Blinking amber light for an invalid IP address

I'm stuck! This is the first time I've bought an Apple product and it took me more than 5 minutes to get it working! I just got the Airport Extreme and can't get it to connect to my cable modem.
If I plug the modem to my iMac my internet connection works just fine. If I connect the modem to the Airport Extreme router, it just blinks amber and the manual setup says it can't get an IP address.
I have Time Warner Cable in San Diego and they told me my network settings are Automatic/DHCP. I've tried power cycling on all of the devices, but still can't get rid of the blinking amber light.
I've tried searching apple.com/support/airport and the forums and can't find anything.
Anyone got any ideas?

Hello jianwakain. Welcome to the Apple Discussions!
You just need to make sure you are providing sufficient time for a complete power recycle of your network components to allow the modem to "recognize" the new device connected to it.
Modem/Router Power Recycling - Quick
o Power-off the Cable modem, AEBSn, & computer(s); Wait at least 5 minutes.
o Power-on the Cable modem; Wait at least 5 minutes.
o Power-on the AEBSn; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the Cable modem, AEBSn, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the Cable modem; Wait at least 30 minutes.
o Power-on the AEBSn; Wait at least 5 minutes.
o Power-on the computer(s)

Similar Messages

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light.

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?

apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together.

First time startup- Blinking amber light. Not sure what to do.

So I just got my airport express and when i first started getting the airport utility downloaded for windows xp, i used my modem (time warner ubee modem) ethernet cable and all but I am just getting a blinking amber light. I don't know if it hasn't configured if I need to wait longer for to initally start. I am kind of derp when it comes to networking, so..

A persistent, flashing amber light indicates that any of the several potential conditions may require your attention:
The base station has not yet been configured because it is new, or the reset switch has been set.
You have selected a security configuration that is not recommended.
One of several other conditions, such as a disconnected Ethernet cable or invalid IP address has been detected.
(ref: http://docs.info.apple.com/article.html?artnum=305101)
If you run the AirPort Utility, it will show an amber circle on the summary page next to the area(s) causing the problem. Click on this amber circle and it should provide an explanation. Please post back your findings.

Airport Express 801.11b/g and the neverending, unconfigurable blinking amber light

Gather round and let me tell you a tale. Once upon a time I bought an airport express 801.11b/g and I was very happy to use it for airtunes, extending a wi-fi network and the wireless printing capabilities. One day, it beagn flashing a scaaaary amber light. The base station stopped showing up in my airport utility 5.6 as well. The only way to get it to show up, was to hard reset it, and lose all the configurations I once enjoyed happily. After the hard reset, It would show up in the utility, and I would reconfigure it to do all its cool things it once did, and it would restart. But sadly, after restarting the blinking amber light came on a again. It would also not show up in the utility unless I hard reset it again, and the same thing happened over and over and over until I felt like pulling my hair out.
I decided to get another airport express a few months later, ultimately deciding that the unit must have just been defective. Bad luck. But - the second unit literally went through the SAME EXACT THING. Worked for a while, then onto the blinking amber light- hard reset- reconfigure-blinking amber light thing. Over and over and over. Just like the first one. The end.
So - either Im missing something totally fundamental or I had the misfortune of getting two defective units in a row. Both were bought used from different places, and worked "fine" for previous owners. Am I corrupting these things or what?
I have spent literally hours trying all the resets, configuring "workarounds" and nothing works. For both of them.
What do I do with these two devices? I don't need two shiny white paperweights.
Please advise,
Thanks.

Yes. It seems an integral part of the set up process though, you don't have to seperately configure the airport do you?
My wireless security is WPA/WPA2 Personal. When I go through the standard network set up, it automatically enters my wireless security settings. So it doesn't really seem to give an option to specifically set that option on the airport if that makes sense?
I did go through maunual mode to try that with the same result:
If I'm using the airports own network and connect to the wifi, no security, then I'm getting airtunes from my macbook. Of course this means it's plugged into my router via ethernet which isn't any use to me as I want it in my kitchen, and would rather not limit my apple devices to b/g when I have a decent N router, and would also mean running a huge ethernet cable across my house!
The seller has said it worked for him but he's not up to scratch on his tech, so if I'm sure it's malfunctioning he'll refund. Obviously this is great news and he seems like a very nice guy so I want to be certain it's not me malfunctioning before I send it back!
So in summary I have it functioning on it's OWN network:
Wireless mode: Create a wireless network
Wireless network name: Apple Network XXXXXX
etc
Once 'wireless mode' is switched from 'create a wireless network' to 'join a wireless network' I select my current WiFi, security and password, checked the TCP/IP settings all good. Select 'Update'. Get the warning that device and network will be temporarily unavailable am I sure I want to continue. Then it goes through the same as before, says it's succesful, restarts to flashing amber with no way of accessing it unless I hard reset.
Thanks for the help so far...

Airport extreme blinking amber light error when connecting to new modem

I have just bought and installed a new modem gateway. It is an Arris TG852G DOC 3.0 model with a built in WiFi router.
After connecting it and activating it through Comcast, I reset, then reconnected my airport extreme MD0331LL/A Model No. A1408 to the new Arris
modem, I am getting blinking amber lights on the base station. I have internet connectivity, but I am still getting an amber light. My wireless devices (ipad and iphones) all see the old network name and id and seem to work just fine.
When I scanned for my airport base station in my airport utility (version 5.6.1) to try to resolve the error message I get
a message stating that the Airport Utility is not detecting any airport devices.
I cannot reset the default settings as these buttons do not work within the Airport Utility.
I suspect interference between the built in router in the Arris and I understand I need to operate it in bridge mode. Can you please help me fix this.
The COMCAST people are extremely unhelpful, and stated that this is not their problem but a problem with my router
as they have provifded me internet connectivity through the modem and the issue is my problem.

Try connecting an Ethernet cable from your computer directly to one of the LAN <-> ports on the AirPort Extreme to see if AirPort Utility can detect the AirPort Extreme that way.
If yes, click on the AirPort Extreme and then click directly on the word Status (2nd line on the summary page)
A window will open to explain why the amber light is blinking
If the message indicates that you need to configure the AirPort in Bridge Mode......
Click the Internet icon at the top of the window
Click the Internet Connection tab just below
Change the setting for Connection Sharing to Off (Bridge Mode)
Click Update at the lower right of the window to save the new setting and restart the AirPort Extreme
You can disconnect the Ethernet cable that you were using to configure the AirPort Extreme now
It would be a good idea to power off both the Arris gateway and the AirPort Extreme now
Wait a minute
Start the Arris first, and let it run a full minute
Start the AirPort Extreme next the same way
You should be all set

A blinking amber light doesn't necessarily mean that something is wrong.

Yesterday I set up a new AEBSn in bridge mode so that an attached hard disk could be shared by two Mac computers connecting to the AEBSn wirelessly pending inauguration of a new DSL connection.
Although the configuration worked perfectly, the amber light continually blinked because the AEBSn sensed that an Ethernet cable was unplugged even though the configuration did not call for any Ethernet connections.
Interestingly, the blinking amber light turned to solid green as soon as I added two network printers via Ethernet cables.

Just wanted to make sure you know that if the amber light is blinking, you can run the new Airport Utility and when the wireless devices appear on the left hand side of the page, anyone that is flasking amber will show up with a flashing amber light. If you double click on that device a new window will come up. On the summary page you'll see a line that says name of device and it will have a status light next to it that is the same as the status light on the equipment. In this case a flashing amber light. If you double click on the flashing symbol it will give you the reason for the flashing amber light.
In most cases at this point, the flashing amber light is usually because there was no security applied to the system.
If you opt, you can also turn off the amber light if you can live with the problem.

MIFI4620LE Jetpack blinking amber light--does this mean the battery is bad? Should the unit operate without the battery installed if plugged in?

MIFI4620LE Jetpack blinking amber light--does this mean the battery is bad? Should the unit operate without the battery installed if plugged in?

The MIFI4620LE Jetpack does not work without a battery installed, even when connected to an external power supply.
I personally think that was a dumb design. I would think the unit would use more electricity when continually charging the battery than just powering the unit it's self, but that's the way Novatel made them.
If your Jetpack works with the battery installed and connected to an external power supply, but does not power on with power supply disconnected, I would say that the battery is defective or worn out.
You should be able to go to a nearby Verizon Store and have them either test the battery or put a new one in it to see if it works. Then you will know if you need to spend the $$ for a new battery. OR if you always use your Jetpack at home, or in your car, just use the old battery connect to a power supply or your cigarette lighter and save the cash.
As the Customer Support person stated, the slow blinking amber light is a normal state when the Jetpack is turned on and connected to Verizon's service.
I hope this solves your problem.

Still have blinking amber light

I've followed the instructions. I've searched the support board, and I still can't get my airport express to work. I've reset it to factory settings, I've unplugged the cable modem and left it off for 15 minutes then replugged everything.
My Macbook "sees" the airport, it says the AX is working, but there's no Internet connection (blinking amber light). I have two AX's set up elsewhere just fine, but I'm trying to set this one up with no luck.
HELP!

Hi Mary,
Welcome to the forum.
First question is: How old is the Express that is a problem? If it is two years or older it may have reached the end of its life cycle.
After you have reset it to factory settings, it should show up in the setup assistant or Airport Utility with its original Apple factory ID. When you join it to the system, do not name it the same name that you have named it before. What I usually do is add a word in front of the old name like "new" or add a number behind it. It may see the Airport but if the Airport is in actually not tied to your wireless system it won't connect.

AX - blinking amber light

Three days ago, I was happily using my AX to access the internet. Then two days ago I disconnected the AX in order to use the ethernet cable for something else. But when I went to plug the cable back in, I started to get a blinking amber light. I've since did a hard reset to no avail -- still getting the light. Strangely, when I plug the ethernet cable into my computer directly, I'm able to surf the internet happily. Why doesn't the AX connect to the internet?
Thanks for your help in advance.

Always be sure to allow enough time for a complete power recycle of your network components when changing configurations ...
Modem/Router Power Recycling - Quick
o Power-off the DSL/Cable modem, Internet router, & computer(s); Wait at least 5 minutes.
o Power-on the DSL/Cable modem; Wait at least 5 minutes.
o Power-on the Internet router; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the DSL/Cable modem, Internet router, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the DSL/Cable modem; Wait at least 30 minutes.
o Power-on the Internet router; Wait at least 5 minutes.
o Power-on the computer(s)

Constant blinking amber light

Just got the Airport Express, and am trying to transition over from Linksys. I have a constant blinking amber light and its saying that Airport Express cant find the base station. Any help is much appreciated.

If you are replacing the Linksys with the new AirPort Express, I would suggest that you start by performing a complete power recycle of all of your networking hardware. Please check out the following AirPort User tip for details.

Airport extreme slow blinking amber light. Can't see through airport utility.

Unsuccesful trying to reset. On a hard reset, it still goes from steady amber to slow blinking amber. Never get a rapid blinking amber light. Have tried to connect directly to it via ethernet and airport utility doesn't see it. Any help?

I have this same issue. Internet works, I can connect to it, but i doesn't show in the Airport Utility. Also, it doesn't let me connect to other computers or my AirDIsk. I am using 10.5. Unplug and plugin style reset fixes it...for a while. Any ideas anyone?

Airport not "recognizing" network - blinking amber light

I just got a new Airport Express. I plugged it in hooked up the ethernet cable to it and all I get is the blinking amber light.
I thought it might need the Cable modem restarted so I did that. Nothing.
I thought it might be an issue with my Vonage adapter. I rebooted that. Nothing.
I bypassed the Vonage completely by directly going from cable modem to Airport Express. Nothing.
I've tried everything but it isn't working.
iBook G4 Mac OS X (10.4.7) 1.33mHz 14.1" 768ram 60gb HD

Any time when you reset you have to do it in a specific order to make it work correctly.
The normal reset sequence is to Pull the power adapter from the ISP's Modem and then your Airport Express or Extreme and shut your computer clear off.and next you wait for everything to reset to default settings. (Normally 5 minutes). After your wait you have to plug in the Modem first, wait until it re acquires the signal and all the lights (normally 3) depending on the modem you have. Next Plug in your express or Extreme and again you have to wait a minute and then you can restart your computer.
Be sure before you start the sequence you have the correct setting in System preferences and Network to Airport. and drag it to the top of the list and it has to be highlighted with the little green dot,and be sure you go up to the icon next to your HELP for signal strength and make sure your Airport is ON.
And last welcome to the discussions
Cheers Don

TS1589 Help, blinking amber light.

My airport express shows the blinking amber light. I've tried to reset it but since I've got no luck at all it seems the reset button isn't working. My airport utility wont find the airport express, I tried finding it with wi-fi/ethernet but it wont come up. Ideas?

Be sure to press and hold the reset button for sufficient time for the LED to blink rapidly, then release it. It will take five to ten seconds. It will then illuminate solid amber for about a minute, after which it will flash amber, slowly. That is when AirPort Utility should be able to recognize it.
You should feel, and may hear, a barely perceptible click when you press the button. There are anecdotal reports of users who may have damaged the reset button by pressing too hard, so don't do that.

Airport Utility cannot find Time Capsule and has a blinking amber light

I have a wireless router for my Wifi set up through AT&T (2WIRE). I am trying to add my TC to my existing network rather than establishing a new Wifi network with it. When I try to plug in my TC to set it up, Airport Utility cannot even find it. My TC has a blinking amber light also. I have tried reseting my TC, resetting my router, unplugging my router, unplugging my TC... I have the latest version of Air Port utility (6.2 (620.33)).

Connect the TC LAN port to the computer by ethernet.
If necessary do a reset of the TC so it shows up.
Put the TC into bridge mode.
Go to the wireless page, and set wireless to off.
Update the TC.. disconnect from the PC and plug WAN port to LAN port of the 2wire with ethernet.
The TC will now exist as a client in your network without creating a second wireless network.
You should also be able to access the TC via the airport utility.
I do think you should use the TC wireless since the 2wire does not provide a signal at 5ghz which is much faster than 2.4ghz.
So I do suggest you in fact do use the wireless but it is up to you.
It makes no difference having two wireless networks if they both connect back to the same router.
Do not use the "Join a wireless network" method.. ie no cable between the TC and 2wire.. that is poorest possible setup.

Trying to resolve a blinking amber light on my Time Capsule. The problem is i don't see the airport utilities under Apps/Utilities..any ideas?

trying to resolve a blinking amber light on my Time Capsule. The problem is i don't see the airport utilities under Apps/Utilities to try and reset..any ideas?

AirPort Utility should be here: Macintosh HD > Applications > Utilities > AirPort Utility
If it is not there, you can download it from here:
http://support.apple.com/downloads/#airport
Temporarily, connect an Etherent cable from your Mac to one of the LAN <-> ports on the back of the Time Capsule
Open AirPort Utility - Click Manual Setup
Click directly on the word Status (2nd line) and a window will open to explain why the Time Capsule is complaining along with suggested actions to remedy the issue

Blinking amber light for an invalid IP address

Similar Messages

Maybe you are looking for