Blank vertical spacing too large

In the process of creating a website and unable to shorten
the gap between an h2 and new line. Can someone please advise. To
see what I'm talking about:
http://www.waynebsmithinc.com/barge/index.html.
I want the bulleted text directly under the headings, without the
large gap. Can this be done and if so, how? Thanks,

Your h2 has a bottom margin of 20 px, your ul has a top
margin of 16px. Set
the ul top margin to 0 and then reduce the h2 bottom margin
as needed.
Walt
"Murrel" <[email protected]> wrote in
message
news:gp8md0$l5e$[email protected]..
> In the process of creating a website and unable to
shorten the gap between
> an
> h2 and new line. Can someone please advise. To see what
I'm talking
> about:
>
http://www.waynebsmithinc.com/barge/index.html.
I want the bulleted text
> directly under the headings, without the large gap. Can
this be done and
> if
> so, how? Thanks,
>

Similar Messages

Disk Utility: Creating a new blank image receiving "file too large" error.

Hello All!
I'm trying to create a 10GB non-encrypted, non-compressed RW blank image via the disk utility. The DU runs for a few minutes then barfs out "file too large" error. I have over 30GB free on my HDD. I tried with a smaller size of 6GB to no avail. Also tried unsuccessfully to create from a file (about 4 GB). My ultimate goal is to create a case-insensitive image to run an extremely important program needed for high priority work productivity (i.e. WoW). Thanks in advance for any advice! You will be my new best friend if you help me resolve this. =D
Hollie
"There are only 10 types of people in this world: Those who understand binary, and those who don't."

Hi Hollie, and welcome to the forums!
Have you created images before successfully?
Is this to/on your boot drive, or an external drive?
Have you done any Disk/OS maintenance lately?
We might see if there are some big temp files left or such...
How much free space is on the HD, where has all the space gone?
OmniDiskSweeper is now free, and likely the best/easiest...
http://www.omnigroup.com/applications/omnidisksweeper/
WhatSize...
http://www.macupdate.com/info.php/id/13006/
Disk Inventory X...
http://www.derlien.com/
GrandPerspective...
http://grandperspectiv.sourceforge.net/

Query is too large

Hi,
Can any one give me the solution to develop this report.
I have 12 columns under each vertical.Like that i have 12 verticals for my Gross margin Report.
Then 12* 12=144 coloumns.total are 144.
But in Bi-Bex it will allow only limited columns. When i execute the report i'm getting the error that query is too large.Kow to overcome this.
Note Points :
Vertical1 : ITG
This Vertical consists of 20 Profit centers
Vertical2 : UTG
                This Vertical consists of 60 Profit centers
Vertical3 : SBI
                This Vertical consists of 50 Profit centers
Vertical4 : SERVICEDIVISIONS
                This Vertical consists of 10 Profit centers
Vertical5 : ENGG
                This Vertical consists of 50 Profit centers
Vertical6 : HITECH
                This Vertical consists of 10 Profit centers
u2022     Data Before Eliminations is Total of All the Verticals Data.
u2022     Eliminations Contains Values For Each Month for any of the above profit centers.
u2022     Data After Eliminations is Data Before Eliminations + Eliminations Data.
I searched in SDN but no luck..........
Thanks

hi sony,
one way to go about this is to increase the "Size Restriction for Result Sets". This is pretty tricky. I wouldn't really recommend this since this can have performance issues.
you can increase the size for result sets by running the abap report SAP_RSADMIN_MAINTAIN , Again be carefull when you are doing this.
Follow the below steps.
1)     Transaction Code SA38 or SE38
2)     In the program field, enter the report name SAP_RSADMIN_MAINTAIN and choose Execute.
3)     For OBJECT, enter one of the following parameters;
        BICS_DA_RESULT_SET_LIMIT_DEF
        BICS_DA_RESULT_SET_LIMIT_MAX
For VALUE, enter the value for the size of the result set, and then execute the program:
Also, for your information, the default setting for the result set of Web applications is 500,000 cells. If the result set exceeds the size specified using the report, a message is displayed to inform the user.
I would again ask you to be careful when you are modifying these values.
Best would be to make sure that you check the table RSADMIN, whether you have the above entries (BICS_*), if you don't u can update these entries in the system. via the above said abap report.
Hope this helps.
regards,
Sree.
Edited by: Sree Nair on Aug 18, 2009 1:14 PM
Edited by: Sree Nair on Aug 18, 2009 1:23 PM

Whats going on when after i have put my new project it tells me that cannot burn because my encode it too large for DVD

I am trying to convert a video into a dVd i did one and it will not play on my blueray, but, at least it will do on my computer. Now i am trying to do a different dvd and it tells me after i have downlowed my new project, that i cannot burn the idvd because it is too large check my encoded?

The reason why your DVD will not play maybe your choice of disk.
Was it a DVD + or DVD - ?
Always use a good quality DVD blank disk, at least Verbatim and check what format your player will play.
Next, to achieve the best quality export from iMovie, Share your Project to Media Browser.
Then open iDVD and use the media button (bottom right) to import your movie.
A possible reason that you are getting a too large error message is the time length of your DVD.
The default setting in iDVD for Encoding is Best Performance (60mins) and you need to change this to either High Qualirty or Professional Quality which will allow more to be encoded on the disc (120 mins).
iDVD > Project > Project Info > Encoding to change this setting and see on the Capacity slider if your project will fit.
Otherwise check how much free space you have on your HD.
Z.
PS Slow your burn speed down to x4 for error free results.

Vertical spacing out of wack in IE, but perfect in Safari?

I have newbie question about vertical spacing in the frame
based design of the site I am working on. I did not design the
website but I was just asked to take over the basic updating and
maintenance of the content.
www.brainoptimization.com
When I view my site in IE or Safari for Windows it looks just
the way it is supposed to.
But when viewed in Internet Explorer for windows the vertical
spacing in the left column (as well as the spacing between the
first 5 paragraps in the right column) is completely out of whack!
IE for win puts huge chucks of space between the cells where none
was put. Any idea what is going on and how I can correct this
issue? I am using Dreamweaver 8 on a mac. Any help would be
appreciated. Thank you.
Cheers.

Not sure how that page would look perfect in any browser
truthfully :-)
In Firefox there are huge pages in the left column. That
mosaic picture is
about halfway down the page. The styling of the paragraphs is
all over the
place because nearly every paragraph on the page has a new
style applied to
it. From the code I can see well over 100 'styles' ....
someone has really
overdone the use of creating new styles - or using the
property inspector to
create new styles for each paragaph. There are numerous empty
cells with
the table structure, many colspans etc., that make for a very
fragile page
indeed - hence the reason for it not working cross
browser/platform.
In all honesty, I would start over - it looks like a simple 2
column
structure and shouldn't be a problem with getting it to
display correctly in
*every* browser :) Sorry for the bad news.
One thing you can try first off at least (I haven't looked at
the code too
much after seeing all those styles)., place the mouse cursor
into the left
column and in the property inspector set the vertical
alignment to 'top'.,
maybe that will move the contents of that left column to the
top rather than
half way down the page... may or may not work - depending on
whether those
colspans get in the way.
Nadia
Adobe® Community Expert : Dreamweaver
CSS Templates |Tutorials |SEO Articles
http://www.DreamweaverResources.com
~ Customisation Service Available ~
http://www.csstemplates.com.au
"Lightlover" <[email protected]> wrote in
message
news:[email protected]...
> I have newbie question about vertical spacing in the
frame based design of
> the
> site I am working on. I did not design the website but I
was just asked to
> take
> over the basic updating and maintenance of the content.
>
>
http://www.brainoptimization.com
>
> When I view my site in IE or Safari for Windows it looks
just the way it
> is
> supposed to.
>
> But when viewed in Internet Explorer for windows the
vertical spacing in
> the
> left column (as well as the spacing between the first 5
paragraps in the
> right
> column) is completely out of whack! IE for win puts huge
chucks of space
> between the cells where none was put. Any idea what is
going on and how I
> can
> correct this issue? I am using Dreamweaver 8 on a mac.
Any help would be
> appreciated. Thank you.
>
> Cheers.
>

Uploading flash, how much is too large?

Hi, I am trying to create a web site suing adobe Dreamweaver and flash, for the first time.
I am trying to upload a webpage that contains swf.
When I check mu site I could only see a blank page with the webpage title at the top of the page.
When I contacted the webhosting company they say they can see the message that a newer version of adobe flash player is required.
From my computer I cannot even see the message.
The helpdesk person said there are possibly two reasons for it. Either there is a problem with the code in flash or it is too large.
The size of files I uploaded as follows:
HTML: 4KB
Scripts: 37 KB
(The size of swf is 29KB which I did not upload)
Are they too large to upload? If so, what is the maximum size of file can I upload on a webpage?
I know they are basic questions but I am trying to create website on my own.
I would appreciate some friendly advice.

If the html page is supposed to contain the Flash file, then you need to uploadc the Flash file (swf). html pages are simply text files that define content. If any of that content happens to be another file, such as an image or sound or swf file, then you need to also upload those files.

Crystal Reports 9: Page Header plus Page Footer is too large for the page.

Hi,
I have a report that has the following sections.
GH1
GH2a
GH2b - has a sub report
GH2c - has another sub report
GH3
GH4
GH5
details - suppressed
GF5 - suppressed
GF4 - suppressed
GF3 - suppressed
GF2 - suppressed
GF1 - suppressed
The report works fine wehn I run it using Crystal Designer.I am using CR version 9.2.2.693.
When I try to load the report in my application, I get the following error.
Crystal Report Windows Forms Viewer
Page Header plus Page Footer is too large for the page.Error in File rptName.rpt:
Page header or footer longer than a page.
OK
There are no 'suppress blank sections' option set in the sections where the sub-Reports are.
I also tried setting the No Default Printer option.
The report gets loaded from the application only when I set 'New Page after' in the sections where there are sub-Reports.
I do not want to do this; Is there a workaround?
Thank you.

Can someone tell me if this problem is being worked on as it looks as thogh none of the problems regarding the message u2018Page Header plus Page Footer is too large for the pageu2019 have been addressed.
We have several reports that were written in Crystal 7 (I think) and worked in Crystal 9 and X1R2 but now give the above error. We have tried jigging the report in line with the various suggestions but at best can get them to run through successfully with one lot of data and then fail on the second or subsequent pages when you vary the data or report format even slightly. We can report on every bit of data separately or in various combinations but not in others. Changing the bottom page margin by 0.01 cm can cause it to fail on page 7 instead of page 530 (for example). We certainly do not have large page headers (just over 2cm) or page footers (about 0.3cm). We do have some subreports in the details section but have used 'fit to section', added 'keep together', removed u2018keep togetheru2019 from just about everything we can (in desperation) but to no avail. We cannot see a pattern to what is happening. It would be encouraging to know that someone is actually working on this fault.

Sqlldr ORA-01401: inserted value too large for column

export nls_characterset
WE8ISO8859P1
import nls_characterset
AL32UTF8
Here is how my control file looks like
LOAD DATA
INFILE 'db_service.dat'
INTO TABLE DB_SERVICE
FIELDS TERMINATED BY ','
TRAILING NULLCOLS
APPS_ID CHAR NULLIF (APPS_ID=BLANKS)
, LCR_CODE CHAR NULLIF (LCR_CODE=BLANKS)
, SERVICE_ID CHAR NULLIF (SERVICE_ID=BLANKS)
, STARTTIME CHAR NULLIF (STARTTIME=BLANKS)
, ENDTIME CHAR NULLIF (ENDTIME=BLANKS)
, ROUTE_CODE_LEGA CHAR NULLIF (ROUTE_CODE_LEGA=BLANKS)
, ROUTE_CODE_LEGB CHAR NULLIF (ROUTE_CODE_LEGB=BLANKS)
, ACTIVE_DATE DATE "DD-MON-YYYY HH24:MI:SS" NULLIF (ACTIVE_DATE=BLANKS)
, TERMINATE_DATE DATE "DD-MON-YYYY HH24:MI:SS" NULLIF (TERMINATE_DATE=BLANKS)
, CREATE_ON DATE "DD-MON-YYYY HH24:MI:SS" NULLIF (CREATE_ON=BLANKS)
, CREATE_BY CHAR NULLIF (CREATE_BY=BLANKS)
command line used
sqlldr userid=prod@webdevelopment control=D:\oracle\useful-oracle\dba\sqlldr\route_mgmt\control_20080813.ctl data=D:\oracle\useful-oracle\dba\sqlldr\route_mgmt\export_20080813.csv direct=true log=D:\oracle\useful-oracle\dba\sqlldr\route_mgmt\export_20080813.log
but I always encounter
ORA-01401: inserted value too large for column
so how should I resolve this issue?
thanks

hi
ORA-01401
ORA-01401:     inserted value too large for column
Cause:     The value entered is larger than the maximum width defined for the column.
Action:     Enter a value smaller than the column width or use the MODIFY option with ALTER TABLE to expand the column width.
check out this link from burleson ....
http://www.dba-oracle.com/sf_ora_01401_inserted_value_too_large_for_column.htm
hope this helps
CHeers

Dual Monitor Issue: 2nd Display too large...can't adjust...web pages provide no scroll bars

I have two (2) HP S2031 LCD flat screen monitors. They functioned perfectly with my old 32-bit machine (now gone). I have just purchased a new 64-bit Windows 7 machine. There are no error messages, but if I open a web page on the right (2nd) monitor, it does not display correctly. It's as if it is a little too large. I've tried adjusting the image using the Nividia software and using the monitor adjustments without improvement. It is difficult getting out of that window because no scroll bars (vertical or horizontal) present themselves. I am connecting through an iogear MiniView KVM switch to DVi-D sockets (with the four pins).
Is it a 64-bit driver issue? I think not, because display #1 looks fine. Could it be an iogear KVM firmware issue?
I dug out the HP driver disks that came with my monitors and installed them. After I did that, I realized these were a 32-bit installation. Now the monitor resolution won't go back to the higher, recommended level. I don't see the software installation on the "add/remove programs" listing. I'd like to change that.
BUT THE REAL ISSUE is that I need BOTH monitors to be able to display proper aspect independently. Remember, I've been through both the Nividia adjustments menu and the built-in monitor adjustments menu and found nothing that worked so far.
Please help if you can. This is for my trading business and I need it desperately.

When requesting assistance, please provide the brand and model name and/or product number of the computer in question. Without this information, it may be difficult or impossible to resolve your issue.
Have you swapped the two monitors to see if the problem follows the monitor or remains at the same location??? Try that first... if the problem follows the monitor, perform a hard reset by unpluging the monitor from power then holding the power button for 30 seconds. If the problem stays in the same location, you know both monitors are good and I would suspect the KVM isn't passing the "EDID" data to the computer. Removing the KVM should will tell you if this is the case.
Please post back with your troubleshooting results.
Please send KUDOs
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Backing up issues....the file is too large

I have a computer with a CD Burner. Im trying to do a backup of my Itunes purchases and i put a blank cd-r disk in and i get the error that reads something like "the file is too large for the disk, please insert a disk that..." I have tried deselecting and deleting my video's, movies, etc from my purchased list and it still wont back up and i get the same error. I dont even
get the option to insert multiple disks as the last time i backed up it took up 7 disks. Im thinking its probably trying to backup my videos, probably and without a dvd burner its not able to...can i just get it to back up my songs only or what else can I do without deleting my videos from ITUNES all together?
Thanks!

So now that you have repeated the same thing three times that doesn't make things any clearer at all.
You are copying files from where to where?
How are you attempting to copy files, software or click and drag?
Any other detail would be helpful.
Allan

Netware 6 Capture.exe too large for DOS apps.

I am about to upgrade to Netware 6.0 from Netware 3.12 but my tests have
shown that an old DOS application that we use, cannot run the Capture.exe
program shipped with Netware 6.0 because it is too big. The Program calls
batch jobs which execute the Capture program but it fails due to lack of
memory. I have tried using the Capture.exe program from the Netware 3.12
server but for some reason this only works for the admin user account??.
If the program is run using a normal user account, it just echo's a blank
line? If anyone knows of a small 3rd party capture program or any other
solution to this problem, it would be much appreciated.
Thanks.

You also failed to mention the client OS.
The Too Large error seems odd.
http://www.pcounter.com/dosprint.html is a good alternate tool if you can't get
login scripts working.
AndersG wrote:
> ,
> > I am about to upgrade to Netware 6.0 from Netware 3.12 but my tests have
> > shown that an old DOS application that we use, cannot run the Capture.exe
> > program shipped with Netware 6.0 because it is too big. The Program calls
> > batch jobs which execute the Capture program but it fails due to lack of
> > memory. I have tried using the Capture.exe program from the Netware 3.12
> > server but for some reason this only works for the admin user account??.
> > If the program is run using a normal user account, it just echo's a blank
> > line? If anyone knows of a small 3rd party capture program or any other
> > solution to this problem, it would be much appreciated.
> >
> Must it run capture.exe? can't you capture from the login script?
>
> - Anders Gustafsson, Engineer, CNE6, ASE
> NSC Volunteer Sysop (http://support-forums.novell.com)
> Pedago, The Aaland Islands (N60 E20)
> Using VA 4.52 build 277 (32-bit) on Windows 2000 build 2195

Can't burn DVD, file too large?

I downloaded a movie to my hard drive using Drive-In. I am now trying to burn the movie file onto a blank disk but keep getting this error message: "DVD is too large to fit on the disk. Remove some files and try again." Now the file size is 44KB, the disk can hold 4.7GB. Can anyone make sense of this? I opened a burn folder and dragged the movie file into it, do I need to do something else to the file or am I doing it the wrong way? Thanks in advance. Boston

"Drive-in preserves the DVD’s original content protection. Drive-in allows you to play your images on any computer that you own but does not allow you to share your images with others." from Flip4Mac Drive-In web site.
You can not burn that file.
Go to RipDifferent.com to learn how to do what you want to do.

Vi alertlog -- tmp file too large

Hi,
when I try to take a look at alertlog.
It says tmp file too large.
is it something to do with /tmp space?
how can i see the content, its about 3G now
if split might work, can you provide the eg.
Thanks.

jdba wrote:
Thanks sb, it work'd....just my mind is blank for silly things... :)Please be aware that there have been cases reported on this forum where people have lost so much of their db that the only record of their init parms is what is recorded in the alert log at startup. Rather that blowing away everything except the last 500 lines (which could easily be not far enough back to include the most recent startup, I'd suggest a regular routing of renaming the existing alert log to some backup name. I'd want to keep at least enough alert log history to go back to the most recent TWO startups.
Edited by: EdStevens on Sep 17, 2011 10:04 AM

What is up with my vertical spacing?

I can't figure out why my vertical spacing in my left side column is off. No matter what I do, all the elements want to spread themselves and I want them to be towards the top. I'd appreciate it if someone could look at this site for me and maybe offer some insight as to what I'm doing wrong here. The URL is http://www.agrabest.com. The index page is not as much of a problem as the subsequent pages, simply because of the page length, I believe. Thanks so much for any help!

I have recreted a table for you that contains the content from you broccoli page as an example You do not need a table cell to cneter protions of an individual cell - you can use a di, in this case with a class="ctr", and add this to yoru css :
.ctr {
    text-align: center;
I have not attempted to do this precisely matching yorus. But it does let you see how to do this without nexting lots of tables or using lots of table cells:
<table width="100%" border="0" cellspacing="0">
            <tr>
              <td valign="top"><img src="images/popatoplogo.jpg" width="164" height="184">
                <ul id="MenuBar1" class="MenuBarVertical">
      <li><a href="harvester.html">Broccoli Floret Harvester</a></li>
      <li><a href="3-in-1_unit.html">3-in-1 Online Unit</a></li>
      <li><a href="broccoli_online_unit.html">Broccoli Online Floret Unit</a></li>
      <li><a href="cauliflower_online_unit.html">Cauliflower Online Floret Unit</a></li>
      <li><a href="clients.html">Satisfied Clients</a></li>
      <li><a href="index.html">Home</a></li>
    </ul>
     <div class="ctr">
                  <p>Dealer inquiries from<br>
                  all countries welcome!                    </p>
                  <p class="style1">Agra-Best, LLC<br>
                    P.O. Box 1854<br>
                  Bakersfield, CA 93303</p>
                  <p class="style1">David Vargas<br>
                    661.477.3663<br>
                  <a href="mailto:[email protected]">[email protected]</a></p>
                  <p class="style1">Keith Randall<br>
                    661.243.6421<br>
              <a href="mailto:[email protected]">[email protected]</a>    </p>          </div></td>
              <td width="6" bgcolor="#254925"> </td>
              <td valign="top"><h2><span class="style2">Broccoli & Cauliflower Floretting Field Harvesting Machine</span></h2><img src="images/harvester.jpg" width="575" height="259">
              <p>This machine uses a developed "cutting edge" technology to deliver cutting consistency and convenience while minimizing the need for hand labor.</p>
                <ul>
                  <li>Designed for a large variety of broccoli and cauliflower types and dimensions.</li>
                  <li>Harvester has the capacity of floretting 52-60 units per minute, or 900 to 1200 lbs per hour with a single-row harvester; 672 units per minute and up to 10,000 lbs per hour with a 12-row harvester.</li>
                  <li>Reduces labor by 60% over hand harvesting!</li>
                  <li>Core waste materials are automatically fed out of the harvester.</li>
                  <li>Harvesters are custom built to your needs (1 to 12 rows) and are 100% stainless steel construction.</li>
                </ul>
                <div class="ctr">
                  <p>Click here to download printable brochure.</p>
                  Harvester Video<br>
                  <object width="425" height="344">
                  <param name="movie" value="http://www.youtube.com/v/EciURvL15Zw&hl=en&fs=1">
                  </param>
                  <param name="allowFullScreen" value="true">
                  </param>
                  <param name="allowscriptaccess" value="always">
                  </param>
                  <embed src="http://www.youtube.com/v/EciURvL15Zw&hl=en&fs=1" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="425" height="344"></embed>
                  </object>
              </div></td>
            </tr>
          </table>
Hope that helps.
E. Michael Brandt
www.divahtml.com
www.divahtml.com/products/scripts_dreamweaver_extensions.php
Standards-compliant scripts and Dreamweaver Extensions
www.valleywebdesigns.com/vwd_Vdw.asp
JustSo PictureWindow
JustSo PhotoAlbum, et alia

BW Web Report Issue - Result set too large

Hi,
When I execute a BEx Query on Web I am getting “Result set too large ; data retrieval restricted by configuration (maximum = 500000 cells)”.
Following to my search in SDN I understood we can remove this restriction either across the BW system globally or for a specific query at WAD template.
In my 7x Web template I am trying to increase default max no of rows parameters, As per the below inputs from SAP Note: 1127156.
But I can’t find parameter “Size Restriction for Result Sets” for any of the web items (Analysis/Web Template properties/Data Provider properties)….in the WAD Web template
Please advise where/how can I locate the properites
Instructions provided in SAP Note…
The following steps describe how to change the "safety belt" for Query Views:
1. Use the context menu Properties / Data Provider in a BEx Web Application to maintain the "safety belt" for a Query View.
2. Choose the register "Size Restriction for Result Sets".
3. Choose an entry from the dropdown box to specify the maximum number of cells for the result set.
The following values are available:
o Maximum Number
o Default Number
o Custom-Defined Number
Behind "Maximum Number" and "Default Number" you can find the current numbers defined in the customizing table RSADMIN (see below).
4. Save the Query View and use it in another Web Template.
Thanks in advance

Hi Yasemin,
Thanks for all help...i was off couple of days.
To activate it I can suggest to create a dummy template, add your query in it, add a menu bar component add an action to save the query view. Then you run the template and change the size restriction for result set then you can save it by the menu.
Can you please elaborate on the solution provided,I created dummy template with analysis and Menu bar item...i couldn't able to configure menu bar item...
Thanks in advance

Blank vertical spacing too large

Similar Messages

Maybe you are looking for