BlazeDS configuration help

Hi
I need some help on blazeDS.I am pretty new to blazeDS.i am finding it difficult to configure remote configuraton from my flex builder.I have got a coldfusion server which is deployed inside the Weblogic server as a web application.So i choose my server as ColdFusion and selected deployed in J2EE(Radio button) Whenever i select ValidateConfiguration I get the error LiveDataService not installed in the specified location.My requirement is i need to call both CFCs as well as Java classes .It will be of great help if somone helps me out to get my configuration right.
Regards
Sidd

Hi jatin4rise,the Root folder pointing to the root folder of your web application

Similar Messages

1941W configuration help needed

Our Deployment Scenario:-
1941W Gigabit Ethernet 0/0 is connected to the PPOE connection of the ISP.
Gigabit Ethernet 0/1 is connected to the wired LAN
I have created 2 wireless radio Cisco_Kamran_BGN which is operating at 2.4 Ghz Devices and Cisco_Kamran_A which is operating at 5Ghz Devices.
I have created 2 VLans for the Wireless.
Vlan 10 for Cisco_Kamran_A        192.168.10.x
Vlan 11 for Cisco _Kamran_BGN   192.168.11.X
The problem is the Wireless users are not getting the IP address from the respective DHCP server which has been configured on the Router.
Can please any from the community help me and show me where I am missing the configuration.
Please find my router & ap configuration below.
Router Configuration
Router#
sh run
Building configuration...
Current configuration : 3022 bytes
! No configuration change since last restart
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable secret 5 $1$TdQt$npYeaf/W0kRElcfMggzJ31
no aaa new-model
service-module wlan-ap 0 bootimage autonomous
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.50
ip dhcp excluded-address 192.168.10.1 192.168.10.10
ip dhcp excluded-address 192.168.11.1 192.168.11.10
ip dhcp pool DHCP
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_A
network 192.168.11.0 255.255.255.0
default-router 192.168.11.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_BGN
network 192.168.10.0 255.255.255.0
default-router 192.168.10.1
dns-server 195.225.241.222 213.42.20.20
multilink bundle-name authenticated
crypto pki token default removal timeout 0
license udi pid CISCO1941W-E/K9 sn FCZ1553C1VK
hw-module ism 0
redundancy
bridge irb
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered GigabitEthernet0/0
arp timeout 0
no mop enabled
no mop sysid
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface Wlan-GigabitEthernet0/0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface Vlan1
no ip address
interface Vlan10
ip address 192.168.10.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Vlan11
ip address 192.168.11.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
ppp authentication pap callin
ppp pap sent-username xxxxxx password 0 xxxxxx
ppp ipcp route default
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list DSL_ACCESSLIST interface Dialer1 overload
ip access-list extended DSL_ACCESSLIST
permit ip 192.168.0.0 0.0.255.255 any
control-plane
line con 0
password xxxxxx
login
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password xxxxxx
login
transport input all
scheduler allocate 20000 1000
end
Router#
Router#
Router#
Access Point Configuration
ap#
ap#
ap#
sh run
Building configuration...
Current configuration : 2603 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$JxdQ$a2/00bWJuhUKP9QLC94YD/
no aaa new-model
dot11 syslog
dot11 ssid Cisco_Kamran_A
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 1045081417161C5A555C7A7B
dot11 ssid Cisco_Kamran_BGN
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 020D05561907017015165949
username Cisco password 7 14341B180F0B
bridge irb
interface Dot11Radio0
description 802.11bgn radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
broadcast-key change 3600
ssid Cisco_Kamran_BGN
antenna gain 0
station-role root
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1
description 802.11a radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid Cisco_Kamran_A
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.10
description 802.11a bridge
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0.11
description 802.11bgn bridge
encapsulation dot1Q 11
no ip route-cache
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
no activation-character
line vty 0 4
login local
end
ap#
ap#
ap#

Hi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting     Started with Wireless - View the full discussion
conf t
interface     Dot11Radio0
no ssid     Cisco_Kamran_BGN
no encryption mode     ciphers aes-ccm
exit
interface     Dot11Radio1
no encryption mode     ciphers aes-ccm
no ssid     Cisco_Kamran_A
exit
dot11 ssid     Cisco_Kamran_A
vlan 10
dot11 ssid     Cisco_Kamran_BGN
vlan 11
exit
interface     Dot11Radio0
encryption vlan 11     mode ciphers aes
ssid     Cisco_Kamran_BGN
exit
interface     dot11radio0.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio 0.11
encapsulation     dot1q 11
bridge-group 11
Configuration of     subinterfaces and main interface
within the same bridge     group is not permitted
exit
interface     Dot11Radio1
encryption vlan 10     mode ciphers aes-ccm
ssid     Cisco_Kamran_A
interface     dot11radio1.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio1.10
encapuslation     dot1q 10
bridge-group 10
Configuration of subinterfaces and main     interface
within the same bridge     group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home

Need configuration help on producing dial tone

Hello Experts,
I have a Cisco 2921 router with VWIC3-2MFT-T1/E1 card. On this card we have T1-CAS digital line connected. We have been provided with a set of DID numbers. We have a requirement where, when we dial a DID, the router should provide a dial tone, and should allow the user to dial to extension numbers. Not sure if this is feasible. If at all possible, will need to some configuration help.
Thanks
Arabinda

Sure it's possible. What's the T1 connected to? The router will offer two-stage dialing (aka dial tone) when the incoming POTS dial-peer does not have the 'direct-inward-dial' command on it. The router will accept any input and search for an outbound dial-peer (or ephone-dn for locally registered DNs) to match. Be careful if the T1 is connected to the PSTN as this is a toll fraud risk. You need to use CoR to reign in what outbound dial-peers are available to it.
Dial Peer Basics:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010ae1c.shtml
Class of Restrictions:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a008019d649.shtml
Please remember to rate helpful responses and identify helpful or correct answers.

Multiple ethernet network adaptors + MySQL/php5: configuration help needed

I would be grateful if someone could give me some advice on how to configure multiple ethernet adapters under OS X 10.5.6
I have set up my system to work nicely with two ethernet network adapters, each with its own fixed IP. This bit works just fine. The machine supports two separate servers - a mail server and the OS X Apache2 server. I have configured the mail server to only listen to one of the IPs, and the Apache2 server to listen to the other (via httpd.conf). The system also has MySQL and php5 installed / enabled, and these services are only used by the Apache2 server.
The problem I have is that when I start the machine, initially the php5 system cannot connect reliably to the MySQL database system. The fix I have found is to temporarily make the ethernet adapter connected to the mail server 'inactive'. While this is so, the php5/MySQL connection to Apache2 works. Curiously, once an initial connection between php5 and MySQL has been made, subsequently I can make the mail server's ethernet adapter active again without further problems.
I initially thought this might be due to 'service order' issues - but changing the service order (e.g. putting the Apache adapter 'above' the mail adapter in the service order does not help. The fix only works by making the mail adapter inactive temporarily.
I suspect that there is some configuration change I can make to clarify the setup I have. The MySQL and Apache installations only need to talk to the Apache server - but I am not sure how to record this configuration in the OS X system.
Thanks in advance for any assistance that you can provide.
Message was edited by: Gavin Lawrie

Hi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting     Started with Wireless - View the full discussion
conf t
interface     Dot11Radio0
no ssid     Cisco_Kamran_BGN
no encryption mode     ciphers aes-ccm
exit
interface     Dot11Radio1
no encryption mode     ciphers aes-ccm
no ssid     Cisco_Kamran_A
exit
dot11 ssid     Cisco_Kamran_A
vlan 10
dot11 ssid     Cisco_Kamran_BGN
vlan 11
exit
interface     Dot11Radio0
encryption vlan 11     mode ciphers aes
ssid     Cisco_Kamran_BGN
exit
interface     dot11radio0.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio 0.11
encapsulation     dot1q 11
bridge-group 11
Configuration of     subinterfaces and main interface
within the same bridge     group is not permitted
exit
interface     Dot11Radio1
encryption vlan 10     mode ciphers aes-ccm
ssid     Cisco_Kamran_A
interface     dot11radio1.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio1.10
encapuslation     dot1q 10
bridge-group 10
Configuration of subinterfaces and main     interface
within the same bridge     group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home

Quick upload not configured Help

Quick upload not configured Help Why and how do I configure? Host ?, username, password?

I have exactly the same question, using almost the same system: MacBook Pro, OS X Mountain Lion (10.8.3).
What to do? I cannot find an answer for how do I configure? Host, Username? Password?

Windows 2008 Server Configuration - Help

Hello All,
I am not an expert in configuring servers and I have just started to learn. Please forgive me if I am doing something funny!
I have a router with static IP address and DHCP enabled on the router. The router had the following configuration as shown below and the clients were obtaining IP address from the router and using the internet without a problem.
Router Configutaion:
Basic Setting:
IP Address : 122.165.60.160 (My Wan Static IP)
IP Subnet Mask : 255.255.252.0
Gateway IP: 122.165.60.1
DNS Address:
Primary DNS : 203.145.184.32
Secondary DNS: 203.145.184.13
Lan TCP/IP Setup:
IP Address: 192.168.2.1 (Router IP)
IP Subnet Mask: 255.255.255.0
DHCP Enabled:
Statring IP : 192.168.2.11
Ending IP: 192.168.2.100
Now, I have installed Windows 2008 R2 Server with Active Directory, DNS and DHCP, IIS. I have created a few users and did nothing more than that in the server.
Server IP Settings
Server IP: 192.168.2.5
Subnet : 255.255.255.0
Gateway : 192.168.2.1
DNS: 127.0.0.1
And when I tried to join the domain i created... corp.globe.com the clients were not able to find the domain I therefore changed the following settings in the router.
DNS Address:
Primary DNS : 203.145.184.32
Secondary DNS: 192.168.2.5 (Server IP)
After this change the clients were able to join the domain and login as well. However the clients were getting the IP from the router. I am facing a lot of problems as listed below.
1. I am not able to ping the clients using the computer name from the server.
2. Clients cannot ping other clients or server using name. (Suppose if I try... PING SYS1 .... It looks like it is trying to ping some 92.x.x.xx IP address) even if SYS1 IP address is 192.168.2.13
3. Clients can access Internet, but I cannot browse anything in the server.
Please help me in the configuration, or point me to some guide which describes the same. I tried to set up and enable the DHCP server using Windows 2008 machine and I disabled it DHCP on the router, clients where able to get the IP address from Windows 2008
server, but they were not able to use internet. Please advise.
Thanks for your time.

Hi,
And you cannot ping the clients using the computer name from the server?
Did you turn off the firewall on server and client?
If you are having problems connecting to Active Directory and you have already successfully verified network connectivity, there might be a name resolution problem. For more and detail information, please refer to:
http://technet.microsoft.com/en-us/library/cc961921.aspx
Regards.
Vivian Wang

Automatic payment program configuration help u0096 Very urgentu0085

Hi all,
We have couple of house banks for a company code and have ranked them as 1 and 2 for the payment method (example: Check) so, how would or where can the user has an option to choose a house bank to pay his vendors. I saw that in the vendor master we can maintain the house bank however, that ignores the ranking maintained in the configuration and will always pick that back for processing the payments for that vendor but, we do not want to maintain in the vendor master.
Hence, can anyone tell me how that ranking thing works meaning how would SAP or why would SAP choose the second or third ranked bank in processing the payments? As far as I know we do not use the parameter house bank in F110 then where can we control what bank to use to process the payments for the vendors?
Your help in this regard is highly appreciated and rewarded with points
Thanks in advance
Kumar

Hi Kumar,
I think this setting is given in the T.Code "FBZP" under the heading Bank determination, wherein you have a selection "Available Amounts", I think if the amounts in that particular House Bank is exhausted, it will shift to the next House Bank in the Ordering level. You can just give it a try.
Regards
Sridhar

SFTP adapter Configuration help:

Dear All,
I am trying to configure SFTP (seeburger) in sap PI.
I want to know how to connect SFTP adapter of seeburger with an SSH sever. (I have installed free SSH Server in my laptop).
How to connect using SFTP SETTING as
AUTHENTICAION Method: Private Key authorisation
how to generate/use private key.
Please Advice,
Prakash
Edited by: senthilprakash selvaraj on Jan 20, 2010 6:42 AM

Dear All,
I have installed SSH server and genreated the RSA key in Visual admin and i have configured the SFTP adater properly.
Now i have a different issue.
In Communication channel monitoring once i start the channel(SFTP) i am not getting any message. Its just saying Channel started and thats it. nothin else is coming. not even throwing any error. what should i do. why its happing like that.
I Tried with Authentication mode as Private Key as well as Password. in both configurations are proper.
also i tried refreshing the cache..no use.
Please help,
Senthilprakash

Small configure help please? I have 3 300-28 switches, I want to connect them and avoid stp (stp setup)

HI!
I have a small network. I have 3 300-28 cisco switches. I already connected my 3 servers and clients with the switch 1 and now I want to add more clients and I need to add my other two switches in the network. Please guide me with the simple configuration So I can connect them all and avoid loop (stp). Thanks

Hi Nagaraja Thanthry!
Thanks for your reply. I am implementing it tomorrow. By just conecting the switches together at trunk ports will there be no loop? I don't want my network chowk. I hope it will work well. I might need further help, please reply.
1. I will do setting on all switches. Assign IP addresses to switches (to Vlan 1 default).
2. Set one port (e.g 28) as trunk and all others as Access on all three switches.
3. Then I will connect the switches with each other at trunk ports. Hope there will be no loop in this setting.
4. Do I need to set any setting for stp in switches ?
Please reply one by one thanks.
I am using 192.168.0.1 255.255.255.0 IP range.
Best Regards,

857 Wireless configuration help

Can someone help me with a wireless setup of an 857. I have done this in the past but can't remember the details. Basically I want very simple setup with WPA-PSK. The SDM interface is very confusing and I could do with the basic CLI for this.
Thanks

please see this link for the 857 initial configuration:
http://www.cisco.com/en/US/products/hw/routers/ps380/products_installation_guide_chapter09186a0080471066.html
this is a step-by-step for SDM and CLI basic configuration.

Ultra 10 and Creator 3D Configuration Help

Hi.
First post. Like so many others, I wanted to try Sun systems, so I got an Ultra 10 off eBay. I didn't have a 13W3 connector or monitor, so I pulled the Creator 3D card, and installed Solaris 9, using the built-in ATI video. Now that my 13W3 to HD15 adaptor has come in, I'm trying to get the 3D card back into the system, and I'm having trouble configuring it.
It took me a while to find out that FFBCONFIG is not in Solaris 9, (at least it doesn't show up in a "find file" search of local storage) and then a short time to learn about M64CONFIG. I ran the M64CONFIG from a terminal window in the CDE, and it seemed to take, but I still get the "Can't find driver for console framebuffer" error upon reboots after re-installing the 3D card. The system halts while trying to load X. Everything up to that point (with the exception of the above alert) seems correct, so I know it's just the card and the configuration. I know the card works, because on bootup, the Sun logo is different with the card in, as opposed to the ATI Sun logo, and, of course, I DO have video...
I used the M640 file with M64CONFIG and the -defaults option while configuring with the ATI card as my video source, because that's the only file in the directory, then re-installed the 3D. Did I miss a step somewhere?
Oh- I'm still a real Solaris newbie, so if you could answer in plain English, rather than a lot of UNIXSpeak it prevents my lips from moving while I'm reading and thus, not look like an idiot! :-)
If I didn't supply enough information here, just let me know and I'll add whatever's needed. Thanks.
Aside from this issue, so far it's been a blast!
..Joe

just re-install the OS
Where's the fun in that? :)
Actually, that's my last resort. The reason I'm trying to avoid it is because this way, I get to learn how to do it the hardware way.
Perhaps you would be kind enough to anser one question on re-installing the OS: Were I to do that, will it overwrite all the files I have changed, and do a completely clean, new install? I had a devil of a time getting the workstation configured for internet access. I would have the ability to see the web, but only by IP addressing. DNS wasn't working, and a friend who's a Sun engineer changed one NIS file and got it working fine. Would that get overwritten? Also, I have downloaded several programs (Open Office, FireFox, etc.): Would those remain after a new OS install?
Thanks for all the help.
..Joe

WLC2106 + LAP1131AG configuration help request

Greetings Everyone.
One of my customers asked me to configure a WLC 2106 and 2 LAP 1131AG (lightweight) for corporate/guest Wifi.
Basicly they want to implement a good wifi connection for internal use and a guest one with different QoS. The two lans
should both have dhcp but they must bet kept segregated so that none from the Guest wifi can access corporate resources.
Since i've never configured a WLC from scrath i lightly supposed it would be quite straigh forward as routers and switches from Cisco.
Unfortunately i was totally wrong.
I've downloaded the "Cisco Wireless LAN ControllerConfiguration Guide" (Soft.Release 6.0 June 2009) and after i red it i made up this workflow
for the configurations:
1) Configure Controller: (via serial)
     -     Set Management Interface parameters (IP- SM - Def GW - Dhcp server IP)
     -     Set Ap-Manager Interface parameters
     -     Virtual Interface parameters
     -     Set Admin Credentials
     -     Dhcp Configuration (internal and/or external)
2) Ap registration on the controller
     -     Configure vlan with dhcp request redirection to the dhcp server
3) Configure Wlan following customer's requests.
     -     Configure Wlan Auth for Corporate/Guest Wifi
     -     Configure QoS for both Wlans
Unfortunately i'm experiencing issue while trying joining the AP to the WLC.
It appers that the IT guy of my customer tried to configure one of the Ap.
In that Ap's flash i find files referring to a "mesh" configuration like:
mesh_cfg.txt - mesh_port_cfg.txt
which are not present on the other Ap.
I've tried to register both the Ap using:
1) Internal DHCP
2) External DHCP (microsoft W2k8 R2)
3) External DHCP (non cisco router)
But as a matter of fact they got the ip from dhcp but they don't show up in the WLC GUI.
So, resuming my issues sounds like:
1) Can't make Ap join the WLC
2) There are configuratin file on one Ap that i can't clear
3) DHCP configuration is probably wrong.
Since i'm quite lost, i'm ready to learn from anyone who could spare some time helping me out.
Thank you in advance!
Regards
Alessio
P.S.
Ap version is the following:
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(21a)JHB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 11-Aug-10 15:39 by prod_rel_team
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)

Good Day Everyone.
After a long fight, the insights of Stephen and Scott and:
https://supportforums.cisco.com/docs/DOC-13960 and
https://supportforums.cisco.com/thread/2003153
I finally managed to wipe the old configuration and to configure a LAP 1131 attached to one of the POE of the controller.
After having configured a Wlan and having set the correct DHCP redirection i'm able to connect and get an ip! (WHOA!)
I've had to set a manual ip address on the AP (let's call AP1 from now on) and to manually point it to the controller.
I was thinking about using this configuration at the customer's site getting ips from the internal DHCP and thus letting employees using the internal resources of the company.
With the same idea, i started to configure the second AP (AP2 from now on).
So i set up a dynamic interface, always on physical port 1 of the controller, gave it an ip address on another class.
Got into the antenna via console and set an ip accordingly.
I expected the controller and the antenna to communicate immediately as the AP1 did before BUT:
LWAPP_CLIENT_ERROR_DEBUG: spamHandleJoinTimer: Did not recieve the Join response
LWAPP_CLIENT_ERROR_DEBUG: No more AP manager IP addresses remain.
%SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN RESPONSE.
%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.
And keep reloading itself on, and on, and guess? Yes, on.
I'm sure i took a wrong step somewhere, could someone be so kind to enlighten me about it?
Thanks in advance!
Alessio

BlazeDS configuration with coldfusion/java No destination 'testClass' exists in service flex.messaging.services.RemotingService"

Hi
I have an application which requires interaction with both coldfusion and java.I have taken the configuration files from the blazeDS turnkey project and added it to my application.My application server is coldfusion deployed in a weblogic.I was able to call coldfusion from my flex but whenever i try making java calls i get the following error
[RPC Fault faultString="No destination 'testClass' exists in service flex.messaging.services.RemotingService" faultCode="Server.Processing" faultDetail="null"]
services-config file is as follows
<?xml version="1.0" encoding="UTF-8"?>
<services-config>
    <services>
        <service-include file-path="remoting-config.xml" />
        
    </services>
    <security>
        <login-command class="flex.messaging.security.JRunLoginCommand" server="JRun"/>
        
        
    </security>
    <channels>
        
        <channel-definition id="my-cfamf" class="mx.messaging.channels.AMFChannel">
            <endpoint uri="http://localhost:7002/flex2gateway/" class="flex.messaging.endpoints.AMFEndpoint"/>
            <properties>
                <polling-enabled>false</polling-enabled>
                <serialization>
                    <instantiate-types>false</instantiate-types>
                </serialization>
            </properties>
        </channel-definition>
        <channel-definition id="cf-polling-amf" class="mx.messaging.channels.AMFChannel">
            <endpoint uri="http://{server.name}:{server.port}{context.root}/flex2gateway/cfamfpolling" class="flex.messaging.endpoints.AMFEndpoint"/>
            <properties>
                <polling-enabled>true</polling-enabled>
                <polling-interval-seconds>8</polling-interval-seconds>
                <serialization>
                    <instantiate-types>false</instantiate-types>
                </serialization>
            </properties>
        </channel-definition>
        <channel-definition id="my-cfamf-secure" class="mx.messaging.channels.SecureAMFChannel">
            <endpoint uri="https://{server.name}:{server.port}{context.root}/flex2gateway/cfamfsecure" class="flex.messaging.endpoints.SecureAMFEndpoint"/>
            <properties>
                <polling-enabled>false</polling-enabled>
                <serialization>
                    <instantiate-types>false</instantiate-types>
                </serialization>
            </properties>
        </channel-definition>
        
        <channel-definition id="java-amf" class="mx.messaging.channels.AMFChannel">
            <endpoint uri="http://localhost:7002/flex2gateway/amf" class="flex.messaging.endpoints.AMFEndpoint"/>
        </channel-definition>
        <channel-definition id="java-secure-amf" class="mx.messaging.channels.SecureAMFChannel">
            <endpoint uri="https://{server.name}:{server.port}{context.root}/flex2gateway/amfsecure" class="flex.messaging.endpoints.SecureAMFEndpoint"/>
        </channel-definition>
        <channel-definition id="java-polling-amf" class="mx.messaging.channels.AMFChannel">
            <endpoint uri="http://{server.name}:{server.port}{context.root}/flex2gateway/amfpolling" class="flex.messaging.endpoints.AMFEndpoint"/>
            <properties>
                <polling-enabled>true</polling-enabled>
                <polling-interval-seconds>8</polling-interval-seconds>
            </properties>
        </channel-definition>
        
    </channels>
    <logging>
        <target class="flex.messaging.log.ConsoleTarget" level="Error">
            <properties>
                <prefix>[BlazeDS] </prefix>
                <includeDate>false</includeDate>
                <includeTime>false</includeTime>
                <includeLevel>false</includeLevel>
                <includeCategory>false</includeCategory>
            </properties>
            <filters>
                <pattern>Endpoint.*</pattern>
                <pattern>Service.*</pattern>
                <pattern>Configuration</pattern>
                <pattern>Message.*</pattern>
            </filters>
        </target>
    </logging>
    <system>
       
        
    </system>
</services-config>
remote-config.xml
<?xml version="1.0" encoding="UTF-8"?>
<service id="remoting-service"
    class="flex.messaging.services.RemotingService"
    messageTypes="flex.messaging.messages.RemotingMessage">
    <adapters>
        <adapter-definition id="cf-object" class="coldfusion.flash.messaging.ColdFusionAdapter" default="true"/>
        <adapter-definition id="java-object" class="flex.messaging.services.remoting.adapters.JavaAdapter"/>
    </adapters>
    <default-channels>
        <channel ref="my-cfamf"/>
    </default-channels>
    <destination id="ColdFusion">
        <channels>
            <channel ref="my-cfamf"/>
        </channels>
        <properties>
            <source>*</source>
            
            <access>
                
                <use-mappings>false</use-mappings>
                
                <method-access-level>remote</method-access-level>
            </access>
            <property-case>
                
                <force-cfc-lowercase>false</force-cfc-lowercase>
                
                <force-query-lowercase>false</force-query-lowercase>
                
                <force-struct-lowercase>false</force-struct-lowercase>
            </property-case>
        </properties>
    </destination>
<destination id="testClass">
        <properties>
                <source>TestClass</source>
        </properties>
<adapter ref="java-object" />
        <channels>
            <channel ref="java-amf"/>
        </channels>
    </destination>
    <destination id="testClass2">
        <properties>
                <source>TestClass2</source>
        </properties>
<adapter ref="java-object"/>
        <channels>
            <channel ref="java-amf"/>
        </channels>
    </destination>
</service>
Can anyone please tell me where i m going wrong.Is that because i m using flex2gateway for java calls?.I used it since it was how it has been configured in the turnkey project for coldfusion.I have replicated the file as it was there and since it is using flex2gateway even for javaEndpoints i felt we could use the same.
regards
Sidd

Thanks for the reply. Yes, I did compile all the Java and it
works OK with a simple Java program. It just will not work in a
Flex application.
The java classes are:
RRA:
package blah.myPackage;
import java.util.List;
import java.util.Collection;
import flex.data.DataSyncException;
import flex.data.assemblers.AbstractAssembler;
class RRA extends AbstractAssembler
public Collection fill( List fillParameters )
RRS service = new RRS();
return service.getSome();
RRS:
package blah.myPackage;
import java.util.ArrayList;
import java.util.List;
import java.sql.*;
import flex.EORS.*;
class RRS
public List getSome()
ArrayList list = new ArrayList();
String str = "bob";
RR rr = new RR(str);
list.add(rr);
return list;
RR:
package blah.myPackage;
class RR
private String name;
public RR() { }
public RR(String name)
this.name = name;
public String getName()
return this.name;
public void setName(String name)
this.name = name;
I started with something that retrieved data from a database
but watered it down just to try and get some kind of communication
between Flex and Java.

Authentication Configuration Help

All,
Can anyone help me configure user authentication for my WAP. I have an Aironet 1242 and all the documentation I come across is showing me how to configure it for administration purposes. I have a Radius server up and running but I can't get the config right to have users authenticate to it when they access the WAP.
Below is my config.
version 12.3
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
hostname 4TH_FLOOR_CONF
enable secret xxx
clock timezone EST -5
clock summer-time EDT recurring 2 Sun Mar 2:00 1 Sun Nov 2:00
ip subnet-zero
ip domain name sba.gov
ip dhcp excluded-address 165.110.30.1 165.110.30.229
ip dhcp excluded-address 165.110.30.240 165.110.30.254
ip dhcp pool atlantis
network 105.120.35.0 255.255.255.0
ip dhcp-server 105.120.35.252
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
dot11 ssid airbender
dot11 ssid avatar
authentication open
guest-mode
power inline negotiation prestandard source
username Cisco password xxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
ssid airbender
ssid avatar
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
ssid avatar
speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
hold-queue 160 in
interface BVI1
ip address 105.120.35.219 255.255.255.0
no ip route-cache
ip default-gateway 105.120.35.254
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server local
nas 105.120.35.12 key xxx
radius-server attribute 32 include-in-access-req format %h
radius-server host 165.110.30.215 auth-port 1812 acct-port 1646 key xxx
radius-server vsa send accounting
control-plane
bridge 1 route ip
line con 0
line vty 0 4
sntp server 105.120.35.253
end

You are missing half of the config for security:
you still need to setup the ssid
read here:
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801bd035.shtml

Basic Internet Routing Configuration Help -- Cisco 2811

Hi everyone,
I want to start by saying that I brought a Cisco 2811 Router to use at home and to practice advanced networking with. So far, I believe I've configured everything as it should be, however, I am not getting any internet connection.
DHCP is set up and working properly, I can lease addresses without issue.
Both interfaces are configured, fe0/1 with a static IP, and fe0/0 as a DHCP client.
I have connected fe0/0 directly to the Cable modem and it acquires an IP without issue. Connecting my laptop directly into fe0/1 allows my laptop to lease an IP from the router's DHCP server. So I know everything up to there is working properly. I've set up NAT as best I can with what I know, but I am still not getting the router to provide internet access.
The following is my Router's Configuration. Does anything seem to be missing? I used Configuration Professional to set it up.
------------Begin Configuration-------------
Building configuration...
Current configuration : 2570 bytes
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname Network
boot-start-marker
boot-end-marker
security authentication failure rate 10 log
security passwords min-length 6
no logging buffered
logging console critical
enable secret 5 $1$4FJS$RQUEiWuTaMOAGhVx1O1Du0
enable password 7 046F03070C291D175F40
aaa new-model
aaa authentication login local_auth local
aaa session-id common
dot11 syslog
no ip source-route
no ip routing
no ip gratuitous-arps
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.100.1
ip dhcp pool Network
import all
network 192.168.100.0 255.255.255.0
dns-server 4.2.2.2 4.2.2.1
lease 7
no ip bootp server
ip domain name Network
ip name-server 4.2.2.2
ip name-server 4.2.2.1
login block-for 5 attempts 5 within 1
multilink bundle-name authenticated
voice-card 0
no dspfarm
username Admin password 7 1526035D5D7C72252B3B
archive
log config
hidekeys
interface FastEthernet0/0
description $ETH-WAN$
ip address dhcp client-id FastEthernet0/0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly
no ip route-cache
duplex full
speed auto
no mop enabled
interface FastEthernet0/1
ip address 192.168.100.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
no ip route-cache
duplex full
speed auto
no mop enabled
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat pool Network 192.168.100.1 192.168.100.254 netmask 255.255.255.0
ip nat inside source list 101 interface FastEthernet0/0 overload
logging trap debugging
logging facility local2
access-list 100 permit udp any any eq bootpc
access-list 101 remark INTERNET ACCESS THROUGH NAT
access-list 101 remark CCP_ACL Category=2
access-list 101 permit ip 192.168.100.0 0.0.0.255 any
dialer-list 1 protocol ip permit
snmp-server community public RO
no cdp run
control-plane
banner motd ^C Welcome! ^C
line con 0
login authentication local_auth
transport output telnet
line aux 0
exec-timeout 15 0
login authentication local_auth
transport output telnet
line vty 0 4
password 7 107D0C1A10051B1F15
login authentication local_auth
transport input telnet
scheduler allocate 20000 1000
end
------------------End Configuration-------------------
Does anything seem amiss? Thank you all in advance for your help!
John

Hi Again,
I sent
dhcp pool Network
default-router 192.168.100.1
to the router and wrote it to config. I still didn't have internet access at first, so I followed John's tip and hooked up my machine to an old Catalyst 2849G switch I had laying around. The switch has no settings, just gets an ip from the router and does its own thing. After doing so, I do now have internet access. I'm using it to post this reply in fact.
Here are the results of ipconfig /all on my Ethernet NIC on my machine before even having the switch:
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . : hsd1.ut.comcast.net.
Description . . . . . . . . . . . : Intel(R) Ethernet Connection I217-LM
Physical Address. . . . . . . . . : 54-EE-75-27-6F-06
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::7cdd:83b5:e603:127e%13(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.100.2(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Thursday, October 02, 2014 7:57:10 AM
Lease Expires . . . . . . . . . . : Thursday, October 09, 2014 7:57:10 AM
Default Gateway . . . . . . . . . :
DHCP Server . . . . . . . . . . . : 192.168.100.1
DHCPv6 IAID . . . . . . . . . . . : 290778741
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-1B-B2-3D-AF-54-EE-75-27-6F-06
DNS Servers . . . . . . . . . . . : 75.75.76.76
75.75.75.75
NetBIOS over Tcpip. . . . . . . . : Enabled
It seems everything was working as it should, but I didn't have internet access and windows still reported it as an unknown network.
After hooking up my Switch, Windows reported seeing 'Network' (From my router's host name, I presume?) and once I reset the modem, I had internet access.
This was a huge learning experience and I am glad to have help from all of you. Is there anything else I can to do optimize my configurations? Also, why didn't I have internet access when directed hooked up to FastEthernet0/1 even though my machine acquired IP's and DNS info?
Here is another copy of the running config with today's changes:
---------------------Begin Configuration------------------------
Building configuration...
Current configuration : 2401 bytes
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname Network
boot-start-marker
boot-end-marker
security authentication failure rate 10 log
security passwords min-length 6
logging buffered 4096
logging console critical
enable secret 5 $1$4FJS$RQUEiWuTaMOAGhVx1O1Du0
enable password 7 046F03070C291D175F40
aaa new-model
aaa authentication login local_auth local
aaa session-id common
dot11 syslog
no ip source-route
no ip gratuitous-arps
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.100.1
ip dhcp pool Network
import all
network 192.168.100.0 255.255.255.0
default-router 192.168.100.1
lease 7
no ip bootp server
ip domain name Network
login block-for 5 attempts 5 within 1
multilink bundle-name authenticated
voice-card 0
no dspfarm
username Admin password 7 1526035D5D7C72252B3B
archive
log config
hidekeys
interface FastEthernet0/0
description $ETH-WAN$
ip address dhcp client-id FastEthernet0/0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly
duplex full
speed auto
no mop enabled
interface FastEthernet0/1
ip address 192.168.100.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
duplex full
speed auto
no mop enabled
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 dhcp
ip http server
no ip http secure-server
ip nat pool Network 192.168.100.1 192.168.100.254 netmask 255.255.255.0
ip nat inside source list 10 interface FastEthernet0/0 overload
logging trap debugging
logging facility local2
access-list 10 permit 192.168.100.0 0.0.0.255
access-list 100 permit udp any any eq bootpc
dialer-list 1 protocol ip permit
snmp-server community public RO
no cdp run
control-plane
banner motd ^C Welcome! ^C
line con 0
login authentication local_auth
transport output telnet
line aux 0
exec-timeout 15 0
login authentication local_auth
transport output telnet
line vty 0 4
password 7 107D0C1A10051B1F15
login authentication local_auth
transport input telnet
scheduler allocate 20000 1000
end
--------------------------End Configuration-------------------------
Let me know if there is anything else you guys need or I should do, I'll be back after classes today. Thanks again!
-John

BlazeDS configuration help

Similar Messages

Maybe you are looking for