: Sleep Button: Found keys
[ 4956.202] (II) evdev: Sleep Button: Configuring as keyboard
[ 4956.202] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1/event1"
[ 4956.202] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 8)
[ 4956.202] (**) Option "xkb_rules" "evdev"
[ 4956.202] (**) Option "xkb_model" "evdev"
[ 4956.202] (**) Option "xkb_layout" "us"
[ 4956.204] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 4956.205] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 4956.205] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 4956.205] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 4956.205] (**) AT Translated Set 2 keyboard: always reports core events
[ 4956.205] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 4956.205] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 4956.205] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 4956.205] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 4956.205] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 4956.205] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 9)
[ 4956.205] (**) Option "xkb_rules" "evdev"
[ 4956.206] (**) Option "xkb_model" "evdev"
[ 4956.206] (**) Option "xkb_layout" "us"
[ 4956.208] (II) config/udev: Adding input device TPPS/2 IBM TrackPoint (/dev/input/event6)
[ 4956.208] (**) TPPS/2 IBM TrackPoint: Applying InputClass "evdev pointer catchall"
[ 4956.208] (II) Using input driver 'evdev' for 'TPPS/2 IBM TrackPoint'
[ 4956.208] (**) TPPS/2 IBM TrackPoint: always reports core events
[ 4956.208] (**) evdev: TPPS/2 IBM TrackPoint: Device: "/dev/input/event6"
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Vendor 0x2 Product 0xa
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Found 3 mouse buttons
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Found relative axes
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Found x and y relative axes
[ 4956.208] (II) evdev: TPPS/2 IBM TrackPoint: Configuring as mouse
[ 4956.208] (**) evdev: TPPS/2 IBM TrackPoint: YAxisMapping: buttons 4 and 5
[ 4956.208] (**) evdev: TPPS/2 IBM TrackPoint: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 4956.208] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input6/event6"
[ 4956.208] (II) XINPUT: Adding extended input device "TPPS/2 IBM TrackPoint" (type: MOUSE, id 10)
[ 4956.209] (II) evdev: TPPS/2 IBM TrackPoint: initialized for relative axes.
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) keeping acceleration scheme 1
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) acceleration profile 0
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) acceleration factor: 2.000
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) acceleration threshold: 4
[ 4956.210] (II) config/udev: Adding input device TPPS/2 IBM TrackPoint (/dev/input/mouse0)
[ 4956.210] (II) No input driver specified, ignoring this device.
[ 4956.210] (II) This device may have been added with another device file.
[ 4956.211] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)
[ 4956.211] (II) No input driver specified, ignoring this device.
[ 4956.211] (II) This device may have been added with another device file.
[ 4956.213] (II) config/udev: Adding input device ThinkPad Extra Buttons (/dev/input/event7)
[ 4956.213] (**) ThinkPad Extra Buttons: Applying InputClass "evdev keyboard catchall"
[ 4956.213] (II) Using input driver 'evdev' for 'ThinkPad Extra Buttons'
[ 4956.213] (**) ThinkPad Extra Buttons: always reports core events
[ 4956.213] (**) evdev: ThinkPad Extra Buttons: Device: "/dev/input/event7"
[ 4956.214] (--) evdev: ThinkPad Extra Buttons: Vendor 0x1014 Product 0x5054
[ 4956.214] (--) evdev: ThinkPad Extra Buttons: Found keys
[ 4956.214] (II) evdev: ThinkPad Extra Buttons: Configuring as keyboard
[ 4956.214] (**) Option "config_info" "udev:/sys/devices/platform/thinkpad_acpi/input/input7/event7"
[ 4956.214] (II) XINPUT: Adding extended input device "ThinkPad Extra Buttons" (type: KEYBOARD, id 11)
[ 4956.214] (**) Option "xkb_rules" "evdev"
[ 4956.214] (**) Option "xkb_model" "evdev"
[ 4956.214] (**) Option "xkb_layout" "us"
[ 4960.630] (II) AIGLX: Suspending AIGLX clients for VT switch
[ 4964.186] (II) evdev: ThinkPad Extra Buttons: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: TPPS/2 IBM TrackPoint: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: AT Translated Set 2 keyboard: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: Sleep Button: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: Video Bus: Close
[ 4964.190] (II) UnloadModule: "evdev"
[ 4964.190] (II) evdev: Power Button: Close
[ 4964.190] (II) UnloadModule: "evdev"
[ 4964.192] Server terminated successfully (0). Closing log file.

karol wrote:
Leonid.I wrote:@0x001A4:
To run twm, you need to install xorg-twm from [extra] (I am not sure if it installs by default). Do you have xterm installed?
According to his first post he has both xorg-twm and xterm installed.
I do indeed.
I went ahead and installed LXDE anyways, just to see what would happen. Exact same thing, it looks like everything is about to load but only the mouse cursor shows up. My Xorg.0.log is the same, so I won't post it again.
I do get an error in the console about the openbox menu.xml file missing but I doubt that's related.
X.Org X Server 1.13.0
Release Date: 2012-09-05
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.6.0-1-ARCH i686
Current Operating System: Linux x_00294-ibc 3.5.6-1-ARCH #1 SMP PREEMPT Sun Oct 7 19:33:50 CEST 2012 i686
Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ec6a9a60-8d8c-4de0-960b-9e2a044d0ca5 ro quiet
Build Date: 05 October 2012 02:01:30PM
Current version of pixman: 0.26.2
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Oct 15 18:12:28 2012
(==) Using config directory: "/etc/X11/xorg.conf.d"
Initializing built-in extension Generic Event Extension
Initializing built-in extension SHAPE
Initializing built-in extension MIT-SHM
Initializing built-in extension XInputExtension
Initializing built-in extension XTEST
Initializing built-in extension BIG-REQUESTS
Initializing built-in extension SYNC
Initializing built-in extension XKEYBOARD
Initializing built-in extension XC-MISC
Initializing built-in extension SECURITY
Initializing built-in extension XINERAMA
Initializing built-in extension XFIXES
Initializing built-in extension RENDER
Initializing built-in extension RANDR
Initializing built-in extension COMPOSITE
Initializing built-in extension DAMAGE
Initializing built-in extension MIT-SCREEN-SAVER
Initializing built-in extension DOUBLE-BUFFER
Initializing built-in extension RECORD
Initializing built-in extension DPMS
Initializing built-in extension X-Resource
Initializing built-in extension XVideo
Initializing built-in extension XVideo-MotionCompensation
Initializing built-in extension XFree86-VidModeExtension
Initializing built-in extension XFree86-DGA
Initializing built-in extension XFree86-DRI
Initializing built-in extension DRI2
Loading extension GLX
Openbox-Message: Unable to find a valid menu file "/usr/share/lxde/openbox/menu.xml"
xinit: connection to X server lost
waiting for X server to shut down pcmanfm: Fatal IO error 11 (Resource temporarily unavailable) on X server :0.
XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0"
after 2326 requests (2323 known processed) with 0 events remaining.
Server terminated successfully (0). Closing log file.
xinit: unexpected signal 2
.xinitrc for my user
exec ck-launch-session startlxde
Very wierd.

Apple Cinema 23" on a PC? can't get it to work just has a blank screen?

Sorry this may have been asked a million times but i have a 23" cinema HD display and i'm try to connect it to a laptop PC with the convertor to vga and no matter what i try it has a blank screen with the white power light. I have tried to change the res to the lowest it doesn't work what am i doing wrong please help!!

You can't use a simple VGA to DVI adapter, since VGA doesn't have the digital video signals needed by Apple displays. You need a VGA to DVI converter, such as
<http://www.gefen.com/kvm/dproduct.jsp?prod_id=4341>

Tried installing Windows Vista, cancelled install and now it won't boot from the OEM Vista DVD, all i get is BOOTMGR is missing error... Ctrl Alt Del to restart and when i turn the computer on i get a blank screen and pressing C is not working to boot....

Topic says it all...
My friend started a installation of Windows Vista, but pulled out after deleting all partitions...
So now i power it on, get a blank screen (seems a bit gray because of backlighting, should show the apple logo right?)...
Then after like 15-20sec it will throw out a:
BOOTMGR is missing
Press Ctrl+Alt+Del to restart
I have a OEM Windows Vista DVD in the drive, and i know... Windows 7 is better... but i'm not that fond of stealing software from Microsoft and i have 10 licenses for Vista...
I have tried pressing C while booting up but it doesn't work...
Does anyone here have a magic soloution for me, and no i will not install MacOS on it !!!

Deleting Boot Camp partitions the conventional way will not work . You must use the Boot Camp Assistant to remove a Boot Camp partition. Here is a link to the guide.
http://manuals.info.apple.com/en_US/Boot_Camp_Install-Setup_10.6.pdf
The way to restart is to hold down the option/alt key during startup* and then selecting the Mac OS. If you have a valid Boot Camp install of Windows it would show up during this type of start up.
* hold down immediately after pressing the power button and until the OS choice screen appears.
To summarize.
1 Use the above method to boot into Mac OS.
2 Download the instructions and read them.
3 Use Boot Camp Assistant to remove the partition.
4 Pick your friends more carefully.

When I click on picture in Photo Gallery...just blank screen...no picture

Hi. I have been doing well with iPhoto until I tried to migrate to Aperture. When I migrated to Aperture, I deleted the iPhoto library in Aperture as I read in the tutorial.
Clearly, I did something wrong. Well, I uninstalled Aperture and will be using that at another time, but for now here is my dilemma.
Since I migrated photos to Aperture, consolidated them with iPhoto and then deleted...
now I open my iPhoto and double click on a photo to edit or view...and nothing appears. Just blank screen. The small pics are at the top but it doesn't open to a larger picture. Where are my photos! Help!
Image: !http://www.facebook.com/photo.php?fbid=10150106481305832&set=a.101501064812108 32.307068.555810831!

The previews you refer to are the thumbnails in the iPhoto Library - iPhoto creates them when you import a photo.
Aperture has the ability to trash Referenced Files. If you imported the files to Aperture as Referenced and then trashed them from Aperture, are you sure you didn't also tell it to trash the Referenced Files. This would produce exactly the scenario that you describe.
Regards
TD

Acrobat XI Pro - I see a blank screen in PDF portfolio

I am not sure what I'm supposed to see but after creating a pdf portfolio and choosing 5 files, all I see is a blank screen. I try to add files again (thinking I did somehting wong) an it says they are already there. Help if you can. I'm new to this program but not to computers. This is what I see after adding files. Thank you!

Hi Dave,
I have the same problem except when I click the button to install Flash (I have the latest anyway) Acrobat hangs.
Rob.

YouTube will not work on safari for me on the ipad. Is there anyway to fix this? I can go anywhere else on the internet fine and it works on google chrome, but on safari it shows a blank screen with the bar on top after it loads.

YouTube will not work on safari for me on the ipad. Is there anyway to fix this? I can go anywhere else on the internet fine and it works on google chrome, but on safari it shows a blank screen with the bar on top after it loads, if it's even loading at all.
I do not know if it's relevant or not, but I got a message on my ipad while on safari saying that my iPhone has a virus. I looked it up and it seems it might have just been an ad from the website I was on, but it happened around the same time YouTube stopped working.

You will find that using the YouTube app will provide a better viewing experience for YouTube videos.

My Adobe CC opens to a blank screen. Any suggestions?

I have Adobe CC installed on my HP Win7 laptop. It opens to a blank screen. Has this happend to anyone else?

this does not work with iphone 5. changing date to 2013 does not work. resetting phone does not work.

Getting blank screen when i try to open workspace first time

Hi All,
I have installed hyperion 11.1.2.2 version with Oracle 11.2.0.1 database. Installation and configuration completed successfully.
Operating System: Windows Server 2008 64 bit
When i try to open workspace, it is showing blank page in the IE 10
error msg:
<May 7, 2013 4:29:30 AM MST> <Notice> <WebLogicServer> <BEA-000365> <Server stat
e changed to RUNNING>
<May 7, 2013 4:29:30 AM MST> <Notice> <WebLogicServer> <BEA-000360> <Server star
ted in RUNNING mode>
*<May 7, 2013 4:29:30 AM MST> <Warning> <Log Management> <BEA-170011> <The LogBro*
adcaster on this server failed to broadcast log messages to the admin server. Th
e Admin server may not be running. Message broadcasts to the admin server will b
e disabled.>
<May 7, 2013 4:37:20 AM MST> <Warning> <Socket> <BEA-000449> <Closing socket as
no data read from it on fe80:0:0:0:21c:42ff:fe6e:b382:61,983 during the configur
ed idle timeout of 5 secs>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090171> <Loading the ident
ity certificate and private key stored under the alias DemoIdentity from the jks
keystore file C:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\DemoIdentity.jks.>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090169> <Loading trusted c
ertificates from the jks keystore file C:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\
DemoTrust.jks.>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090169> <Loading trusted c
ertificates from the jks keystore file C:\Oracle\MIDDLE~1\JROCKI~1\jre\lib\secur
ity\cacerts.>
<May 7, 2013 4:38:08 AM MST> <Alert> <Security> <BEA-090152> <Demo trusted CA ce
rtificate is being used in production mode: [
Version: V3
Subject: CN=CACERT, OU=FOR TESTING ONLY, O=MyOrganization, L=MyTown, ST=MyStat
e, C=US
Signature Algorithm: MD5withRSA, OID = 1.2.840.113549.1.1.4
Key: Sun RSA public key, 512 bits
modulus: 955019287786924425883848070339045601504642537525227827919067306354412
25109254821799633292360521460473564159575876280112824847724589839778989962768154
40753
public exponent: 65537
Validity: [From: Thu Mar 21 13:12:27 MST 2002,
To: Tue Mar 22 13:12:27 MST 2022]
Issuer: CN=CACERT, OU=FOR TESTING ONLY, O=MyOrganization, L=MyTown, ST=MyState
, C=US
SerialNumber: [ 33f10648 fcde0deb 4199921f d64537f4]
Certificate Extensions: 1
[1]: ObjectId: 2.5.29.15 Criticality=true
KeyUsage [
Key_CertSign
Algorithm: [MD5withRSA]
Signature:
0000: 9D 26 4C 29 C8 91 C3 A7 06 C3 24 6F AE B4 F8 82 .&L)......$o....
0010: 80 4D AA CB 7C 79 46 84 81 C4 66 95 F4 1E D8 C4 .M...yF...f.....
0020: E9 B7 D9 7C E2 23 33 A4 B7 21 E0 AA 54 2B 4A FF .....#3..!..T+J.
0030: CB 21 20 88 81 21 DB AC 90 54 D8 7D 79 63 23 3C .! ..!...T..yc#<
] The system is vulnerable to security attacks, since it trusts certificates sig
ned by the demo trusted CA.>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090898> <Ignoring the trus
ted CA certificate "CN=Entrust Root Certification Authority - G2,OU=(c) 2009 Ent
rust\, Inc. - for authorized use only,OU=See www.entrust.net/legal-terms,O=Entru
st\, Inc.,C=US". The loading of the trusted certificate list raised a certificat
e parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2
.840.113549.1.1.11.>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090898> <Ignoring the trus
ted CA certificate "CN=thawte Primary Root CA - G3,OU=(c) 2008 thawte\, Inc. - F
or authorized use only,OU=Certification Services Division,O=thawte\, Inc.,C=US".
The loading of the trusted certificate list raised a certificate parsing except
ion PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.
11.>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090898> <Ignoring the trus
ted CA certificate "CN=T-TeleSec GlobalRoot Class 3,OU=T-Systems Trust Center,O=
T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate
list raised a certificate parsing exception PKIX: Unsupported OID in the Algori
thmIdentifier object: 1.2.840.113549.1.1.11.>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090898> <Ignoring the trus
ted CA certificate "CN=T-TeleSec GlobalRoot Class 2,OU=T-Systems Trust Center,O=
T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate
list raised a certificate parsing exception PKIX: Unsupported OID in the Algori
thmIdentifier object: 1.2.840.113549.1.1.11.>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090898> <Ignoring the trus
ted CA certificate "CN=GlobalSign,O=GlobalSign,OU=GlobalSign Root CA - R3". The
loading of the trusted certificate list raised a certificate parsing exception P
KIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090898> <Ignoring the trus
ted CA certificate "OU=Security Communication RootCA2,O=SECOM Trust Systems CO.\
,LTD.,C=JP". The loading of the trusted certificate list raised a certificate pa
rsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840
.113549.1.1.11.>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090898> <Ignoring the trus
ted CA certificate "CN=VeriSign Universal Root Certification Authority,OU=(c) 20
08 VeriSign\, Inc. - For authorized use only,OU=VeriSign Trust Network,O=VeriSig
n\, Inc.,C=US". The loading of the trusted certificate list raised a certificate
parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.
840.113549.1.1.11.>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090898> <Ignoring the trus
ted CA certificate "CN=KEYNECTIS ROOT CA,OU=ROOT,O=KEYNECTIS,C=FR". The loading
of the trusted certificate list raised a certificate parsing exception PKIX: Uns
upported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<May 7, 2013 4:38:08 AM MST> <Notice> <Security> <BEA-090898> <Ignoring the trus
ted CA certificate "CN=GeoTrust Primary Certification Authority - G3,OU=(c) 2008
GeoTrust Inc. - For authorized use only,O=GeoTrust Inc.,C=US". The loading of t
he trusted certificate list raised a certificate parsing exception PKIX: Unsuppo
rted OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<May 7, 2013 4:39:00 AM MST> <Warning> <Socket> <BEA-000449> <Closing socket as
no data read from it on fe80:0:0:0:21c:42ff:fe6e:b382:62,088 during the configur
ed idle timeout of 5 secs>
<May 7, 2013 4:42:50 AM MST> <Warning> <Socket> <BEA-000449> <Closing socket as
no data read from it on fe80:0:0:0:21c:42ff:fe6e:b382:62,321 during the configur
ed idle timeout of 5 secs>
Thanks,
mady
Edited by: mady on May 7, 2013 5:27 PM

Did you configure the web server as the last part of foundation services? You could always get a patch for IE support but the blank screen always appears if the services wasn't started up correctly or if the web server wasn't configured lastly after any configuration change.
About the Weblogic here's where you can get more info about your error message: http://docs.oracle.com/cd/E12839_01/apirefs.1111/e14397/LogMgmt.html
"BEA-170011
Warning: The LogBroadcaster on this server failed to broadcast log messages to the admin server. The Admin server may not be running. Message broadcasts to the admin server will be disabled.
Description
The LogBroadCaster on the managed server could not find a reference to the DomainLogHandler on the admin server. Messages from this server will not be logged in the domain log.
Cause
The managed server might not be able to reach the admin server. One of the possible causes could be due to the admin server being shutdown.
Action
To fix this problem, inspect the exception stack trace, correct the problem. If the admin server is shutdown, restart it to resume normal log broadcasting to the domain."
Just my 2cents...

My Iphone 5s blank screen and can hear voice command when i press the home button

My Iphone 5s was coming up with voice command and driving me nuts. After trying to reset the phone now I just have a blank screen. when i goes to restart the apple icon will show then the voice command lady will talk in the back ground but still no screen.
Any help please

Try one of these 4Rs toubleshooting steps:
Restart:
1. Press and hold the Sleep/Wake button until the red "slide to power off" slider appears, and then slide the slider.
2. Press and hold the Sleep/Wake button until the Apple logo appears.
Reset: Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Note: You will not lose any data
Restore from backup
Restore as new
http://support.apple.com/kb/HT1414

I connected an external monitor to my MacBook Pro, but it doesn't open any programs. It Just sits there with a blank screen. How do I get it to open programs and act like a monitor?

I connected an external monitor to my MacBook Pro, but it doesn't open any programs. It Just sits there with a blank screen. How do I get it to open programs and act like a monitor?

Dear Jean:
It sounds like you are trying to get your external monitor to act as the primary viewing screen. For example it would have your Doc, Icons, Etc. In order to make the external monitor the primary screen you have to:
Open System Preferences.
Choose the Displays Icon
There will be several tabs to choose from pick Arrangement
Drag the toolbar to desired display
Let me know if this helps at all!
Lance

Blank screen on HP pavillion tx 2500

Similar Messages

Maybe you are looking for